Search Results

Search found 19768 results on 791 pages for 'hardware programming'.

Page 690/791 | < Previous Page | 686 687 688 689 690 691 692 693 694 695 696 697  | Next Page >

• External HDD connecting via USB disconnects wireless LAN connection

  - by Kensai

  Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

  Read the article

• Are these hardwares compatible?

  - by Tom Kaufmann

  I am trying to upgrade my new machine but I want to do it myself. This is my 1st attempt at building system. After carefully reading reviewing feedback and my budget I have decided to select the below listed components. Can anybody let me know are they compatible or not? Transcend 64 GB 2.5" SATA Solid State Drive Asus GeForce GTX550 1GB DDR5 ENGTX550 TI DI/1GD5 Graphics Card Seagate Barracuda 1 TB HDD Internal Hard Drive Cooler Master eXtreme Power Pro 600 Power Supply Intel Core i5 2500K Sandy Bridge 3.30 GHz 95 W 4 Core Desktop Processor Intel DX79TO Motherboard Corsair CMZ8GX3M2A1600C9 8 GB DDR3 SDRAM 1600 MHz Dual Channel Kit Desktop Memory Sony AD-7260S-ZS Internal DVD Writer - Black Cooler Master Hyper TX3 EVO Intel CPU Cooler Cooler Master Elite 335U Cabinet LG E2051T 20.1 Inch SuperSlim Monitor Is any of these hardware components incompatible with I5 2500K? If you have any other suggestions for selecting any other harwdware that can boost up my performance or lower my cost while having the same performance, please suggest. But my primary questions is whether they are compatible or not! Any help is appreciated. Thank you.

  Read the article

• Does Mac OS X throttle the RATE of socket creation?

  - by pbhogan

  This may seem programming related, but this is an OS question. I'm writing a small high performance daemon that takes thousands of connections per second. It's working fine on Linux (specifically Ubuntu 9.10 on EC2). On Mac OS X if I throw a few thousand connections at it (roughly about 16350) in a benchmark that simply opens a connection, does it's thing and closes the connection, then the benchmark program hangs for several seconds waiting for a socket to become available before continuing (or timing out in the process). I used both Apache Bench as well as Siege (to make sure it wasn't the benchmark application). So why/how is Mac OS X limiting the RATE at which sockets can be used, and can I stop it from doing this? Or is there something else going on? I know there is a file descriptor limit, but I'm not hitting that. There is no error on accepting a socket, it's simply hangs for a while after the first (roughly) 16000, waiting -- I assume -- for the OS to release a socket. This shouldn't happen since all prior the sockets are closed at that point. They're supposed to come available at the rate they're closed, and do on Ubuntu, but there seems to be some kind of multi (5-10?) second delay on Mac OS X. I tried tweaking with ulimit every-which-way. Nada.

  Read the article

• Does Mac OS X throttle the RATE of socket creation?

  - by pbhogan

  This may seem programming related, but this is an OS question. I'm writing a small high performance daemon that takes thousands of connections per second. It's working fine on Linux (specifically Ubuntu 9.10 on EC2). On Mac OS X if I throw a few thousand connections at it (roughly about 16350) in a benchmark that simply opens a connection, does it's thing and closes the connection, then the benchmark program hangs for several seconds waiting for a socket to become available before continuing (or timing out in the process). I used both Apache Bench as well as Siege (to make sure it wasn't the benchmark application). So why/how is Mac OS X limiting the RATE at which sockets can be used, and can I stop it from doing this? Or is there something else going on? I know there is a file descriptor limit, but I'm not hitting that. There is no error on accepting a socket, it's simply hangs for a while after the first (roughly) 16000, waiting -- I assume -- for the OS to release a socket. This shouldn't happen since all prior the sockets are closed at that point. They're supposed to come available at the rate they're closed, and do on Ubuntu, but there seems to be some kind of multi (5-10?) second delay on Mac OS X. I tried tweaking with ulimit every-which-way. Nada.

  Read the article

• Failed Software RAID0 on Linux - Attempting to recover data

  - by Gizmo_the_Great

  I have a two disk RAID0 software raid (not hardware raid) that is reported to have failed during boot and my OS won't start. Using a Live CD, I get the following output : sudo mdadm -E /dev/sdc1 /dev/sdd1 /dev/sdc1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 1465145328 (698.64 GiB 750.15 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : ad427cd2:9f885f57:7f41015f:90f8f6af Update Time : Sun Jun 8 12:35:11 2014 Checksum : a37407ff - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) /dev/sdd1: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : 3710713d:fb301031:84b61247:d1d53e0f Name : HP-xw9300:0 Creation Time : Sun Sep 1 15:22:26 2013 Raid Level : -unknown- Raid Devices : 0 Avail Dev Size : 976771056 (465.76 GiB 500.11 GB) Data Offset : 16 sectors Super Offset : 8 sectors State : active Device UUID : 2ea0199d:cb08d9e7:0830448a:a1e1e348 Update Time : Sun Jun 8 13:06:19 2014 Checksum : 8883c492 - correct Events : 1 Device Role : spare Array State : ('A' == active, '.' == missing) GParted lists both disks, detects the flags as 'Raid' and lists the data usage. Can anyone please help me re-assemble just so that I can copy some of the data off that I have not backed up recently? Thanks

  Read the article

• Ubuntu 12.04 VirtualBox on powerful W7 quite slow

  - by wnstnsmth

  I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

  Read the article

• Server specification recommendation

  - by foo

  To cut the story short, I can't buy an item (server/cpu/motherboard/ram) that costs more than USD 330. However, I can combine them, meaning, I can buy a CPU that costs USD 330 and motherboard that costs USD 330. With this limitation, I can't buy a powerful 1U server which will definitely costs me more USD 330. With that in mind, I was hoping to build a powerful desktop PC which will be used as a database server. However, through my experience, desktop PC doesn't last very long, usually the motherboard will just die by itself after 1 or 2 years. So, what would you guys recommend me to buy with this kind of budget? Every item must be <= USD 330. Will be used as a MySQL server. RAID would be nice. 1TB is pretty big for my data. I do not need external graphic card (onboard would do just fine), mouse, keyboard, monitor. Linux friendly. One ethernet port is good enough. It's important that those hardware is made of components that will last long (at least 3 years or something). The server will be placed in an air conditioned room, but a good ventilation for the server is always preferred. I won't overclock it. Intel processor is preferred. Thanks in advance.

  Read the article

• Cisco 7206vxr cpu reducing

  - by naimson

  I have a 7206VXR (NPE-G2) . At the rate of 140 kpps i gain 80% of cpu . So i looking for ways how to reduce it? So i want to turn off netflow(but don't want to this,monitoring is highly important for me), but it will give me only 10-20% ? At this moment with 84kpps i have 58% sh processes cpu sorted give me this. PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 109 163534600 537236763 304 35.38% 32.83% 16.85% 0 IP Input 67 829396 52280 15864 0.15% 0.01% 0.00% 0 Per-minute Jobs 68 5542736 3053476 1815 0.15% 0.18% 0.16% 0 Per-Second Jobs 51 635852 1116315 569 0.07% 0.03% 0.02% 0 Net Background 329 120396 4607274 26 0.07% 0.00% 0.00% 0 EIGRP-IPv4 Hello 105 50508 95032488 0 0.07% 0.05% 0.05% 0 IPAM Manager 6 4068580 476916 8531 0.00% 0.07% 0.05% 0 Check heaps 7 7768 3634 2137 0.00% 0.00% 0.00% 0 Pool Manager 8 0 1 0 0.00% 0.00% 0.00% 0 DiscardQ Backgro 10 8 708 11 0.00% 0.00% 0.00% 0 WATCH_AFS 5 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers 12 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea 9 0 2 0 0.00% 0.00% 0.00% 0 Timers 11 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio 13 296 610532 0 0.00% 0.00% 0.00% 0 IPC Event Notifi 16 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager 17 3584 2980311 1 0.00% 0.00% 0.00% 0 IPC Periodic Tim 4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN 19 0 1 0 0.00% 0.00% 0.00% 0 IPC Process leve 20 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager 21 96 174453 0 0.00% 0.00% 0.00% 0 IPC Check Queue 14 4 50890 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach 3 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ 24 756 305371 2 0.00% 0.00% 0.00% 0 IPC Keep Alive M 25 2340 610561 3 0.00% 0.00% 0.00% 0 IPC Loadometer 22 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat RX Cont 15 0 1 0 0.00% 0.00% 0.00% 0 IPC Session Serv 18 1620 2980310 0 0.00% 0.00% 0.00% 0 IPC Deferred Por 29 0 1 0 0.00% 0.00% 0.00% 0 Exception contro sh run(greped): http://pastie.org/5483194 Hardware: c7200p-adventerprisek9-mz.151-4.M1.bin Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 2xxxxxxx MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2 6 slot VXR midplane, Version 2.1

  Read the article

• Windows XP VM on VMWare ESXi 4.1 "pausing" / blocked occasionally

  - by FelixD

  We have an issue with Windows XP SP3 VMs on VMWare ESXi 4.1.0 (the free version): They sometimes seem to "pause" for several minutes. This happens rarely (maybe once a month per VM, at least noticed only that often), but still is an issue for us. It happens for three different but similar VMs on three pretty different hosts (different hardware). I have the feeling that the "pausing" is not actually the CPU blocking, but probably the harddisks, but not 100% sure. The servers have one IDE disk (C:) and one SCSI (D:) and it might be either of the two. I have seen scheduled tasks simply not starting for up to 9 minutes and then running normally again with normal speed. They were totally blocked. This is not a load issue, the VMWare hosts have average load and the VMs in question already have reserved CPU resources plus high priorities for CPU and disk. The Windows boxes run mainly MySQL, Tomcat, FileZilla server, Cygwin stuff, Java + R applications, VMWare client, Elusiva Terminal Server pro, Nagios client. Not sure if this might be related with any of that software (e.g. Elusiva). Trying to debug this, there was nothing visible in Windows Event log, other logs in C:\Windows, VMWare events etc. Unfortunately the vmware.log file ends with "Log throttled". We found that we ran into 2 VMWare bugs there: The VMWare client writes lots on bogus messages in the vmware.log, which we now disabled (log level error setting) plus the bug that VMWare does not unthrottle the log (at least so far despite VM reboots). I know there is not much guidance and that may also be the reason why I so far didn't find anything related on the web or on ServerFault, but maybe some of this rings a bell with someone? Or please direct me to what more info to post. I hope that the vmware.logs get unthrottled eventually (can't easily restart the hosts at the moment). Thanks for any input!

  Read the article

• RDP with multiple monitors, display preferences get reset?

  - by Martijn Kooij

  Problem: When I connect to my pc at the office via RDP all the application windows I had previously carefully placed on either monitor 1 or 2 will be "scrambled". Either all applications show on monitor 1 and monitor 2 is empty, or they have switched 1 <- 2. Expected behaviour: When I connect I see all the application windows on exactly the same position and in the exact same size as I left them the night before. I have the exact same monitors at home as I have at work: Primary 2560x1440, Secondary 900x1440. Yesterday I tried switching the physical cables on the host machine hoping that the hardware order of the monitors was the difference. But this morning my secondary monitor was completely blank, not even the taskbar (which I had set to ONLY show on the secondary). Somewhere there must be something to help Windows understand which physical monitor is which virtual RDP monitor is which RDP "server" monitor... Are there more options than switching the cables? This one has been bothering me for a long long time now, I hope someone has a solution or workaround for me. Edit I want to use both monitors, so I have checked the "Use all monitors" setting in the RDP client. For example I leave my mail and total commander on the right monitor, and visual studio and Firefox on the left monitor. When I connect to RDP I want to see those applications on the same positions and sizes.

  Read the article

• Windows 7 host with Ubuntu Guest and a performance hit, memory locks?

  - by Cyrylski

  I have a brand new Lenovo T510 with Core i5 and 4GB of RAM with Windows 7 on it. I Installed Ubuntu 10.10 in a Virtualbox. For some reason system gets really slow on this setup which makes me really angry. There's a video card shared with full 3D support enabled and 1GB of RAM allocated for the Ubuntu machine. It may sound stupid, but WHY is the whole memory consumed in an instant when I run Virtualbox? I struggled for like 10 minutes restraining myself from a brutal reset, and now everything runs smooth but memory "in use" in Resource Monitor is 3GB flat with only Chrome running. I'm new to Windows 7, but I'm really disappointed with performance at this point... I used to work in a different environment with much slower hardware and there was no such problem (WinXP over Ubuntu, 1GB out of 2GB allocated for WinXP guest on intel GMA). This is, until I clogged RAM totally there. But I was capable of running Chrome, Firefox and Apache server on a 1GB RAM in Ubuntu there and Photoshop CS4 on Windows XP and it worked. In this case I can't go beyond setting up Ubuntu properly. I bet I'm doing something wrong.

  Read the article

• Ubuntu loading stops ?

  - by joxnas

  I don't know why, or how... but my ubuntu's loading / booting stops right after the ubuntu logo appearing.. An underscore appears in the right top of the screen: _ then, it disappears leaving the whole screen black Version is 9.10 ,Kernel is .20 I have tryed recovering mode and selected recover damaged packages option, but it didn't do any good.. I have very important files in Ubuntu that I need to copy to a pen drive or something, today.. The terminal mode is working, so i think i can do this there.. My questions: How can I get my Ubuntu to load? Is it possible to copy the files i need via terminal mode? I dont know if with other of the previous kernels it would work... but I had configured my grub (inside Ubuntu's gui) to show only the last kernel... and now i can't select any other kernel then .20 because I don't know a way to configure Grub unless via Ubuntu's gui... My hardware: ATI Mobility Radeon 4650 HD P7450 2.13Ghz Core duo 4Gb DDR2

  Read the article

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• How many guesses per second are possible against an encrypted disk? [closed]

  - by HappyDeveloper

  I understand that guesses per second depends on the hardware and the encryption algorithm, so I don't expect an absolute number as answer. For example, with an average machine you can make a lot (thousands?) of guesses per second for a hash created with a single md5 round, because md5 is fast, making brute force and dictionary attacks a real danger for most passwords. But if instead you use bcrypt with enough rounds, you can slow the attack down to 1 guess per second, for example. 1) So how does disk encryption usually work? This is how I imagine it, tell me if it is close to reality: When I enter the passphrase, it is hashed with a slow algorithm to generate a key (always the same?). Because this is slow, brute force is not a good approach to break it. Then, with the generated key, the disk is unencrypted on the fly very fast, so there is not a significant performance lose. 2) How can I test this with my own machine? I want to calculate the guesses per second my machine can make. 3) How many guesses per second are possible against an encrypted disk with the fastest PC ever so far?

  Read the article

• My Hard Drive isn't Working

  - by MeCB

  I never use Safely Remove Hardware with Windows XP. It has been working for me for years with my SD card, mouse, hard drive and memory stick. My hard drive has a USB cable and power cord so I can hook it up to any desktop hard drive. Now my hard drives don't like this and I did not know this till now. I am always careful and to wait till it is all finish accessing the USB before I unplug it. Now three of my hard drives can't be seen by Windows, though the others still work. when I hook it up to another computer it works fine. I use the same USB cable to hook up all of my hard drives one at a time. So my USB cable is good. I think that when I unplugged the hard drive this one time, it had a file it still wanted to see and now only this drive does not work only this computer. Then the same thing happens to my other two hard drive after I used it for a week with the same cables. How can I fix this?

  Read the article

• .bat file - Nagios v3.2 service check and start if stopped

  - by LbakerIT

  I'm just barely getting into programming so I do apologize for my ignorance. I'm trying to create a .bat file that will check if a service is running on XP Pro. If service is running it will exit 0. If the service is stopped start service wait 10 seconds (via ping i'm guessing) check if service is running if service is running exit 0 if service is stopped start service wait 10 seconds Do this check a total of 3 times. if service does not come up within that time: exit 2 Exit 0 = ok exit 1 = warning exit 3 = critical (and this will alert) I need to do this for 3 different services but i'm expecting that it would be better to create one per service. That way you get notified on the specific service that is not coming back up. The goal is that if the service stops it will start it. If after 30 seconds it is unable to start the service then it will send an alert. The reason I'm trying to do it with a .bat is this is consistent with all other scripts and I did not want to complicate it further by adding different kinds of code. Yay for consistency! Again I do apologize for my ignorance I've been thrown into this project last minute. Thank you for the help and reading my question!

  Read the article

• 2.6.9 Kernel on virtual server (non upgradable) - any expected problems?

  - by chris_l

  Hi, I'm considering to rent a virtual server (for me personally). The product I'm currently looking at offers IMO fair pricing, very good hardware etc. The only problem is, that I won't be able to do an upgrade to a newer kernel than 2.6.9 (running Debian Etch). Also, I can't install my own kernel modules. (The server runs with Virtuozzo, so as far as I understand it, it just does some chroot instead of a real virtualization (?)) I want to run GlassFish, Postgres, Subversion, Trac and maybe some other things on it. It will also have to employ a firewall, and provide OpenSSL for https. Ideally, it would also be able to do AIO (asynchronous IO), which could speed up some server I/O. Should I expect problems with that old kernel version, in conjunction with the software I want to install (I'd like to use current versions of the software)? One thing I already found out, is that you can't do everything with iptables, since some kernel modules are missing/things are not build into the kernel. GlassFish v3 appears to run fine at first glance. I was able to test the server for a few hours. Installing my whole setup wasn't feasible in that time, but what I can say is, that it's amazingly fast for an entry-level vserver, especially hard disk and network performance (averaging at ca. 400MBit/s). So if the kernel won't be a problem, I'd really like to take it. Thanks, Chris PS Exact kernel version: 2.6.9-023stab051.3-smp

  Read the article

• apache/httpd responds slower under EL6.1 than EL5.6 (centos)

  - by daniel

  I've read through other threads on performance differences between RHEL6 and RHEL5, but none seem a tight match to mine. My issue manifests itself in slightly slower average response time (20ms) per request. I have about 10/10 servers of the same hardware spec with Cent6.1 and Cent5.6. The issue is consistent across the group. I am running Ruby on Rails with Passenger. Apache config is identical (checked out from the same SVN repo) Ruby and Passenger are identical builds. Application is identical and being served traffic round robin. mod_worker An interesting clue from server-status: The Cent6.1 servers have a steady 20-40 threads in the "Reading Request" state while the Cent5.6 servers have around 1. I'm graphing this so I can see it trend over time. I also have a bunch of much newer machines that are significantly faster and are running Cent6.1. They dust all the older machines in response time, but I can see they also have a steady 20-40 threads in the "Reading Request" state. This makes me believe I can get their response time down, if I can figure out what is holding up these requests. My gut is telling me that I need to tune some network setting in sysctl, but I haven't figured it out yet. Help is appreciated.

  Read the article

• Variable host IP address in iptables rule

  - by DrakeES

  I am running CentOS 6.4 with OpenVZ on my laptop. In order to provide Internet access for the VEs I have to apply the following rule on the laptop: iptables -t nat -A POSTROUTING -j SNAT --to-source <LAPTOP_IP> It works fine. However, I have to work in different places - office, home, partner's office etc. The IP of my laptop is different in those places, so have to alter the rule above each time I change place. I have created a workaround which basically determines the IP and applies the rule: #!/bin/bash IP=$(ifconfig | awk -F':' '/inet addr/&&!/127.0.0.1/{split($2,_," ");print _[1]}') iptables -t nat -A POSTROUTING -j SNAT --to-source $IP The workaround above works. I only still have to execute it manually. Perhaps I could make it a hook executing whenever my laptop obtains an IP address from DHCP - how can I do that? Also, I am just wondering if there is an elegant way of getting it done in the first place - iptables? Maybe there is a syntax allowing to specify "current hardware ip addres" in the rule?

  Read the article

• How can I get (g)Vim to display the character count of the current file?

  - by OwenP

  I like to write tutorials and articles for a programming forum I frequent. This forum has a character limit per post. I've used Notepad++ in the past to write posts and it keeps a live character count in the status bar. I'm starting to use gVim more and I really don't want to go back to Notepad++ at this point, but it is very useful to have this character count. If I go over the count, I usually end up pasting the post into Notepad++ so I can see when I've trimmed enough to get by the limit. I've seen suggestions that :set ruler would help, but this only gives the character count via the current column index on the current line. This would be great if I didn't use paragraph breaks, but I'm sure you'd agree that reading several thousand characters in one paragraph is not comfortable. I read the help and thought that rulerformat would work, but after looking over the statusline format it uses I didn't see anything that gives a character count for the current buffer. I've seen that there are plugins that add this, but I'm still dipping my toes into gVim and I'm not sure I want to load random plugins before I understand what they do. I'd prefer to use something built in to vim, but if it doesn't exist it doesn't exist. What should I do to accomplish my goal? If it involves a plugin, do you use it and how well does it work?

  Read the article

• Trying to diagnose network problem: ping 127.0.0.1 (or any address) results in error code 1

  - by Mnebuerquo

  NIC seems to be working, as windows detects the hardware and has a driver and reports success. DHCP seems to have gotten an ip address, 192.168.1.101. I released and renewed it and it seemed to work normally. I tried ping 127.0.0.1 as first step of testing network configuration. Pinging 127.0.0.1 with 32 bytes of data: PING: transmit failed, error code 1. I read somewhere that net helpmsg [error code] would give a human readable name for the error code. net helpmsg 1 says "Incorrect function" I've tried disabling the firewall and antivirus in McAfee SecurityCenter and I still get the same error. Could the firewall/antivirus be breaking it even if disabled? Broadcom Advanced Control Suite 2 is installed, and its network test passes all tests, including ping 192.168.1.1 which is the default gateway. If I try ping 192.168.1.1 from the command prompt I get the error code 1 again. So does anyone have any theories that would explain this problem? Other tests I should try? Thanks!

  Read the article

• Is a modem required to be programmed when using with an internet provider?

  - by Tim

  I wonder if a modem is required to be programmed when using with an internet provider? If yes, what is the purpose of programming a modem? Do both a DSL and a cable ISP both require a modem to be used in an individual home? For example, I have a Motorola modem SURFboard Model:SB5101, Customer S/N: xxx S/N? xxx HFC MAC ID: xxx USB CPE MAC ID: xxx a coil of cable and a splitter from Comcast High-Speed internet Self-Installation Kit, which were bought 5 years ago, when I purchased Comcast internet service from its retailer www.comcastoffers.com. With them, I was hoping to reduce the amount of fee by avoiding to ask Comcast people to come over to install. But I remember at that time Comcast sent its technician here, dismissed my idea of self-installation, saying they needed to use their own modem and charging me a hefty fee, and so my equipments have never been used. I haven't been using Comcast for a long time. I wonder if my modem, cable and splitter (brand new, never used) are still good to use with an internet provider such as Comcast? If needed, we can ignore their policy and just consider the technology side? Or they are not good to use and I must throw them away like trash? Thanks and regards!

  Read the article

• Working with an external button box

  - by Scott

  I tried this question on Stack Overflow, but I was pointed here, so here goes: For a new project for myself, I am looking for a way to be able to (for example) open a pop-up window on my laptop, by pressing a button on an external device (to be build by myself, or at least bought) connected with USB. Basically I would be looking at something like a Arduino or Raspberry (IF I am looking in the right direction) with buttons on it, and as soon as I hit a button on the external box with physical buttons, a command activates on my laptop and for example opens a popup window in which I can input tekst. Does anyone know: 1) if it is possible to do this at all. 2) What equipment is needed for the external box, what programming is needed. I preffer .net (dot net) but maybe it can only be done with software from the external box. If anyone can point me in the right direction, like make/model of the external box or websites I would be very happy. I have knowledge of Visual Studio/.net but I am willing to learn other languages if .net is not an option for this project. Thanks in advance Scott PS: If anyone knows of some better tags, or at least knows what I mean and needs me to edit the question, please do tell me... I am new on Stack Overflow/Superuser.

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here?

  Read the article

• IIS 7: launch unique site instance per host name

  - by OlduwanSteve

  Is it possible to configure IIS 7 so that a single site with multiple bindings (or wildcard bindings) will launch a unique instance for each unique host name? To explain why this is desirable, we have an application that retrieves its configuration from a remote system. The behaviour of the application is governed by this configuration and not by the 'web.config'. The application uses its host name as a key to retrieve the configuration. Currently it is a manual process to create an identical IIS site for each instance of the application, differing only by the bindings. My thought, if it were possible, is that it would be nice to have one IIS site that effectively works as a template for an arbitrary number of dynamic sites. Whenever it is accessed by a unique host name a new instance of the site would be launched, and all further requests to that host name would go to that instance just as though I had created the site by hand. I use IIS regularly, but only for fairly straightforward site hosting. I'd like to know if this could be configured with vanilla IIS 7, but would also welcome answers that require a plugin or 3rd party product. Programming/architectural suggestions about changes to the app wouldn't really be appropriate for serverfault.

  Read the article

< Previous Page | 686 687 688 689 690 691 692 693 694 695 696 697  | Next Page >