Search Results

Search found 38640 results on 1546 pages for 'full table scan'.

Page 653/1546 | < Previous Page | 649 650 651 652 653 654 655 656 657 658 659 660  | Next Page >

• DBan not working because disk has bad sectors?

  - by canadiancreed

  Attempting to wipe the drive of a laptop that I have before it's sold, and normally use DBAN to do so. However this time it starts and then finishes instantly with the following message. "DBAN finished with non-fatal errors This is usually cause by disks with bad sectors" Have tried multiple flags such as noverify to force it to skip this check (it doesn't show bad sectors in the OS scan in windows). but the error always comes back. This is the only time that I've seen this message, as every other of the few drives I've used this software on usually take 3-5 hours to do their job.

  Read the article

• SAN performance issues storing SQL Server tempdb on a SAN that's being backed up

  - by user42724

  I'm afraid I don't know much about SAN's so please forgive my lack of detail or technical terms. As a developer I've just completed and put on an existing production system a new application but it would appear to have tipped the scales regarding the performance of the backups being taken from the SAN. As I understand it there's a mirror of the SAN being taken usually constantly at the block-level. However, there seem to be so many new writes to the disk that the SAN mirroring/backup process can no longer keep up. I believe I've narrowed this down to SQL Servers tempdb which exists on a drive that contributes the largest portion of the problem! In fact I think tempdb has be contributing the largest portion of the issues all along regardless of my application! My question therefore is whether the tempdb should ever be mirrored or backed on the SAN and whether anyone else has gone through this sort of pain already? I'm wondering whether it's a best practise to make sure that tempdb is never mirrored on a SAN simply because any writes to it don't need to be saved. This also raises a slightly connected question - is it better to rely on SQL Servers built-in database backups tools (DB in full-recovery mode with full/differential and transaction log backups) or, as is the case with our application, SQL server is in simple recovery mode and never backed up since the SAN is mirrored and backed up? Many thanks

  Read the article

• Modem doesn't seem to pass internet connection to router

  - by Vian Esterhuizen

  I was supplied a Cisco DPC3825 modem by my ISP and use a Cisco E4200 as my main router. Today the Internet just stopped working, just out of the blue, I can't think of anything that would have triggered it. It's been working pretty good for the past month except for a few random blips here and there. After some trouble shooting I realized that a direct wired connection to the modem would get me Internet access but if I was wired to the router as I was before I would have no connection. Assuming it was router I connected a TP-Link WR841N but it had the exact same problem. Also, connecting to the router via Wi-Fi from multiple devices will connect me to the router but I still can't get access to the Internet. From these test, it seems that the modem just won't send Internet through to the router but is clearly connecting and able to directly connect to my PC. What I've Tried A full reset and factory reset on the E4200 A full reset on the modem (but I believe my ISP has remote access to the modem because the passwords and so on are always set back). My ISP has remotely reconfigured the modem What I Should Try What else can I try? What should I do to try to narrow down the issue? Can you figure out what the problem might be based on this information?

  Read the article

• Configure IPv6 routing

  - by godlark

  I've got IPv6 addresses from SIXXS. My host is connected with SIXXS network over a AICCU tunnel ("sixxs" interface). My host address is 2001:::2, the host on the end has address 2001:::1. On my host IPv6 is fully accessible. I have problem with configuring IPv6 network on VMs. I use VirtualBox, the VM (Ubuntu) uses tap1 (on the host bridged by br0) #!/bin/sh PATH=/sbin:/usr/bin:/bin:/usr/bin:/usr/sbin # create a tap tunctl -t tap1 ip link set up dev tap1 # create the bridge brctl addbr br0 brctl addif br0 tap1 # set the IP address and routing ip link set up dev br0 ip -6 route del 2001:6a0:200:172::/64 dev sixxs ip -6 route add 2001:6a0:200:172::1 dev sixxs ip -6 addr add 2001:6a0:200:172::2/64 dev br0 ip -6 route add 2001:6a0:200:172::2/64 dev br0 Host: routing table: 2001:6a0:200:172::1 dev sixxs metric 1024 2001:6a0:200:172::/64 dev br0 proto kernel metric 256 2001:6a0:200:172::/64 dev br0 metric 1024 2000::/3 dev sixxs metric 1024 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sixxs proto kernel metric 256 fe80::/64 dev br0 proto kernel metric 256 fe80::/64 dev tap1 proto kernel metric 256 default via 2001:6a0:200:172::1 dev sixxs metric 1024 Guest: interface eth1 (it is connected with tap1): auto eth1 iface eth1 inet6 static address 2001:6a0:200:172::3 netmask 64 gateway 2001:6a0:200:172::2 Guest: routing table 2001:6a0:200:172::/64 dev eth1 proto kernel metric 256 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev eth1 proto kernel metric 256 default via 2001:6a0:200:172::2 dev eth1 metric 1024 The guest pings to the host, the host pings to the guest, the host pings to 2001:6a0:200:172::1, but the guest doesn't ping to 2001:6a0:200:172::1. The guest tries to ping, on the host (by tcdump) I can capture its packets, but the host doesn't send them to 2001:6a0:200:172::1. What have I missed in configuration?

  Read the article

• Hard disk problem pop up warning

  - by Leonardo

  I'm using windows 7 ultimate and it started to give me this hard disk problem warning that i had before in another OS that made me disable smart, it has been over a year since i did and my pc is running ok so my HDD is ok. all i wanna do is disable this warning that popsup while i'm gaming or doing anything else. thanks for your help :) Edit: (adding in info that was added as an answer instead of part of the question) So it's me again and i agree with both answers but i don't have the money right now to buy a new one, and yeah it could die now, i can't say. so i uploaded an image of hd tune pro scan on my HDD thanks again! anymore information would be even better, bye.

  Read the article

• Server Performance

  - by sb12

  I know very little about performance tuning of servers etc... so i thought i'd put this up here as i start some research on it, just to get some direction. I am in the process of migrating from my old server to a new one - both are 64 bit machines. One is a few years old, the other brand new (PowerEdge R410). The old server spec is: 2 cpus, 3.4GHz Pentiums, 8G of RAM, Fedora 11 currently installed The new server spec is: 16 cpus, 3.2 GHz Xeon, 16G of RAM, CentOS 6.2 installed. Also RAID10 is on the new server - no RAID on the old one. Both servers currently have the same database (MySQL) with the same data migrated. I wrote a Perl script that simply steps through each row of a table in the database (about 18000 rows) and updates a value in that row. Every row in the table is updated. Out of curiosity i ran this perl script on both machines, just to see how the new server would perform vs. the old one, and it produced interesting results: The old server was twice as fast as the new one to complete. Looking at the database, both are configured exactly the same (the new one being a dump of the old one...)... Anyone any ideas why this would be given the hardware gap between both? As i said i'm about to start some digging, but thought i'd put this up here to maybe get some good direction.... Many thanks in advance..

  Read the article

• How to drop packets in a custom Intrusion Detection System

  - by tzoukos

  Hi there, I'm trying to build a custom Intrusion Detection and Prevention System (IDS/IPS). I found a great utility named ROPE which can scan the packet payload and drop the packet that doesn't follow the rules, set by a script. This serves my purpose completely, since what I want to do is check the payload for some specific text and then drop it or allow it ( the string feature in iptables wouldn't do me any good, because I want to check more than one string in tha payload, like usernames, id's, etc ). However, ROPE is really old and despite my many attempts I haven't managed to install it properly. Do you know any similar program that will help me drop packets in iptables depending on the payload? Any suggestion is greatly appreciated :)

  Read the article

• Virus that duplicates word documents as exe

  - by Bob Rivers

  Hi, We are facing a virus problem on our network, but I'm unable to identify it, so we can't properly deal with it. The symptoms are that the virus duplicates a word document (.doc) generating a new archive with the same name, but with an exe extension, and, after that, the virus hides the original file. So, when the user clicks over the file, it propagates itself. Symantec AV seems to be able to block it: every time that the virus tries to generate the exe, symantec blocks it, but at this point, the original file was already converted to hidden, so the user thinks that the file has been deleted. Symantec identifies it as a simple trojan horse. I already started a full scan, but it didn't found nothing. I'm trying to know the virus name in order to fight it. Does anyone has any kind of information? TIA, Bob

  Read the article

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• PHP not loading php.ini in directory or following error_reporting() on Windows 7

  - by Marcus

  Normally I develop under E_ALL error level, but for sanity on this project I want notices and strict off. So initially tried: error_reporting(E_ALL & ~(E_STRICT|E_NOTICE)); And several other combinations of the same thing, nothing worked. Next I tried to create a local php.ini the directory with error_reporting = E_ALL & ~E_NOTICE but nope, that didn't work either. phpinfo() is reporting: Scan this dir for additional .ini files: (none) Can someone help me fix either of these problems? Preferably both! Thanks! I'm running PHP Version 5.2.13 on Apache/2.2.14 under Windows 7 x64.

  Read the article

• Windows FAT/NTFS Low-Level Disk Viewer (Norton DiskEdit alternative)

  - by Synetech inc.

  Hi, One of my most valuable software tools has always been Norton DiskEdit from Norton Utilities/Symantec Systemworks. I have used it for years for so many things, including, but not limited to learning file-systems. I am now in search of a similar tool that can let me view FAT and NTFS disks at a low and high level under Windows. I have seen Runtime Software’s DiskExplorer, but unfortunately, it is limited in a number of ways, particularly annoying is that it does not really let you view the disk as structured (it does not let you see directory entries from a directory that is fragmented like DiskEdit can without doing a too-exhaustive scan which doesn’t even work for FAT partitions that have cluster sizes <4KB). Does anyone know of a Windows alternative of a Norton DiskEditor? Thanks a lot.

  Read the article

• Getting an error when mounting LVM snapshot

  - by Sandra

  I have migrated a file based Xen guest to LVM using dd bs=1M if=/dev/zero of=/dev/vg00/vm10 qemu-img convert ~/vm10.qcow2 -O raw /dev/vg00/vm10 and changed the Xen domain file for the VM to use the LV instead of the old file. The VM boots up, and now on the Xen host would I like to make a snapshot of the running VM. # lvcreate --size 10G --snapshot --name vm10-snapshot /dev/vg00/vm10 Logical volume "vm10-snapshot" created # mount /dev/vg00/vm10-snapshot /mnt/snapshot/ mount: you must specify the filesystem type # dmesg |tail EXT3 FS on dm-3, internal journal EXT3-fs: mounted filesystem with ordered data mode. hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-4. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock VFS: Can't find ext3 filesystem on dev dm-2. hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock hfs: unable to find HFS+ superblock For some reason it can't see it is an EXT3 filesystem. I have also tried to mount with -t ext3, but still didn't mount. # lvdisplay --- Logical volume --- LV Name /dev/vg00/vm10 VG Name vg00 LV UUID I1y1vQ-Bac5-5jwW-melh-TY5h-l9NO-qaelKk LV Write Access read/write LV snapshot status source of /dev/vg00/vm10-snapshot [active] LV Status available # open 2 LV Size 8.00 GB Current LE 2048 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:2 --- Logical volume --- LV Name /dev/vg00/vm10-snapshot VG Name vg00 LV UUID GWsOx3-TPpr-GW64-uiMz-u1YN-QU4h-l0Kala LV Write Access read/write LV snapshot status active destination for /dev/vg00/vm10 LV Status available # open 0 LV Size 8.00 GB Current LE 2048 COW-table size 10.00 GB COW-table LE 2560 Allocated to snapshot 0.00% Snapshot chunk size 4.00 KB Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:4 # What could the problem be?

  Read the article

• Big square ads appear in lower right corner of both IE and Chrome

  - by BrianK

  In both IE and Chrome, large ads appear in the lower right corner of the browser window. Sometime they look reputable like for Microsoft, but sometimes they are big flashing boxes that say "You have won". Right now I am looking at "Need to lose 30 lbs?" I ran Microsofot Security Essentials and it didn't find anything. I then ran Windows Defender Offline (boot from CD). WDO found five things lincluding browser hijack that caused the wrong page to appear after clicking a link. It reported that it cleaned successfully, after which I ran a quick scan to confirm. After rebooting I still see the ads. Do I still have an infection? Any other tools to try? What about ComboFix? Thanks Update: Here's a screenshot - on superuser

  Read the article

• TP-Link TL-WA701N not working good as wireless extender

  - by djechelon

  I bought the device in subject to extend the range of my WPA2/PSK-protected wifi network powered by a TP-Link TL-WR340G device (AP+router). I configured it as follows: Operation mode: Universal Repeater MAC of AP: scanned my SSID and got it Channel width: 20MHz Security options: the same as the parent AP (WPA2/PSK with AES encryption) After configuration inSSIDer shows me two APs beaconing the same SSID at different SNRs (because I was with my laptop close to the extender). After a few hours my tablet, far from the parent AP, stopped working. I found that the scan reported two networks with the same SSID: one WPA-protected and one free at all. This happened very frequently. Rebooting the extender by unplugging it worked but this doesn't last long. Sometimes the extender stops transmitting at all, sometimes it beacons an open network to which nobody can connect (because there is no DHCP). What's wrong with my configuration?

  Read the article

• Htpc aka "Media Center": cheap and *silent*?

  - by Unknown

  It may be me, or the place I live (Italy), but it seems pretty hard to get a build or a prebuilt nettop or a laptop that fits the need. I need something silent able to playback all h.264 fullhd content without stuttering, and well (and not loosing the hw acceleration because of softsubs...) silent not ugly silent and (possibly) cheap. I'm going the linux route, therefore i'm moving towards a cpu-based or nvida-integrated solution (i don't think ati hw accelerated playback - or the intel "hd" acceleration - is useable yet). Ion nettop; it's either the Acer Revo (but here it's incredibly pricey and it's hard to find the dualcore version) or the Asrock Ion 330, that in the current version is rated "silent" at 26Db. 26. Sounds pretty noisy to me!!! the previous version was even worse. was this product really aimed at htpc market?? the Dell Zino - i think it's ATI based unfortunately. Laptop: correct me if I'm wrong: sub 600€/$ units are quite loud under full load (because of the tiny fans). ULW laptops are indeed quite similar: tiniest fans = high pitched noise and the cpu still lacks power for non hd-accelerated video decoding Handmade build: little money can be saved with underpowered cpus, a low-midrange cpu would help in the case of non-hw-accelerated content the cases are quite pricey the PSU one has to get ranges between 100/150 €/$ minimum to keep the noise down a low-mid build, all included, sums up to over 650 €/$ for a still-looking-ugly-unit, without the blu-ray drive. Please help. What do you advise on this? ;) Am I ignoring laptops too much, maybe? Are low-priced Acers that noisy/high pitched under full load?

  Read the article

• VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

  - by user223903

  Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

  Read the article

• Sql Server Management Studio: Change Prefix or Suffix characters

  - by PhantomDrummer

  I have an instance of SSMS 2008, for which the option to edit data in a table doesn't work. If I right-click on any table in the Object Explorer and select 'Edit top 200 rows' I get an error dialog 'Invalid prefix or suffix characters. (MS Visual Database Tools)'. The error seems to be associated specifically with SSMS, not with SQL Server (because this SSMS instance gives the same error no matter what database I connect to, but I've verified I can connect to some of the same databases using SSMS on other machines without the error). (However, our firewall prevents me using SSMS on other machines for some crucial tasks, so I do need to fix the problem). Googling for the error suggests that I should change the prefix, suffix or escape character, but without any indication of how you can make that change in SSMS. I'd also note that I'm not aware of having done any customization on SSMS since installing it, so would be surprised at having to make such a change now. Does anyone have any idea what the error message means or what I can do about it? Or how I can change the prefix/suffix/escape characters if that is really the problem.

  Read the article

• How to add a Linux Partition on FreeBSD

  - by Ömer

  Today I installed FreeBSD 9.0 PPC on my Mac mini G4 with 40GB HDD. During installation, (using the FSBD utility 'gpart') I have allocated a total of about 23GB for FreeBSD leaving 17GB totally free (neither partitioned, nor formatted) for a later Linux installation. Now, when try to install Linux (Ubuntu 10.10 PPC) on the remaining 17GB, the Linux/Ubuntu installer (or Linux's Disk Utility for the same matter) wants presumably a linux partition and when I try to add a (Linux) partition on that area using Linux DU it fails with this message: Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/hda, start=23363101696, size=16644660224, type= Entering MS-DOS parser (offset=0, size=40007761920) No MSDOS_MAGIC found Exiting MS-DOS parser Entering Apple parser Mac MAGIC found, block_size=512 map_count = 17 Leaving Apple parser Apple partition table detected containing partition table scheme = 2 got it Error: The partition's data region doesn't occupy the entire partition. ped_disk_new() failed Now, I'm trying to add a Linux partition on FreeBSD running on the harddisk. I use seemingly most suitable tool for this job: gpart. Here is the 'gpart show ad0' But it seems unable to add a Linux partition because "man gpart" doesn't list either "Linux Partition" nor anything like Ext2 or Ext3/Ext4. The closest thing to Linux Partition in gpart is "mbr" but it doesn't work: #gpart add -t mbr ado So, how to add properly a Linux Partition on FreeBSD? Thanks.

  Read the article

• Do I need liquid cooling?

  - by Mrrvomun

  I'm building a computer mainly for gaming and developing games. It's going to be a three screen system with two GeForce GTX 460's and a quad-core i7. The newegg wattage calculator says I need around 900W. The case I intend to get is this one. Full specs if you need 'em are at the end of this post. I have no intentions to overclock the system at the moment, but this may change in the future. I've done a lot of research on the subject, and the answers I've found indicate that it takes a heck of a lot of power to require liquid cooling, and most non-overclocked systems don't need it. But I haven't seen a question about a system with two GPU's, so I ask you the following two questions: Assuming that the system is used for gaming for very extended periods of time (say 4-6 hours at a time, nonstop) with all three screens running at full 1080p, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? If the system is used under the same circumstances as above, and is overclocked to a reasonable level, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? Specs: Intel Core i7 16GB DDR3 Two nVIDIA GeForce GTX 460 3TB HDD Two DVD-RW writers Thermaltake 1050W power supply Case is linked above

  Read the article

• Clean up infected computer from viruses

  - by ripper234

  I have a computer which had AVG Free installed from day one. After several months of operation, it starts detecting viruses and trojans all the time. Besides running a full scan, what should I do to clean the computer? Should I install another anti-virus or anti-malware tool (can it help?), or once viruses infect a system the only real solution is a clean format? (Lately I've heard of viruses that burn themselves in the BIOS, so a clean format might not always work ... how common is this technique? Should I burn a fresh BIOS as well?)

  Read the article

• Importing XML into an AWS RDS instance

  - by RoyHB

  I'm trying to load some xml into an AWS RDS (mySql) instance. The xml looks like: (it's an xml dump of the ISO-3661 codes) <?xml version="1.0" encoding="UTF-8"?> <countries> <countries name="Afghanistan" alpha-2="AF" alpha-3="AFG" country-code="004" iso_3166-2="ISO 3166-2:AF" region-code="142" sub-region-code="034"/> <countries name="Åland Islands" alpha-2="AX" alpha-3="ALA" country-code="248" iso_3166-2="ISO 3166-2:AX" region-code="150" sub-region-code="154"/> <countries name="Albania" alpha-2="AL" alpha-3="ALB" country-code="008" iso_3166-2="ISO 3166-2:AL" region-code="150" sub-region-code="039"/> <countries name="Algeria" alpha-2="DZ" alpha-3="DZA" country-code="012" iso_3166-2="ISO 3166-2:DZ" region-code="002" sub-region-code="015"/> The command that I'm running is: LOAD XML LOCAL INFILE '/var/www/ISO-3166_SMS_Country_Codes.xml' INTO TABLE `ISO-3661-codes`(`name`,`alpha-2`,`alpha-3`,`country-code`,`region-code`,`sub-region-code`); The error message I get is: ERROR 1148 (42000): The used command is not allowed with this MySQL version The infile that is referenced exists, I've selected a database before running the command and I have appropriate privileges on the database. The column names in the database table exactly match the xml field names.

  Read the article

• Mail.app doesn't detect sender in Address Book

  - by CoreSandello

  Hi there. I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

  Read the article

• After using lvextend, I can't recover unused space

  - by Cory Gagliardi

  I needed to add more disk space to my CentOS VM, so I added another virtual disk, then used lvextend to add the space to the existing partition. The steps I followed was: echo "- - -" > /sys/class/scsi_host/host0/scan pvcreate /dev/sdb vgextend VolGroup00 /dev/sdb lvextend -l +100%FREE /dev/VolGroup00/LogVol00 resize2fs /dev/VolGroup00/LogVol00 This worked fine. I subsequently filled up the VM, then deleted most of the used disk space. However, the unused disk space was never recovered after I deleted all of the files. This will illustrate what I'm saying better: # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 61G 32G 26G 56% / /dev/sda1 99M 20M 75M 21% /boot tmpfs 1006M 0 1006M 0% /dev/shm # pwd; du -h --max-depth=0 / 5.1G . I cannot figure out how to get the partition to see that only 5.1 GB is used. Any ideas what I'm doing wrong?

  Read the article

• Any command line tool checking windows domain password?

  - by Chen Jun

  Does Windows provide a command line utility that lets me check a domain user's password? It is sufficient that the utility returns success(0) if I provide a matching domain user name and password. Alternatively, is there a simple VB/JS script that can do this? I'm the Intranet admin of my company and have the default password set for corporate staff, so I'd like to quickly scan which users have not changed their default password. Better yet, are there any books or websites which cover such topics so that I can get more information?

  Read the article

• Path of md device wrong after reboot

  - by flammi88

  I have to set up a software raid (level1) on a Ubuntu server 12.04. It should serve files in the network via Samba. The server has the following disks: 250gb Sata hdd (Ubuntu is installed on that drive) 2 TB Sata hdd (first disk in raid array, data disk) 2 TB Sata hdd (second data disk) I created one partition on every data disk with the type Linux raid autodetect. In the second step I created the raid1 with the following command: mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdb1 /dev/sdc1 After that, I added the array to the mdconf: mdadm --examine --scan >> /etc/mdadm/mdadm.conf The problem is: After a reboot the array is not available on the path /dev/md0. Instead of that it gets reassembled as /dev/md/0 but it is not very reliable. Has anybody a solution for this issue?

  Read the article

< Previous Page | 649 650 651 652 653 654 655 656 657 658 659 660  | Next Page >