Search Results

Search found 29619 results on 1185 pages for 'android virtual device'.

Page 676/1185 | < Previous Page | 672 673 674 675 676 677 678 679 680 681 682 683  | Next Page >

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• StrongSwan + xl2tpd client timeout between 2-5 minutes

  - by Howard Guo

  I run CentOS 6.4 on Amazon EC2, using xl2tpd-1.3.1 from EPEL repository together with StrongSwan 5.0.4. I setup a simple IPSec connection: conn l2tp type=transport keyexchange=ikev1 rekey=no authby=psk leftsubnet=0.0.0.0/0 rightsubnet=0.0.0.0/0 compress=yes auto=add And here is xl2tpd.conf: [global] ipsec saref = yes [lns default] ip range = 192.168.0.2-192.168.0.250 local ip = 192.168.0.1 ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes Here is options.xl2tpd: ms-dns 8.8.4.4 auth lock debug proxyarp There is only one client - Android 4.2 Android connects successfully: Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Connection established to x.x.x.x, 59578. Local: 18934, Remote: 29291 (ref=0/0). LNS session is 'default' Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Call established with x.x.x.x, Local: 36452, Remote: 29845, Serial: -1369754322 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: pppd 2.4.5 started by howard, uid 0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Using interface ppp0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Connect: ppp0 <--> /dev/pts/0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: peer from calling number x.x.x.x authorized Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Deflate (15) compression enabled Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: Cannot determine ethernet address for proxy ARP Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: local IP address 192.168.0.1 Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: remote IP address 192.168.0.2 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 disappeared from ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] interface ppp0 activated In the meanwhile, Internet works perfectly on the Android client, the VPN connection is stable and fast. However, it always happens that within 2-5 minutes after the connection is established: Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Maximum retries exceeded for tunnel 18934. Closing. Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Connection 29291 closed to 95.91.227.224, port 59578 (Timeout) Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deactivated Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deleted Then the VPN connection is broken. So what might have gone wrong? The same L2TP service works flawlessly on iOS 7, MacOS 10.8, and Windows 7, there is no disconnection issue on those OSes. Thank you!

  Read the article

• How to make TimeMachine back up contents of any path or mounted volume

  - by Olfan

  I keep different types of data in different encrypted sparsebundle images (say, one for each client) which automatically mount upon login but can't be opened by anybody other than myself. So, after login I have a number of virtual volumes in /Volumes/ which keeps my client data both secure and organized. How do I include data inside these virtual Volumes in TimeMachine's backups, or data residing in any path on any partition/volume? I found a promising solution description at blog.eurocomp.info involving editing the com.apple.TimeMachine.plist but all I can get TimeMachine to do is backing up the sparsebundle files themselves. I want it to back up the files inside the mounted image, though - something like adding /Volumes/Client_abc/ to TimeMachine's search path. Please do not redirect my to this previous question as it doesn't solve the problem at all. Please also refrain from telling me why you think I should not want this answer as that will not solve anything either. Please lastly don't say "it can't be done" unless you can technically prove that claim.

  Read the article

• Ubuntu not installed-Please Remove installation media and close tray and press enter

  - by Ram

  I have downloaded Ubuntu 12.04.1 LTS 32 bit, burned it on DVD and tried to install it on my PC. My PC is running in Windows 7 Ultimate 32 bit mounted on the C: drive. Now I want install Ubuntu along with my Windows 7. When I boot Ubuntu through the CD, It boots and the Ubuntu install windows opens It offers "Try Ubuntu" and "Install Ubuntu". I choose "Install Ubuntu" Then I go on to install Ubuntu with Windows(First Option)-install It shows some blank screen with some lines, and says "Please Remove installation media and close tray and press enter" Then the PC restarts and runs Windows 7 same as before normally. But Ubuntu is not installed. How to solve this problem and install Ubuntu on my PC properly? Note: I am an Android Developer. So I need to install Ubuntu for my Android Development purpose.

  Read the article

• Making lighttpd redirect from www.exampe.com to www.example.com/cgi-bin/index.pl

  - by jarmund

  What the title says.. www.example.com is defined in lighttpd.conf as a virtual host: $HTTP["host"] =~ "(^|\.)example.com$" { server.document-root = "/usr/www/example.com/http" accesslog.filename = "/var/log/www/example.com/access.log" $HTTP["url"] =~ ".pl$" { cgi.assign = (".pl" => "/usr/bin/perl" ) } } However, instead of going by the files listed in index-file.names (the usual index.html, default.html, etc), i want all requests to the root of the virtual host to be forwarded to /cgi-bin/index.pl. What's the easiest/best way of doing this? This need is a special case, and will only apply to this virtualhost. Is it possible to have that particular virtualhost send a redirect in the header?

  Read the article

• Virtualbox and Serial Port permissions

  - by Pandincus

  I have a Windows XP Pro SP3 host machine running a Windows XP Pro SP3 guest machine. The host machine has one serial port, COM1, that I need to use in the guest machine. When I add the serial port to the guest machine and try to start it, I get the following error: Failed to start the virtual machine xxx Cannot open host device 'COM1' for read/write access. Check the permissions of that device (VERR_ACCESS_DENIED). Unknown error creating VM (VERR_ACCESS_DENIED). What are some of the things that might be causing this problem? How can I check "permissions" on a serial port?

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• LM Sensors always returning same (invalid) value for one temp sensor

  - by pkaeding

  I am trying to monitor the temp sensors on a server, and plot them using Cacti. I have lm-sensors installed and working correctly. For example, here is the output from sensors: % sensors acpitz-virtual-0 Adapter: Virtual device temp1: +26.8 C (crit = +100.0 C) temp2: +32.0 C (crit = +60.0 C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +36.0 C (high = +105.0 C, crit = +105.0 C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +42.0 C (high = +105.0 C, crit = +105.0 C) However, when I try to get this data via SNMP, I get only one sensor's temperature correctly, and another one always returns 100.000 C: % snmpwalk -Os -c public -v 1 10.8.0.18 -m ALL lmTempSensors lmTempSensorsIndex.1 = INTEGER: 0 lmTempSensorsIndex.2 = INTEGER: 1 lmTempSensorsDevice.1 = STRING: temp1 lmTempSensorsDevice.2 = STRING: temp1 lmTempSensorsValue.1 = Gauge32: 26800 lmTempSensorsValue.2 = Gauge32: 100000 So, my question is two-fold: Why is the second sensor that is returned by SNMP giving a value of 100 C (when it should be 32 C) Why are my CPU core sensors not being returned by SNMP?

  Read the article

• VMWare-Tools Installation fails on Ubuntu 11.04

  - by Ajay

  I am trying to install VMwareTools-8.4.6-385536.tar.gz (VMWare Tools) on the following operating system: Ubuntu 11.04 - Linux ubuntu 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/Linux I am using VMPlayer version 3.1.4 - build 385536 ==================================================================== After starting the installation i am getting the following errors: What is the directory that contains the init scripts? [/etc/init.d] Error opening No such file or directory ================================================ Distribution provided drivers for Xorg X server are used. Skipping X configuration because X drivers are not included. Creating a new initrd boot image for the kernel. update-initramfs: Generating /boot/initrd.img-2.6.38-8-generic Starting VMware Tools services in the virtual machine: Switching to guest configuration: done Blocking file system: done Guest operating system daemon: failed Virtual Printing daemon: done Unable to start services for VMware Tools Can somebody help in this?

  Read the article

• Building NanoBSD inside a jail

  - by ptomli

  I'm trying to setup a jail to enable building a NanoBSD image. It's actually a jail on top of a NanoBSD install. The problem I have is that I'm unable to mount the md device in order to do the 'build image' part. Is it simply not possible to mount an md device inside a jail, or is there some other knob I need to twiddle? On the host /etc/rc.conf.local jail_enable="YES" jail_mount_enable="YES" jail_list="build" jail_set_hostname_allow="NO" jail_build_hostname="build.vm" jail_build_ip="192.168.0.100" jail_build_rootdir="/mnt/zpool0/jails/build/home" jail_build_devfs_enable="YES" jail_build_devfs_ruleset="devfsrules_jail_build" /etc/devfs.rules [devfsrules_jail_build=5] # nothing Inside the jail [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# sysctl security.jail security.jail.param.cpuset.id: 0 security.jail.param.host.hostid: 0 security.jail.param.host.hostuuid: 64 security.jail.param.host.domainname: 256 security.jail.param.host.hostname: 256 security.jail.param.children.max: 0 security.jail.param.children.cur: 0 security.jail.param.enforce_statfs: 0 security.jail.param.securelevel: 0 security.jail.param.path: 1024 security.jail.param.name: 256 security.jail.param.parent: 0 security.jail.param.jid: 0 security.jail.enforce_statfs: 1 security.jail.mount_allowed: 1 security.jail.chflags_allowed: 1 security.jail.allow_raw_sockets: 0 security.jail.sysvipc_allowed: 0 security.jail.socket_unixiproute_only: 1 security.jail.set_hostname_allowed: 0 security.jail.jail_max_af_ips: 255 security.jail.jailed: 1 [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mdconfig -l md2 md0 md1 md0 and md1 are the ramdisks of the host. bsdlabel looks sensible [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# bsdlabel /dev/md2s1 # /dev/md2s1: 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 1012016 16 4.2BSD 0 0 0 c: 1012032 0 unused 0 0 # "raw" part, don't edit newfs runs ok [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# newfs -U /dev/md2s1a /dev/md2s1a: 494.1MB (1012016 sectors) block size 16384, fragment size 2048 using 4 cylinder groups of 123.55MB, 7907 blks, 15872 inodes. with soft updates super-block backups (for fsck -b #) at: 160, 253184, 506208, 759232 mount fails [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mount /dev/md2s1a _.mnt/ mount: /dev/md2s1a : Operation not permitted UPDATE: One of my colleagues pointed out There are some file systems types that can't be securely mounted within a jail no matter what, like UFS, MSDOFS, EXTFS, XFS, REISERFS, NTFS, etc. because the user mounting it has access to raw storage and can corrupt it in a way that it will panic entire system. From http://www.mail-archive.com/[email protected]/msg160389.html So it seems that the standard nanobsd.sh won't run inside a jail while it uses the md device to build the image. One potential solution I'll try is to chroot from the host into the build jail, rather than jexec a shell.

  Read the article

• Degraded RAID5 and no md superblock on one of remaining drive

  - by ark1214

  This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

  Read the article

• Hylafax and "No response to MPS"

  - by Joril

  We have an Hylafax 5.2.5 CentOS 5 installation hosted inside a Xen virtual machine. It works quite well, but now I'm in the process of upgrading/migrating it to a KVM virtual machine running Ubuntu 10.04 and Hylafax 5.5.1 (compiled from source using http://sourceforge.net/projects/hylafax/files/hylafax%20debian%20build%20files/ ) The problem I'm having is that - while receiving works fine - sending faxes is extremely unreliable, I get lots of "No response to MPS repeated 3 tries", or "Failure to transmit clean ECM image data." The line, modem and configuration files I'm using are the same as before, so I thought that it could be a KVM scheduling issue, but even setting cpu_shares to 10240 instead of 1024 doesn't change a thing... What else could I try? Here's an example log file http://pastebin.com/cN01cpEs

  Read the article

• Switching from Amazon EC2 instance-store to EBS Volume

  - by Adam

  Hi, I have an Amazon EC2 instance that is using an instance-store as its root device. It has no EBS volumes attached to it. It has a database and a running web application on it. If I understand correctly this is a bad setup as I would lose all the data on the instance if it were to reboot. I would like to correct this mistake. I'd like to move all the data on the running instance to a new EBS volume and make that new volume the root device. How do I go about doing this? Thanks!

  Read the article

• Can SATA be used to connect computers?

  - by André

  Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

  Read the article

• DNS resolution not working on Browsers but on Shell

  - by Shyam Sunder Verma

  Running dig/ping on any domain, give me correct ip. When I try to browse google.com in browser it does not work. When I pick the IP (via ping) and use it in browser, website open via IP fine. But further work does not work, because of name resolution problem. DO NOT works fine on : Ubuntu 9.10 installed in Virtual Box over Windows. Ubuntu 10.10 installed in Virtual Box over Windows. Ubuntu 9.10 installed on laptop. But Internet works fine on windows vista installed on laptop.

  Read the article

• Does IP helper forward subnet broadcasts?

  - by Eamon

  Hi, I have a device on a VLAN that uses UDP subnet broadcasts to advertise its presence to similar devices. This works fine on a single VLAN, but now I need to allow it to communicate with similar devices on a second VLAN. I thought of using the IP helper command in the router, but I am wondering if that only forwards global broadcasts (255.255.255.255)? My device sends out a subnet broadcast (e.g. 192.168.6.255) Will IP helper change the destination address to the target subnet (e.g. 192.168.7.255)? Eamon

  Read the article

• How to install audio drivers for Acer Revo nettop?

  - by CT

  I have a Acer Revo nettop. I wiped the XP Home install that came on the machine and put XP Pro on. Acer's support website would lead you to believe that this product does not exist. I know it has a NVIDIA ION LE chipset so I headed over to nvidia.com to download drivers. Ive downloaded and installed the Chipset drivers, Graphics Drivers, and HDMI audio drivers. I have no sound. Under Device Manager there is an unknown Audio Device on High Definition Audio Bus. I do not have an HDMI cable to test hdmi audio. I would just like the standard audio mini-jack output to work. Anyone know of the correct driver or a generic driver that would work? Thanks

  Read the article

• Flash player, HD videos and games are choppy

  - by Aimad Majdou

  I have a problem with flash player. HD videos from Youtube or Vimeo and flash games do not play smoothly. I'm using Flash player 11, Windows 7 Sp1, and my graphic card is Intel GMA 4500. Device Manager shows me that all drivers are installed on my computer, so i don't have any problems with drivers. When I run Google chrome, Resource Monitor shows me 15% ~ 40 % of CPU Usage and 40% used Physical Memory, but when I watch a video on Youtube or play a Flash game, the Resource Monitor shows 70% - 90% CPU Usage. Also, when I run some HD Video (Frame width : 1920, Frame height : 1080) on my computer, Device Manager shows me 80% ~ 100% of CPU Usage. before I Reinstall Windows 7, HD Videos and flash games were play smoothly I hadn't any problem with them !! I hope all these informations are enough to answer my question.

  Read the article

• SQL Server: Is it possible to prevent SQL Agent from failing a step on error?

  - by franklinkj

  I have a stored procedure that runs custom backups for around 60 SQL servers (mixes 2000 through 2008R2). Occasionally, due to issues outside of my control (backup device inaccessible, network error, etc.) an individual backup on one or two databases will fail. This causes this entire step to fail, which means any subsequent backup commands are not executed and half of the databases on a given server may not be backed up. On the 2005+ boxes I am using TRY/CATCH blocks to manage these problems and continue backing up the remaining databases. On a 2000 server however, for example, I have no way to prevent this error from failing the entire step: Msg 3201, Level 16, State 1, Line 1 Cannot open backup device 'db-diff(\PATH\DB-DIFF-03-16-2010.DIF)'. Operating system error 5(Access is denied.). Msg 3013, Level 16, State 1, Line 1 BACKUP DATABASE is terminating abnormally. I am simply asking if anything like this is possible in SQL 2000 or if I need to go in a completely different direction.

  Read the article

• How to add a new entry to fstab?

  - by Roei

  I mount a device mount /dev/xvdf /mnt/mongo and verify the mount using df-h: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 955M 6.9G 12% / tmpfs 299M 44K 299M 1% /dev/shm /dev/xvdf 20G 589M 19G 4% /mnt/mongo But now I'm trying to figure out how to make it auto mount on boot. I understand I need to add a new entry to /etc/fstab, so I perform: $ sed -i '$ a\/dev/xvdf /mnt/mongo xfs defaults 1 1' /etc/fstab But, after reboot, it seems that the auto mount didn't work. The device didn't appear in the df -h list. Should I not use the sed to add the entry? Is the entry I entered incorrect?

  Read the article

• renaming hard drives (sdc to sdb) on the fly

  - by w00t

  ata2: link is slow to respond, please be patient (ready=0) kernel: [2761026.198796] ata2: soft resetting link kernel: [2761031.226669] ata2.00: disabled kernel: [2761031.226720] ata2: EH complete kernel: [2761031.226753] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK After receiving the error above, I couldn't access /dev/sdb anymore. Not wanting to restart the server, I rescanned for the device using echo "- - -" > /sys/class/scsi_host/host1/scan and it readded the drive as /dev/sdc. From what I have found, I need to use echo "scsi add-single-device 0 0 3 0" > /proc/scsi/scsi, "3" being the SCSI ID which corresponds to sdb. Everything nice up to the point I execute the command and get -bash: echo: write error: Invalid argument. All the solutions point to using this method, but I am unable to. Any other method available? Debian 5.0.8 - 2.6.26-1-686

  Read the article

• Getting MSExchange transport Error on Server 2003 SP2

  - by Scott

  I am getting the following Error messages and do not know how to fix it. Event Type: Error Event Source: MSExchangeTransport Event Category: (8) Event ID: 3017 Date: 4/29/2010 Time: 1:21:12 PM User: N/A Computer: NETSRV Description: A non-delivery report with a status code of 5.3.5 was generated for recipient rfc822;[email protected] (Message-ID <19104335.51321272561635734.JavaMail.SYSTEM@PARROT). Causes: A looping condition was detected. (The server is configured to route mail back to itself). If you have multiple SMTP Virtual Servers configured on your Exchange server, make sure they are defined by a unique incoming port and that the outgoing SMTP port configuration is valid to avoid looping between local virtual servers. Thanks for any help you can provide.

  Read the article

• Can someone explain the "use-cases" for the default munin graphs?

  - by exhuma

  When installing munin, it activates a default set of plugins (at least on ubuntu). Alternatively, you can simply run munin-node-configure to figure out which plugins are supported on your system. Most of these plugins plot straight-forward data. My question is not to explain the nature of the data (well... maybe for some) but what is it that you look for in these graphs? It is easy to install munin and see fancy graphs. But having the graphs and not being able to "read" them renders them totally useless. I am going to list standard plugins which are enabled by default on my system. So it's going to be a long list. For completeness, I am also going to list plugins which I think to understand and give a short explanation as to what I think it's used for. Pleas correct if I am wrong with any of them. So let me split this questions in three parts: Plugins where I don't even understand the data Plugins where I understand the data but don't know what I should look out for Plugins which I think to understand Plugins where I don't even understand the data These may contain questions that are not necessarily aimed at munin alone. Not understanding the data usually mean a gap in fundamental knowledge on operating systems/hardware.... ;) Feel free to respond with a "giyf" answer. These are plugins where I can only guess what's going on... I hardly want to look at these "guessing"... Disk IOs per device (IOs/second)What's an IO. I know it stands for input/output. But that's as far as it goes. Disk latency per device (Average IO wait)Not a clue what an "IO wait" is... IO Service TimeThis one is a huge mess, and it's near impossible to see something in the graph at all. Plugins where I understand the data but don't know what I should look out for IOStat (blocks/second read/written)I assume, the thing to look out for in here are spikes? Which would mean that the device is in heavy use? Available entropy (bytes)I assume that this is important for random number generation? Why would I graph this? So far the value has always been near constant. VMStat (running/I/O sleep processes)What's the difference between this one and the "processes" graph? Both show running/sleeping processes, whereas the "Processes" graph seems to have more details. Disk throughput per device (bytes/second read/written) What's thedifference between this one and the "IOStat" graph? inode table usageWhat should I look for in this graph? Plugins which I think to understand I'll be guessing some things here... correct me if I am wrong. Disk usage in percent (percent)How much disk space is used/remaining. As this is approaching 100%, you should consider cleaning up or extend the partition. This is extremely important for the root partition. Firewall Throughput (packets/second)The number of packets passing through the firewall. If this is spiking for a longer period of time, it could be a sign of a DOS attack (or we are simply recieving a large file). It can also give you an idea about your firewall performance. If it's levelling out and you need more "power" you should consider load balancing. If it's levelling out and see a correlation with your CPU load, it could also mean that your hardware is not fast enough. Correlations with disk usage could point to excessive LOG targets in you FW config. eth0 errors (packets in/out)Network errors. If this value is increasing, it could be a sign of faulty hardware. eth0 traffic (bits/second in/out)Raw network traffic. This should correlate with Firewall throughput. number of threadsAn ever-increasing value might point to a process not properly closing threads. Investigate! processesBreakdown of active processes (including sleeping). A quick spike in here might point to a fork-bomb. A slowly, but ever-increasing value might point to an application spawning sub-processes but not properly closing them. Investigate using ps faux. process priorityThis shows the distribution of process priorities. Having only high-priority processes is not of much use. Consider de-prioritizing some. cpu usageFairly straight-forward. If this is spiking, you may have an attack going on, or a process is hogging the CPU. Idf it's slowly increasing and approaching max in normal operations, you should consider upgrading your hardware (or load-balancing). file table usageNumber of actively open files. If this is reaching max, you may have a process opening, but not properly releasing files. load averageShows an summarized value for the system load. Should correlate with CPU usage. Increasing values can come from a number of sources. Look for correlations with other graphs. memory usageA graphical representation of you memory. As long as you have a lot of unused+cache+buffers you are fine. swap in/outShows the activity on your swap partition. This should always be 0. If you see activity on this, you should add more memory to your machine!

  Read the article

• How to copy directories using debugfs?

  - by STM

  The debugfs manpage gives the impression that the command 'rdump . .' will recursively copy all files found on the specified filesystem from the debugfs cwd to the native filesystem's cwd. Instead I seem to receive a syntax error, and no copy is initiated? These are the commands I run: cd /path/to/transfer/destination debugfs /dev/sda1 -R rdump . . My task is to copy the entire contents of a clean yet unmountable USB storage device to its host machine's HD. The host machine does not support the inode size used by the USB device's filesystem (256) and its software is not upgradeable, so my intention was to use debugfs to transfer the files. If anyone has any other suggestions for this task I'd be grateful.

  Read the article

• Dropbox alternative with local sync support?

  - by srid

  I am currently using Dropbox. Just decided to sync my huge (about 5 GB) iTunes Library (music collection) in Dropbox. For that I must subscribe to their paid account. But before I do so, I'd like evaluate the alternatives. Is there an alternative that does this? Local LAN sync (eg: sync my huge music collection across computers in local network without uploading/downloading them to internet) The following would be nice (but not required): Native android client - so music will be made available in the Android music app / SDHC card Selective sync: sync particular folders / exclude certain folders on certain computers .. eg: excluding porn folder on work computers ;-) Just like Dropbox, it MUST work on 64-bit Windows, Linux and Mac. Know of any? (I am currently evaluating Spideroak. Boy, was it so complicated to use?)

  Read the article

< Previous Page | 672 673 674 675 676 677 678 679 680 681 682 683  | Next Page >