Search Results

Search found 17317 results on 693 pages for 'memory upgrade'.

Page 644/693 | < Previous Page | 640 641 642 643 644 645 646 647 648 649 650 651  | Next Page >

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• Encoding multiple video streams with a single avconv invocation

  - by automatthias

  I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

  Read the article

• What presentation software suits my needs?

  - by claws

  Background: I'm teaching biology to 12th grade students. The syllabus I'm teaching is huge. I mean literally, very huge. There is a lot for students to remember. There are no less than 1000 facts (weird names, dates etc) for students to remember. They'll have to remember all of them, they don't have a choice. The notes I compiled for their learning itself is upto 80 printed pages(Just the bullet outline & facts). That's just one chapter. We have 34 chapters. Also my students are very hardworking, they study upto 8-10hrs per day (Yeah! we are from India :). So, I want to ensure maximum retaining by the students at each and every stage (Teaching & Learning). I'm trying to as many memory training techniques as possible. I'm trying to incorporate, mnemonics, strong visual aids (pictures, 3D-animations, real videos etc.), spaced repetition etc. I think MS powerpoint is not suitable for my needs: There are about 200 slides per chapter. Its very easy for students to get lost while teaching. Because the problem with powerpoint is that it gives facts (as bullets) but it doesn't exploit the association & organization (Concept Map) of the content, which helps students learn quickly. I found an amazing software called XMind. You can see the screenshot here. Problem is that it is not as powerpoint in terms of powerpoint. This software can be used for just for concept maps. In the above screenshot, each topic occupies a single slide. I have an Image/picture(Detailed huge picture) and about 5-10 bullet points and probably a video or an animation of somethings. And this XMind is not good at presenting, in terms that it doesn't allow me to set what to present after what. I want to present a top down view, with a slide for each topic. PS: I Don't like prezi.com. I tried but it simply is too confusing for my students. It zooms here and there. I didn't tried it but I've seen few presentations.

  Read the article

• How to get more information from the system crash

  - by viraptor

  I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

  Read the article

• SQL2008R2 install issues on windows 7 - unable to install setup support files?

  - by Liam

  I am trying to install the above but am getting the following errors when its attempting to install the setup support files, This is the first error that occurs during installation of the setup support files TITLE: Microsoft SQL Server 2008 R2 Setup ------------------------------ The following error has occurred: The installer has encountered an unexpected error. The error code is 2337. Could not close file: Microsoft.SqlServer.GridControl.dll GetLastError: 0. Click 'Retry' to retry the failed action, or click 'Cancel' to cancel this action and continue setup. For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.50.1600.1&EvtType=0xDF039760%25401201%25401 This is the second error that occurs after clicking continue in the installer after the first error is generated TITLE: Microsoft SQL Server 2008 R2 Setup ------------------------------ The following error has occurred: SQL Server Setup has encountered an error when running a Windows Installer file. Windows Installer error message: The Windows Installer Service could not be accessed. This can occur if the Windows Installer is not correctly installed. Contact your support personnel for assistance. Windows Installer file: C:\Users\watto_uk\Desktop\In-Digital\Software\Microsoft\SQL Server 2008 R2\1033_ENU_LP\x64\setup\sqlsupport_msi\SqlSupport.msi Windows Installer log file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20110713_205508\SqlSupport_Cpu64_1_ComponentUpdate.log Click 'Retry' to retry the failed action, or click 'Cancel' to cancel this action and continue setup. For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.50.1600.1&EvtType=0xDC80C325 These errors are generated from an ISO package downloaded from Microsoft. I have also tried using the web platform installer to install the express version instead but the SQL Server Installation fails with that also. The management studio installs fine but not the server. I have checked to make sure that the Windows Installer is started and it is. Cant seem to find an answer for this anywhere as all previous reported issues appear to be related to XP. I did have the express edition installed on the machine previously but uninstalled it to upgrade to the full version, I wish I hadn't now. Can anyone kindly offer any advice or point me in the right direction to stop me going insane with this? Any advice will be appreciated. Update======================= After digging a bit deeper ive located details of the error from the setup log file, i can also upload the log file if required. MSI (s) (E8:28) [23:35:18:705]: Assembly Error:The module '%1' was expected to contain an assembly manifest. MSI (s) (E8:28) [23:35:18:705]: Note: 1: 1935 2: 3: 0x80131018 4: IStream 5: Commit 6: MSI (s) (E8:28) [23:35:18:705]: Note: 1: 2337 2: 0 3: Microsoft.SqlServer.GridControl.dll MSI (s) (E8:28) [23:35:22:869]: Product: Microsoft SQL Server 2008 R2 Setup (English) -- Error 2337. The installer has encountered an unexpected error. The error code is 2337. Could not close file: Microsoft.SqlServer.GridControl.dll GetLastError: 0. MSI (s) (E8:28) [23:35:22:916]: Internal Exception during install operation: 0xc0000005 at 0x000007FEE908A23E. MSI (s) (E8:28) [23:35:22:916]: WER report disabled for silent install. MSI (s) (E8:28) [23:35:22:932]: Internal MSI error. Installer terminated prematurely. Error 2337. The installer has encountered an unexpected error. The error code is 2337. Could not close file: Microsoft.SqlServer.GridControl.dll GetLastError: 0. MSI (s) (E8:28) [23:35:22:932]: MainEngineThread is returning 1603 MSI (s) (E8:58) [23:35:22:932]: RESTART MANAGER: Session closed. Installer stopped prematurely. MSI (c) (0C:14) [23:35:22:947]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1 MSI (c) (0C:14) [23:35:22:947]: MainEngineThread is returning 1601 === Verbose logging stopped: 13/07/2011 23:35:22 ===

  Read the article

• Launchd item no longer firing in Snow Leopard

  - by ridogi

  A launchd item that was working in 10.5 is no longer working after my upgrade to 10.6. I am running 10.6.2 and I have recreated the launchd item and given it a new name and that one doesn't run either. I have found a link of people with the same problem on google groups but none of the advice in that link helps. My launchd item is not listed in /private/var/db/launchd.db/com.apple.launchd/overrides.plist or in any of the overrides.plist files in the subdirectories of /private/var/db/launchd.db/ I have also tried to set this up as both a user agent and a user daemon. My launchd item simply runs a shell script, which I have no problem launching manually. <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>com.eric.tmnotify.launchd</string> <key>ProgramArguments</key> <array> <string>/<path_to>/tmnotify.sh</string> </array> <key>StartInterval</key> <integer>3600</integer> </dict> </plist> I have tried to load it by overriding the disabled key (even though it is not disabled in any of the overrides.plist files) with both: sudo launchctl load -F /Users/eric/Library/LaunchAgents/com.eric.tmnotify.launchd.plist sudo launchctl load -w /Users/eric/Library/LaunchAgents/com.eric.tmnotify.launchd.plist and after running either of them I can see that it is running by using sudo launchctl list but the shell script never fires. Edit: I have also put this in the formerly blank file at /private/var/db/launchd.db/com.apple.launchd.peruser.501/overrides.plist : <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>com.eric.tmnotify.launchd</key> <dict> <key>Disabled</key> <false/> </dict> </dict> </plist> I also tried inserting this alphabetically: <key>com.eric.tmnotify.launchd</key> <dict> <key>Disabled</key> <false/> </dict> into the file /private/var/db/launchd.db/com.apple.launchd/overrides.plist but still no dice.

  Read the article

• Ubuntu Server 12.04 CPU Load

  - by zertux

  I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

  Read the article

• Suspicious process running under user named

  - by Amit

  I get a lot of emails reporting this and I want this issue to auto correct itself. These process are run by my server and are a result of updates, session deletion and other legitimate session handling reported as false positives. Here's a sample report: Time: Sat Oct 20 00:00:03 2012 -0400 PID: 20077 Account: named Uptime: 326117 seconds Executable: /usr/sbin/nsd\00507d27e9\0053\00\00\00\00\00 (deleted) The file system shows this process is running an executable file that has been deleted. This typically happens when the original file has been replaced by a new file when the application is updated. To prevent this being reported again, restart the process that runs this excecutable file. See csf.conf and the PT_DELETED text for more information about the security implications of processes running deleted executable files. Command Line (often faked in exploits): /usr/sbin/nsd -c /etc/nsd/nsd.conf Network connections by the process (if any): udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 udp: 127.0.0.1:53 -> 0.0.0.0:0 udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: 127.0.0.1:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 Files open by the process (if any): /dev/null /dev/null /dev/null Memory maps by the process (if any): 0045e000-00479000 r-xp 00000000 fd:00 2582025 /lib/ld-2.5.so 00479000-0047a000 r--p 0001a000 fd:00 2582025 /lib/ld-2.5.so 0047a000-0047b000 rw-p 0001b000 fd:00 2582025 /lib/ld-2.5.so 0047d000-005d5000 r-xp 00000000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d5000-005d7000 r--p 00157000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d7000-005d8000 rw-p 00159000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d8000-005db000 rw-p 005d8000 00:00 0 005dd000-005e0000 r-xp 00000000 fd:00 2582087 /lib/libdl-2.5.so 005e0000-005e1000 r--p 00002000 fd:00 2582087 /lib/libdl-2.5.so 005e1000-005e2000 rw-p 00003000 fd:00 2582087 /lib/libdl-2.5.so 0062b000-0063d000 r-xp 00000000 fd:00 2582079 /lib/libz.so.1.2.3 0063d000-0063e000 rw-p 00011000 fd:00 2582079 /lib/libz.so.1.2.3 00855000-0085f000 r-xp 00000000 fd:00 2582022 /lib/libnss_files-2.5.so 0085f000-00860000 r--p 00009000 fd:00 2582022 /lib/libnss_files-2.5.so 00860000-00861000 rw-p 0000a000 fd:00 2582022 /lib/libnss_files-2.5.so 00ac0000-00bea000 r-xp 00000000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bea000-00bfe000 rw-p 00129000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bfe000-00c01000 rw-p 00bfe000 00:00 0 00e68000-00e69000 r-xp 00e68000 00:00 0 [vdso] 08048000-08074000 r-xp 00000000 fd:00 927261 /usr/sbin/nsd 08074000-08079000 rw-p 0002b000 fd:00 927261 /usr/sbin/nsd 08079000-0808c000 rw-p 08079000 00:00 0 08a20000-08a67000 rw-p 08a20000 00:00 0 b7f8d000-b7ff2000 rw-p b7f8d000 00:00 0 b7ffd000-b7ffe000 rw-p b7ffd000 00:00 0 bfa6d000-bfa91000 rw-p bffda000 00:00 0 [stack] Would /etc/nsd/restart or kill -1 20077 solve the problem?

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• Very slow printing from print server

  - by evolvd

  Print server is a VM on Xen The VM is Windows 2003 32bit. During the issue the VM is not being taxed in anyway, cpu, memory, hd read/write, and network speed is all good. The problem that I see is the transfer of the print file from the print server to the printer. The 80Mb file is transferred from the client to the print server in about 2 minutes but then it takes about 2 hours for that file to be sent to the printer. I can't figure out why this would just start to happen. The printer is rebooted every evening and is just used for one large print job in the morning. The server has been rebooted with no effect I changed the spool option to send the entire spool to the server before printing starts and it had no effect. This printer problem did happen to come about after some changes to the Xen environment. The Xen servers changed from using HBA NIC cards to software iscsi and a new switch was put in. I don't think this is related to the problem since all the speeds on the VMs are better now. The changed happened on Saturday and the first print to this printer happened on Monday morning. I'm just putting that out there but like I said I don't think it is related but I don't want to rule it out. At this point I don't have many other options besides the physical layer. I can switch out network cable that goes to the printer and I might be able to print the same job to another printer. I wont be able to test those things out till this afternoon though. Any other ideas or test I could do to try to find the reason for the slow speed? I forgot to say that this is only happening when printing to this one printer. ===Update=== I found out that there are a few printers that currently have this issue, not just the one. There are over 30 printers on the server though so I know it's not happening to all of them. I printed a large pdf doc from the server and it was able to print at the normal speed. If the machine sends the large print request it gets to the server fine but then slow to get from the server to the printer. If sent directly from the printer it gets to the printer at the normal speed. The question now is why is there a speed difference when it comes from the machine and why would it start now?

  Read the article

• Windows 7, weird/annoying explorer problem

  - by Shiki

  First of all, I'm asking the moderators if you could summarize my problem in the Title and modify it according to that. Thanks in advance and sorry, my english is not that good. The problem. It happened on two of my machines already. Once it happens there are many problems with explorer. I'll try to describe at precisely I just can. So. Basically when you create a new folder, you have to hit the enter key TWICE because first it'll throw an error that "there is no such file..". Okay. Then if you try to delete some, this happens also. Renaming is the same. Here is an example. I tried adding a "2" to the end of the folder name, hit enter and got this. Here I can press cancel, nothing happens. If I press retry, the popup disappears and it'll finally change the folder name. I can't come up with anything for this. Using BitDefender (registered, full protection), Windows 7 x86 Ultimate retail (boxed, english version). The other PC had the same anti-virus protection , but it have a Windows 7 x64. Both systems are activated, updated totally. I don't remember installing any new stuff on the PCs. All the stuff on the PCs are legal, no cracked / any other software present. It just happened, so to say. Already reinstalled the other PC because I thought * I * messed up something and its just something FUBAR. However, I dont want to reinstall my laptop also. Any ideas are welcome. (Today I had a strange bug. Windows Explorer had 1.0+gb memory usage with 100% cpu. Killed it, launched a new explorer.exe and thats all. Nothing changed, but it may worth a try. The other PC did NOT have this problem, ever.) Isn't there a registry fix for this or something? :/

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• How to connect FreeBSD Jail to network

  - by jgtumusiime

  So recently I successfully installed and configured a freebsd jail and I would like to install software within my jail but I cannot connect to the network. I'm trying to setup an apache+php+mysql installation within the jail and have the webserver accessible by users. Here is my rc.conf for the jail. ... jail_enable="YES" # Set to NO to disable starting of any jails jail_list="mambo2" # Space separated list of names of jails jail_mambo2_rootdir="/usr/jails/j01" # jail's root directory jail_mambo2_hostname="mambo2.ug" # jail's hostname jail_mambo2_ip="192.168.100.174" # jail's IP address jail_mambo2_devfs_enable="YES" # mount devfs in the jail jail_mambo2_devfs_ruleset="mambo2_ruleset" # devfs ruleset to apply to jail here is my jail ifconfig output mambo2# ifconfig rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:c1:28:00:48:db media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> metric 0 mtu 1500 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 mambo2# It does not show the IP address I configured within /etc/rc.conf. But, when I list the running jails, it shows the right IP address. Here is a list of jails running [root@mambo /usr/home/jtumusiime]# jls JID IP Address Hostname Path 5 192.168.100.174 mambo2.ug /usr/jails/j01 I also created a /etc/resolv.conf for nameservers. This was not in existence so I'm not quite sure if it is necessary? mambo2# cat /etc/resolv.conf nameserver 192.168.100.251 nameserver 8.8.8.8 mambo2# my host has 4 ip addresses, 3 public and one private: 192.168.100.173 I tried creating a jail using ezjail and this does not work out. [root@mambo /usr/src]# ezjail-admin update -p -i Error: Cannot find your copy of the FreeBSD source tree in . Consider using 'ezjail-admin install' to create the base jail from an ftp server. [root@mambo /usr/src]# I have an updated copy of freebsd 7.1 source tree from SVN in /usr/src/ [root@mambo /usr/src]# svn info Path: . URL: http://svn.freebsd.org/base/release/7.1.0 Repository Root: http://svn.freebsd.org/base Repository UUID: ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 243371 Node Kind: directory Schedule: normal Last Changed Author: kensmith Last Changed Rev: 186660 Last Changed Date: 2009-01-01 01:57:14 +0300 (Thu, 01 Jan 2009) [root@mambo /usr/src]# and I did #make buildworld while building the first jail i.e mambo2 Here is an excerpt of ouput of ezjail-admin install ... 221 Goodbye. Trying 193.162.146.4... Connected to ftp.freebsd.org. 220 ftp.beastie.tdk.net FTP server (Version 6.00LS) ready. 331 Guest login ok, send your email address as password. 230 Guest login ok, access restrictions apply. Remote system type is UNIX. Using binary mode to transfer files. 200 Type set to I. 550 pub/FreeBSD-Archive/old-releases/i386/7.1-RELEASE/base: No such file or directory. 221 Goodbye. Could not fetch base from ftp.freebsd.org. Maybe your release (7.1-RELEASE) is specified incorrectly or the host ftp.freebsd.org does not provide that release build. Use the -r option to specify an existing release or the -h option to specify an alternative ftp server. Querying your ftp-server... The ftp server you specified (ftp.freebsd.org) seems to provide the following builds: Trying 193.162.146.4... total 10 drwxrwxr-x 13 1006 1006 512 Feb 20 2011 8.2-RELEASE drwxrwxr-x 13 1006 1006 512 Apr 10 2012 8.3-RELEASE lrwxr-xr-x 1 1006 1006 16 Jan 7 2012 9.0-RELEASE -> i386/9.0-RELEASE drwxrwxr-x 7 1006 1006 1024 Feb 19 2012 ISO-IMAGES -rw-rw-r-- 1 1006 1006 637 Nov 23 2005 README.TXT drwxrwxr-x 5 1006 1006 512 Nov 2 02:59 i386 I do not want to upgrade my freebsd installation. I have googled around; but all in vail. Thank you

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• graphic error on console

  - by Christian Elsner

  I have Linux on an embedded system. There is no graphic system, but I still have graphic errors. For example, if I type: ifconfig eth2 hw ether 00:0e:8c:d0:59:d2 I see: ifconfig eth hw ether 00:0e:8:2:2 If I type Enter, it accepts the command I typed, so it's just a matter of displaying. Everything is fine, when I log in via SSH. Anyone any ideas, what could be the cause or where to look at? Output of lspci: 00:00.0 Host bridge: Intel Corporation 3100 Chipset Memory I/O Controller Hub 00:00.1 Unassigned class [ff00]: Intel Corporation 3100 DRAM Controller Error Reporting Registers 00:01.0 System peripheral: Intel Corporation 3100 Chipset Enhanced DMA Controller 00:02.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A 00:03.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A1 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 01) 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c9) 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 01) 02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection 03:01.0 Network controller: Siemens Nixdorf AG Device 4003 (rev 02) 03:01.1 Unassigned class [ff00]: Siemens Nixdorf AG Device 4003 (rev 02) 03:02.0 Ethernet controller: Siemens Nixdorf AG Device 4047 (rev 01) 03:03.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 03:04.0 Unassigned class [ff00]: Siemens Nixdorf AG Device 4057 (rev 01) 04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 05:00.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 44) 06:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 07:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) 07:01.0 USB Controller: NEC Corporation USB (rev 43) 07:01.1 USB Controller: NEC Corporation USB (rev 43) 07:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04) The whole thing is running on an Intel Core 2 Duo U2500

  Read the article

• Routing all data through an VPN tunnel with ppp

  - by Oliver

  I'm trying to create a VPN tunnel that forwards all data from the local machine to the VPN server. I'm using ppp-2.4.5 for this with the following configuration: pty "pptp <VPNServer> --nolaunchpppd" name <my login name> remotename PPTP usepeerdns require-mppe-128 file /etc/ppp/options.pptp persist maxfail 0 holdoff 5 I have a script in if-up.d with the following content: route del default eth0 route add default dev ppp0 Before starting the VPN tunnel my routing looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 2 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 After starting the tunnel (via pon) it looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 12.34.56.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 Now the problem is, that the VPN tunnel seems to be looped into itself. If I run ifconfig after a few seconds without any traffic: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.10 netmask 255.255.0.0 broadcast 192.168.255.255 ether 00:01:2e:2f:ff:35 txqueuelen 1000 (Ethernet) RX packets 39931 bytes 6784614 (6.4 MiB) RX errors 0 dropped 90 overruns 0 frame 0 TX packets 34980 bytes 7633181 (7.2 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xfbdc0000-fbde0000 ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1496 inet 12.34.56.78 netmask 255.255.255.255 destination 12.34.56.1 ppp txqueuelen 3 (Point-to-Point Protocol) RX packets 7 bytes 94 (94.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 782863 bytes 349257986 (333.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 It states that already over 300 MiB have been send, ppp0 is only online since a few seconds and the connection isn't working anyway. Can someone please help me to fix the routing table, so that the traffic from ppp0 is not send again through ppp0 but instead goes to the remote server?

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• 2xAMD Opteron 6128 with libvirt, Physical CPU 13 doesn't exist

  - by yak

  I need help with libvirt(?) problem. Server specs: ProLiant DL165 G7 2x AMD Opteron(tm) Processor 6128 System: Debian GNU/Linux testing (wheezy) 3.2.0-3-amd64 libvirt 0.9.12-5 kvm 1:1.1.2+dfsg-2 $ grep processor /proc/cpuinfo | wc -l 16 $ virsh nodeinfo setlocale: No such file or directory CPU model: x86_64 CPU(s): 16 CPU frequency: 800 MHz CPU socket(s): 2 Core(s) per socket: 4 Thread(s) per core: 1 NUMA cell(s): 1 Memory size: 66114200 KiB $ virsh capabilities .. <topology> <cells num='4'> <cell id='0'> <cpus num='4'> <cpu id='0'/> <cpu id='1'/> <cpu id='2'/> <cpu id='3'/> </cpus> </cell> <cell id='1'> <cpus num='4'> <cpu id='4'/> <cpu id='5'/> <cpu id='6'/> <cpu id='7'/> </cpus> </cell> <cell id='2'> <cpus num='4'> <cpu id='12'/> <cpu id='13'/> <cpu id='14'/> <cpu id='15'/> </cpus> </cell> <cell id='3'> <cpus num='4'> <cpu id='8'/> <cpu id='9'/> <cpu id='10'/> <cpu id='11'/> </cpus> </cell> </cells> </topology> .. $ virsh vcpupin vm 0 13,12,11,10,9,8,7,6,5 error: Physical CPU 13 doesn't exist. error: cpulist: Invalid format. Question? Why my VM Guests use only first 8 CPUs and next 8 are idling? $ for host in virsh list | awk '{print $2}'; do virsh vcpuinfo $host; done | grep ^CPU: | sort | uniq CPU: 0 CPU: 1 CPU: 2 CPU: 3 CPU: 4 CPU: 5 CPU: 6 CPU: 7 Any ideas how to change it?

  Read the article

• amazon ec2 ubuntu with gitlab and nginx - cant load?

  - by thebluefox

  Ok, so I've spooled up an Amazon EC2 server running Ubuntu, and then followed the instructions below to install GitLab; http://doc.gitlab.com/ce/install/installation.html The only step I've not been able to complete is running the following check on the status; sudo -u git -H bundle exec rake gitlab:check RAILS_ENV=production I get the following error; rake aborted! Errno::ENOMEM: Cannot allocate memory - whoami Which I presume is becuase my EC2 is just running a free tier setup, so isn't that well spec'd. Regardless, I've been trying to access this through my browser. I've set up the elastic IP and pointed my domain at it (for the purpose of this, lets say its git.mydom.co.uk). Doing a whois on this domain shows me its pointing to the right place. For some reason though, I get the "Oops, Chrome could not connect to git.mydom.co.uk". Now - for a period of time I was getting the Nginx holding page (telling me I still needed to perform configuration). This though disappeared after removing the default file from /etc/nginx/sites-enabled/ (after reading this could be issue on a troubleshooting page). Since then, I've had nothing, even when I symlinked the file back in from /sites-available. I've tried changing the owner of the git.mydom.co.uk file sat inside /sites-enabled and /sites-available to www-data, as suggested here, but I could only change the permission of the file in /sites-available, and not the symlinked one in /sites-enabled. The content of this file is as follows; upstream gitlab { server unix:/home/git/gitlab/tmp/sockets/gitlab.socket; } server { listen *:80 default_server; # e.g., listen 192.168.1.1:80; In most cases *:80 is a good idea server_name git.mydom.co.uk; # e.g., server_name source.example.com; server_tokens off; # don't show the version number, a security best practice root /home/git/gitlab/public; # Increase this if you want to upload large attachments # Or if you want to accept large git objects over http client_max_body_size 20m; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } All the paths mentioned in here look ok...I'm about at the end of my knowledge now!

  Read the article

• Varnish server in front of nginx server with multiple virtualhosts

  - by Garreth 00

  I have tried to search for a solution for this, but can't find any documentation/tips on my specific setup. My setup: Backendserver: ngnix: 2 different websites (2 top domains) in virtualenv, running gunicorn/python/django Backendserver hardware(VPS) 2gb ram, 8 CPU Databaseserver: postgresql - pg_bouncer Backendserver hardware (VPS) 1gb ram, 8 CPU Varnishserver: only running varnish Varnishserver hardware (VPS) 1gb ram, 8 CPU I'm trying to set up a varnish server to handle rare spike in traffic (20 000 unique req/s) The spike happens when a tv program mention one of the sites. What do I need to do, to make the varnish server cache both sites/domains on my backendserver? My /etc/varnish/default.vcl : backend django_backend { .host = "local.backendserver.com"; .port = "8080"; } My /usr/local/nginx/site-avaible/domain1.com upstream gunicorn_domain1 { server unix:/home/<USER>/.virtualenvs/<DOMAIN1>/<APP1>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain1.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80 default_server; listen 8080; client_max_body_size 4G; server_name www.domain1.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain1; break; } } } My /usr/local/nginx/site-avaible/domain2.com upstream gunicorn_domain2 { server unix:/home/<USER>/.virtualenvs/<DOMAIN2>/<APP2>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain2.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80; listen 8080; client_max_body_size 4G; server_name www.domain2.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain2; break; } } } Right now, If I try the Ip of the varnishserver I only get served domain1.com. Would everything be correct if I change the DNS of the two domain to point to the varnishserver, or is there extra setup before it would work? Question 2: Do I need a dedicated server for varnish, or could I just install varnish on my backendserver, or would the server run out of memory quick?

  Read the article

< Previous Page | 640 641 642 643 644 645 646 647 648 649 650 651  | Next Page >