Search Results

Search found 21356 results on 855 pages for 'check digit'.

Page 652/855 | < Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• Can a non-redundant RAID5 cause any serious problems (compared to RAID0)?

  - by leemes

  I used to have a three-disc RAID5 (mdadm) in my computer for personal media storage (music, videos, photos, programs, games, ...). It had three discs with 750 GB each, resulting in an array capacity of 1.5 TB. One day (one year ago), I needed one of those discs to install another operating system. I thought, I don't need the redundancy anymore since I backup the most important stuff (personal photos e.g.) on an external disc anyway. So I decided to remove one of the three discs without converting the RAID to RAID0 or even two separate discs, because I had no temporary storage (since one cannot simply convert the RAID5 to RAID0 AFAIK). So now, for about one year, I have a non-redundant RAID5 with 2 of 3 discs running. Sometimes, one of the discs has a defective contact at the power cable or something similar causing the drive to stop working temporarily (I don't know exactly what it is). Since it still works when rebooting the computer and in most cases by calling some mdadm commands, it wasn't that problematic. Note that the data is not very critical, since I still have a backup of the most important stuff. But in the last few weeks, one of the drives fails very frequently (every few hours), so it gets really annoying to manage this. My questions are: Is there any disadvantage (apart from the annoying management) of a non-redundant RAID5 (with one drive less than typical) over a RAID0? If I understand it correctly, both have no redundancy and the same capacity. On a temporary drive failure, I can restart the array in both cases, assuming that the drive itself still works after the failure. Can it happen that the drive contents alter on a drive failure, making the array inconsistent? If so, can I tell mdadm to check the array for failures (without a file system level checking tool)? Since the drive most probably only has a defective contact causing it to fail for a second only, can I tell mdadm to automatically restart the array, so I will not even notice the failure if no application wanted to access the file system during the failure?

  Read the article

• How can I access user files on a disk moved from a Windows 7 machine to an XP machine?

  - by Fantius

  I moved the hard drive from one machine (Win 7) to another (XP) and now certain folders tell me "Access denied". I am logged in as an administrator. I had a different account on the other machine. Neither account authenticated to anything besides the local machine. The old machine is apparently dead, so I can't do anything in there like change permissions, etc. How can I access these files? Edit: After changing the ownerships of all the files and folders on the drive, I am getting a different error. And it is troubling me deeply. "xxx refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location." No change after rebooting. Any ideas? Surely the files are still there, right?

  Read the article

• Why is my server performance degrading to the point of stopping, periodically?

  - by Pascal Aschwanden

  So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

  Read the article

• Google Apps, SPF, softfail problem (validates with validation tools, but still softfails otherwise)

  - by mq.chen

  Hi, I guess this is probably a commonly asked and boring question but I'm really at a loss and I don't know what else to do. This might be a duplicate of other questions, but none of the solutions worked for me. I've Googled around and read just about anything I could find but I'm still puzzled as to why it doesn't work. The gist of my problem is that I have set-up Google Apps for a client of mine with the domain fintan.dk. Everthing works just excellent, except emails sent from *@fintan.dk (either with the Gmail web-interface or desktop client) to a non-Google Apps email gets a softfail (I have sent to my University email, an email hosted at MediaTemple and even Hotmail). The emails gets a pass when sent to a Google Apps or Gmail address though... (All emails from that domain are sent via email clients.) So this is what I have done so far: I've added the SPF record Google recommended (v=spf1 include:_spf.google.com ~all), waited several days hoping it would a DNS update delay problem. Now, three days later there is no change. I have verified the settings in the desktop clients several times. I have validated the records with validation tools like the SPF Query Tool, [email protected] and [email protected]. All of them validate and gives a pass, saying there shouldn't be a problem, but strangely there still is. So, I really don't know what else to do. Any help is very much appreciated. Thank you in advance!

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Why is my cron daemon is being killed every few minutes?

  - by user113215

  As of about a week ago, my cron daemon refuses to stay running. I'm using Debian 6 x64 on an OpenVZ virtual machine. Running something like pgrep cron shows that the daemon isn't running. I start the service with service cron start or /etc/init.d/cron start and it launches, but it disappears from the running process list after a few minutes (varying anywhere between 1 - 30 minutes before the process is killed again). Using strace -f service cron start, I can see that the process is being killed for some reason: nanosleep({60, 0}, <unfinished ...> +++ killed by SIGKILL +++ There's nothing relevant in /var/log/syslog, /var/log/messages, /var/log/auth.log, or /var/log/kern.log to explain why the the process is dying. The system has at least 800 MB of free memory, and cat /proc/loadavg returns 0.22 0.13 0.04 so resources shouldn't be the issue. With cron running, free -m reports: total used free shared buffers cached Mem: 1024 211 812 0 0 0 -/+ buffers/cache: 211 812 Swap: 0 0 0 I also tried removing and reinstalling the cron package using apt-get. Update: I initially thought the problem was a resource issues. I erased my entire VPS and started from a fresh Debian image. There is now nothing else running on the system, but even from a clean install my cron daemon is still being killed at random. What else should I check? How do I find out what's killing my crond?

  Read the article

• Fixing damaged partition table

  - by dr4cul4

  This is continuation of Recover Extended Partition , but this time I have different problem related partition table it self. I managed to restore partition that I needed and backed up files that were crucial to me (at least those that I had space to store somewhere) OK now get to the problem. My partition table is corrupted, booting RIP Linux I can mount it in truecrypt (and other ones that recovered), but that's basically it. When I launch GParted I have unallocated drive. GParted Dev info: Device Information Model: ATA ST2000DL003-9VT1 Size: 1.82TiB Path: /dev/sda Partition table: unrecognized Heads: 255 Sectors/track: 63 Cylinders: 243201 Total Sectors: 3907029168 Sector size: 512 When I check information on unallocated space I get: File system: unallocated Size: 1.82TiB First sector: 0 Last sector: 3907029167 Total sectors: 3907029168 Warning: Can't have a partition outside the disk! Now the output of testdisc (Analyze): TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 Current partition structure: Partition Start End Size in sectors > 1 P Linux 13132 242 39 16353 233 8 51744768 2 E extended LBA 16807 223 1 243201 254 63 3637021626 No partition is bootable 5 L Linux 16807 223 57 20430 39 25 58191872 X extended 20430 70 1 243201 78 13 3578816632 Invalid NTFS or EXFAT boot 6 L HPFS - NTFS 20430 71 58 243201 78 13 3578816512 6 LNext Now fdisk: # fdisk -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00039cd0 Device Boot Start End Blocks Id System /dev/sda1 210980864 262725631 25872384 83 Linux /dev/sda2 270018504 3907040129 1818510813 f W95 Ext'd (LBA) /dev/sda5 270018560 328210431 29095936 83 Linux /dev/sda6 328212480 3907028991 1789408256 7 HPFS/NTFS/exFAT Now I would like to fix that to arrange partitions correctly, but I have no idea which tool is capable of fixing that (tried, a few, some of them offered fixing, but it was to risky at the moment - still backing up data).

  Read the article

• torrent downloads not showing on Squid log

  - by noobroot

  hello, i have just a few months working as sysadmin, hence i still have lots to learn, first thing id like to do is as follows: We have an OpenBSD 4.5 box acting like firewall,dns,cache etc, the box has 2 network cards, one conected directly to the internet and the other to our switch, i used to work with sarg for the log analysis but then changed to the much faster free-sa. I use a daily free-sa report to check the bandwidth usage and report our top 5 bandwidth consumers (3 days a week being #1 and you will be buying the pizzas :D, we are a small company ~20 so we are very familiar). this was working really good until recently, one of us required to download some stuff via torrent (~3GB) and since the pizza rule is active for non-work related downloads, he told me (verified) that his download was indeed work related so i would dismiss that 3GB off his quota, but to my surprise the log didnt showed that 3GB, since his ip consumption was only around 290MB. More recently, since the FIFA world cup started, we know that some of the employees are watching the match's streaming, we know it and we dont care about it since, like already stated, we are a small company so we dont have restrictive policies, we all can chat, watch youtube, download anything we want BUT we are only allowed 300MB a day otherwise you'll get in the top5-pizza-board, anyway, that streaming consumption is also not showing in the free-sa reports. So my question is, why is these data being excluded from the reports? im thinking that the free-sa reports list only certain types of things but im also thinking if are the squid logs the ones that are not erm... logging these conections. Any help, guide, advice or clarification is appreciated.

  Read the article

• What can prevent a Server 2008 machine accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. I don't think it is this because we have a 2003 Server machine behind a different hardware firewall and that one works fine. What on earth is left?!

  Read the article

• Server side url scanner for malware, spyware , viruses and protect my visitors

  - by Vangel

  I have a forum/groups site that contains a lot of external URLs, sometimes direct download links. I want to protect my visitors from possible attacks from malware sites as they are mot likely to click on these links. CUrrently I implement DBL (spamhaus) but thats not enough. I want to run a background task to check the outgoing links first. I have looked at similar questions in StackOverflow (wrongly posted there) and here but fail to find a question same as mine or a good answer. People have suggested ClamAV , I don't believe it can detect Web hosted malware sites and its has a lot of missed detection. I have looked at google safe browsing service ( http://code.google.com/apis/safebrowsing/developers_guide_v2.html very complicated to implement or maintain plus midway I get lost :S ) I can go for commercial solution, anything to protect the visitors and my site brand. But I would like to hear the opinion of server admins and if anyone has implemented such a service. My Server is basic CentOS LAMP stack. thank you very much in advance.

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

• Which program is locking all my executable files?

  - by Tom Wijsman

  When updating any software product, as well as manually trying to replace .exe files, it says that access is denied to the file and in fact the System process is holding a handle to the file when I check it with Process Explorer. This must be a driver or something that is malfunctioning was my first though, but now I wonder how I figure out which driver / program is doing this and why it is so. Unlocker doesn't seem to be working for me, unless someone can tell me how to use it properly other than making it appear a magical wand in the notification area.... This is what Unlocker puts in my event log: The description for Event ID 1060 from source Application Popup cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer. If the event originated on another computer, the display information had to be saved with the event. The following information was included with the event: \??\C:\Program Files (x86)\Unlocker\UnlockerDriver5.sys the message resource is present but the message is not found in the string/message table Upon searching event 1060 I get: <file name> has been blocked from loading due to incompatibility with this system. Perhaps it is because I have 64 bit?

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• Can you see something wrong in my .htaccess?

  - by AlexV

  OK, after many search, trial and errors I've managed to create an .htaccess that do what I wanted (see explanations and questions after the code block): <IfModule mod_rewrite.c> RewriteEngine On #1 If the requested file is not url-mapper.php (to avoid .htaccess loop) RewriteCond %{REQUEST_FILENAME} (?<!url-mapper\.php)$ #2 If the requested URI does not end with an extension OR if the URI ends with .php* RewriteCond %{REQUEST_URI} !\.(.*) [OR] RewriteCond %{REQUEST_URI} \.php.*$ [NC] #3 If the requested URI is not in an excluded location RewriteCond %{REQUEST_URI} !^/seo-urls\/(excluded1|excluded2)(/.*)?$ #Then serve the URI via the mapper RewriteRule .* /seo-urls/url-mapper.php?uri=%{REQUEST_URI} [L,QSA] </IfModule> This is what the .htaccess should do: #1 is checking that the file requested is not url-mapper.php (to avoid infinite redirect loops). This file will always be at the root of the domain. #2 the .htaccess must only catch URLs that don't end with an extension (www.foo.com -- catch | www.foo.com/catch-me -- catch | www.foo.com/dont-catch.me -- don't catch) and URLs ending with .php* files (.php, .php4, .php5, .php123...). #3 some directories (and childs) can be excluded from the .htaccess (in this case /seo-urls/excluded1 and /seo-urls/excluded2). Finally the .htaccess feed the mapper with an hidden GET parameter named uri containing the requested uri. Even if I tested and everything works, I want to know if what I do is correct (and if it's the "best" way to do it). I've learned a lot with this "project" but I still consider myself a beginner at .htaccess and regular expressions so I want to triple check it there before putting it in production...

  Read the article

• Using Truecrypt to secure mySQL database, any pitfalls?

  - by Saul

  The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

  Read the article

• Need help trying to allow my remote PowerShell script to run on my Windows 2008 r2 Server

  - by Pure.Krome

  I've got a Windows 2008 r2 server with Sql Server 2008 r2 installed. I've got a Sql Server Agent which tries to run a Powershell job, but fails :- Message Executed as user: FooServer\SqlServerUser. A job step received an error at line 1 in a PowerShell script. The corresponding line is '& '\\polanski\Backups\Database\7ZipFooDatabases.ps1'' Correct the script and reschedule the job. The error information returned by PowerShell is: 'File \\polanski\Backups\Database\7ZipFooDatabases.ps1 cannot be loaded. The file \\polanski\Backups\Database\7ZipFooDatabases.ps1 is not digitally signed. The script will not execute on the system. Please see "get-help about_signing" for more details.. '. Process Exit Code -1. The step failed. Ok. So i run Powershell on that server then set the execution policy to unrestricted. To check .. PS C:\Users\theUser> Get-ExecutionPolicy Unrestricted PS C:\Users\theUser> Kewl :) but it still doesn't work :( Ok ... what happens when i try to run the powershell from the command line.... PS C:\Users\justin.adler . '\polanski\Backups\Database\7ZipMotorshoutDatabases.ps1' Security Warning Run only scripts that you trust. While scripts from the Internet can be useful, this script can potentially harm your computer. Do you want to run \\polanski\Backups\Database\7ZipFooDatabases.ps1? [D] Do not run [R] Run once [S] Suspend [?] Help (default is "D"): er..... didn't I already tell the server that ANY file can be ran? Notice the file is located at... \\polanski\Backups\Database\ So can someone make any suggestions?

  Read the article

• Nagios DNX plugins

  - by danneh3826

  I'm toying with the idea of multiple Nagios instances setup to monitor our infrastructure. I've looked at all the various methods of distributed Nagios checks, and I think DNX comes out the closest. DNX handles failure of worker nodes, that's fine. What happens if the main DNX server fails though? Is there a way to replicate the server too? I'm using AWS EC2 primarily, so I can utilise Elastic Load Balancing for the web UI, but I need to be able to handle the AZ where the monitoring server is to fail over, and essentially for a second to pick up the checking load (active/passive, active/active, so long as it doesn't fail completely) The other thing I'm trying to solve is an issue with routing. What I'd like is to have multiple nodes report a fault before Nagios confirms it as critical. Not the NRPE checks, as they're pretty self explanitory, but things more like check_ping. I often have routing issues out of AWS to certain datacenters, so Nagios can often report bad/no ping/timeout as a critical issue, even though the machine in question is working fine. Would it be possible to have a setup where a worker complains a service check is critical, and have a second worker node (positioned in another datacenter/AZ) also report the service as critical before the Nagios central server issues a critical alert? I realise I might be asking a bit much (how far down the line do you go setting up failover systems before it starts to get ridiculous), however surely someone must have thought of this scenario when developing DNX?

  Read the article

• sql server 2005 instance unresponsive and all db's are 'in recovery'

  - by user44650

  we've got a sql server 2005 instance that one of our guys messed up, i believe they killed the sql server service and restarted the computer, and when it came back all of our databases are "in recovery" and it times out every time we try to connect to it. it's been 'in recovery'and unable to connect to 'msbd' (also in recovery) whenever we try to use SSMC, for the last 4 days now. i'm unsure how to use the DBCC CHECKDB command to check the db integrity. we have backups(which we can't recover from because it keeps timing out), and it's a testing server, so nothing in production is really lost. is there any way to get it out of recovery mode? we have another sqlserver instance running that's just fine, but this instance keeps timing out. the errors i keep seeing are database msdb is being recovered. wait until recovery is finished and an exception occurred while executing a transact-sql statement or batch Timeout expired. any thoughts? we don't really have a DBA here, or anyone with much sql experience.

  Read the article

• postfix revived and delivered have the same values (?)

  - by thinkingbig

  I have configured my first server (Debian with ISPConfig). Generally i want to send bulk e-mails to our users, i configure postfix and turn on postfix... but... After 1 hour of sending emails i have logs like this: Grand Totals messages 21886 received 21883 delivered 0 forwarded 0 deferred 234 bounced 0 rejected (0%) 0 reject warnings 0 held 0 discarded (0%) 30805k bytes received 31280k bytes delivered 3 senders 3 sending hosts/domains 12588 recipients 3 recipient hosts/domains Per-Hour Traffic Summary time received delivered deferred bounced rejected -------------------------------------------------------------------- 0000-0100 0 0 0 0 0 0100-0200 0 0 0 0 0 0200-0300 0 0 0 0 0 0300-0400 0 0 0 0 0 0400-0500 0 0 0 0 0 0500-0600 0 0 0 0 0 0600-0700 0 0 0 0 0 0700-0800 0 0 0 0 0 0800-0900 0 0 0 0 0 0900-1000 0 0 0 0 0 1000-1100 0 0 0 0 0 1100-1200 0 0 0 0 0 1200-1300 0 0 0 0 0 1300-1400 0 0 0 0 0 1400-1500 0 0 0 0 0 1500-1600 15311 15306 0 168 0 1600-1700 6575 6577 0 66 0 1700-1800 0 0 0 0 0 1800-1900 0 0 0 0 0 1900-2000 0 0 0 0 0 2000-2100 0 0 0 0 0 2100-2200 0 0 0 0 0 2200-2300 0 0 0 0 0 2300-2400 0 0 0 0 0 Host/Domain Summary: Message Delivery sent cnt bytes defers avg dly max dly host/domain 21521 30353k 0 3.4 m 15.5 m wp.pl 355 919k 0 54.9 s 13.0 m mysenderdomainexample.pl 7 8477 0 1.7 s 1.9 s prokonto.pl Host/Domain Summary: Messages Received msg cnt bytes host/domain 21879 30786k mysenderdomainexample.pl 5 16196 mx4.wp.pl 1 3200 mx3.wp.pl Senders by message count 21783 [email protected] 96 [email protected] 6 from=< **So, my question is: 1) Why i have recived and delivered have the same values (approx)? 2) How can I check if an email has been delivered? 3) How to change default "root" and "www-data" user (FROM / RETURN PATH) to another? I have changed this in script, but postfix ignore scripting values and send every mail from root (we have .php send cron's in /etc/crontab) 4) WHY APPROX 100 % MAILS RECIVED HAS BEEN ADRESED TO MY SENDER HOST? Host/Domain Summary: Messages Received Waiting for respond, Regards TB**

  Read the article

• What could cause Windows 7 to hang whenever I install something?

  - by Larsenal

  I've had this problem when installing several different programs (iTunes, Adobe Acrobat Reader just to name two). Regardless of what the program is, the install usually gets at least 90% through the process and then just hangs. I don't see anything bad in the event log besides the following (and this didn't occur exactly at the time of install): wuaueng.dll (964) SUS20ClientDataStore: A request to write to the file "C:\Windows\SoftwareDistribution\DataStore\DataStore.edb" at offset 16252928 (0x0000000000f80000) for 32768 (0x00008000) bytes succeeded, but took an abnormally long time (185 seconds) to be serviced by the OS. This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. I've run check disk and it passed. I've had some problems with BIOS settings in the past with Windows 7, but I'm not sure whether that could be related. Update... I also see this error in the event log: Volume Shadow Copy Service error: Unexpected error querying for the IVssWriterCallback interface. hr = 0x80070005, Access is denied. . This is often caused by incorrect security settings in either the writer or requestor process. Operation: Gathering Writer Data Context: Writer Class Id: {e8132975-6f93-4464-a53e-1050253ae220} Writer Name: System Writer Writer Instance ID: {33493f01-ac1b-4efb-a378-3053ab03100d} One last wrinkle.... I see "Previous versions" of c:\ which look like they correspond to the time of attempted installation.

  Read the article

• Any ideas why Ettercap filters aren't seeing packet data?

  - by Bryan

  I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

  Read the article

• Recommend a UK based VPS host equivalent to Dreamhost [closed]

  - by Pez Cuckow

  I appreciate this question could be considered subjective and argumentative so can people make recommendations rather than arguing about the best. I believe the "correct" answer is the one closest to what I am looking for. Basically I live in the UK but have been using the US based Dreamhost for about 6 years now, and my web projects are getting to the scale where the websites need to the UK based to cope with the demand and load. I originally had shared hosting with Dreamhost but upgraded to a VPS a while ago, getting 512mb of RAM, unlimited disk space, bandwidth and domains for $30. Their control panel is a custom easy to use build that they have created in house and offers features very similar to other web panels (as far as I am aware). So basically my question boils down to, is there anywhere that offers an equivalent package? In all honesty as long as I have over 50gb HDD space and unlimited domains it doesn't really matter? Are there any VPS providers you would recommend as reliable? I promise to check every link posted, many thanks for your time!

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface? [migrated]

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

< Previous Page | 648 649 650 651 652 653 654 655 656 657 658 659  | Next Page >