Search Results

Search found 17625 results on 705 pages for 'techno log'.

Page 643/705 | < Previous Page | 639 640 641 642 643 644 645 646 647 648 649 650  | Next Page >

  • My computer's dying :(

    - by j-t-s
    Hi All I have a sweet computer and have never had any real problems with it until now. I recently formatted my computer and all was well. But now my monitor randomly flickers. The monitor will just go black for about a second or two, then it'll return back to its normal state with all the stuff still on the screen. This is getting progressively worse. Another problem that has started is my computer randomly restarts. (I've managed to prevent it from restarting by removing the check in Automatically Restart from the Startup and Recovery Dialog. But I know this doesn't solve the problem). It also completely freezes up on me. One last thing, this morning I got a big blue screen. I can't remember what it said, but if it happens again I will take note of it and repost. Or if I can find some kind of a log file containing that bluescreen error I will post. I have checked all cords, and they're all fine. Nothing's loose. My computer isn't overheating either. I've taken the case off for 3 whole days and haven't used the computer for those 3 days, which has had no effect. I've checked the connections inside and nothing's loose there either. I know there's nothing wrong with my monitor because my friend has 2 computers and it works perfectly on those computers. I don't understand how my computer could suddenly become so unstable. I'm almost certain that I have no viruses; I full-scan my pc everyday for nastys, and have strict firewall settings. Anyway, I don't see how it could be a virus anyway simply due to the fact that I had these problems right after I formatted, and before I even had the chance to install or copy anything or even connect to the internet. I know it has nothing to do with the way I formatted the computer too, I've been fixing computers for years. Sorry for rambling on, just making sure I don't leave anything out. Has anybody else had this problem? Can somebody please try to help me with this? Thank you :)

    Read the article

  • "Hostile" network in the company - please comment on a security setup

    - by TomTom
    I have a little specific problem here that I want (need) to solve in a satisfactory way. My company has multiple (IPv4) networks that are controlled by our router sitting in the middle. Typical smaller shop setup. There is now one additional network that has an IP Range OUTSIDE of our control, connected to the internet with another router OUTSIDE of our control. Call it a project network that is part of another companies network and combined via VPN they set up. This means: They control the router that is used for this network and They can reconfigure things so that they can access the machines in this network. The network is physically split on our end through some VLAN capable switches as it covers three locations. At one end there is the router the other company controls. I Need / want to give the machines used in this network access to my company network. In fact, it may be good to make them part of my active directory domain. The people working on those machines are part of my company. BUT - I need to do so without compromising the security of my company network from outside influence. Any sort of router integration using the externally controlled router is out by this idea So, my idea is this: We accept the IPv4 address space and network topology in this network is not under our control. We seek alternatives to integrate those machines into our company network. The 2 concepts I came up with are: Use some sort of VPN - have the machines log into VPN. Thanks to them using modern windows, this could be transparent DirectAccess. This essentially treats the other IP space not different than any restaurant network a laptop of the company goes in. Alternatively - establish IPv6 routing to this ethernet segment. But - and this is a trick - block all IPv6 packets in the switch before they hit the third party controlled router, so that even IF they turn on IPv6 on that thing (not used now, but they could do it) they would get not a single packet. The switch can nicely do that by pulling all IPv6 traffic coming to that port into a separate VLAN (based on ethernet protocol type). Anyone sees a problem with using he switch to isolate the outer from IPv6? Any security hole? It is sad we have to treat this network as hostile - would be a lot easier - but the support personnel there is of "known dubious quality" and the legal side is clear - we can not fulfill our obligations when we integrate them into our company while they are under a jurisdiction we don't have a say in.

    Read the article

  • Volume group disappeared, LVs still available

    - by Ben
    I've run into an issue with my KVM host which runs VMs on a LVM volume. As of last night the logical volumes are no longer seen as such (I can't create snapshots of them even though I have been for months now). Running any scans all result in nothing being found: [root@apollo ~]# pvscan No matching physical volumes found [root@apollo ~]# vgscan Reading all physical volumes. This may take a while... No volume groups found root@apollo ~]# lvscan No volume groups found If I try restoring the VG conf backup from /etc/lvm/backups/vg0 I get the following error: [root@apollo ~]# vgcfgrestore -f /etc/lvm/backup/vg0 vg0 Couldn't find device with uuid 20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt. Cannot restore Volume Group vg0 with 1 PVs marked as missing. Restore failed. /etc/lvm/backups/vg0 has the following for the physical volume: physical_volumes { pv0 { id = "20zG25-H8MU-UQPf-u0hD-NftW-ngsC-mG63dt" device = "/dev/sda5" # Hint only status = ["ALLOCATABLE"] flags = [] dev_size = 4292870143 # 1.99902 Terabytes pe_start = 384 pe_count = 524031 # 1.99902 Terabytes } } fdisk -l /dev/sda shows the following: [root@apollo ~]# fdisk -l /dev/sda Disk /dev/sda: 6000.1 GB, 6000069312512 bytes 64 heads, 32 sectors/track, 5722112 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000188b7 Device Boot Start End Blocks Id System /dev/sda1 2 32768 33553408 82 Linux swap / Solaris /dev/sda2 32769 33280 524288 83 Linux /dev/sda3 33281 1081856 1073741824 83 Linux /dev/sda4 1081857 3177984 2146435072 85 Linux extended /dev/sda5 1081857 3177984 2146435071+ 8e Linux LVM The server is running a 4 disk HW RAID10 which seems perfectly healthy according to megacli and smartd. The only odd message in /var/log/messages is the following which shows up every couple of hours: Jun 10 09:41:57 apollo udevd[527]: failed to create queue file: No space left on device Output of df -h [root@apollo ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1016G 119G 847G 13% / /dev/sda2 508M 67M 416M 14% /boot Does anyone have any ideas what to do next? The VMs are all running fine at the moment apart from not being able to snapshot them. Updated with extra info It's not a lack of inodes: [root@apollo ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 67108864 48066 67060798 1% / /dev/sda2 32768 47 32721 1% /boot pvs, vgs & lvs either output nothing or "No volume groups found".

    Read the article

  • Disk IO causing high load on Xen/CentOS guest

    - by Peter Lindqvist
    I'm having serious issues with a xen based server, this is on the guest partition. It's a paravirtualized CentOS 5.5. The following numbers are taken from top while copying a large file over the network. If i copy the file another time the speed decreases in relation to load average. So the second time it's half the speed of the first time. It needs some time to cool off after this. Load average slowly decreases until it's once again usable. ls / takes about 30 seconds. top - 13:26:44 up 13 days, 21:44, 2 users, load average: 7.03, 5.08, 3.15 Tasks: 134 total, 2 running, 132 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.1%sy, 0.0%ni, 25.3%id, 74.5%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1048752k total, 1041460k used, 7292k free, 3116k buffers Swap: 2129912k total, 40k used, 2129872k free, 904740k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1506 root 10 -5 0 0 0 S 0.3 0.0 0:03.94 cifsd 1 root 15 0 2172 644 556 S 0.0 0.1 0:00.08 init Meanwhile the host is ~0.5 load avg and steady over time. ~50% wait Server hardware is dual xeon, 3gb ram, 170gb scsi 320 10k rpm, and shouldn't have any problems with copying files over the network. disk = [ "tap:aio:/vm/dev01.img,xvda,w" ] I also get these in the log INFO: task syslogd:1350 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syslogd D 00062E4F 2208 1350 1 1353 1312 (NOTLB) c0ef0ed0 00000286 6e71a411 00062e4f c0ef0f18 00000009 c0f20000 6e738bfd 00062e4f 0001e7ec c0f2010c c181a724 c1abd200 00000000 ffffffff c0ef0ecc c041a180 00000000 c0ef0ed8 c03d6a50 00000000 00000000 c03d6a00 00000000 Call Trace: [<c041a180>] __wake_up+0x2a/0x3d [<ee06a1ea>] log_wait_commit+0x80/0xc7 [jbd] [<c043128b>] autoremove_wake_function+0x0/0x2d [<ee065661>] journal_stop+0x195/0x1ba [jbd] [<c0490a32>] __writeback_single_inode+0x1a3/0x2af [<c04568ea>] do_writepages+0x2b/0x32 [<c045239b>] __filemap_fdatawrite_range+0x66/0x72 [<c04910ce>] sync_inode+0x19/0x24 [<ee09b007>] ext3_sync_file+0xaf/0xc4 [ext3] [<c047426f>] do_fsync+0x41/0x83 [<c04742ce>] __do_fsync+0x1d/0x2b [<c0405413>] syscall_call+0x7/0xb ======================= I have tried disabling irqbalanced as suggested here but it does not seem to make any difference.

    Read the article

  • Setting up a WPA-PSK network card to connect to a WPA2 network

    - by mattshepherd
    I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

    Read the article

  • How can I troubleshoot Virtualbox port forwarding from Windows guest to OSX host not working?

    - by joe larson
    There are a plethora of questions about virtual box port forwarding problems but none with my specific details. I have a Windows install living in Virtual Box, hosted within OSX. I've got several webservers running on localhost on different ports within the Windows install. I cannot for the life of me get port forwarding to work so I can access those webservers from OSX. My settings look like this (yes I have a NAT adapter): And in my vbox configuration file the relavent portion looks like this: <NAT> <DNS pass-domain="true" use-proxy="false" use-host-resolver="false"/> <Alias logging="false" proxy-only="false" use-same-ports="false"/> <Forwarding name="RLPWeb" proto="1" hostport="7084" guestip="127.0.0.1" guestport="7084"/> <Forwarding name="UtilWeb" proto="1" hostport="4040" guestip="127.0.0.1" guestport="4040"/> <Forwarding name="WCARLP" proto="1" hostport="8084" guestip="127.0.0.1" guestport="8084"/> <Forwarding name="WCAUtil" proto="1" hostport="4848" guestip="127.0.0.1" guestport="4848"/> </NAT> I've turned off the Windows firewall to ensure it is not interfering, and I am not running a firewall on OSX. Anyway, when I attempt to go to for example http://127.0.0.1:4040/ on any of my OSX browsers, it will eventually time out. The log file for this VM shows that it is correctly reading the settings and implying it's doing the right thing here: 00:00:08.286 NAT: set redirect TCP host port 4848 => guest port 4848 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 8084 => guest port 8084 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 4040 => guest port 4040 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 7084 => guest port 7084 @ 127.0.0.1 00:00:08.290 Changing the VM state from 'LOADING' to 'SUSPENDED'. 00:00:08.290 Changing the VM state from 'SUSPENDED' to 'RESUMING'. 00:00:08.290 Changing the VM state from 'RESUMING' to 'RUNNING'. 00:00:08.337 Display::handleDisplayResize(): uScreenId = 0, pvVRAM=000000012017d000 w=1834 h=929 bpp=32 cbLine=0x1CA8, flags=0x1 00:00:09.139 AIOMgr: Host limits number of active IO requests to 16. Expect a performance impact. 00:00:13.454 NAT: DHCP offered IP address 10.0.2.15 I've tried setting the Host IP to 127.0.0.1, and I've tried setting Guest IP blank and also 10.0.2.15. None of these seem to help. What else can I look at to troubleshoot this issue? Details of setup: OSX 10.6.8 Windows 7 Professional 64bit VirtualBox 4.1.2

    Read the article

  • Passenger 2.2.4, nginx 0.7.61 and SSL

    - by boompa
    Has anyone had any luck configuring Passenger and nginx with SSL? I've spent hours trying to get this configuration working as I'd like, using what few resources there are out there on the net, and I can't get any of the supposedly forwarded headers to show up in the Rails controller. For example, with a conf file of the following (and multiple variations thereof): server { listen 3000; server_name .example.com; root /Users/website/public; passenger_enabled on; rails_env development; } server { listen 3443; root /Users/website/public; rails_env development; passenger_enabled on; ssl on; #ssl_verify_client on; ssl_certificate /Users/website/ssl/server.crt; ssl_certificate_key /Users/website/ssl/server.key; #ssl_client_certificate /Users/website/ssl/CA.crt; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1; ssl_ciphers ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-SSL-Subject $ssl_client_s_dn; #proxy_set_header X-SSL-Issuer $ssl_client_i_dn; proxy_redirect off; proxy_max_temp_file_size 0; } and Rails code in the controller like this: request.headers.each { |k, v| RAILS_DEFAULT_LOGGER.error "Header #{k} Val #{v}" } other headers appear, but not those set in nginx, e.g.: Header rack.multithread Val false Header REQUEST_URI Val /login/new Header REMOTE_PORT Val 64021 Header rack.multiprocess Val true Header PASSENGER_USE_GLOBAL_QUEUE Val false Header PASSENGER_APP_TYPE Val rails Header SCGI Val 1 Header SERVER_PORT Val 3443 Header HTTP_ACCEPT_CHARSET Val ISO-8859-1,utf-8;q=0.7,*;q=0.7 Header rack.request.query_hash Val Header DOCUMENT_ROOT Val /Users/website/public I've even gone so far as to modify Passenger's abstract_request_handler's main_loop method, i.e., headers, input = parse_request(client) if headers if headers[REQUEST_METHOD] == PING process_ping(headers, input, client) else headers.each { |h,v| log.unknown "abstract_request_handler: #{h} = #{v}" } process_request(headers, input, client) end end only to find that the supposedly added headers do not exist there either: abstract_request_handler: HTTP_KEEP_ALIVE = 300 abstract_request_handler: HTTP_USER_AGENT = Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1) Gecko/20090624 Firefox/3.5 abstract_request_handler: PASSENGER_SPAWN_METHOD = smart-lv2 abstract_request_handler: CONTENT_LENGTH = 0 abstract_request_handler: HTTP_IF_NONE_MATCH = "b6e8b9afbc1110ee3bf0c87e119252ad" abstract_request_handler: HTTP_ACCEPT_LANGUAGE = en-us,en;q=0.5 abstract_request_handler: SERVER_PROTOCOL = HTTP/1.1 abstract_request_handler: HTTPS = on abstract_request_handler: REMOTE_ADDR = 127.0.0.1 abstract_request_handler: SERVER_SOFTWARE = nginx/0.7.61 abstract_request_handler: SERVER_ADDR = 127.0.0.1 abstract_request_handler: SCRIPT_NAME = abstract_request_handler: PASSENGER_ENVIRONMENT = development abstract_request_handler: REMOTE_PORT = 64021 abstract_request_handler: REQUEST_URI = /login/new abstract_request_handler: HTTP_ACCEPT_CHARSET = ISO-8859-1,utf-8;q=0.7,*;q=0.7 abstract_request_handler: SERVER_PORT = 3443 abstract_request_handler: SCGI = 1 abstract_request_handler: PASSENGER_APP_TYPE = rails abstract_request_handler: PASSENGER_USE_GLOBAL_QUEUE = false I'm tired of banging my head against the wall, so I'd truly appreciate any help I can get!

    Read the article

  • Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

    - by BraeburnDev
    I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

    Read the article

  • Certain Programs cannot access internet

    - by Cindy
    Operating System: Windows 7 (x64) Problem: Certain Programs are unable to access the internet. They claim that there is no connection when you already are connected. Hello, before we start. Just letting you know I'm new here, and I'm very new to Windows 7. I installed it two days ago. I just installed Windows 7 on my laptop and I have a few problems. I play World of Warcraft, as well as a variety of games. And when I first attempt to log into the game, I get a windows error message, but it doesn't stop there. I thought World of Warcraft got corrupted during the upgrade. It seems that I am unable to access the internet from other online games as well. Most say in along the lines of "Cannot connect to patch server, try again later." I cannot use a downloader Also, I have internet explorer. The x32 version of the browser cannot connect to the internet, and when I try to enter "google.com", it says the same thing. I'm only accessing this site through Internet Explorer x64, which I would have been fine with is it's compatible with Adobe Flash. The only thing that seems to connect to the internet are Internet Explorer x64 and Windows Live Messenger. Here are the steps I have taken, but none worked. 1.) Disable Windows Firewall 2.) Have Windows Firewall Enabled, but allow the specific programs to access internet. And allowed all incoming access. 3.) Disabled UAC, Ran the programs as an admin, and set compatibility to Vista. 4.) Uninstalled an anti-virus program. (McAffee Security Suite 2010) 5.) Reinstalled the programs 6.) Reinstalled Windows 7 7.) Retaken the steps on the Administrator account. Please assist me in this problem. I need to get back into the game. Thanks so much in advance.

    Read the article

  • Apache ProxyPass Missing Images

    - by EpicOfChaos
    I have a apache server that sits in front of my glassfish server. mydomain.com goes directly to my static files on apache, than if you hit the subdomain forum.mydomain.com it goes to the glassfish webapp forum/ at 127.0.0.1:8080/forum/. This proxy seems to work it takes me to the web app but all of the images are missing! Here is how I go my virtual host setup. NameVirtualHost *:80 <VirtualHost *:80> ServerName www.mydomain.com ServerAlias subdomain.mydomain.com mydomain.com DocumentRoot "/usr/local/apache/htdocs" </VirtualHost> <VirtualHost *:80> ServerName forum.mydomain.com # any logging config, etc, that you need ProxyPass / http://127.0.0.1:8080/forum/ ProxyPassReverse / http://127.0.0.1:8080/forum/ </VirtualHost> And in the access log this is what I am seeing. [15/Jan/2012:03:28:02 +0000] "GET /forums/list.page HTTP/1.1" 200 12861 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/logo.jpg HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/styles/style.css?1326582403934 HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_recentTopics.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_search.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_members.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/styles/en_US.css?1326582403934 HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_groups.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_big.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_login.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/whosonline.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/icon_mini_register.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/ping_session.jsp HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_lock.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder.gif HTTP/1.1" 404 1075 [15/Jan/2012:03:28:02 +0000] "GET /forum/templates/default/images/folder_new.gif HTTP/1.1" 404 1075 Any Ideas why the images are not working?

    Read the article

  • mint linux, DVD drive keeps randomly being accessed. unsure how to find culprit

    - by juicebox
    I have a workstation with mint linux 12. It seems like the DVD drive on the machine keeps randomly "activating". By activating it makes noise, the light turns on, and it seems like it is checking if a disk is in it. At first I thought I was being hacked and someone/something was trying to check if I had media in the DVDRom drive. I ruled that out with netstat and rkhunter. I checked my logs and the only thing I can find that might help point out the problem are these repeated chunks in syslog: Mar 24 17:47:31 rich-MINT kernel: [ 9846.551422] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 16392 in Mar 24 17:47:31 rich-MINT kernel: [ 9846.551424] res 51/40:01:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error) Mar 24 17:47:31 rich-MINT kernel: [ 9846.551427] ata2.00: status: { DRDY ERR } Mar 24 17:47:31 rich-MINT kernel: [ 9846.551433] ata2.00: hard resetting link Mar 24 17:47:32 rich-MINT kernel: [ 9846.868012] ata2.01: hard resetting link Mar 24 17:47:32 rich-MINT kernel: [ 9847.344054] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Mar 24 17:47:32 rich-MINT kernel: [ 9847.344067] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 24 17:47:32 rich-MINT kernel: [ 9847.376118] ata2.00: configured for PIO0 Mar 24 17:47:32 rich-MINT kernel: [ 9847.393047] ata2.01: configured for UDMA/133 Mar 24 17:47:32 rich-MINT kernel: [ 9847.397046] ata2: EH complete and again Mar 24 17:55:28 rich-MINT kernel: [10323.633268] sr 1:0:0:0: ioctl_internal_command return code = 8000002 Mar 24 17:55:28 rich-MINT kernel: [10323.633270] : Sense Key : Aborted Command [current] [descriptor] Mar 24 17:55:28 rich-MINT kernel: [10323.633275] : Add. Sense: No additional sense information Mar 24 17:55:11 rich-MINT kernel: [10306.640009] ata2.00: link is slow to respond, please be patient (ready=0) Mar 24 17:55:16 rich-MINT kernel: [10310.840009] ata2.00: SRST failed (errno=-16) Mar 24 17:55:16 rich-MINT kernel: [10310.840016] ata2.00: hard resetting link Mar 24 17:55:16 rich-MINT kernel: [10311.160013] ata2.01: hard resetting link Mar 24 17:55:16 rich-MINT kernel: [10311.636061] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Mar 24 17:55:16 rich-MINT kernel: [10311.636075] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 24 17:55:16 rich-MINT kernel: [10311.668122] ata2.00: configured for PIO0 Mar 24 17:55:16 rich-MINT kernel: [10311.684854] ata2.01: configured for UDMA/133 Mar 24 17:55:17 rich-MINT kernel: [10312.105473] ata2: EH complete (Copied from Pastebin - http://pastebin.com/YNDrnyzH) If any linux masters could take a quick look at these log outputs and help me understand what is going on , much appreciated.

    Read the article

  • Wake On Lan only works on first boot, not sequent ones

    - by sp3ctum
    I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

    Read the article

  • Windows 8 with LiveID login authenticates as Guest to remote SQl Server

    - by Tim Long
    I have a network where several users are using Office Accounting 2009 in multi-user client/server mode. OA is built on SQL Server. One PC acts as the 'server' and has the SQl Server instance, the others have only the application installed and no SQL instance, all of the apps connect remotely to the SQL instance on the 'server'. I'm using the term 'server' loosely here, it is just a normal workstation that happens to be designated as the server and runs the SQL instance. There is no NT domain, all user accounts are local accounts. The way that OA works in multi-user mode is that each user is required to have a local account with the same username and password on both the client and 'server' PCs. This has been working well, no along comes Windows 8. I use my 'Microsoft Account' aka LiveID to log into Windows 8. Office Accounting runs fine and attempts to connect to the database, but fails, 'you do not have permission to perform this operation'. In the SQL logs, I get this error: 2012-10-28 17:54:01.32 Logon Error: 18456, Severity: 14, State: 11. 2012-10-28 17:54:01.32 Logon Login failed for user 'SERVER\Guest'. Reason: Token-based server access validation failed with an infrastructure SERVER is the hostname of the server. So it seems to be authenticating as 'Guest'?? To verify this, I enabled the Guest account on the 'server' PC and then added Guest as an allowed user within Office Accounting (this simply creates the user in SQL and gives it an appropriate database role). Sure enough, My Windows 8 PC was then able to connect to the database when using Office Accounting. Clearly, having users authenticate as 'Guest' stinks from a security and auditing standpoint. So what I need are some ideas for how to work around this. I've tried switching the Windows 8 PC to a 'local account' and that works too, but requires giving up significant functionality on the Windows 8 PC. What I really need is a way to force the Windows 8 PC to use a specific set of credentials when connecting to the remote SQL instance. Office Accounting takes the logged in username, which is my LiveID and doesn't correspond to any Windows user name. Anyone solved this issue?

    Read the article

  • Problems migrating an EBS backed instance over AWS Regions

    - by gshankar
    Note: I asked this question on the EC2 forums too but haven't received any love there. Hopefully the ServerFault community will be more awesome. The new AWS Sydney region opening up is something that we've been waiting for for a long time but I'm having a lot of trouble migrating our instances over from N. California. I managed to migrate 1 instance over using CloudyScripts to move a snapshot and then firing up a new instance in the Sydney region. This was a very new instance so both the source and destination were running on a Ubuntu 12.04 LTS server and I had no issues there. However, the rest of our instances are all Ubuntu 10.04 LTS and with these, I'm having a lot of problems. I've tried following: 1- following the AWS whitepaper on moving instances which was given to us at the recent Customer Appreciation Day in Sydney where the new region was launched. The problem with this approach was with the last step (Step 19) here you register the image: ec2-register -s snap-0f62ec3f -n "Wombat" -d "migrated Wombat" --region ap-southeast-2 -a x86_64 --kernel aki-937e2ed6 --block-device-mapping "/dev/sdk=ephemeral0" I keep getting this error: Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' does not exist which I think is due to the kernel_id not existing in the Sydney region? 2- Using CloudyScripts to move a snapshot and then creating a new volume and attaching to a new instance in Sydney This results in the instance just hanging on boot and failing the status checks. I can't SSH in or look at the server log I suspect that my issue is with finding the right kernel_id for the volume in the new region. However I can't seem to work out how to go about finding this kernel_id, the ones I've tried (from the original instance) don't result in the Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' error and any other kernel_id just won't boot. I've tried both 12.04 and 10.04 versions of Ubuntu. Nothing seems to work, I've been banging my head against a wall for a while now, please help! New (broken) instance i-a1acda9b ami-9b8611a1 aki-31990e0b Source instance i-08a6664e ami-b37e2ef6 aki-937e2ed6 p.s. I also tried following this guide on updating my Ubuntu LTS version to 12.04 before doing the migration but it didn't seem to work either, still getting stuck on updating the kernel_id http://ubuntu-smoser.blogspot.com.au/2010/04/upgrading-ebs-instance.html

    Read the article

  • How to configure a tun interface on Linux for SSH port forwarding?

    - by sarshad
    I am trying to forward port 139 from a Windows machine to my Ubuntu SSH server on a tun interface with the ip address 10.0.0.1. This is so that I can access the windows shares on the machine on my Ubuntu server, through the reverse tunnel. I can forward ports to 127.0.0.1, but not to 10.0.0.1. On windows I am using the Tunnelier ssh client. On my Ubuntu server, the following message is printed in auth.log: Received disconnect from 124.109.51.154: 11: Server denied request for client-side server-2-client forwarding on 10.0.0.1:139. So far i have tried the following settings: GatewayPorts yes PermitTunnel yes AllowTcpForwarding yes in the /etc/ssh/sshd_config file, but it did not work. I set up the tun like this: sudo tunctl -t loc_0 -u myusername sudo ifconfig loc_0 inet 10.0.0.1 netmask 255.255.255.0 up The settings in the Tunneler ssh client should not matter because I can forward port 139 successfully to the Microsoft Loopback Adapter on a Windows machine running the WinSSHD server. Versions: Windows is XP SP3, Ubuntu is 10.10. Update: I tried to forward the port to a number greater than 1024 mentioning the IP address of the tun, and it successfully connected but the forwarding was done on 127.0.0.1 instead of the tun's IP address 10.0.0.1. So there are two separate problems now, when connecting from the Windows machine: 1) Forwarding on ports less than 1024 is probably being denied. How can we allow that on the server? 2) Forwarding is done only on 127.0.0.1 even if I mention 10.0.0.1 which is the tun's IP address. Another attempt: I also tried to forward port 22 of a Linux machine to the tun's port 55567. It showed success. But when I tried to ssh into that port using both local addresses, on the Linux machine in its debug display I got the error Connection failed: no route to host when using 127.0.0.1 to connect and simply Connection refused when using the tun's IP address. So the tun is not getting the forwarded port no matter we connect from a Windows client or a Linux client.

    Read the article

  • Hidden DNS master only sending notify to one slave

    - by Rob
    My hidden DNS master is only sending notifies to one of the name servers for a zone I have 3 named servers ns0,ns1 & ns2 all running bind 9.7.3.dfsg-1ubuntu4.1. When an update is processed the master (ns0) seems to behave normally. ns0 (192.168.2.50) zone domain.org/IN: sending notifies (serial 2012060703) client 192.168.2.52#42892: transfer of 'domain.org/IN': AXFR-style IXFR started: TSIG rndc-key client 192.168.2.52#42892: transfer of 'domain.org/IN': AXFR-style IXFR ended ns2 (192.168.2.52) client 192.168.2.50#3762: received notify for zone 'domain.org': TSIG 'rndc-key' zone domain.org/IN: Transfer started. transfer of 'domain.org/IN' from 192.168.2.50#53: connected using 192.168.2.52#55747 zone domain.org/IN: transferred serial 2012060704: TSIG 'rndc-key' transfer of 'domain.org/IN' from 192.168.2.50#53: Transfer completed: 1 messages, 34 records, 1028 bytes, 0.001 secs (1028000 bytes/sec) Nothing happens on ns1. I've turned up the logging level but there's no information in syslog about the actual name servers bind has sent notifications to so I guess this is something it doesn't log. I've also tried watching tcpdump, it never makes any attempt to notify ns1 only ns2 192.168.2.50.56278 > 192.168.2.52.53: [udp sum ok] 56418 notify [b2&3=0x2400] [1a] [1au] ? SOA? domain.org. domain.org. [0s] SOA ns1.domain.net. dnsmaster.domain.net. ? 2012060801 10800 3600 604800 3600 ar: rndc-key. ANY [0s] TSIG hmac-md5.sig-alg.reg.int. fudge=300 maclen=16 origid=56418 error=0 otherlen=0 (174) the authoritive zone has both ns1 and ns2 records $ORIGIN domain.org. $TTL 3h @ IN SOA ns1.domain.net. dnsmaster.domain.net. ( 2012060801 ; Serial yyyymmddnn 3h ; Refresh After 3 hours 1h ; Retry Retry after 1 hour 1w ; Expire after 1 week 1h ) ; Minimum negative caching of 1 hour @ 3600 IN NS ns1.domain.net. @ 3600 IN NS ns2.domain.net. // Edit I have added also-notify {192.168.2.51;192.168.2.52;}; explicitly to the zone file and it all works fine, both ns1 and ns2 get notify messages and transfers succeed. I was under the impression bind would automatically send notifies to all NS records on a zone, maybe it's bugged?

    Read the article

  • No Telnet login prompt when used over SSH tunnel

    - by SCO
    Hi there ! I have a device, let's call it d1, runnning a lightweight Linux. This device is NATed by my internet box/router, hence not reachable from the Internet. That device runs a telnet daemon on it, and only has root as user (no pwd). Its ip address is 192.168.0.126 on the private network. From the private network (let's say 192.168.0.x), I can do: telnet 192.168.0.126 Where 192.168.0.126 is the IP address in the private network. This works correctly. However, to allow administration, I'd need to access that device from outside of that private network. Hence, I created an SSH tunnel like this on d1 : ssh -R 4455:localhost:23 ussh@s1 s1 is a server somewhere in the private network (but this is for testing purposes only, it will endup somewhere in the Internet), running a standard Linux distro and on which I created a user called 'ussh'. s1 IP address is 192.168.0.48. When I 'telnet' with the following, let's say from c1, 192.168.0.19 : telnet -l root s1 4455 I get : Trying 192.168.0.48... Connected to 192.168.0.48. Escape character is '^]'. Connection closed by foreign host . The connection is closed after roughly 30 seconds, and I didn't log. I tried without the -l switch, without any success. I tried to 'telnet' with IP addresses instead of names to avoid reverse DNS issues (although I added to d1 /etc/hosts a line refering to s1 IP/name, just in case), no success. I tried on another port than 4455, no success. I gathered Wireshark logs from s1. I can see : s1 sends SSH data to c1, c1 ACK s1 performs an AAAA DNS request for c1, gets only the Authoritave nameservers. s1 performs an A DNS request, then gets c1's IP address s1 sends a SYN packet to c1, c1 replies with a RST/ACK s1 sends a SYN to c1, C1 RST/ACK (?) After 0.8 seconds, c1 sends a SYN to s1, s1 SYN/ACK and then c1 ACK s1 sends SSH content to d1, d1 sends an ACK back to s1 s1 retries AAAA and A DNS requests After 5 seconds, s1 retries a SYN to c1, once again it is RST/ACKed by c1. This is repeated 3 more times. The last five packets : d1 sends SSH content to s1, s1 sends ACK and FIN/ACK to c1, c1 replies with FIN/ACK, s1 sends ACK to c1. The connection seems to be closed by the telnet daemon after 22 seconds. AFAIK, there is no way to decode the SSH stream, so I'm really stuck here ... Any ideas ? Thank you !

    Read the article

  • Tomcat and IIS 7 both on different ip's and different ports

    - by n00b
    I have Tomcat and IIS 7 installed together on a Windows 2008 server. The machine has two IPs (134.133.1.1 and 134.133.2.2). I want Tomcat to handle 134.133.1.1, on port 80, and IIS to handle both 134.133.2.2, on port 80 AND 134.133.1.1, on port 443, but can't seem to get the last two together (I can get one or the other by themselves on IIS, along with the first IP address on Tomcat). I have configured Tomcat to successfully listen to ip 134.133.1.1, on port 80 with this configuration; <Connector port="80" protocol="HTTP/1.1" address="134.133.1.1" connectionTimeout="20000" redirectPort="8443" /> I also have a site configured in IIS bound to ip 134.133.1.1, on port 443 (SSL). When I turn on IIS, after Tomcat, I can reach both 134.133.1.1:80 (Tomcat) and 134.133.1.1:443 (IIS) successfully (as desired). The problem now comes when I want to introduce a new site via IIS, at the new ip address. In IIS I have setup a new site at IP 134.133.2.2, port 80. I can not start the site. The event log shows this error; Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. The data field contains the error number. I think this is because IIS 7 tries to listen to port 80 on all IPs, and it cant because Tomcat is taking port 80 for 134.133.1.1. From reading, the resolution is to specify the IP address you want IIS to bind on port 80. The problem is, when I add 134.133.2.2 to the iplisten list, then I get a 404 when I try navigating to 134.133.1.1:443. I assume this is because IIS is no longer listening to ANY port on 134.133.1.1. How do I resolve this such that IIS will return both sites? EDIT: Per request my IIS binding for site A is 134.133.2.2 on port 80 (http) and 134.133.2.2 on port 443. For site B in IIS, the binding is 134.133.1.1 on port 443 (https). Note the IPs in this example are just for example purposes, but consistent with my setup.

    Read the article

  • .htaccess template, suggestions needed

    - by purpler
    DefaultLanguage en-US FileETag None Header unset ETag ServerSignature Off SetEnv TZ Europe/Belgrade # Rewrites Options +FollowSymLinks RewriteEngine On RewriteBase / # Redirect to WWW RewriteCond %{HTTP_HOST} ^serpentineseo.com RewriteRule (.*) http://www.serpentineseo.com/$1 [R=301,L] # Redirect index to root RewriteCond %{THE_REQUEST} ^[A-Z]{3,9}\ /.*index\.html\ HTTP/ RewriteRule ^(.*)index\.html$ /$1 [R=301,L] # Cache media files: ExpiresActive On ExpiresDefault A0 # Month <filesMatch "\.(gif|jpg|jpeg|png|ico|swf|js)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> # Week <FilesMatch "\.(css|pdf)$"> Header set Cache-Control "max-age=604800" </FilesMatch> # 10 Min <FilesMatch "\.(html|htm|txt)$"> Header set Cache-Control "max-age=600" </FilesMatch> # Do not cache <FilesMatch "\.(pl|php|cgi|spl|scgi|fcgi)$"> Header unset Cache-Control </FilesMatch> # Compress output <IfModule mod_deflate.c> <FilesMatch "\.(html|js|css)$"> SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error Documents ErrorDocument 206 /error/206.html ErrorDocument 401 /error/401.html ErrorDocument 403 /error/403.html ErrorDocument 404 /error/404.html ErrorDocument 500 /error/500.html # Prevent hotlinking RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://(www\.)?serpentineseo.com/.*$ [NC] RewriteRule \.(gif|jpg|png)$ http://www.serpentineseo.com/images/angryman.png [R,L] # Prevent offline browsers RewriteCond %{HTTP_USER_AGENT} ^BlackWidow [OR] RewriteCond %{HTTP_USER_AGENT} ^Bot\ mailto:[email protected] [OR] RewriteCond %{HTTP_USER_AGENT} ^ChinaClaw [OR] RewriteCond %{HTTP_USER_AGENT} ^Custo [OR] RewriteCond %{HTTP_USER_AGENT} ^DISCo [OR] RewriteCond %{HTTP_USER_AGENT} ^Download\ Demon [OR] RewriteCond %{HTTP_USER_AGENT} ^eCatch [OR] RewriteCond %{HTTP_USER_AGENT} ^EirGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailSiphon [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailWolf [OR] RewriteCond %{HTTP_USER_AGENT} ^Express\ WebPictures [OR] RewriteCond %{HTTP_USER_AGENT} ^ExtractorPro [OR] RewriteCond %{HTTP_USER_AGENT} ^EyeNetIE [OR] RewriteCond %{HTTP_USER_AGENT} ^FlashGet [OR] RewriteCond %{HTTP_USER_AGENT} ^GetRight [OR] RewriteCond %{HTTP_USER_AGENT} ^GetWeb! [OR] RewriteCond %{HTTP_USER_AGENT} ^Go!Zilla [OR] RewriteCond %{HTTP_USER_AGENT} ^Go-Ahead-Got-It [OR] RewriteCond %{HTTP_USER_AGENT} ^GrabNet [OR] RewriteCond %{HTTP_USER_AGENT} ^Grafula [OR] RewriteCond %{HTTP_USER_AGENT} ^HMView [OR] RewriteCond %{HTTP_USER_AGENT} HTTrack [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Stripper [OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} Indy\ Library [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^InterGET [OR] RewriteCond %{HTTP_USER_AGENT} ^Internet\ Ninja [OR] RewriteCond %{HTTP_USER_AGENT} ^JetCar [OR] RewriteCond %{HTTP_USER_AGENT} ^JOC\ Web\ Spider [OR] RewriteCond %{HTTP_USER_AGENT} ^larbin [OR] RewriteCond %{HTTP_USER_AGENT} ^LeechFTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Mass\ Downloader [OR] RewriteCond %{HTTP_USER_AGENT} ^MIDown\ tool [OR] RewriteCond %{HTTP_USER_AGENT} ^Mister\ PiX [OR] RewriteCond %{HTTP_USER_AGENT} ^Navroad [OR] RewriteCond %{HTTP_USER_AGENT} ^NearSite [OR] RewriteCond %{HTTP_USER_AGENT} ^NetAnts [OR] RewriteCond %{HTTP_USER_AGENT} ^NetSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Net\ Vampire [OR] RewriteCond %{HTTP_USER_AGENT} ^NetZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Octopus [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Explorer [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Navigator [OR] RewriteCond %{HTTP_USER_AGENT} ^PageGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^Papa\ Foto [OR] RewriteCond %{HTTP_USER_AGENT} ^pavuk [OR] RewriteCond %{HTTP_USER_AGENT} ^pcBrowser [OR] RewriteCond %{HTTP_USER_AGENT} ^RealDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^ReGet [OR] RewriteCond %{HTTP_USER_AGENT} ^SiteSnagger [OR] RewriteCond %{HTTP_USER_AGENT} ^SmartDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperBot [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperHTTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Surfbot [OR] RewriteCond %{HTTP_USER_AGENT} ^tAkeOut [OR] RewriteCond %{HTTP_USER_AGENT} ^Teleport\ Pro [OR] RewriteCond %{HTTP_USER_AGENT} ^VoidEYE [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Image\ Collector [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebAuto [OR] RewriteCond %{HTTP_USER_AGENT} ^WebCopier [OR] RewriteCond %{HTTP_USER_AGENT} ^WebFetch [OR] RewriteCond %{HTTP_USER_AGENT} ^WebGo\ IS [OR] RewriteCond %{HTTP_USER_AGENT} ^WebLeacher [OR] RewriteCond %{HTTP_USER_AGENT} ^WebReaper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebSauger [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ eXtractor [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ Quester [OR] RewriteCond %{HTTP_USER_AGENT} ^WebStripper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebWhacker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Wget [OR] RewriteCond %{HTTP_USER_AGENT} ^Widow [OR] RewriteCond %{HTTP_USER_AGENT} ^WWWOFFLE [OR] RewriteCond %{HTTP_USER_AGENT} ^Xaldon\ WebSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Zeus RewriteRule ^.*$ http://www.google.com [R,L] # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Deny access to sensitive files <FilesMatch "\.(htaccess|psd|log)$"> Order Allow,Deny Deny from all </FilesMatch>

    Read the article

  • My hosting server giving memory allocation error

    - by Usman
    I have hosted my website on shared hosting linux server. As there are atmost 10-15 visitors come to my website daily but My wordpress website most of the times gives 500 Internal Server Error. I accessed my server Error Log following error is showing: [Tue Dec 04 08:57:45 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:45 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:43 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:43 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:42 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:42 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:41 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:41 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:40 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:40 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:32 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:31 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:29 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:29 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php [Tue Dec 04 08:57:26 2012] [error] [client 117.205.74.227] (12)Cannot allocate memory: couldn't create child process: /opt/suphp/sbin/suphp for /home/grasphub/public_html/index.php Is my hosting service really bad. And any solution. Thanks in advance.

    Read the article

  • 404 Error on a file that exists?

    - by Abs
    Hello all, A script makes a GET request to my URL like so: http://mydomain.com/cgi-bin/uu_ini_status_audios.pl?tmp_sid=b742be1d131c4d32237a9f1fcdca659e&rnd_id=0.2363453360320319 However, I get a 404 returned straight away: The requested URL /cgi-bin/uu_ini_status_audios.pl was not found on this server. But that script exists on my server, I can see the file! It has the correct permissions (I gave it a 777 to be sure). It is also owned by my apache user and its in the group apache. What am I missing?? Thanks for any help on this! Update I thought it would have been a htaccess (rewrite) but I don't think it is anymore. I tried putting a index.php file in there and try to access it via my URL but I can't even do that! I tried this: http://mydoamin.com/cgi-bin/index.php - same 404 error! I get this in myerror log: [Tue Sep 14 14:42:49 2010] [error] [client xx.xxx.xx.xxx] script not found or unable to stat: /var/www/vhosts/mydomain.com/cgi-bin Access_log file: xx.xxx.xx.xxx - - [14/Sep/2010:14:48:25 +0200] "GET /cgi-bin/index.php HTTP/1.1" 404 475 "-" "Mozilla/5.0 (Windows; U; Windows NT 6.0; en-US; rv:1.9.2.9) Gecko/20100824 Firefox/3.6.9 (.NET CLR 3.5.30729)" Update 2 My htaccess file: <IfModule mod_rewrite.c> RewriteEngine On RewriteRule ^blog/ - [L] RewriteCond %{HTTP_HOST} ^www\.mydomain\.com$ [NC] RewriteRule ^(.*)$ http://mydomain.com/$1 [R=301,L] RewriteRule ^search/(.*)/(.*)/(.*)/(.*) /search.php?searchfor=$1&sortby=$2&page=$3&searchterm=$4 RewriteRule ^confirmemail/(.*) /confirmemail.php?code=$1 RewriteRule ^resetpassword/(.*) /resetpassword.php?code=$1 RewriteRule ^resendconfirmation/(.*) /resendconfirmation.php?userid=$1 RewriteRule ^categories/ /categories.php RewriteRule ^([-_~*a-zA-Z0-9]+)(\/)?$ /memberprofile.php?username=$1 RewriteRule ^browse/audios/(.*)/(.*)/(.*)/(.*) /audios.php?sortby=$1&filter=$2&page=$3&title=$4 RewriteRule ^browse/categories/audios/(.*)/(.*)/(.*)/(.*) /categoryaudios.php?sortby=$1&filter=$2&page=$3&title=$4 RewriteRule ^audios/(.*)/(.*) /playaudio.php?audioid=$1&title=$2 RewriteRule ^download/audio/(.*)/(.*) /downloadaudio.php?AUDIOID=$1&title=$2 RewriteRule ^members/audios/(.*)/(.*) /memberaudios.php?pid=$1&username=$2 RewriteRule ^syndicate/audios/(.*)/(.*) /syndicateaudios.php?filter=$1&title=$2 </IfModule> Update 3 [root@smydomain ~]# ls -la /var/www/vhosts/mydoamin.com/httpdocs/cgi-bin/ total 60 drwxr-xr-x 3 apache root 4096 Sep 14 14:37 . drwxr-x--- 20 som psaserv 4096 Sep 14 14:40 .. drwxr-xr-x 2 apache root 4096 Sep 7 03:01 configs -rwxrwxrwx 1 apache root 4 Sep 14 14:37 index.php -rwxrwxrwx 1 apache apache 6520 Sep 7 03:01 uu_ini_status_audios.pl -rwxr-xr-x 1 apache root 3215 Sep 7 03:01 uu_lib_audios.pl -rwxr-xr-x 1 apache root 30249 Sep 7 03:01 uu_upload_audios.pl

    Read the article

  • How do I configure a site in IIS 7 for SSL with a wildcard certificate?

    - by michielvoo
    We have an Windows 2008 server with IIS 7 to test sites we develop for our clients. Each site has a binding on a subdomain: clienta.example.com clientb.example.com clientc.example.com (* Using example.com to protect the innocent) For one of these sites we now have to test if it works over https. So I have created a wildcard certificate request with *.example.com as the common name. I have received the certificate (issued by PositiveSSL SA) and completed the request. The certificate is now installed in IIS. Now I have added an https binding to the second site with the following settings: type: https IP address: All Unassigned Port: 443 Host name: clientb.example.com SSL certificate: *.example.com Browsing the site over regular http works fine. When I try to browse the site over https I get the following errors (depending on the browser used): Chrome This webpage is not available Error 102 (net::ERR_CONNECTION_REFUSED): Unknown error. Firefox Unable to connect Firefox can't establish a connection to the server at clientb.example.com Firebug says Status: Aborted Internet Explorer Internet Explorer cannot display the webpage I have checked Failed Request Tracing, and according to the log the request was completed with status 200. I have run the SSL Diagnostics Tool with the following result: System time: Fri, 04 Mar 2011 14:04:35 GMT Connecting to 192.168.2.95:443 Connected Handshake: 115 bytes sent Handshake: 3877 bytes received Handshake: 326 bytes sent Handshake: 59 bytes received Handshake succeeded Verifying server certificate, it might take a while... Server certificate name: *.example.com Server certificate subject: OU=Domain Control Validated, OU=PositiveSSL Wildcard, CN=*.example.com Server certificate issuer: C=GB, S=Greater Manchester, L=Salford, O=Comodo CA Limited, CN=PositiveSSL CA Server certificate validity: From 2-3-2011 1:00:00 To 2-3-2012 0:59:59 1:00:00 To 2-3-2012 0:59:59 HTTPS request: GET / HTTP/1.0 User-Agent: SSLDiag Accept:*/* HTTPS: 85 bytes of encrypted data sent HTTPS: 533 bytes of encrypted data received Status: HTTP/1.1 404 Not Found HTTP/1.1 404 Not Found Content-Type: text/html; charset=us-ascii Server: Microsoft-HTTPAPI/2.0 Date: Fri, 04 Mar 2011 14:04:35 GMT Connection: close Content-Length: 315 <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN""http://www.w3.org/TR/html4/strict.dtd"> <HTML><HEAD><TITLE>Not Found</TITLE> <META HTTP-EQUIV="Content-Type" Content="text/html; charset=us-ascii"></HEAD> <BODY><h2>Not Found</h2> <hr><p>HTTP Error 404. The requested resource is not found.</p> </BODY></HTML> HTTPS: server disconnected Final handshake: 37 bytes sent successfully Q: What can I do to make this work?

    Read the article

  • Trying to install Rmagick on Debian

    - by Janak
    One of things you need to do to get Rmagick installed apt-get install libmagick9-dev When I try that I get the following errors Reading package lists... Done Building dependency tree... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. Since you only requested a single operation it is extremely likely that the package is simply not installable and a bug report against that package should be filed. The following information may help to resolve the situation: The following packages have unmet dependencies: libmagick9-dev: Depends: libjpeg62-dev but it is not going to be installed Depends: libbz2-dev but it is not going to be installed Depends: libtiff4-dev but it is not going to be installed Depends: libwmf-dev (>= 0.2.7-1) but it is not going to be installed Depends: libz-dev Depends: libpng12-dev but it is not going to be installed Depends: libfreetype6-dev but it is not going to be installed Depends: libexif-dev but it is not going to be installed Depends: libdjvulibre-dev but it is not going to be installed Depends: librsvg2-dev but it is not going to be installed Depends: libgraphviz-dev but it is not going to be installed E: Broken packages I don't know what to do to fix this? EDIT 1: I tried sudo apt-get install librmagick-ruby and it worked fine but then I needed to install the fleximage gem gem1.8 install fleximage and I got the following error message Building native extensions. This could take a while... ERROR: Error installing fleximage: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for Ruby version >= 1.8.5... yes checking for cc... yes checking for Magick-config... no Can't install RMagick 2.12.2. Can't find Magick-config in /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/var/lib/gems/1.8/bin *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/rmagick-2.12.2 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/rmagick-2.12.2/ext/RMagick/gem_make.out

    Read the article

  • .htaccess template, suggestions needed

    - by purpler
    # Defaults AddDefaultCharset UTF-8 DefaultLanguage en-US FileETag None Header unset ETag ServerSignature Off SetEnv TZ Europe/Belgrade # Rewrites Options +FollowSymLinks RewriteEngine On RewriteBase / # Redirect to WWW RewriteCond %{HTTP_HOST} ^serpentineseo.com RewriteRule (.*) http://www.serpentineseo.com/$1 [R=301,L] # Redirect index to root RewriteCond %{THE_REQUEST} ^[A-Z]{3,9}\ /.*index\.html\ HTTP/ RewriteRule ^(.*)index\.html$ /$1 [R=301,L] # Cache media files: ExpiresActive On ExpiresDefault A0 # Month <filesMatch "\.(gif|jpg|jpeg|png|ico|swf|js)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> # Week <FilesMatch "\.(css|pdf)$"> Header set Cache-Control "max-age=604800" </FilesMatch> # 10 Min <FilesMatch "\.(html|htm|txt)$"> Header set Cache-Control "max-age=600" </FilesMatch> # Do not cache <FilesMatch "\.(pl|php|cgi|spl|scgi|fcgi)$"> Header unset Cache-Control </FilesMatch> # Compress output <IfModule mod_deflate.c> <FilesMatch "\.(html|js|css)$"> SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error Documents ErrorDocument 206 /error/206.html ErrorDocument 401 /error/401.html ErrorDocument 403 /error/403.html ErrorDocument 404 /error/404.html ErrorDocument 500 /error/500.html # Prevent hotlinking RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://(www\.)?serpentineseo.com/.*$ [NC] RewriteRule \.(gif|jpg|png)$ http://www.serpentineseo.com/images/angryman.png [R,L] # Prevent offline browsers RewriteCond %{HTTP_USER_AGENT} ^BlackWidow [OR] RewriteCond %{HTTP_USER_AGENT} ^Bot\ mailto:[email protected] [OR] RewriteCond %{HTTP_USER_AGENT} ^ChinaClaw [OR] RewriteCond %{HTTP_USER_AGENT} ^Custo [OR] RewriteCond %{HTTP_USER_AGENT} ^DISCo [OR] RewriteCond %{HTTP_USER_AGENT} ^Download\ Demon [OR] RewriteCond %{HTTP_USER_AGENT} ^eCatch [OR] RewriteCond %{HTTP_USER_AGENT} ^EirGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailSiphon [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailWolf [OR] RewriteCond %{HTTP_USER_AGENT} ^Express\ WebPictures [OR] RewriteCond %{HTTP_USER_AGENT} ^ExtractorPro [OR] RewriteCond %{HTTP_USER_AGENT} ^EyeNetIE [OR] RewriteCond %{HTTP_USER_AGENT} ^FlashGet [OR] RewriteCond %{HTTP_USER_AGENT} ^GetRight [OR] RewriteCond %{HTTP_USER_AGENT} ^GetWeb! [OR] RewriteCond %{HTTP_USER_AGENT} ^Go!Zilla [OR] RewriteCond %{HTTP_USER_AGENT} ^Go-Ahead-Got-It [OR] RewriteCond %{HTTP_USER_AGENT} ^GrabNet [OR] RewriteCond %{HTTP_USER_AGENT} ^Grafula [OR] RewriteCond %{HTTP_USER_AGENT} ^HMView [OR] RewriteCond %{HTTP_USER_AGENT} HTTrack [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Stripper [OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} Indy\ Library [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^InterGET [OR] RewriteCond %{HTTP_USER_AGENT} ^Internet\ Ninja [OR] RewriteCond %{HTTP_USER_AGENT} ^JetCar [OR] RewriteCond %{HTTP_USER_AGENT} ^JOC\ Web\ Spider [OR] RewriteCond %{HTTP_USER_AGENT} ^larbin [OR] RewriteCond %{HTTP_USER_AGENT} ^LeechFTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Mass\ Downloader [OR] RewriteCond %{HTTP_USER_AGENT} ^MIDown\ tool [OR] RewriteCond %{HTTP_USER_AGENT} ^Mister\ PiX [OR] RewriteCond %{HTTP_USER_AGENT} ^Navroad [OR] RewriteCond %{HTTP_USER_AGENT} ^NearSite [OR] RewriteCond %{HTTP_USER_AGENT} ^NetAnts [OR] RewriteCond %{HTTP_USER_AGENT} ^NetSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Net\ Vampire [OR] RewriteCond %{HTTP_USER_AGENT} ^NetZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Octopus [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Explorer [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Navigator [OR] RewriteCond %{HTTP_USER_AGENT} ^PageGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^Papa\ Foto [OR] RewriteCond %{HTTP_USER_AGENT} ^pavuk [OR] RewriteCond %{HTTP_USER_AGENT} ^pcBrowser [OR] RewriteCond %{HTTP_USER_AGENT} ^RealDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^ReGet [OR] RewriteCond %{HTTP_USER_AGENT} ^SiteSnagger [OR] RewriteCond %{HTTP_USER_AGENT} ^SmartDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperBot [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperHTTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Surfbot [OR] RewriteCond %{HTTP_USER_AGENT} ^tAkeOut [OR] RewriteCond %{HTTP_USER_AGENT} ^Teleport\ Pro [OR] RewriteCond %{HTTP_USER_AGENT} ^VoidEYE [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Image\ Collector [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebAuto [OR] RewriteCond %{HTTP_USER_AGENT} ^WebCopier [OR] RewriteCond %{HTTP_USER_AGENT} ^WebFetch [OR] RewriteCond %{HTTP_USER_AGENT} ^WebGo\ IS [OR] RewriteCond %{HTTP_USER_AGENT} ^WebLeacher [OR] RewriteCond %{HTTP_USER_AGENT} ^WebReaper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebSauger [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ eXtractor [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ Quester [OR] RewriteCond %{HTTP_USER_AGENT} ^WebStripper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebWhacker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Wget [OR] RewriteCond %{HTTP_USER_AGENT} ^Widow [OR] RewriteCond %{HTTP_USER_AGENT} ^WWWOFFLE [OR] RewriteCond %{HTTP_USER_AGENT} ^Xaldon\ WebSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Zeus RewriteRule ^.*$ http://www.google.com [R,L] # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Deny access to sensitive files <FilesMatch "\.(htaccess|psd|log)$"> Order Allow,Deny Deny from all </FilesMatch>

    Read the article

  • Varnish 503 Guru Mediation errors with pfsense and healthy apache

    - by Fammy
    We are running a pfsense firewall / load balancer with varnish as service, In front of Fedora linux webservers running apache. We are getting intermittent 503 guru mediation errors. We are a bit stuck scratching our heads because it is not easily repeatable. The timeouts are set to 30s (connect and first byte) but yet the 503 page will show instantly, not after 30s. Then if you refresh immediately it may very well work instantly and sometimes for a 100 refreshes. The load average on the web servers is < 1, the DB server is < 3 (all servers (web, db, pfsense/varnish) are physical rather than VM. I would have thought if the timeouts were being hit then the 503 page would only appear after 30s am I mistaken? Also when an error happens there does not appear to be any corresponding error in apache's log files. This seems to affect pages as well as images, so it is possible to have the page load fine, and for 9/10 images on the page to be fine but 1 not work An example of the varnish debug is below. It says no backend connection but I can't figure out why, if the load was high on apache I could understand it being flaky The machines are on the same gig ethernet lan 21 ReqStart c *IP-REMOVED* 33418 1274368062 21 RxRequest c GET 21 RxURL c /fashion/ 21 RxProtocol c HTTP/1.1 21 RxHeader c User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.0.5) Gecko/2008121622 Fedora/3.0.5-1.fc10 Firefox/3.0.5 21 RxHeader c Host: *ourdomain.com* 21 RxHeader c Accept: */* 21 RxHeader c Accept-Encoding: deflate, gzip 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error restart 21 VCL_call c recv lookup 21 VCL_call c hash 21 Hash c /fashion/ 21 Hash c *ourdomain.com* 21 VCL_return c hash 21 VCL_call c miss fetch 21 FetchError c no backend connection 21 VCL_call c error deliver 21 VCL_call c deliver deliver 21 TxProtocol c HTTP/1.1 21 TxStatus c 503 21 TxResponse c Service Unavailable 21 TxHeader c Server: Varnish 21 TxHeader c Content-Type: text/html; charset=utf-8 21 TxHeader c Content-Length: 384 21 TxHeader c Accept-Ranges: bytes 21 TxHeader c Date: Wed, 11 Apr 2012 10:36:17 GMT 21 TxHeader c X-Varnish: 1274368062 21 TxHeader c Age: 0 21 TxHeader c Via: 1.1 varnish 21 TxHeader c Connection: close 21 TxHeader c X-Cache: MISS 21 Length c 384 21 ReqEnd c 1274368062 1334140577.449995041 1334140577.450334787 1.794108152 0.000282764 0.000056982

    Read the article

< Previous Page | 639 640 641 642 643 644 645 646 647 648 649 650  | Next Page >