Search Results

Search found 19018 results on 761 pages for 'indicator network'.

Page 678/761 | < Previous Page | 674 675 676 677 678 679 680 681 682 683 684 685  | Next Page >

• Methods to transfer files from Windows server to linux server

  - by Raze2dust

  Hi, I need to transfer webserver-log-like-files containing periodically from windows production servers in the US to linux servers here in India. The files are ~4 MB in size each and I get about 1 file per minute. I can take about 5 mins lag between the files getting written in windows and them being available in the linux machines. I am a bit confused between the various options here as I am quite inexperienced in such design: I am thinking of writing a service in C#.NET which will periodically archive, compress and send them over to the linux machines. These files are pretty compressible. WinRAR can convert 32 MB of these files into a 1.2 MB archive. So that should solve the network transfer speed issue. But then how exactly do I transfer files to linux? I could mount linux drive on windows server using samba, or should I create an ftp server, or send the file serialized as a POST request. Which one would be good? Also, I have to minimize the load on the windows server. Mount the windows drive on linux instead. I could use the mount command or I could use samba here (What are the pros and cons of these two?). I can then write the compressing and copying part in linux itself. I don't trust the internet connection to be very stable, so there should be a good retry mechanism and failure protection too. What are the potential gotchas in these situations, and other points that I must be worried about? Thanks, Hari

  Read the article

• Trouble in Team Viewer VPN Connection

  - by Sumit Pal

  I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

  Read the article

• No LAN and SMB access, and Explorer not responsive, when using a second connection

  - by Lorenzo

  I apologize if this is a duplicate question, I know that there are several questions about multiple connection (LAN + LAN and LAN + dialup) but I haven't been able to find one that fits my scenario. I'm still using Windows XP on my corporate laptop, and I'm connected to the corporate LAN via Ethernet. The LAN NIC has a public IP address, although not accessible externally, obtained via the corporate DNS server. This connection is firewalled and requires a proxy to access Internet. To access Internet sites blocked by the corporate firewall, I use my smartphone via USB tethering. It is seen as a new LAN interface, and I get a private IP address (class 192.168..). There are two problems: The LAN is not accessible, as the default gateway goes to the tethering NIC. I'd like to solve this, but I can live with it. My PC becomes unresponsive if I use Windows Explorer to view local files, or even when I open the start menu. I guess that this is caused by attemps to connect to a mapped network drive. But I disabled the "Client for Microsoft Networks" in the tethering NIC. Why the system still hangs? Of course if I disable the Ethernet NIC, Explorer stops hanging. If you need further details, add a comment. Thanks!

  Read the article

• Finding default gateway in an openvpn environment in windows

  - by Alexander Trümper

  I need to find the default gateway in a openvpn scenario where the route output looks like that: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 0.0.0.0 128.0.0.0 10.8.0.1 10.8.0.2 30 So I googled around a bit and a found this script here: @For /f "tokens=3" %%* in ( 'route.exe print ^|findstr "\<0.0.0.0\>"' ) Do @Set "DefaultGateway=%%*" echo %DefaultGateway% This works, but matches both lines in the route output. But I need to find this line: 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 So I tried to modify the findstr parameter like this: findstr "\<0.0.0.0\>.\<0.0.0.0\>" in the expectation that '.' will match for the tab between the columns. But it doesn't. It will still set DefaultGateway to 10.8.0.1 I couldn't find a clue in MS documentation either. Maybe someone knows the right expression? Thanks a lot.

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• How do I prevent a tar pipe from causing swapping?

  - by Jeff Shattock

  I have a rather large filesystem that I need to transfer from one Linux server to another. I figured the best way to do this was via a tar/netcat pipe arrangment, something like tar c . | pv | nc blah blah blah And it works great, the network stays fairly saturated, life is good. Until the source machine starts swapping. The files are on a raid on the source system, so the read speed is much faster than the write speed on the other end. Since the dest machine hasnt picked up the data yet, the source machine needs to stick it somewhere, so into RAM it goes, until there is no more free RAM. It then starts swapping, which is horribly painful since that machine has its OS installed on a somewhat slow CF card. Both machines have 4GB of physical ram, 64 bit Ubuntu 9.04 server. GigE link between them. How do I prevent this swapping? Can I put a "speed-limit" on the tar or netcat process so that the transfer speed doesn't overwhelm the write throughput on the destination end? The man pages didn't list anything, but there might be something I'm overlooking.

  Read the article

• linux routing issue

  - by Duc To

  Hi! I have 2 linksys routers which has linux running on it and using tomato firmware.. both has internet lines plugged on but only 1 acts as DHCP server (router 1) What I am having to achieve is that all packets goes to router 1 from internal IPs want to access internet will go out to that internet line but from 1 specific port, if router 1 detects packets from a specific source port (for ex: http port: 80), it will redirect that packet to router 2 and goes out to the internet from there.. I have found some documents which give solution that I will need a linux servers with 2 ethernet cards and then we plug both internet lines on that server and routing base on it but I do not want to do that because my boss does not want to have an extra work mantaining that server, besides, he says that the router itself already a linux one so why.. I tend to agree his points.. Can it be done or a seperate linux server acting as a router is a must? Thank you all in advance and really look forward in your replies.. I am newbie to linux network and it seems to be something out of my capacity to solve :( Your sincerely! Duc To

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Ubuntu 10.04->10.10 in failed state - how to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: (1) "Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a)." (2) "gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok]" (3) "gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ..." What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• no administrator password for Windows 7

  - by huskergirl78

  I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

  Read the article

• Hardware issue, bsod with windows xp irq and strange messages with ubuntu

  - by JP Hellemons

  I have an old Acer T160 and it used to run Windows XP. But I keep getting random BSOD's. I keep seeing IRQ conflicts. I tried to run ubuntu, which runs and keeps running. But sometimes is not responding. Also there are these popups at ubuntu 12.04 that my network cable (which is onboard) is unplugged. But I have no cable in it! and have an usb dongle for wifi. which also seems unstable. have to (auto)reconnect sometimes. So my question is: is it my mobo, power supply or something else? FYI: I had an dvd-rw station which did not open properly, so unplugged the ata and power, als removed the second harddrive. now only have sata harddrive. also removed the extra video card (ati sapphire x1600 pro) so use only onboard video now and still have these issues. EDIT Update: will try with a new PSU (power supply unit of 400watt) the old (factory) one was 300watt. and will use a usb drive which has 12.04 ubuntu on it (made with unetbootin) to format everything and re-install ubuntu. (so also delete mbr partition) will update the day after tomorrow.

  Read the article

• Routing / binding 128 IPs to one server

  - by Andrew

  I have a Ubuntu server with 128 ip's (static external ips 86.xx.xx.16), and I want to crawl pages thru different ip's. The gateway is xx.xxx.xxx.1, the main ip is xx.xxx.xxx.16, and the other 128 ip's are xx.xxx.xxx.129/255. I tried this configuration in /etc/network/interfaces but I doesn't work. It work if I remove the gateway for the aliases eth0:0 and eth0:1. I think this is routing problem. auto lo iface lo inet loopback auto eth0 auto eth0:0 auto eth0:1 iface eth0 inet static address xx.xxx.xxx.16 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:0 inet static address xx.xxx.xxx.129 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:1 inet static address xx.xxx.xxx.130 netmask 255.255.255.128 gateway xx.xxx.xxx.1 Also, please tell me how to "reset" every changes that I made in networking and routing. Update: I removed the gateway and now it works. I can reach the website thru all 128 ip's. But when I try to bind a socket connection in php to a specific ip I get no answer. socket_bind($sock, "xx.xxx.xx.xxx"); socket_connect($sock, 'google.com', 80); I tryed to use a sniffer to see the packets, and I see the packet sent from binded ip to google.com but the "connection" can't be established. I don't know anything about "route" command, but I have a feeling that this is the solution.

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• How to completely disable IPv6 for loopback interface on RHEL 5.6

  - by Marc D

  I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

  Read the article

• Internal Code Signing: Key Distribution, or Certificate Server?

  - by Myrddin Emrys

  I should first note that we have nobody in IT with significant familiarity with self-signed certification. We have a moderately sprawling network (one forest, many locations), and we are now rolling out internal code signing; until now users have run untrusted code, or we even disabled(!) the warnings. Intranet applications, scripts, and sites will now be signed with self certification. I am aware of two obvious ways we can deploy this: Distributing the keys directly via a group policy, and setting up a cert server. Can someone explain the trade-offs between these two methods? How many certs before the group policy method is unwieldy? Are they large enough that remote users will have issues? Does the group policy method distribute duplicates on every login? Is there a better method I am not aware of? I can find a lot of documentation on certifications and various ways to create them, but I have not been able to find something that summarizes the difference between the distribution methods and what criteria make one or the other superior.

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• How to change mount to grant user write permissions?

  - by nals

  I am on TomatoUSB, and using the feature to have a NAS. The only way I can write to the Samba share is if I force root: [global] interfaces = 127.0.0.1, 192.168.1.1/24 bind interfaces only = no workgroup = WORKGROUP netbios name = TOMATO security = share wins support = yes name resolve order = wins lmhosts hosts bcast guest account = nobody [Public] path = /mnt/sda2 read only = no public = yes only guest = yes guest ok = yes browseable = yes comment = Network share force user = root writeable = yes I dont really like the idea having to use root to allow write access to my share. I have a samba account created already named nobody to allow access to the share. However every time I try to write I get access denied error. fstab: /dev/sda2 /mnt/sda2 vfat defaults 0 0 Further more every time I try to chmod 777 /tmp/mnt/sda2 the permissions are not changed, and no error is produced. They stay 755. drwxr-xr-x 2 root root 4096 Jun 4 01:49 sda2 Basically; how can I give the user nobody write permissions to my mount? dev name: /dev/sda2 dev mount: /tmp/mnt/sda2

  Read the article

• A little guidance setting up FTP server authentication on Windows Server 2008 R2 standard?

  - by Ropstah

  I have a (clean) server running Windows Server 2008 R2 standard. I would just like to use it for serving a website and a FTP server through IIS. IIS is installed and serves my website propery. I have now added a FTP site but when I try to logon using my user/pass i get the following error: 530 User cannot login From this article (http://support.microsoft.com/kb/200475) I understand that these four causes can be pointed out: The Allow only anonymous connections security setting has been turned on in the Microsoft Management Console (MMC). Not the case The username does not have the Log on locally permission in User Manager. The user is in the Users group, however I'm not able to logon through RDP. I tried configuring this by following this article through GPMC however this only works when I'm logged in as a domain user on a domain controller which I'm not: I'm logged in as administrator The username does not have the Access this computer from the network permission in User Manager. Not sure what this implies...? The Domain Name was not specified together with the username (in the form of DOMAIN\username). Tried adding the server name: server\username, not working... I am an absolute server noob and I'd just like to be able to connect through FTP... Any guidance is highly appreciated!

  Read the article

• Snow Leopard takes a long time to connect to Windows/Samba server

  - by hood

  We run a very heterogeneous network here: There is some XP, Vista, 7, Leopard, Snow Leopard clients, and Windows 2003 (one remaining legacy app), 2008, and Linux servers. The main file server runs Ubuntu Linux and has been added to the Windows Domain and has been used for many years; SBS 2008 is the PDC (the 2003 and 2008 are on the domain also). In Leopard there were no problems at all authenticating to the file servers. We've upgraded one of the Leopard iMacs to Snow Leopard, though the same problem occurs in a new MBP which came with the newer OS as well as a clean install on another iMac. It does not matter whether connected through wired or wireless. In the Finder when clicking on the server - whether on first boot or after it is connected - it will display "Connecting..." for up to a few minutes before either generally working (if username/password in keychain) or displaying "Connection Failed" - at which time clicking "Connect As" and typing in the username/password will take some more time and eventually work. Sometimes it will display "Connecting..." indefinitely. (I've left it as long as 15 minutes before trying something else) Accessing shares on the the 2003 and SBS servers have the problem (so I don't think it's a Samba server issue). The Server 2008 Standard is connecting instantly at the moment. Accessing the share through an alias/stacks doesn't have this problem. Leopard and Windows clients still have no problem. I've searched Google but hasn't yielded any working result. How do I get rid of this delay?

  Read the article

• apt-mirror does not mirror the i18n directory

  - by Fred

  I need to setup a local Ubuntu mirror so the whole network doesn't need to hit remote servers in order to update and install new packages. Following a brief tutorial found here, I managed to get a server up and running that correctly mirrors packages from the main and restricted categories. However, when I call apt-get update on a client, I get a couple of errors such as : Ign http://192.168.1.18 karmic/main Translation-fr Ign http://192.168.1.18 karmic/restricted Translation-fr Checking back on the server, I see that apt-mirror only took the binary-amd64 directory of the mirror, and didn't take i18n that would provide Translation-fr. The manpage for apt-mirror doesn't say anything about i18n, and Google is of no help either. How do I properly mirror i18n? My current mirror.list file is as follows : ############# config ################## # # set base_path /var/spool/apt-mirror # # if you change the base path you must create the directories below with write privileges # # set mirror_path $base_path/mirror # set skel_path $base_path/skel # set var_path $base_path/var # set cleanscript $var_path/clean.sh # set defaultarch <running host architecture> # set postmirror_script $var_path/postmirror.sh set run_postmirror 0 set nthreads 20 set _tilde 0 # ############# end config ############## deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic main restricted deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic-updates main restricted clean http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive

  Read the article

• How do I prevent my ASP .NET site from continually prompting for user credentials?

  - by gilles27

  I'm trying to get an ASP .NET website up and running on IIS6. The site will run in its own application pool, and uses Windows authentication, with anonymous access turned off. When I run the app pool under NETWORK SERVICE, everything works fine. However we need the app pool to run under a different account, because this account needs some extra privileges (we are printing Word documents). This new account is a member of the local users group, and the IIS_WPG group. It has also been granted the "Log on as a service right". When I browse to the site I am prompted for credentials, not once, but several times. When the page finally loads it looks wrong because the style sheets have not been applied. My suspicion is that I am being prompted once for each file (e.g. all the images, styles and script files) the browser requests, and that for some reason the website is unable to validate those credentials in order to serve the files back. If I allow anonymous access the page loads fine - we don't want to allow it but I mention it in case it offers any further clues. My theory is that perhaps the account the app pool runs under needs permissions to validate domain credentials? If that is so, how do I enable this?

  Read the article

• Multi- authentication scenario for a public internet service using Kerberos

  - by StrangeLoop

  I have a public web server which has users coming from internet (via HTTPS) and from a corporate intranet. I wish to use Kerberos authentication for the intranet users so that they would be automatically logged in the web application without the need to provide any login/password (assuming they are already logged to the Windows domain). For the users coming from internet I want to provide traditional basic/form- based authentication. User/password data for these users would be stored internally in a database used by the application. Web application will be configured to use Kerberos authentication for users coming from specific intranet ip networks and basic/form- based authentication will be used for the rest of the users. From a security perspective, are there some risks involved in this kind of setup or is this a generally accepted solution? My understanding is that server doesn't need access to KDC (see Kerberos authentication, service host and access to KDC) and it can be completely isolated from AD and corporate intranet. The server has a keytab file stored locally that is used to decrypt tickets sent by the users coming from intranet. The tickets only contain username and domain of the incoming user. Server never sees the passwords of authenticated users. If the server would be hacked and the keytab file compromised, it would mean that attacker could forge tickets for any domain user and get access to the web application as any user. But typically this is the case anyway if hacker gains access to the keytab file on the local filesystem. The encryption key contained in the keytab file is based on the service account password in AD and is in hashed form, I guess it is very difficult to brute force this password if strong Kerberos encryption like AES-256-SHA1 is used. As the server has no network access to intranet, even the compromised service account couldn't be directly used for anything.

  Read the article

• ssh from 1 ubuntu box to another ubuntu box

  - by michael

  Hi, I have 2 ubuntu boxes in a WiFi network. Below is the 'ifconfig' of my destination machine. But in my source machine, I tried 'ssh 192.168.1.2' I get connection refused. $ ifconfig eth0 Link encap:Ethernet HWaddr c8:0a:a9:4d:d6:6a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:35 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4508 errors:0 dropped:0 overruns:0 frame:0 TX packets:4508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:330441 (330.4 KB) TX bytes:330441 (330.4 KB) wlan0 Link encap:Ethernet HWaddr 00:23:14:32:e8:dc inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:14ff:fe32:e8dc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:319828 errors:0 dropped:0 overruns:0 frame:0 TX packets:618371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30642011 (30.6 MB) TX bytes:921522542 (921.5 MB) How to set up so that I can ssh from 1 box to another?

  Read the article

• Using Samba to share a folder from a Linux guest with a Windows host in VirtualBox

  - by AmV

  I would like to share a folder from a Linux Guest with a Windows host (with read and write access if possible) in VirtualBox. I read in these two links: here and here that it's possible to do this using Samba, but I am a little bit lost and I need more information on how to proceed. So far, I managed to set up two network adapters (one NAT and one host-only) and install Samba on the Linux guest, but now I have the following questions: What do I need to type in samba.conf to share a folder from the Linux guest? (the tutorial provided in one of the links above only explains how to share home directories) Are there any Samba commands that need to be executed on the guest to enable sharing? How do I make sure that these folders are only available to the host OS and not on the Internet? Once the Linux guest is setup, how do I access each of the individual shared folders from the Windows host? I read that I need to mount a drive on Windows to do this, but do I use Samba logins, or Linux logins, also do I use localhost? or do I need to set up an IP for this? Thanks!

  Read the article

< Previous Page | 674 675 676 677 678 679 680 681 682 683 684 685  | Next Page >