Search Results

Search found 29426 results on 1178 pages for 'user99572 is fine'.

Page 65/1178 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• Windows Home Server Passwords Do Not Match

  - by Ben Fulton

  I have a Windows Home Server that chunks along just fine most of the time. I've never bothered to put it on a UPS and so it's vulnerable to power outages that happen a few times a year. This most recent time, it came back and seemed to be fine, but whenever I try to access a shared folder I get "Passwords do not match". They matched before the power went out, and I couldn't update the WHS password since I apparently didn't know the old one. How do I fix this? (I asked this on ServerFault and they recommended it be asked here instead)

  Read the article

• System has reached the maximum size allowed for the system part of the registry

  - by Bob Denny

  To be precise System has reached the maximum size allowed for the system part of the registry. Additional storage requests will be ignored. WinXP/64 running fine for 2 years (no /3Gb switch), just started happening. I used ntregopt and the problem went away at least temporarily. However, looking before and after in Windows\System32\Config I see that my System file was reduced only by 10% and is still 170+ Mb. According to my rather extensive research with Google, this is "huge" and should be more like 10-20Mb. The system runs fine. There is a System.bak that is only 11Mb and has the date when I ran ntregopt. That's what I know. Now my question: Is there anything I can do to reduce or rebuild the System registry hive given the above info?

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• Permissions needed to read event log messages remotely?

  - by Neolisk

  When running under a limited account, local event log messages are displaying fine, for remote computer I am getting this error: The description for Event ID ( xxxxx ) in Source ( yyyyy ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to retrieve this description; see Help and Support for details. The following information is part of the event: zzzzz. Same remote computer works fine under domain administrator. I am currently experimenting with just the Event Viewer, by using Run As. Original issue is a PowerShell script which does Get-EventLog. Are there any special permissions that need to be in place to able to read event log messages remotely? Supposedly there is a simple solution in Windows 2008 and higher, i.e. just add user to Event Log Readers group. Is there anything like that for Windows 2003?

  Read the article

• Monitor weirdness/flickering with new Viao PCG-3112L

  - by Rosarch

  I have a Sony VAIO PCG-3112L running Windows 7. It worked fine on one monitor, but now I'm using it with a 2 year old LG Flatron W2252TQ-TF. The colors are sorta off (although that might just be the monitor), but more annoyingly there are many horizontal flickering lines. It's more noticeable on non-white backgrounds. I tried rebooting the monitor, and reseting it to factory settings, but that didn't solve the issue. What could be the cause of this? The monitor works fine with an Asus netbook. I have checked that both ends of the VGA cable are plugged in between the Vaio and the monitor.

  Read the article

• Can't access LAN computers with SSH

  - by endolith

  I got a new Windows 7 machine, and was using VNC,SSH etc to connect to my Ubuntu machine, and it worked fine previously. Now it doesn't work if I use the machine's hostname or local IP, but if I use the DynDNS name, it works. I can also access it from my Android phone using the local hostname over SSH. If I try to connect with SSH to the hostname, it says "Host does not exist". VNC says "Failed to get server address". NX says "no address associated with name", and I don't see it in Windows' "Network" folder. I've rebooted everything. I've turned off Windows firewall. It was working fine a few days ago, but now it's not. How do I figure out what's blocking it?

  Read the article

• File corruption when copying different file on raid 1

  - by Stephan

  I have a RAID 1 configuration of 2 1TB drives on a Fedora 12 box. Most of what is stored there are video files that are numerical labeled. The problem I'm having is that I had one of the video files get corrupted. I copied a replacement from a backup and replaced the bad file and now it works fine. However, after doing this the next numbered file goes from 350MB to 200KB and all but about .5 second of video disappears. If I then replace that file it happens to the next one down the line. Ex: Replace corrupt file 1.avi and file 2.avi shrinks to 200KB. Replace now corrupted 2.avi and it works but 3.avi gets screwed up. I have run SMART tests on the drives and they report fine. Does anyone have any tests I can run to try to figure out what is going on? EDIT: It is a two disk software RAID 1 with an ext4 filesystem

  Read the article

• Outlook Prompting for password from Exchange server in domain environment

  - by jherlitz

  We are running exchange 2007 in a domain environment. We have mostly outlook 2003 clients, but in process of upgrading to outlook 07 over the next couple of weeks. Some users (both 03 & 07) are constantly getting prompted to enter their credentials. The 07 client I was working on this morning states "needs password" in the bottom right corner. It is also speratic, as it will work fine most days but not some other days. The user I was working with this morning, has been working fine. Now it just started up today. I have been googling this, and have found lot's of information, but nothing that has helped yet. A lot of the information out there is for outlook users using a external email account. Being they already logged into the domain, these users should not be prompted for their credentials. Any advice out there?

  Read the article

• fdisk -l only displays boot partition

  - by Franklin

  I have a SAN, and it's able to read and write to the 50TB RAID just fine, but when I run fdisk -l it only lists the boot partition of the SAN server, and doesn't display anything about the other partitions on the RAID. I've also tried using parted -l with the same result. Now when I type mount it shows that the partitions are mounted just fine. I've never seen this happen. The box is running Openfiler 2.3 (I know it's old, we're in the process of upgrading all our old equipment). We have another SAN that's configured almost identically, and it's able to display the partition info with either of the two commands I mentioned above.

  Read the article

• Why can't I share my printer on Windows 7?

  - by Edward Tanguay

  I have Windows 7 installed on two computers. I can share folders between them fine. However, I can't seem to share printers between them: when I right-click on the printer I expect to see "share printer" but there is no option for that. When I read about "share printers" in the Windows 7 help, it talks about this computer "not being able to connect to a home network", yet they seem to be connected fine (I can share files between them). Why can't I share printers between the computers if I can share files?

  Read the article

• Why does PsExec hang after successfully running a powershell script?

  - by Matt

  The script is fairly straight forward. Simply tries to start a bunch of windows services. Execution locally works fine when on the target machine. The script is actually executing fine as well when done via PsExec, it just never returns until I hit the "enter" key on my CMD prompt. This is a problem, because this is being called from TeamCity, and it makes the Agent hang waiting for PsExec to return. I've tried the following: Adding an exit and exit 0 at the end of the Powershell script Adding a < NUL to the end of the PsExec call, per the answer in this SF question Adding a > stdout redirect This is how I am actually calling psexec: psexec \\target -u domain\username -p password powershell c:\path\script.ps1 No matter what I do, it hangs until I the locally on the cmd prompt. After I hit enter, I get the message: powershell exited on target with error code 0.

  Read the article

• VMWare Workstation can't read CD/DVD drive

  - by Chris W

  A fresh install of VMWare Workstation 7 (7.1.1 build 282343) on Windows 7 64 bit. When I try to read a CD/DVD from a guest (either to install a fresh guest or to read a CD within an existing VM I get the following error: Cannot connect virtual device ide1:0 because no corresponding device is available on the host. I've tried fiddling with the IDE channels as well as tried SCSI with no joy. What am I missing? I can run ISOs fine but I don't want to have to convert everything to an ISO when I presume that this should just work fine.

  Read the article

• What permissions are needed to do an LDAP bind to an Active Directory Server

  - by DrStalker

  What permissions are needed to perform an LDAP bind to an active directory server? I have a central domain (call it MAIN) that has two-way trusts to domains in other forests (call then REMOTE and FARAWAY) Using MAIN\myaccount as the username and my password I can bind to REMOTE fine, but not to FARAWAY; I get an invalid credentials response 80090308: LdapErr: DSID-0C09030B, comment: AcceptSecurityContext error, data 525, v893 In all other ways the trusts seem to work fine. What permissions do I need to check to figure out why the bind is failing? My understanding is that anyone in AUTHENTICATED USERS should be able to bind to LDAP, but that only seems to hold true for some domaians and not others.

  Read the article

• Website loading until initial script finishes

  - by wardy277

  Hi, i have a highly used server (running plesk). I have some long scripts that take a while to process (huge mysql database). I have found then in 1 browser, i run the script and while it is loading i cannot view any other parts of the site until the script finishes, it seems that all the requests go off, but they don't get served until the initial script finishes. i thought this may be a server wide issue, but it is not. If i use another computer i can view the site fine, even on the same computer with a different browser i can navigate fine, while the script still loads. I think it much limit the number of requests per session. Is this correct? is there any way to configure this to allow for 2-3 other requests per session? It is really bad that when i am on the phone to a client, i have just run a long report, but cannot use the site or follow what they are saying until the page has loaded? Chris

  Read the article

• What the best way to recover from when your RAID H/W incorrectly thinks a disk is missing

  - by Software Monkey

  I have a Windows 7 system with an MSI motherboard (running the latest AMD BIOS) and two of my four disks (not the system boot disk) configured via the Mobo as RAID-1. After a normal system restart today, the RAID BIOS reports that one of the two drives has been disconnected or has failed. It's not really failed; via recovery tools I can verify that if I take the BIOS out of RAID mode. But I can find no way to re-add the second hard disk to the array and rebuild via the BIOS - the only option seems be to delete the array and recreate it, but I've done that once before and it blows away the disk. It's done this once before, however on a subsequent reboot after double-checking the drive cabling (but not changing anything) and it boot up fine. So I think the mobo RAID is a little bit flaky. At this point I would like to remove the RAID drivers, change to AHCI mode and switch over to using a Windows 7 dynamic mirror disk. But the RAID drivers seem somehow deeply bound into the Windows startup - I can't find anything like the good ol' safe-mode in Windows 7. If I boot from the Win 7 install disk in ACHI mode I can use recovery tools to log in to the Windows 7 installation, so the boot drive it seems fine with ACHI mode. Additionally, I can see all my other disks, run chkdsk on them and they seem to be fine. If I try to boot from the HDD in AHCI mode, it just reboots part way through, presumably because the RAID drivers load and conflict with the BIOS being set to AHCI. So: How do I strip the RAID drivers from my Win 7 installation? If I delete the RAID logical disk, will it really delete partitioning information, or is that just a poorly worded message when it says the data on the disk will be deleted? If I disconnect the 2 disks in a RAID array, then delete the logical disk array, and then reconnect and reboot still in RAID mode, will the disks simply revert to RAID single-disks like my other 2 and then maybe I can leave windows with RAID drivers by operate the disks as singles with 2 of them in a Windows dynamic disk mirrored setup? Does Windows 7 have anything like the Windows XP Repair Install, where it will reinstall the O/S binaries from CD, but leave apps and setup alone. I am really hoping I don't have to do a complete reinstall of Windows 7 - the last one, when I upgraded from XP, took me two days to get everything set up and installed.

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• IIS not listening over external network, all other traffic working

  - by Beuy

  Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

  Read the article

• Running .NET app from network share in Win 7?

  - by mlangille

  We have a .NET 1.1 application that we keep on a netowork share. We install the .NET Framerwork to the local PCs and also set the full trust via the following: %windir%\Microsoft.NET\Framework\v1.1.4322\caspol -pp off -cg LocalIntranet_Zone FullTrust This has worked fine on all PCs to date however now we have a few new PCs with Win7 and the process no longer is working. The app will run fine from a local drive in Win7 but running the networked copy results in a general exception error. Any ideas on how to get this to work under Win7?

  Read the article

• SED and Unicode Quotation Marks

  - by Jonathan Patt

  When testing against this string: “… so that’s that… ” The following should, but does not, match the opening quotation mark and following ellipsis and space: sed "s/\([“‘\"']…\) /\1/g" However, this correctly matches the second ellipsis and following space and closing quotation mark: sed "s/… \([”’\"'.!?]\)/…\1/g" If I split the first apart it works fine: sed -e "s/\(“…\) /\1/g" \ -e "s/\(‘…\) /\1/g" \ -e "s/\(\"…\) /\1/g" \ -e "s/\('…\) /\1/g" So why doesn't it work when it's grouped together? Especially when it works fine with the closing quotation marks.

  Read the article

• How to make PDF pages with U3D images print properly?

  - by David Thornley

  I'm creating some PDF files that have three-dimensional images (U3D) in them. When I bring them up in Acrobat, everything is fine until I try to print the file. If I've viewed a page, it prints fine, showing the U3D image as I last saw it. If I haven't viewed a page yet, the printout is blank. (I can demonstrate this right from the Print dialog, by previewing pages.) The only reference I've seen to printing U3D is in the PDF Standard, which says, basically, that this should work. It recommends "PV" or "PO" for the A key in the 3D activation dictionary, and I'm using libharu which uses "PV".

  Read the article

• Windows 2003 SMTP virtual server, why emails are not delivered?

  - by bardan

  Configured Windows 2003 as my email client, everything works fine with POP3 (i'm able to recieve emails), the problem is with SMTP and i can't figure out how to find where excatly this problem is, because email looks like it is sent, but recipients don't recieve anything... i had some problems with relying, but fixed everything, and now i configured outlook express on the same machine, trying to send emails and it looks everything fine, email goes to SENT folder, no errors, but recipients (tried several diffrent) don't revieve any letters... tried to test from the same machine with telnet like it described there http://support.microsoft.com/kb/153119 ant everything looks ok...

  Read the article

• Why is my Output distorted after encoding with Expression Encoder?

  - by WernerCD

  I'm a "n00b" when it comes to re-encoding files. I'm trying to re-encode an AVI into a silverlight container via Encoding Video using Expression Encoder 4.0. As you can see in the video, the left is the input and it looks/sounds fine. The right is the output and it... doesn't. I'm unsure of where to go from here. I'm not sure why the output is jacked up, since the input looks fine. Input Video properties: AVI 2.49GB 22:34 809x605 Video: TSCC 809x605 15fps [Stream 00] Audio: PCM 22050Hz mono 352kbps [Stream 01] Choice of output doesn't seem to matter, they all end up distorted like the picture shows.

  Read the article

• RAM module randomly stopped working

  - by nhinkle

  My laptop is a Dell Inspiron e1505. It came with 2x512 MB of RAM installed, and about a year and a half ago I decided to upgrade it to 2x1 GB. I bought two 1GB memory modules from newegg and installed them, and all worked fine. Just last night my laptop was working fine; this morning I booted up and there was a BIOS warning saying "amount of system memory has changed". I tried reseating the modules, but that didn't fix it. Then I removed each one individually, and determined that one of the sticks appears to no longer be working. This happened very abruptly - I hadn't noticed any problems which might have been indicative of impending failure. Does anybody have any clue what may have caused this, and if there's any hope of making it work again? The memory only had a 30 day warranty, so I can't RMA it.

  Read the article

• MS Word 2007 Randomly Saves a blank doc

  - by Malnizzle

  Got a user that everyone once in awhile (maybe once every 2 weeks or so) will do a "save as" in their Word 2007 and the created, saved document will be blank. But most of the time, "save as" works fine. Already re-installed the whole Office Suite. It's fine when he does email attachments. This is not related to email. Sequence of events (from client): I create a new document and select SAVE AS I select a file to SAVE AS I create a name ie. ExampleFileA I select SAVE A blank document is what is saved I can sometimes recover the content of the document by selecting RECENT DOCUMENTS Yesterday, the file for ExampleFileA in RECENT DOCUMENTS was blank The situation has occurred with both pre-existing and newly created documents Any thoughts?

  Read the article

• Quickbooks and Cisco ASA 5505

  - by user41516

  I have a Cisco ASA 5505, and everything has seemed to function fine, however I have had problems with Quickbooks 2008 running super slow over the network (Samba) and narrowed it down to the Cisco box. Other Samba transfers seem to be pretty fast, and the Quickbooks file is not very large at all (<25 MB), and other Samba transfers seem to be fine. However, I'm not sure if Quickbooks uses another protocol or if there are other ports that need to be opened. Can anybody give me any clues on how to resolve or troubleshoot the problem or have any prior experience with running Quickbooks over a network?

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >