Search Results

Search found 71736 results on 2870 pages for 'how to create an access d'.

Page 665/2870 | < Previous Page | 661 662 663 664 665 666 667 668 669 670 671 672  | Next Page >

• How to boot Linux from a 16gb USB flash drive

  - by Chris Harris

  I'm trying to install Linux on a single partition of a USB flash drive that's larger than 4gb. The first place I went to is http://pendrivelinux.com. I can follow these instructions for installing Xubuntu 9.04 perfectly, which unfortunately break down when I try to scale it up beyond 4gb. There are several other tools to do this (unetbootin and usb-creator) which follow a very similar formula. I figured out that a big problem of mine was that all of these tools assume the USB drive is formatted in FAT32, which unfortunately cannot hold a single file larger than 4gb. This is unfortunate because I want to use just one partition, so that my persistance file, casper-rw, looks like one big partition to the OS once I've booted off of the USB drive. I then tried following a myriad of instructions involving formatting the drive as one large ext2 filesystem and using extlinux to create a single bootable ext2 file system. This doesn't work for me however, after about 20 attempts verifying and slightly tweaking the formula, I cannot seem to get a "good" bootable ext2 file system built. I'm not entirely sure what's going on, but it seems as though no matter how hard I try, I cannot get the ext2 file system to remain coherent after copying the Linux ISO contents over, copying the MBR, and executing extlinux to create the ext bootloader. Every time, after I follow these steps (in any order) and reboot, I get an unbootable USB drive. If I then mount the drive under Linux again, I see a mess of a file system (inodes have clearly been screwed up somewhere along the way). I suspected that the USB drive wasn't being fully flushed, so I tried using the "sync" and "unmount" commands before rebooting which didn't affect things at all. I guess I have several possible questions - but let's start with the obvious - is there something I'm missing to create a bootable ext2 USB flash drive that's large (e.g. 16gb)?

  Read the article

• VMWare Server Windows 2008 NAT Problem

  - by David

  At my new job our workstations run Windows Server 2008. However, for the specific task for which I've been hired, I need to set up a couple Linux VMs. So I grabbed the free VMWare Server and created an Ubuntu image and a Slackware image. (The former to more closely mimic the production server, the latter because I'm more familiar with it.) For desktop security purposes I need to use NAT for the network access (I would have preferred bridged, but I'm told that would go against some policy here and my whole workstation would be sandboxed from the switch). However, I can't seem to get it working right. I can ping out from the VMs to LAN addresses as well as internet addresses. I can resolve DNS names. However, attempts to use a web browser or perform any kind of higher-level interaction like that just time out. Googling around yesterday led me to various workarounds that were similar, but didn't solve my specific situation. (For example, Norton firewall blocking the connection on the host, or even the Windows firewall.) I also saw some forum posts where people said it's a known issue with VMWare and Windows Server 2008 (and Windows 7). So far I haven't been able to find a suggestion that gets me past this roadblock. I'm really not very familiar with managing a Windows Server 2008 box, so it's possible there's just some security setting somewhere that I need to modify. Does anybody have any suggestions on where I should look? UPDATE: I'm now looking at the "Network and Sharing Center" on the host workstation and it shows "VMWare Network Adapter VMnet8" (which is what I'm using) as an "Unidentified network" with "No Internet access." Looks like I can't modify ICS under the group policy. Any suggestions on how to allow this connection to have internet access?

  Read the article

• TFS 2010 : Unable to add Project to a collection

  - by Scott

  This morning I'm trying to setup Team Foundation Server 2010 to demo for my team. As this is just a demo, I thought I would install it on my Windows 7 machine which also serves as my development machine. My development machine uses Visual Studio 2008 Team Suite. I installed Team Explorer 2008 and then reapplied SP1. Finally I installed and setup TFS 2010. TFS by default gave me administrator privileges. I started up Visual Studios, and connected up to the Collection just fine. However, I'm unable to create a new project and get the follow error message: "TF30172: You are trying to create a team project either without required permissions or with an older version of team Explorer. Contact your project admin..." To check to permissions, I used my home computer which is running Visual Studio 2010. On this machine I was able to connect up to the same TFS instance and create a project no problem. So it looks as though it is a team explorer problem, but everywhere on the web people are saying not only am what I'm trying to do possible, but they have done it themselves. What am I missing to add a project to TFS 2010 under Visual Studio 2008?

  Read the article

• Cannot delete old NFS directory: Device or resource busy

  - by Jakobud

  On server1, we had an NFS share mounted from server 2 like this: /nfs/server2/share Recently, we took down server2 to install a new OS on it. Now we can't get NFS setup the way it was. When I do this: ls -l /nfs I get this: drwxr-xr-x 2 root root 0 2010-03-15 09:59 server2 Notice how the directory size is 0 instead of 4096 like usual? Anyways I go into server2 expecting to see a share directory, but I don't. It's empty. So therefore I cannot mount my share at /nfs/server2/share. When I try to create /nfs/server2/share directory, I get mkdir: cannot create directory `share': No such file or directory I think this is because it doesn't really think the /nfs/server2 directory really exists. Even if I use the -p option with mkdir, it doesn't work. Next I tried to remove /nfs/server2 so I could just recreate it. I try to rm -r /nfs/server2 but I get rm: cannot remove directory `/nfs/server2': Device or resource busy So now I'm at a loss. I need to mount this NFS share in the same exact place on server1 (at /nfs/server2/share) because other software on server1 depend on this. But if I can't create that share directory and I can't remove that directory, what do I do? Also, just for testing, I attempted to mount the share at /nfs/testing/share and it mounted just fine. But like I said, I need to mount it back in the same location.

  Read the article

• SSH Tunnel for Remote Desktop via Intermediary Server Part II

  - by Mihai Todor

  I asked previously how to configure 2 SSH tunnels using an intermediary server in order to run Remote Desktop through them and I managed to make it work. Now, I'm trying to do the same, using the same machines, but in reverse order. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, on which I wish to do Remote Desktop from the PC. I use Putty on the laptop to create a reverse tunnel from it to the Linux server: R60666 localhost:3389. I use Putty on the PC to create a regular tunnel from it to the Linux server: L60666 localhost:60666. I SSH to the Linux sever and I run telnet localhost 60666 and it seems to produce the expected output, as described in the debugging tips that I received here. I try to connect Remote Desktop from the PC to the laptop: localhost:60666. It asks for my username and password, I click OK and it locks my current session on the laptop (so I see the welcome screen on the laptop instead of my desktop), it shows the "Welcome" message in the Remote Desktop screen and then it just goes black. It doesn't disconnect, it doesn't provide any error and I'm not able to perform any actions in the Remote Desktop screen. I tried the same setup with a Windows XP laptop and I'm experiencing the same symptoms. I also tried to use different ports than 60666, but nothing changed. Does anybody have any idea what I'm doing wrong? Update: As pointed out by @jwinders, I'm not able to run telnet PC 3389 from the Linux server directly. Since Windows Firewall has a rule to allow all connections on port 3389, I have no idea what is blocking it. Fortunately, I'm able to create a SSH tunnel from the Linux machine to the PC ssh 3389:localhost:3389 'domain\user'@PC.

  Read the article

• Giving Select Windows Domain Users Symbolic Link Privilege

  - by fp0n

  I would like to setup select users on our domain to have the ability to create symbolic links on local NTFS drives and network shares without needing to run as Administrator, as part of an application with will call the CreateSymbolicLink() API directly. The default configuration for our users is to be Administrator of their computer and I think I am fighting UAC to make the privileges work the way that I want because of that. I found this link on MSDN: http://social.msdn.microsoft.com/Forums/en-SG/windowssdk/thread/fa504848-a5ea-4e84-99b7-0eb4e469cbef which describes the interaction between the SeCreateSymbolicLinkPrivilege, UAC and a domain but really does not have a solution. Here's the three options I've come up with: 1) Create a new group, give the SeCreateSymbolicLinkPrivilege to the group and assign users to the group 2) Give each individual user (2 now, more later) the privilege 3) Give the privilege to the default User group which opens it up to all Users 4) Change config so Users are not Admins by default (probably would work but not likely) Based on my testing, only 3 works for me and that is the least desirable but I've only got a local server to test with, not a domain. I need to recommend to the admin how to set this up and also have something that we can easily explain to other users of our application that are on their own domain or not on a domain. The other option seems to be to create a Service that runs with a SYSTEM account that creates the links for the application but I'd rather not go that route. Thanks.

  Read the article

• MultiPath configuration on RHEL5 and Clariion CX-300

  - by Kamil Z

  I have problem with discovering my FC-connected CX-300 storage. Frankly speaking I'm complete novice in FibreChannel, so step by step explanation would be appreciated. My configuration consist of two IBM HS20 blades with RHEL5.4 on board and 2x Qlogic ISP2422-based 4Gb Fibre Channel HBAs on each blade. As a FC switch there are two Brocades built in BladeCenter Chassis, and finally there is EMC Clariion CX-300. CX300, and Brocade switches should be configured properly, because they were working fine with previous configuration, which main defference was RHEL3 instead RHEL5.4 Below there is my output from several usefull commands: #lspci | grep Fibre 06:01.0 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) 06:01.1 FibreChannle: Qlogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) #lsmod | grep qla qla2xxx 1084741 0 scsi_transport_fc 37577 1 qla2xxx scsi_mod 141717 10 scsi_dh,qla2xxx,sg,scsi_transport_fc,usb_storage,libata,mptspi,mptscsih,scsi_transport_spi,sd_mod #cat /proc/scsi/scsi Attached Devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: LSILOGIC Model: 1030 IM IM Rev: 1000 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 Host: scsi0 Channel: 01 Id: 00 Lun: 00 Vendor: IBM-ESXS Model: ST936701LC FN Rev: B418 Type: Direct-Access ANSI SCSI revision: 04 I'd followed instructions from this site (editing /etc/multipath.conf), but i failed after multipath -ll - the output was empty. Do you have any suggestions about discovering FC Connected LUNs in such configuration?

  Read the article

• Problems configuring DB2 CLI/ODBC System DSN ODBC Data Source Administrator

  - by Komyg

  I am trying to create a System DSN ODBC connection to a DB2 9.5 database, but I am getting a very strange problem. I've looked through the internet and found the following page that has some instructions on how I should proceed: http://www.ryslander.com/how-to-install-and-configure-db2-odbc-driver/. I followed these instructions and I am able to create a new System DSN, however when I try to configure it it seems as if my configurations don't work at all. For example, when I click on the "Configure" button on my System DSN and I add a TCP/IP protocol configuration on the "Advanced Settings" tab and click "Ok", no errors appear, but when I click on "Configure" again my TCP/IP setting has vanished. This happened to all my other configurations, such as database name, username, password etc. Could you help me figure out what I am doing wrong? Note: my user is in the administrator group and I am using a Windows Server 2008 R2 Enterprise x64. UPDATE I managed to create a User DSN and connect to the database. However the problem with the System DSN remains.

  Read the article

• Windows NT from vmware to kvm

  - by Luca Rossi

  I'm trying to convert a couple of old Windows NT virtual servers from vmware to KVM. I tried almost all guidelines and how to I found around the web but with no luck. I have the vmware virtual disk: Dlc1.vmdk partitioned image. I converted the vmdk into qcow2 image with the qemu utility and I tried to use it with kvm: kvm -hda test.qemu -vnc :1 -m 750 but I receive "error loading operating system" I also tried with raw partitions I can mount through losetup and kpartx. but nothing changed I also tried to create an brand new image file with: qemu-img create -f qcow2 test.qcow2 2G I partitioned the new image file and I copied the original partition 1 to the new partition 1 with dd: dd if=/dev/mapper/loop1p1 of=/dev/mapper/loop0p1 bs=128M no luck again I also tried with a single unpartitioned file: qemu-img create -f qcow2 test.qcow2 2G and I copied the partition 1 to the new image file: dd if=/dev/mapper/loop0p1 of=test.img bs=128M but when booting, I receive a black screen and the virtual machine hangs. The bootloader is loaded successfully, because I also tried with a GRUB live iso and I receive the same screens and errors. Note that grub sees the Windows setup and give me the boot choice. I have the suspect the problem is that the vmware machine is probably a scsi guest and in centos 6 (my system) scsi emulation is no longer supported. But in that case, where to change in Windows? I'm not so skilled with MS systems. Thank you for the help Luca Rossi

  Read the article

• Modem doesn't seem to pass internet connection to router

  - by Vian Esterhuizen

  I was supplied a Cisco DPC3825 modem by my ISP and use a Cisco E4200 as my main router. Today the Internet just stopped working, just out of the blue, I can't think of anything that would have triggered it. It's been working pretty good for the past month except for a few random blips here and there. After some trouble shooting I realized that a direct wired connection to the modem would get me Internet access but if I was wired to the router as I was before I would have no connection. Assuming it was router I connected a TP-Link WR841N but it had the exact same problem. Also, connecting to the router via Wi-Fi from multiple devices will connect me to the router but I still can't get access to the Internet. From these test, it seems that the modem just won't send Internet through to the router but is clearly connecting and able to directly connect to my PC. What I've Tried A full reset and factory reset on the E4200 A full reset on the modem (but I believe my ISP has remote access to the modem because the passwords and so on are always set back). My ISP has remotely reconfigured the modem What I Should Try What else can I try? What should I do to try to narrow down the issue? Can you figure out what the problem might be based on this information?

  Read the article

• DCOM configuration: accounts with same name but different passwords problem

  - by archimed7592

  Hello, everybody! I'm experiencing troubles with DCOM configuration. Here is the case: I'm using some product which supports client-server interaction through DCOM, but the client won't get any access to the server if the attempt is being done from an account with a name which exists at the server as well, but has different password. Basically, if we try to access the server from the Administrator account which obviously present on the server machine, we will fail if client's Administrator password doesn't match server's one. After actively collaborating with the product's developer in attempts to localize the issue, he come across with resolution "can't be fixed" or, if you prefer to call a pikestaff a pikestaff than it's more likely a "don't know how to fix" resolution :). I believe there is a solution for this problem and I'm asking you, IT professionals, to help me out with this one. I do realize that the problem may be caused by the way the developer interact with DCOM and if so it can't be fixed be means of pure system configuration and the question should be asked at SO, but since I've bumped into the same behavior while working with file/printer sharing - Windows tried to simplify everything and used currently impersonated credentials to access the share, I hope the solution lies at system configuration layer. P.S. I believe that the actual software product I'm talking about is entirely irrelevant however my experience tell me that there always would be somebody who will think that it on the contrary is very relevant. Here it is: SpRecord.

  Read the article

• Getting AWStats to work in Ubuntu 12.04

  - by koogee

  I'm new to apache and i'm trying to set up AWStats on my ubuntu 12.04 server. I've followed the guide at Ubuntu docs https://help.ubuntu.com/community/AWStats I set it up according to the instructions and awstats is able to generate initial stats from apache log successfully. I placed the links to awstats in the default virtual host file. However when I try to run http://server-ip-address:8080/awstats/awstats.pl, I get: Error: SiteDomain parameter not defined in your config/domain file. You must edit it for using this version of AWStats. Setup ('/etc/awstats/awstats.conf' file, web server or permissions) may be wrong. Check config file, permissions and AWStats documentation (in 'docs' directory). Here is my /etc/apache2/sites-available/default file: <VirtualHost *:8080> ServerAdmin webmaster@localhost DocumentRoot /home/saad/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /home/saad/www/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> Alias /awstatsclasses "/usr/share/awstats/lib/" Alias /awstats-icon "/usr/share/awstats/icon/" Alias /awstatscss "/usr/share/doc/awstats/examples/css" ScriptAlias /awstats/ /usr/lib/cgi-bin/ Options ExecCGI -MultiViews +SymLinksIfOwnerMatch ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> The only three variables I edited in /etc/awstats/awstats.conf are: LogFile="/var/log/apache2/access.log" SiteDomain="server-name.noip.org" HostAliases="localhost 127.0.0.1 server-name.no-ip.org" The apache server works fine and i'm able to access other pages stored on the server. Any guidance would be welcome.

  Read the article

• HP ProCurve & Cisco switches interoperability

  - by Kamil Z

  I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below there are some details of my configuration: # m_management_2 interface FastEthernet0/43 switchport access vlan 250 switchport mode access spanning-tree port-priority 32 spanning-tree cost 100 # MTA2-swmgmt1 vlan 1 name "DEFAULT_VLAN" untagged 1-48 ip address 10.10.249.190 255.255.255.128 exit # MTA2-swtr1 vlan 1 name "DEFAULT_VLAN" untagged 1-14,16-48 no ip address no untagged 15 exit vlan 100 name "MTA Mgmt" untagged 15 ip address 10.10.249.188 255.255.255.128 exit # MTA2-swtr2 vlan 1 name "DEFAULT_VLAN" untagged 1-14,16-48 no ip address no untagged 15 exit vlan 100 name "MTA Mgmt" untagged 15 ip address 10.10.249.189 255.255.255.128 exit I don't post MTA2-bcsw[12] configuration, because I wasn's successfull in this one yet. Every time I configure VLANs on MTA2-bcsw[12] Fa0/24 interface on m_management_2 goes down bacause of receiving tagged BPDUs on access port (there are no VLANs configured on MTA2-swmgmt1 because of fact that only 250 VLAN is allowed in this switch. Is it correct?). Can someone provide me some basic configuration for this topology? Second thing I want to ask is concept of connection from MTA2-swmgmt1 to MTA2-swtr[12] HP switches for the sake of management. How to configure such ports on HP switches (managed switch and manager switch). Is my actual configuration correct?

  Read the article

• IIS6.0 asking for credentials after MS Updates

  - by Adam M.

  We have an IIS6.0 Server running on a Windows 2003 Server. Last weekend it went though maintenance, and updated a quite a few Windows updates, it is now brought up to current updates (as of March 29th). Previous to these updates we could connect to the Web page via the hostname or via a alias (there is a DNS and a WINS alias (the alias is the same name in both) that are both pointing to the system). Now since the updates it asks for credentials to access the page, when trying to access the page via IP, or by name. If you use the alias it will go right into the page. I had added a new alias in DNS and tried to access it via this name with the same effect. So it appears that the WINS alias allows the page to show up properly. I have seen this KB but http://support.microsoft.com/kb/871179 though not sure if it really is relevant to this issue. As it does refer to the 3 strikes rules to display the 401.1 error. The IIS Application pool is running under a domain account. Teh default page is allowing Anonymous login under a local account. Any thoughts? Thanks Adam

  Read the article

• "chown mysql:mysql /data/tmp" command

  - by Mellon

  I am on a Linux ubuntu machine with MySQL installed. If there is a MySQL installation on a Ubuntu machine, I saw some people doing the following thing: sudo chown mysql:mysql /data/tmp I get confused, I know the meaning of the above command, which is to change the owner of /data/tmp to user 'mysql' and change the group of it to 'mysql' group. But (my questions): 1. Why would one run the above command? If I create a table in my_db database, by default, there will be .frm, .MYD, and .MYI files (data files) be created automatically by MySQL under /var/lib/mysql/my_db/ . So, does the above command changes the default MySQL data directory to /data/tmp/ instead of /var/lib/mysql/my_db/? Basically, I would like to know the purpose and effect of the above command. (better with examples) 2. Where does the 'mysql' owner and group come from? Does the installation of MySQL on a Linux machine automatically create the 'mysql' user and group? or People need to manually create a mysql account for the linux machine?

  Read the article

• How does a vsftpd server work and how to configure it?

  - by ysap

  I was asked to configure a FTP server, based on the vsftpd package. The server is running on a remote machine to which I have a superuser privilege access. Being unfamiliar with the mechanics of FTP servers, I tried to figure out how user ftp accounts are configured. The previous maintainer used a shell script, which works on a list that we maintain to track users accounts and passwords, to configure the ftp accounts. From reading the script, I see that he generates a list of usernames and passwords, and actually creates a user account on the Linux machine. This means that for each user that we configure in the list, a new user account is being added by the adduser command: adduser --home /home/ftp --no-create-home $user (but w/o a private /home/username directory - using the /home/ftp instaed). Each of these users can log into his account using the ssh command. This fact seems a little strange to me, as I'd think that the ftp account should be decoupled from the Ubuntu user accounts. As another side effect, when a user connects using a web browser, he is connected to the /home/ftp directory. However, he can then use "Up to a higher level directory" link to go up and effectively have access to all of our system. So, the questions are: Is this really how the FTP server supposed to work in terms of configuring ftp accounts? If not, how do I configure the vsftpd server in a way that I have only the superuser Ubuntu account on that machine and all ftp account are... just FTP user accounts? Additionally, these ftp account should be configured in terms of how and what they are allowed to access.

  Read the article

• Using GitOAuthPlugin for Jenkins - not working as expected

  - by Blundell

  I need some clarity and maybe a fix. I'm using this plugin to authorise who views our Jenkins ci server: https://wiki.jenkins-ci.org/display/JENKINS/Github+OAuth+Plugin As I understand it anyone who is auth'd to view one of our github project's can also login to our Jenkins box. This works I thought it would also allow the person logging in to only view the Project that they have GitHub permission on. For instance. Three projects on GitHub (A,B,C). Three builds on Jenkins. User 1 has Git access to all 3 projects (A B C). User 2 has Git access to only 1 project (A). When logging into Jenkins: User 1 can see all 3 projects ( this works ) User 2 can only see project A The problem is User 2 can also see all 3 projects when they should only see 1! Have I got this correct, and if so is this a bug? I have the settings set in Jenkins configuration Github Authorization Settings. Here we have some admin users. One organization. And none out of the 4 checkboxes ticked. (User 2, is not an admin, is not part of the org). The plugin is open sourced here: https://github.com/mocleiri/github-oauth-plugin I was trying to get Jenkins to print me the Logs from the plugin but I also failed at viewing these (to see if there was an issue). I followed these instructions: https://wiki.jenkins-ci.org/display/JENKINS/Logging It's the same concept as outlined below but using GitHub rather than manually selecting users: https://wiki.jenkins-ci.org/display/JENKINS/2012/01/03/Allow+access+to+specific+projects+for+Users%28Assigning+security+for+projects+in+Jenkins%29 Have I got this right or wrong? Is it possible to auth a Jenkins user to only see one project?

  Read the article

• WAMP vhost issues with all vhost pointing to the first vhost statement

  - by Rick

  I am trying to setup vhosts in WAMPSERVER and I am running into an issue where all sites are pointing to the first vhosts and not delegating properly. Has anyone had this issue? Here is my setup. In windows hosts file: 127.0.0.1 siteabc.local 127.0.0.1 sitexyz.local In httpd-vhosts.conf: <VirtualHost 127.0.0.1> DocumentRoot "C:\Users\Rick\Documents\Projects\siteabc" ServerName siteabc.local ErrorLog "logs/siteabc-error.log" CustomLog "logs/siteabc-access.log" common <Directory "C:\Users\Rick\Documents\Projects\siteabc"> Options Indexes FollowSymLinks AllowOverride all Order Deny,Allow Allow from all </Directory> </VirtualHost> <VirtualHost 127.0.0.1> DocumentRoot "C:\Users\Rick\Documents\Projects\sitexyz" ServerName sitexyz.local ErrorLog "logs/sitexyz-error.log" CustomLog "logs/sitexyz-access.log" common <Directory "C:\Users\Rick\Documents\Projects\sitexyz"> Options Indexes FollowSymLinks AllowOverride all Order Deny,Allow Allow from all </Directory> </VirtualHost> <VirtualHost 127.0.0.1> DocumentRoot "C:\Users\Rick\Documents\Projects" ServerName localhost ErrorLog "logs/localhost-error.log" CustomLog "logs/localhost-access.log" common <Directory "C:\Users\Rick\Documents\Projects"> Options Indexes FollowSymLinks AllowOverride all Order Deny,Allow Allow from all </Directory> </VirtualHost> Ok so from this setup going to siteabc works...but going to sitexyz, it still goes to siteabc. Not sure what I did wrong here. Thanks for looking.

  Read the article

• Vmware Player 3.0 - cannot ping 32 bits guest from 64 bits (guest or host)

  - by npmj

  I'm stuck with what seems a bug in VmWare Player (build 203739). I'm using W7 Ultimate 64bits as host and have a CentOS 5.4 (64 bits) as a guest and a Windows XP Professional SP3 (32 bits) as another guest. From the 64 bits machines (the host and the linux guest) I cannot ping the windows XP. Off course, I already turned off the windows firewall in the guest and also in the host. The network is pretty basic, I'm using Vmnet8 (NAT), with DHCP and port forwarding (to the windows XP's IP). Everything is working ok, I have internet access from host and from both guests. Port forwarding to the XP guest is working ok too. The only problem is that I cannot access the XP guest through the Vmnet8. I monitored the traffic using wireshark (in the host and in the windows guest). If I try to ping the XP guest from the host, what I see is the ARP request leaving the host, being answered by the guest and, after that, there is no echo request leaving the host. The same occurs if I try to ping the XP from the CentOs guest. From the windows XP guest I can ping both the host and the CentOs guest. From the XP guest I can access the host shares. Obviously, from the host I cannot see the XP shares (as I cannot even ping the guest). I want to maintain this setup (using NAT to share the host's internet connection). Any suggestions?

  Read the article

• administrator user unable to login, suspicious user accounts "sky$", "admin$"

  - by mks

  I have a Windows 2008 R2 Standard (64 bit) running in a virtual machine. Suddenly from yesterday onwards I am not able to login as administrator. Nobody changed the password. Both in the console as well as using remote desktop I am unable to login. Whenever I login as Administrator I am getting this error: "The user name or password is incorrect" Nothing has changed in the machine and I have logged in the past successfully both through console and via remote desktop several time on the same machine. One strange behaviour I noticed is, I am seeing some additional user accounts if I try to login as other user. The suspicious user account are: sky$ admin$ SUPPORT_388945a0 Is it created by some malware/virus? Or is it some windows hidden account? Microsoft site says that SUPPORT_388945a0 is: The Support_388945a0 account enables Help and Support Service interoperability with signed scripts. This account is primarily used to control access to signed scripts that are accessible from within Help and Support Services. Administrators can use this account to delegate the ability for an ordinary user, who does not have administrative access over a computer, to run signed scripts from links embedded within Help and Support Services. These scripts can be programmed to use the Support_388945a0 account credentials instead of the user’s credentials to perform specific administrative operations on the local computer that otherwise would not be supported by the ordinary user’s account. When the delegated user clicks on a link in Help and Support Services, the script executes under the security context of the Support_388945a0 account. This account has limited access to the computer and is disabled by default. However I am not sure from where this "admin$" and "sky$" came. Anyone has similar experience?

  Read the article

• gpfs: adding a new nsd server to a cluster

  - by alessandra

  I have a gpfs cluster composed by 10 linux nodes, managed by a primary server A, which also act as nsd server for a first stack of disks. I attached a new jbod to one of the nodes (call it node B), which I would like to become a nsd server for this new stack of disks, but still be included in the cluster so that the disks are available to all the nodes. Node B is connected to the cluster via ethernet. How can I make the new nsd seen by all the nodes of the cluster? I can create the new nsd but when trying to create the filesystem on node B it the command mmcrfs times out. It looks like the nodes of the cluster cannot understand the filesystem location even if I specify them attached to server B in the description file. Would it be better to remove node B from the cluster, create a cluster on its own with its attached filesystem and connect it remotely with the previous cluster? Or a clustered NFS solution would apply better? Can you please give me any suggestion?

  Read the article

• Issues resolving DNS entries for multi-homed servers

  - by I.T. Support

  This is difficult to explain, so bear with me. We have 2 domain controllers, each multi-homed to straddle 2 internal subnets, (subnet A and subnet B) and provide dns, dhcp, and ldap authentication. Both domain controllers each have 2 DNS entries. both entries have identical host names, but correspond to subnet A & subnet B respectively (example entries shown): dc1 host 192.168.8.1 dc1 host 192.168.9.1 dc2 host 192.168.8.2 dc2 host 192.168.9.2 We also have a 3rd subnet for our dmz, (subnet C) which neither domain controller has an IP address on, but our firewall/routing tables provide access to subnet A from subnet C and vice versa, but don't allow access to subnet B from subnet C. Here's my issue. How can I force/determine which dns entry is used when a server on subnet C queries either domain controller by host name? Right now it seems to randomly pick one of the two entries, swaps out the name for the IP address and that's that. The problem is if it randomly selects the entry that corresponds to the 9.x subnet B (no access from subnet C), then the server fails to resolve. If it picks the entry for the 8.x subnet A then it resolves (firewall/routing tables defined for communication between these 2 subnets) Here's what I'd like to know: What are Best Practices (if any) for dealing with DNS resolution on subnets that the DNS servers don't have a presence on? Can I control something akin to a metric value to force an order of DNS resolution when there are multiple entries for the same host name that correspond to different IP subnets? Should I even have 2 DNS HOST entries for the same name? Here's what I'd like to avoid: Making edits to the HOSTS files of servers on subnet C to force DNS resolution of the hostname to the appropriate subnet Adding NIC's to the DC's to have them straddle the DMZ as well, thus obtaining a third DNS entry that corresponds to subnet C Again, my apologies if this was too verbose / unclear. Thanks!

  Read the article

• SSL on local sub-domain and sub-sub-domain

  - by Eduard Luca

  I have both local.domain.com and lmarket.local.domain.com pointing to my localhost from etc/hosts. The problem is that I am using XAMPP on Windows 7, and have 2 SSL VirtualHosts in my apache config, but no matter which one I access, I am taken to local.domain.com. On non-HTTPS requests all works fine, and the vhosts are basically the same. Here is the relevant part of my vhosts: <VirtualHost local.domain.com:443> DocumentRoot "C:/xampp/htdocs/local" ServerName local.domain.com ServerAdmin webmaster@localhost ErrorLog "logs/error.log" <IfModule log_config_module> CustomLog "logs/access.log" combined </IfModule> SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile "conf/ssl.crt/server.crt" SSLCertificateKeyFile "conf/ssl.key/server.key" <FilesMatch "\.(cgi|shtml|pl|asp|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "C:/xampp/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch ".*MSIE.*" nokeepalive ssl-unclean-shutdown downgrade-1.0 force-response-1.0 CustomLog "logs/ssl_request.log" "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> <VirtualHost lmarket.local.domain.com:443> DocumentRoot "C:/xampp/htdocs/lmarket.local" ServerName lmarket.local.domain.com ServerAdmin webmaster@localhost ErrorLog "logs/error.log" <IfModule log_config_module> CustomLog "logs/access.log" combined </IfModule> SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile "conf/ssl.crt/server.crt" SSLCertificateKeyFile "conf/ssl.key/server.key" <FilesMatch "\.(cgi|shtml|pl|asp|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "C:/xampp/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch ".*MSIE.*" nokeepalive ssl-unclean-shutdown downgrade-1.0 force-response-1.0 CustomLog "logs/ssl_request.log" "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> If I invert these blocks, then the opposite happens: local.domain.com goes to lmarket.local.domain.com. Any help would be appreciated.

  Read the article

• Vmware Player 3.0 - cannot ping 32 bits guest from 64 bits (guest or host)

  - by npmj

  I'm stuck with what seems a bug in VmWare Player (build 203739). I'm using W7 Ultimate 64bits as host and have a CentOS 5.4 (64 bits) as a guest and a Windows XP Professional SP3 (32 bits) as another guest. From the 64 bits machines (the host and the linux guest) I cannot ping the windows XP. Off course, I already turned off the windows firewall in the guest and also in the host. The network is pretty basic, I'm using Vmnet8 (NAT), with DHCP and port forwarding (to the windows XP's IP). Everything is working ok, I have internet access from host and from both guests. Port forwarding to the XP guest is working ok too. The only problem is that I cannot access the XP guest through the Vmnet8. I monitored the traffic using wireshark (in the host and in the windows guest). If I try to ping the XP guest from the host, what I see is the ARP request leaving the host, being answered by the guest and, after that, there is no echo request leaving the host. The same occurs if I try to ping the XP from the CentOs guest. From the windows XP guest I can ping both the host and the CentOs guest. From the XP guest I can access the host shares. Obviously, from the host I cannot see the XP shares (as I cannot even ping the guest). I want to maintain this setup (using NAT to share the host's internet connection). Any suggestions?

  Read the article

• DD-WRT PPTP VPN problem

  - by Tobias Tromm

  I try to configure a DD-WRT as a PPTP client. The VPN Server is Windows Server 2003. This is my scenario: The Windows 2003 Server has set to give to the VPN Client the 10.0.0.81 fixed IP and to add a network route to the remote home. At the remote home I have changed the PPTP Options at DD-WRT to make the connection. The VPN connection is successfully established. ...and Windows successfully add the route to the remote home 192.168.2.X. From the remote home I can successfully access any computer from the VPN server side. The problem is when I try to access the remote home from the Server side. From Server side I only can access\ping DD-WRT ( by VPN Client IP - 10.0.0.81). What's wrong? How I need to do to be a site-to-site VPN? This is what happen when I try to tracert the remote home from local home.

  Read the article

< Previous Page | 661 662 663 664 665 666 667 668 669 670 671 672  | Next Page >