Search Results

Search found 19018 results on 761 pages for 'indicator network'.

Page 658/761 | < Previous Page | 654 655 656 657 658 659 660 661 662 663 664 665  | Next Page >

• cannot connect to vpn server (error 721)

  - by callmeblessed

  I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Configuration for Router Behind Uverse 2Wire

  - by Nori

  I have a 2Wire Uverse router(RG). I'm not particularly fond of it and want to use it as a modem only. I have a Linksys router with Tomato firmware on it and want that to be configured as the router. Most of the "guides" I've seen in my searches has been to enable DMZ Plus mode, but I don't see a way to make that work while my router has a static IP address. I played with it for quite some time yesterday and didn't see a way to get it to work. Then I ran across a setting in broadband for configuring another network. I played with that for a little bit but ran out of time and couldn't get it to work. So my question is for anyone out there who has Uverse and successfully setup a Tomato based firmware router behind the RG. How did you get it configured? I'm sure if I continued playing with it I could get it to work, but if someone out there already has it working then that would make my life easier. Thoughts? Thanks.

  Read the article

• How do I get netcat to accept connections from outside the LAN?

  - by Chris

  I'm using netcat as a backend to shovel data back and forth for a program I'm making. I tested my program on the local network, and once it worked I thought it would be a matter of simply forwarding a port from my router to have my program work over the internet. Alas! This seems not to be the case. If I start netcat listening on port 6666 with: nc -vv -l -p 6666, then go to 127.0.0.1:6666 in a browser, as expected I see a HTTP GET request come through netcat (and my browser sits waiting in vain). If I go to my.external.ip.address:6666, however, nothing comes through at all and the browser displays 'could not connect to my.external.ip.address:6666'. I know that the port is correctly forwarded, as www.canyouseeme.org says port 6666 is open (and when netcat is not listening, that its closed). If I run netcat with -g my.adslmodem's.local.address to set the gateway address, I get the same behavior. Am I using this command line option correctly? Any insight as to what I'm doing wrong?

  Read the article

• Google.com always forward me to google.com.hk

  - by Ta Coen

  Any one could help me to figure out why Google.com always forward me to google.com.hk? $ dig google.com www.google.com. 509426 IN CNAME www.l.google.com. www.l.google.com. 100 IN A 74.125.71.147 www.l.google.com. 100 IN A 74.125.71.99 www.l.google.com. 100 IN A 74.125.71.105 www.l.google.com. 100 IN A 74.125.71.106 www.l.google.com. 100 IN A 74.125.71.104 www.l.google.com. 100 IN A 74.125.71.103 and $ dig google.com.hk www.google.com.hk. 261572 IN CNAME www.google.com. www.google.com. 589217 IN CNAME www.l.google.com. www.l.google.com. 139 IN A 74.125.235.17 www.l.google.com. 139 IN A 74.125.235.18 www.l.google.com. 139 IN A 74.125.235.19 www.l.google.com. 139 IN A 74.125.235.20 www.l.google.com. 139 IN A 74.125.235.16 How to make my network always goes to google.com?

  Read the article

• Dropped connections between Linux Servers in Data Center

  - by Emil H

  I have a number of linux servers at a us-based datacenter. The servers were installed by the hosting company, and are running fedora core. We're experiencing problems with dropped connections. The issue seems to be that when we attempt to connect to one of the other servers after a period of inactivity, the first connection attempt will fail, and sometimes the second. However, after that the connection succeds and it works for a while. This happens for both mysql connections and raw socket connections, but only seems to occur when connecting to some of our servers. The confusing part is that it some of the servers for which we see different behaviors have identical hardware configuration and software. For example, it happens when connecting to a server called mysql2, but not for a server called mysql3. These servers were installed at the same time, but the same specifications. The problem can be reproduced somewhat reliably, but only after waiting fifteen minutes to half an hour. This makes it hard to diagnose, and even harder since I'm not really sure what to look for. I realize that connections sometimes failed, and that we should write our applications to compensate for this but these servers all in the same data center. Why would it matter if two servers haven't communicated for a while? Does anybody have an idea what might be causing this? Is it a server configuration problem or a network problem that I should contact the hosting company about. What do I tell them to look for? Unfortunately our experience has been that the support staff doesn't investigate problems in depth unless we give them detailed directions.

  Read the article

• Exchange 2003 ActiveSync problem

  - by colemanm

  We're having problems getting iPhones to sync properly with SBS 2003 Exchange. When you add a new Exchange ActiveSync account on an iPhone and enter all the pertinent information, it shows a "Verifying Exchange account info" message for a minute or so, then says everything's verified and asks what you want to sync, Mail, Contacts, Calendars... so it looks like it's working. However, when you go to the Mail app and select the Exchange email account, it just shows an "Inbox" folder with nothing in it. When you try refreshing, it attempts for a second, then says "Last Updated" with a timestamp, as if it worked, but there's no mail and no error message/feedback at all. I think I've narrowed it down to some sort of certificate issue, but I'm having trouble finding out where to go from here... I ran MS's Exchange connectivity testing tool with these results: Our cert was purchased from Network Solutions, and I'd already added it to the IIS Default Website for OWA purposes. But this report makes it look like the cert is somehow problematic. I don't know what to do now... Here's a shot of the cert details, just in case:

  Read the article

• Java applet class never found

  - by Andrew

  I am having a problem with the java plugins of all three major browsers: chromium, firefox and Internet Explorer. The issue is that applets will always fail to load and yield errors no matter what website or what applet I am trying to use. I can not see any of the example applets on oracle's website; I can not launch the minecraft browser applet; nor can I launch any applet across the web using any browser. I always receive a "class not found:AppletClassHere.class" error. I know that my browser plugin must be working correctly because I can launch the Cisco Nac applet each time I connect to my network and I can launch my own simple applets offline. I am connecting to the internet through a vpn in case that is important. It also seems like a lot of other people I know are having this issue. Re-installing the plugin does not appear to fix the issue. I am asking this question to find out the cause of this problem, and any possible solutions. Thank you.

  Read the article

• Unzipping archives, preserving folder hierarchy

  - by Hydrangea

  I've got a problem and am not sure what it is, but hope someone can help me think this through because this has me stumped. Backstory: I wrote a Java app (Android) that unzips some zip files downloaded from the network. Until now, this was working great. Then, this week, the archives that I'm creating on my pc (in Ubuntu 12.04) unzip on the Android phone into a flat hierarchy instead of preserving the folders. I'm creating the archives the same way (right-click on folder compress) but even though my old archives (created in 10.04) still unzip as expected, the new ones don't. On Ubuntu, the new zip files look the same to me as the old ones. When unzipped on my pc the folders in these new archives are restored the same as the old ones... it's the Android app that extracts the old ones fine and the new ones flat. What I really want to know, though, is what the difference between the archives is. Question: How could one determine why one zip archive would be extracted with folder hierarchy preserved, when an identical one (to all appearances on Ubuntu 12.04) is extracted with no hierarchy? Are there different ways in which a .zip file can "have" folders, but Ubuntu doesn't distinguish between them?

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• Are applications optimized for XenApp?

  - by damitamit

  Our IT dept are about to deploy virtualized apps using Citrix XenApp. One of these apps will be Dynamics AX 4.0 SP2, a ERP client (which I develop on). They have supposedly reached a roadblock because an external 'Dynamics AX Consultant' has told our IT Dept that Dynamics 4 will not work optimally on Citrix and will run very slow because it is not optimized for Citrix. We have it running in a Test environment now and seems ok. They have been told that the only 'solution' is to upgrade to Dynamics AX 2009 where supposedly this problem as been fixed. (not a small task for my team!) When I heard about this, I was quite surprised. From my brief knowledge of Citrix, I thought it would be application independent. How does the citrix app virtualization work, in that a particular app would work better than others on citrix? Would the speed of the virtualized app not just depend on the resources/network connection the citrix server has? FYI, Dynamics AX is a 3-tier client/server system, so the client will be accessing a AOS application server, which then accesses the database. Please enlighten me :)

  Read the article

• Backup with Mercurial and Robocopy?

  - by Andrew Neely

  The Problem We would like to backup our critical files from several network shares to a removable hard drive. We want to automate the backup so we don't have to remember to run it. It needs to finish overnight. Furthermore, we want to be able to preserve multiple versions of each file so we can back out of our user's mistakes easier. Background Information I work in a large Windows-based enterprise with a centralized IT section who is responsible for all backups. Their backups are geared towards disaster recovery and not user error, and require upper-level management approval for any non-disaster recoveries. Several times we have noticed that our backups have failed, we weren't notified. I do not have administrative rights to the server or my desktop. We are trying to backup some 198,000 files spanning about 240 gigabytes. These files rarely change. Our backup drive is one terabyte. My Proposed Solution What I would like to do is to write a batch file using Robocopy with the /mir option along with Mercurial SCM to store all versions of the file. I would do an hg add followed by an hg commit before each execution of Robocopy to save the current state, and then make a mirrored copy of the file structures. The problem is the /mir will delete every folder not present in the source, and Mercurial stores the repository in a .hg folder in the destination folder. Does anybody know how I could either convince Mercurial to store the .hg folder elsewhere, or convince Robocopy not to delete it from the destination? I'm trying to avoid writing a custom program do to copying.

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

• I need an admin toolset for Windows 2003 and 2008

  - by eugeneK

  i know this is way too general question but anyway. I need few tools, will write down my tasks as sysadmin and if you have any to automate my job i would be glad to hear. I don't mind paying for software needed unless it is way too expensive. First of i backup all files on server at local/office storage. I 7zip all SQL backup files and then move them over network to centralized location and then FTP them from office PC which has no FTP server installed and cannot have one. Backups happen at 4AM at the morning thus i need to set time for compressing and afterward FTPing. Then i FTP all IIS web application as differentiation backup, same goes for VOD movies. Second tool i need is system monitor which will monitor all servers from themselves and from external location for CPU/Memory/Hard disk and other basic failures. This tool should able to execute Website address with parameters which will send me an email with all report on failure. Third tool i need is a way to get all Event Logs from 10 Windows based servers without accessing each any of them manually. If you know any solution, thanks in advance.

  Read the article

• Can't ping my Window 7 machine from within a Windows XP virtual machine

  - by Jonathan Conway

  I have Windows 7 installed as my primary operating system, on a laptop that's on my home network (wireless). I'm using Microsoft Virtual PC 2007 SP1 to run a virtual machine of Windows XP SP3, in which I want to access the Windows 7 instance, both to browse a shared folder and access the local Apache server. So far I can ping my Windows 7 IP address (IPv4) and access the apache server through the web browser through HTTP. However using my machine name never seems to work. Pinging it fails, and I can't access my apache server using it either. The problem seems to be something to do with my machine's name being registered under IPv6 rather than IPv4. I'm at a loss what to do. Should I try to set up IPv6 on the virtual machine? Not sure how to go about that. Or maybe I should somehow get my machine name on Windows 7 to work with IPv4? Although I think it already does, because I can ping it from a separate box (running Ubuntu), which is only registered under IPv6.

  Read the article

• How to use Python to read the physical address(MAC ID) [closed]

  - by getjoefree

  I want to read the physical address of the NIC model, i can get the results that i want to with SED.EXE before, but SED.EXE does not support my environment but Python ok, who have the means to do it. The general situation (not plug the network cable, it is impossible to obtain IP address): Ethernet adapter: Connection-specific DNS Suffix.: Chianet Description ...........: Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller Physical Address .........: A4-BA-DB-9D-1E-8E Dhcp Enabled ...........: Yes Autoconfiguration Enabled ....: Yes Ethernet adapter 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1510 Wireless-N WLAN Mini-Card Physical Address. . . . . . . . . : 00-23-4D-D9-C0-28 The description of the NIC different, we can use this to fetch the corresponding physical address, base on Physical Address does not work, because the computer with the WLAN Card, I want to use Python to read my computer the card information and after Python handles an output file, output file format: SET MAC = A4BADB9D1E8E and sed format: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" > WINMAC.BAT getmac.sed: /Marvell Yukon 88E8040/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; }

  Read the article

• Backup and Archive Strategy Question

  - by OneNerd

  I am having trouble finding a backup strategy for our code assets that 'just works' without any manual intervention. Goal is to have an off-site backup (a synchronized one) so that when we check-in files, create builds, etc. to the network drive, the entire folder structure is automatically synchronized and backed-up (in real time, or 1x per day) at some off-site location so if our office blows up, we don't lose all of our data. I have looked into some online backup services, but have not yet had any success. Some are quirky/buggy, others limit file size and/or kinds of files (which doesn't work well for developer files). Everything gets checked in and saved to a single server (on a Raid Mirror), so we just need to have a folder on that server backed up/synchronized to some off-site location. So my question is this. What are you using for your off-site backup strategy. What software, system, or service? Is there a be-all/end-all system of backing up your code assets that I just haven't found yet? Thanks

  Read the article

• How do I get "Back to My Mac" (using MobileMe) from Windows?

  - by benzado

  I have a MobileMe subscription and a Mac at home with "Back to My Mac" enabled. When I'm away from home, this service lets me use another Mac to connect to my Mac back home and access file sharing, screen sharing, etc. As far as I know, the service doesn't use any proprietary protocols, so in theory I should also be able to get "Back to My Mac" from a Windows PC. This MacWorld article explains how it works. Basically, it uses Wide-Area Bonjour to give your Mac a domain name like hostname.username.members.mac.com. Remote computers can find your Mac using that address, then connect to it using a private VPN. The "Wide Area Bonjour" part seems to make it a little more complicated than simply a regular domain name, though. Note that I'm not interested in using the methods described by LifeHacker, which doesn't use the MobileMe service at all. I don't want to use a totally different dynamic DNS service. I'd like to use the one I'm already paying for, or at least find out why that's not possible from Windows. Also, my primary problem is finding a network route back to my mac... once I've got that I know how to enable services so that Windows can talk to it. UPDATE: Based on some additional research, it appears that Apple is only assigning IPv6 addresses to the hostname.username.members.mac.com names. So any solution will require enabling IPv6 support on Windows, if possible.

  Read the article

• Windows Server 2008 R2 RAS VPN: access server on internal interface ip

  - by Mathias

  short question: I'm usually a linux admin but need to setup a Win2k8 R2 server for a student project. The server is running as VM on a root server and has a public internet IP assigned. Additionally I need a VPN server to access some services running on the server. I managed to set up a working VPN gateway via the Routing and RAS service which assigns clients an IP in the private subnet 192.168.88.0/24 with the Interface "Internal" listening on 192.168.88.1. Additionally I set up the external interface as NAT interface. So I can connect to the VPN server, get an IP assigned and the server additionally does NAT and I can access the internet over the VPN connection. The only thing I additionally need, is that I can access the server itself over that internal IP (e.g. client 192.168.88.2, server 192.168.88.1) as I want to access some services which I don't like to expose to the internet and restrict them to connected VPN clients. Does anybody have a hint, which configuration I'm missing here to be able to access the server over the VPN connection? EDIT: VPN clients get assigned the IP from the private subnet with subnetmask 255.255.255.255, I guess that might be the reason I can't access the server on the private IP address although it's in the same network range. Any ideas how to change this? I defined a static address pool in the Routing and RAS service, but I can't change the netmask there. EDIT2: I can't access the server from the client, but I can fully access the client from the server (ping, HTTP). I guess it has to do with firewall configuration. Thanks in advance, Mathias

  Read the article

• Upgrading Visio 2000 to Visio 2007

  - by dirtside

  I have Microsoft Visio 2000 SR 1, and recently purchased Microsoft Office Visio Standard 2007 with the understanding (supported by the product info and some other research) that I'd be able to upgrade. However, when I install 2007, it tells me it can't find a previous install of Visio, but... it's right there! Here's the exact message: "Setup can't find a version of Microsoft Office on your computer. If Office is installed on a disk or network share, click the browse button to select the appropriate disk or share... (etc.)" No matter which directory or drive I pick (various Office installs, the old Visio install, various subdirectories) it gives the following message: "The path you have chosen does not point at a qualifying upgradeable product. Click 'Retry' to try again or 'Cancel' to quit setup." Any ideas? This is a legit copy of Visio 2007 (purchased from Amazon) and the copy of Visio 2000 is legit as well. I'm not sure what exactly the installer is looking for that it would consider a "qualifying upgradeable product". A specific file?

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• Checkpoint VPN-1 R60 and Windows 7 64 Bit Client

  - by Mohit

  As per my knowledge of checkpoint VPN-1. My company is using checkpoint VPN-1 R 60 ( I guess as I dont know how to check server version) Firewall(VPN Server). Now the problem is that I installed Windows 7 64 bit. But, after my research I found that there are not even one client (SecuRemote/SecuClient) for Win7 64 bit, when Firewall or server is R60. I thought of some open source solutions. Can you guys please suggest me some with the configuration required. As of now, I know the IP of the server. I know my username and password using which I connect and that is not my domain password. that i can confirm to you guys. I am not a network guy. I am more of a developer. But, I need some help in this.So, let me know if I can provide you more details. Please please i need urgent help on this.

  Read the article

• NFS headaches with FreeBSD 4.9

  - by Ernie

  Once upon a time, this used to work, and I kept the configuration the same, but... now nothing. I'm just trying to get an NFS server set up on a FreeBSD 4.9 server. The process should be about as complicated as this: Add this entry to /etc/exports: /var/home /var/vpopmail/domains -maproot=root XXX.XX.XX.XXX Execute this: portmap nfsd -u -t -n 4 mountd -r Then this should work, regardless of network and firewall issues: showmount -e localhost But showmount -e localhost fails with the following error: RPC: Port mapper failure showmount: can't do exports rpc And even if I kill off the NFS daemon, and try a rpcinfo -p localhost, I get this error: rpcinfo: can't contact portmapper: rpcinfo: RPC: Unable to receive; errno = Connection reset by peer The portmapper is still running. Why the heck does nothing work as if it isn't? Edit to add: FYI: Sockstat gives me this: $ sockstat |egrep "(nfsd|portmap)" root nfsd 86310 3 udp4 *:2049 *:* root nfsd 86310 4 udp4 *:973 *:* root portmap 45920 0 tcp4 *:111 *:* Then, at a later time (say, 5 minutes) it's as if nfsd isn't acting as a server: $ sockstat |egrep "(nfsd|portmap)" root portmap 45920 0 tcp4 *:111 *:* But the nfs daemon is still running: $ ps ax |grep nfsd 86311 ?? I 0:00.00 nfsd: server (nfsd) 86312 ?? I 0:00.00 nfsd: server (nfsd) 86313 ?? I 0:00.00 nfsd: server (nfsd) 86314 ?? I 0:00.00 nfsd: server (nfsd)

  Read the article

• Help setting up a secondary authoritative DNS server.

  - by GLB03

  We have three Authoritative DNS servers and three recursive/caching DNS servers on my campus. Authoritative servers DNS1- Windows 2003 DNS2- Old Red Hat ----- Replacing w/ newer version DNS3- Windows 2008 (I installed) Caching and Recursive resolvers servers Server1- Windows 2003 Server2- CentOS 5.2 (I installed) Server3- CentOS 5.3 (I installed) I am replacing DNS2 with a newer Red Hat version, but have no documentation on how it was implemented. I have setup caching and windows authoritative servers, but not a linux secondary authoritative server. I have a perl script from the original server that pulls data from our DNS1 server. We use DJBDNS and TinyDNS on our linux servers. Our Network Engineer says the DNS2 server I am replacing is an authoritative server that doesn't need to be caching, but the only instructions I see is for an Authoritative server that does caching as well. Can someone point me in the right directions. I thought I was on the right track with using these instructions but when I query my new dns server I get "No response from server", I have temporarily disabled iptables to eliminate it from being an issue. ps -aux | grep dns avahi 3493 0.0 0.2 2600 1272 ? Ss Apr24 0:05 avahi-daemon: running [newdns2.local] root 5254 0.0 0.1 3920 680 pts/0 R+ 09:56 0:00 grep dns root 6451 0.0 0.0 1528 308 ? S Apr29 0:00 supervise tinydns dnslog 6454 0.0 0.0 1540 308 ? S Apr29 0:00 multilog t ./main tinydns 9269 0.0 0.0 1652 308 ? S Apr29 0:00 /usr/local/bin/tinydns

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• How to configure VirtualBox server for performance at home

  - by BluJai

  I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

  Read the article

< Previous Page | 654 655 656 657 658 659 660 661 662 663 664 665  | Next Page >