Search Results

Search found 21463 results on 859 pages for 'broken link'.

Page 698/859 | < Previous Page | 694 695 696 697 698 699 700 701 702 703 704 705  | Next Page >

• Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

  - by Damainman

  I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

  Read the article

• Incorrect deployment of WSGI app to AWS using Elastic Beanstalk

  - by Dzmitry Zhaleznichenka

  cross-link to AWS forums I have developed a simple Python web service using WSGI and would like to deploy it to AWS cloud using Elastic Beanstalk. My problem is I cannot make all the options I specify in Elastic Beanstalk configuration to be correctly configured in the cloud. For deployment, I use Elastic Beanstalk CLI utility. I have run eb init command and set up the required parameters. After this, a directory named .elasticbeanstalk was created in my source tree. It has two config files that are used for deployment, namely config and optionsettings. The latter one among the other options contains the WSGI configuration that has to update /etc/httpd/conf.d/wsgi.conf at the instances. After some of my adjustments the file has the following settings: [aws:elasticbeanstalk:application:environment] DJANGO_SETTINGS_MODULE = PARAM1 = PARAM2 = PARAM4 = PARAM3 = PARAM5 = [aws:elasticbeanstalk:container:python] WSGIPath = handler.py NumProcesses = 2 StaticFiles = /static= NumThreads = 10 [aws:elasticbeanstalk:container:python:staticfiles] /static = static/ [aws:elasticbeanstalk:hostmanager] LogPublicationControl = false [aws:autoscaling:launchconfiguration] InstanceType = t1.micro EC2KeyName = zmicier-aws [aws:elasticbeanstalk:application] Application Healthcheck URL = [aws:autoscaling:asg] MaxSize = 10 MinSize = 1 Custom Availability Zones = [aws:elasticbeanstalk:monitoring] Automatically Terminate Unhealthy Instances = true [aws:elasticbeanstalk:sns:topics] Notification Endpoint = Notification Protocol = email It turns out that not all of these options are considered when I start the environment or update it. Thus, when I update NumThreads or NumProcesses, the respective parameters get changed in wsgi.conf as expected. But whatever I write to the WSGIPath and StaticFiles parameters, I'm not able to automatically change the respective values of wsgi.conf, they remain Alias /static /opt/python/current/app/ WSGIScriptAlias / /opt/python/current/app/application.py which drives me nuts. Moreover, when I deploy my application using git aws.push and having the following contents of .ebextensions/python.config file, neither of options I specify in it affects the deployment. option_settings: - namespace: aws:elasticbeanstalk:container:python option_name: WSGIPath value: mysite/wsgi.py - namespace: aws:elasticbeanstalk:container:python option_name: NumProcesses value: 5 - namespace: aws:elasticbeanstalk:container:python option_name: NumThreads value: 25 - namespace: aws:elasticbeanstalk:container:python:staticfiles option_name: /static/ value: app/static/ I wonder what I should do to force AWS use all the parameters I specify in the configuration, namely the WSGI Path and path to my static data.

  Read the article

• Symlinks are inaccessible by their full path on OS X

  - by Computer Guru

  Hi, I have symlinks pointing to applications placed in /usr/local/bin which is in the path. However, I can't run these applications from other folders. Even more weird, I can't access them by the full path to the symlink. [mqudsi@iqudsi:Desktop/EasyBCD]$ echo $path (03-26 13:42) /opt/local/bin /opt/local/sbin /usr/local/bin /usr/local/sbin/ /usr/local/CrossPack-AVR/bin /usr/bin /bin /usr/sbin /sbin /usr/local/bin /usr/X11/bin [mqudsi@iqudsi:local/bin]$ ls -l /usr/local/bin (03-26 13:47) total 24280 -rwxr-xr-x 1 mqudsi wheel 18464 May 14 2009 ascii-xfr -rwxr-xr-x 1 mqudsi wheel 12567 Mar 25 04:50 brew -rwxr-xr-x 1 mqudsi wheel 17768 Dec 11 12:41 bsdiff -rwxr-xr-x 1 mqudsi wheel 43024 Mar 28 2009 dumpsexp -rwxr-xr-x 1 mqudsi wheel 280 Sep 10 2009 easy_install -rwxr-xr-x 1 mqudsi wheel 288 Sep 10 2009 easy_install-2.6 -rwxr-xr-x 1 mqudsi wheel 39696 Apr 5 2009 fuse_wait lrwxr-xr-x 1 mqudsi wheel 29 Mar 25 04:53 git -> ../Cellar/git/1.7.0.3/bin/git [mqudsi@iqudsi:local/bin]$ /usr/local/bin/git (03-26 13:47) zsh: no such file or directory: /usr/local/bin/git Clearly the link is there, but I'm not able to get it to it :S

  Read the article

• django : Serving static files through nginx

  - by PlanetUnknown

  I'm using apache+mod_wsgi for django. And all css/js/images are served through nginx. For some odd, reason when others/friends/colleagues try accessing the site, jquery/css is not getting loaded for them, hence the page looks jumbled up. My html files use code like this - <link rel="stylesheet" type="text/css" href="http://x.x.x.x:8000/css/custom.css"/> <script type="text/javascript" src="http://1x.x.x.x:8000/js/custom.js"></script> My nginx configuration in sites-available is like this - server { listen 8000; server_name localhost; access_log /var/log/nginx/aa8000.access.log; error_log /var/log/nginx/aa8000.error.log; location / { index index.html index.htm; } location /static/ { autoindex on; root /opt/aa/webroot/; } } There is a directory /opt/aa/webroot/static/ which have corresponding css & js directories. The odd thing is that the pages show fine when I access them. I have cleared my cache/etc, but the page loads fine for me, from various browsers. Also, I don't see any 404 any error in the nginx log files. Actually the logs for nginx are not getting refreshed at all. I restarted the nginx server using root, is that incorrect ? There is a user www-data defined in the nginx configuration file. Any pointers would be great.

  Read the article

• pgpoolAdmin keeps going straight back to it's login page

  - by user705142

  I'm trying to run pgpoolAdmin through nginx - it seems to be working properly, at least initially. I've gone through the initial set-up, which works fine, but now after logging in every link takes me straight back to the login page. It also shows japanese text instead of english, despite picking english in the installation. It seems to me just as if it was unable to save any user data, session information etc. I have javascript/cookies enabled, so it's not that. The ownership of the folder is nginx, and so too is pgmgt.conf.php, so it shouldn't be a problem with permissions. One potential issue is that I can't seem to see any confirmation that php postgresql support is enabled in the php info screen, despite the correct package installed and in the config line. Any ideas as to what's happening here? The nginx rules are pretty standard: server { # pg-pool admin listen 997; server_name localhost; root /opt/pgpooladmin; index index.php; location ~ .php$ { fastcgi_pass_header Set-Cookie; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; include fastcgi_params; } }

  Read the article

• vsftpd not allowing uploads. 550 response.

  - by Josh

  I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

  Read the article

• HTTP downloads stop after some time, resuming is not possible

  - by cdauth

  When I try to download a file via HTTP, the downloads sometimes stop after around 30 MB. The download rates goes down to 0 B/s and no data keeps coming. When I stop the download and resume again, the download still hangs. But when I redownload it from byte 0 again, everything works fine up to 30 MB when it stops again. Sometimes, after some hours, it just works again without problems. The position in the file when the download stops is variable, but most of the time it is around 30–35 MB. As a download manager I use wget. The same behaviour happens though using curl and other download managers. The error occurs independently of the server I download from. I have also observed this error on other Linux computers in my network. All computers on my network run Gentoo Linux on x86. All internet connections on my network go through a server on my network which runs a transparent Squid proxy on port 80. That server is connected to a router, which is a Speedport W 700V by Deutsche Telekom AG. That router is connected to the internet using ADSL, with 448 kbit/s down speed and 96 kbit/s up speed. I am almost sure that my transparent proxy is not the problem. I turned that off without resolving the issue. I also connected to the router directly via WLAN without resolving the issue. I also tried to download over another port via HTTP. Furthermore, I tried to download the file using IPv6 with a gateway6 tunnel from my computer, which resulted in exactly the same problem. Now the strange thing is that everything works fine using FTP and HTTPS (also with wget on the same computer). Even more strange: when I resume the download that hanged over HTTP using FTP or HTTPS, download a few bytes that way, stop wget and then resume again using HTTP, it loads data again! But after a few MB, it may stop again. Unfortunately, files downloaded that way are always broken (the MD5 sum is not correct), so at some point, there must have been bogus data. I tried searching for HTML error messages in the downloaded file, but grep -i html does not find anything. (I cannot think of a way to search for GZIP-compressed HTML error messages in the file, so I did not try that.) I tried using strace on wget when it failed to resume a download, you can find the entire output on pastebin. The important lines are repeated every second: clock_gettime(CLOCK_MONOTONIC, {326102, 62176435}) = 0 ) = 1 write(2, "78% [++++++++++++++++++++++++++++"..., 19578% [+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ] 110,683,685 --.-K/s ) = 195 select(4, [3], NULL, NULL, {0, 949999}) = 0 (Timeout) I have absolutely no idea what could be the reason of this problem. It seems like whatever causes the issue speaks HTTP. It seems to speak HTTP that intelligently that it even regognises it in an IPv6-over-IPv4 tunnel. But what could that be and why does it only happen sometimes? The other possibility would be that there is a problem on my computer that is the same on other Gentoo Linux computers as well. Has anyone ever had such a problem? What could be the reason and where do I have to continue investigating to find out more about the issue? Update: I have just run into the problem again and tried to resume the download over the router’s WLAN, and this time it worked. Maybe I did something wrong during my last tests with the WLAN. Now maybe my transparent proxy server is in fact the problem. It is a very basic Squid proxy server that does not cache anything. Maybe the fact is interesting that a second Squid proxy runs on the same computer on another port. Update: A download hung again and this time I turned off all firewall settings and stopped all proxy servers. I failed to resume the download from my network server, which is directly connected to the router. So my proxy server definitely is not the cause the problem. I will try to upgrade the firmware of my router now, although I do not have admin access to it. I will see what I can do.

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Integration of SharePoint 2010 with TFS2010

  - by Kabir Rao

  We have performed following steps as of now- Install TFS2010 10.0.30319.1 (RTM) on Windows Server 2008 R2 Enterprise(app tier) SQL 2008 SP1 with Cumulative update 2 on Windows Server 2008 R2 Enterprise(data tier) Reporting Service is installed on app tier. After this installation worked fine we installed SharePoint 2010 on app tier. After installation we followed http://blogs.msdn.com/b/team_foundation/archive/2010/03/06/configuring-sharepoint-server-2010-beta-for-dashboard-compatibility-with-tfs-2010-beta2-rc.aspx for configuration. We are not able to perform the last step described in the link as following error occured- TF249063: The following Web service is not available: http://apptier:31254/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. The underlying error is: The remote server returned an error: (404) Not Found.. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://apptier:31254. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. We have also noticed that Document Folder in Team project also have red x. Please help. Thanks upfront.

  Read the article

• How do I resolve certificate errors on HP blade center

  - by Martin Hilton

  I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

  Read the article

• Why do I often have to refresh pages I navigate to once for them (or content in them) to load?

  - by GetOutOfBox

  I have noticed a bizarre pattern when using my PC, that when I open a link to a website, it often will often take a very long time to load, or time out. Sometimes content on the website will be drawn, but again, it seems to get "stuck" for an unusual amount of time before finishing. Most affected is Youtube; almost every time I navigate to a youtube video from another website such as Google, the video will not begin playing, but will instead just display the player controls with a black screen where the video should be and the buffering symbol, usually before displaying an error such as "The video failed to load". The unusual part of this problem is that whenever this happens, refreshing the page always causes it to load almost immediately the second time around, without any problems. Note that I'm not talking about how some browsers will dump whatever has been cached to the "pallet" briefly when the page is refreshed or loading stopped; but that the second time loading the website being faster. I have done my best to rule out some of the obvious causes: My Windows 7 desktop computer is the only device that seems to be affected. I use Firefox on it (latest version, flash updated, etc). My connection has more than enough bandwidth (30 megabits down, 4 up), and I've even tried QoSing all other devices to make sure this isn't happening due to usage spikes. Wireshark is not showing any clearly unusual network activity (i.e frequently dropped packets).

  Read the article

• ajax.googleapis.com stopping my Firefox

  - by Oscar Reyes

  Today for some strange reason, Firefox stops working properly because it is trying to fetch something from ajax.googleapis.com. Is there something I can do to avoid this? Safari and Chrome work just fine. I tried uninstalling Firebug and clearing the cache. The only thing that worked was disabling the JavaScript altogether. This seems to be the culprit link: http://ajax.googleapis.com/ajax/libs/jquery/1.3.2/jquery.min.js What can I do? EDIT I think I have found where the problem is. My proxy is serving one byte at a time the file, so firefox consume it at that peace. What I don't understand is why Safari and Chrome takes it right away. What I did last night was, leave the FF open all the night to give him change to load the file, my hope was that I got cached and the next time there was no need to go for it. Today in the morning, the page load successfully but the page was not cached, because the next request failed the same. Here's a video showing the problem:

  Read the article

• PFSense VPN Routing

  - by SvrGuy

  We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

  Read the article

• Problems mounting HPUX LVM+VXFS filesystem on Linux

  - by golimar

  I have a physical disk from a HPUX system that I need to access from a Debian Linux for ia64 system. From the hpux-lvm-tools project I have the tools to access the HPUX LVMs (Linux LVM has a different format) and I also have the freevxfs driver. I know beforehand that the disk has three partitions, and that the biggest one contains LVM volumes, and some of those are VxFS filesystems. I can see the partitions: # cat /proc/partitions major minor #blocks name 8 32 143374744 sdc 8 33 512000 sdc1 8 34 142452736 sdc2 8 35 409600 sdc3 It finds a VG in one of the disk partitions: # ./vgscan_hpux On /dev/sdc2 - vg1328874723 # ./pvdisplay_hpux /dev/sdc2 PV General Information ---------------------- VG Creation Time Fri Feb 10 12:52:03 2012 Physical Volume ID 1766760336 1328874723 Volume Group ID 1766760336 1328874723 Physical Volumes in VG 1766760336 1328874723 VG Actication Mode 0 - LOCAL PE Size 64 MBs Lvol sizes ---------- lvol1 - 8 Extents - 512 MBs lvol2 - 192 Extents - 12288 MBs lvol3 - 16 Extents - 1024 MBs ... lvol21 - 13 Extents - 832 MBs lvol22 - 224 Extents - 14336 MBs lvol23 - 16 Extents - 1024 MBs Then I activate that VG and some new devices appear in my system: # ./pvactivate_hpux /dev/sdc2 VG vg1328874723 Activated succesfully with 23 lvols. # # ll /dev/mapper/ total 0 crw------- 1 root root 10, 59 Nov 26 16:08 control lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol1 -> ../dm-0 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol10 -> ../dm-9 ... lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol8 -> ../dm-7 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol9 -> ../dm-8 But: # mount /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: you must specify the filesystem type # mount -t vxfs /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: wrong fs type, bad option, bad superblock on /dev/mapper/vg1328874723-lvol18, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # lsmod |grep vxfs freevxfs 23905 0 I also tried to identify the raw data with the file command and it just says 'data': # file -s /dev/mapper/vg1328874723-lvol18 /dev/mapper/vg1328874723-lvol18: symbolic link to `../dm-17' # file -s /dev/dm-17 /dev/dm-17: data # Any clues?

  Read the article

• Need Info on the Hidden Switch in SET - "/S" How to implement

  - by ttyl

  I am having some problems doing a proper search of "SET/S" or "SET /S" on google and other search providers. The difficulty arises with the SLASH "/", it is commonly used in search engines to add a "nearness" to the search parameter. I have found no way to escape the SLASH when searching for a SLASH. For those on this community, try searching this domain with the two search terms listed above. It just doesn't work, it ends up looking for SET S instead. But I digress. So Im asking the uber-guru's on this board to help me find out about the documentation of /S and how to implement SET /S in a batch file. SET is an internal DOS/cmd commandand allows many things incuding prompting the user, integer math and writing environment strings. in looking at this link: http://www.robvanderwoude.com/os2set.php it appears that the /S is only for OS2 but im thinking that this might not be the case, due to this: http://www.dostips.com/forum/viewtopic.php?t=2704, apparently used with substings and macros. any help is much appreciated

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Optimal Networking Setup for a 2-Story unit?

  - by user29336

  I am moving into a 4 bedroom two-story unit. It’s roughly 2,200 sq ft. I want absolute max throughput possible to be achieved in all focal points. We’re all in internet related industries. Between gaming and web-development latency and throughput are major factors for us. Here’s our main focal points: 1) Garage (office). downstairs 2) Each bedroom x4. upstairs 3) Living room. downstairs The fastest line we can get is Comcast 50mbdown/5up (Wideband). I am looking for the best way to achieve wireless and wired performance for our setup. Our gaming computers may be in our bedroom, and we also may bring it down to the office every now and then for “LAN” sessions. Most wireless will be happening downstairs with our laptops, but since we may do LAN sessions then hard wired latency may be important there too. My concerns: If we do only wireless there would be too much latency for gaming. I don’t know if placing one D-link DGL 4500 on the top floor would be enough; which I currently own. (http://dlink.com/us/en/home-solutions/support/product/dgl-4500-xtreme-n-gaming-router) As far as I’m aware wireless signals transfer best top down. Would this wireless router be enough on top floor and that’s it? My second strategy was a combination of wiring and wireless but I’m not sure what’s easiest way to do this? This is a place we’re renting, so I’m not sure how much leeway we have with wiring, but we’re all pretty competent... if we can’t drill through a wall we can probably “stitch” them across the edges wherever needed. Thoughts on the optimal way to do this?

  Read the article

• How do I create a wifi network bridge with qemu on OS X?

  - by a paid nerd

  I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

  Read the article

• Advanced Linux file permission question (ownership change during write operation)

  - by Kent

  By default the umask is 0022: usera@cmp$ touch somefile; ls -l total 0 -rw-r--r-- 1 usera usera 0 2009-09-22 22:30 somefile The directory /home/shared/ is meant for shared files and should be owned by root and the shared group. Files created here by usern (any user) are automatically owned by the shared group. There is a cron-job taking care of changing owning user and owning group (of any moved files) once per day: usera@cmp$ cat /etc/cron.daily/sharedscript #!/bin/bash chown -R root:shared /home/shared/ chmod -R 770 /home/shared/ I was writing a really large file to the shared directory. It had me (usera) as owning user and the shared group as group owner. During the write operation the cron job was run, and I still had no problem completing the write process. You see. I thought this would happen: I am writing the file. The file permissions and ownership data for the file looks like this: -rw-r--r-- usera shared The cron job kicks in! The chown line is processed and now the file is owned by the root user and the shared group. As the owning group only has read access to the file I get a file write error! Boom! End of story. Why did the operation succeed? A link to some kind of reference documentation to back up the reason would be very welcome (as I could use it to study more details).

  Read the article

• network latency, TCP and UDP packets

  - by user115848

  Hello recently my network has started to cause me lots of problems. I have a cable modem, connected to a tp-link router (with some port forwarding). Everything was working fine then i started to get lots of udp (port 53) "UNREPLIED" logs in the router. Now there are tcp UNREPLIED logs too. This is causing lots of latency and failed connections when trying to connect to different internet sites. Also, we run an openfire server for spark connections, and I believe its causing connectivity issues for some users who are trying to connect using Spark (some people connect fine, others don't). Please see screen shot below for packet logs. It has to be something internally, as I connected straight to the comcast modem and i was able to connect to the internet and various sites as normal. I tried to swap out the router with a different and got the same issue. I scanned both my internal dns servers for viruses or malware and it came up empty. Another anomaly is that when i try to connect to www.cnn.com, i get redirected to the different site. I scanned my own machine for hijacks. Not sure if this is related to the networking issue. Please let me know if you have any ideas for troubleshooting.

  Read the article

• VMWare Workstation Linux Host performance tuning

  - by Hoghweed

  I need to improve my linux hosted vmware workstation for using multiple virtual machines at the same time. I feel very stupid I lost a great blog post link which I found last month (and I'm not able to find it again..) so I try to ask here if anyone can help me: This is my host (laptop): 16GB DDR3 Ram HDD Hybrid 750GB 7200 (8GB SSD Cache) Mint 15 x64 Kernel 3.9.7 swappiness set to 10 The above are the important things about the host. So, My need is the ability to run 2 or 3 VMs at the same time. The lack of performance is about the disk, The last time from that blog post I lost, I setup /tmp to be mounted ad a memory partition and in my previous installation that was good, now I'm not able to find a good solution to tweak the things. I think with 16GB o RAM there will be no problems to run multiple VMs, but whe they start to swap or use the /tmp things going bad (guest cursor going too fast after a freeze, guest freeze and so on) Anyone can help me to fit a good host tweak and configuration to get better performance? Thanks in advance

  Read the article

• Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

  - by user3014097

  I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

  Read the article

• administrator user unable to login, suspicious user accounts "sky$", "admin$"

  - by mks

  I have a Windows 2008 R2 Standard (64 bit) running in a virtual machine. Suddenly from yesterday onwards I am not able to login as administrator. Nobody changed the password. Both in the console as well as using remote desktop I am unable to login. Whenever I login as Administrator I am getting this error: "The user name or password is incorrect" Nothing has changed in the machine and I have logged in the past successfully both through console and via remote desktop several time on the same machine. One strange behaviour I noticed is, I am seeing some additional user accounts if I try to login as other user. The suspicious user account are: sky$ admin$ SUPPORT_388945a0 Is it created by some malware/virus? Or is it some windows hidden account? Microsoft site says that SUPPORT_388945a0 is: The Support_388945a0 account enables Help and Support Service interoperability with signed scripts. This account is primarily used to control access to signed scripts that are accessible from within Help and Support Services. Administrators can use this account to delegate the ability for an ordinary user, who does not have administrative access over a computer, to run signed scripts from links embedded within Help and Support Services. These scripts can be programmed to use the Support_388945a0 account credentials instead of the user’s credentials to perform specific administrative operations on the local computer that otherwise would not be supported by the ordinary user’s account. When the delegated user clicks on a link in Help and Support Services, the script executes under the security context of the Support_388945a0 account. This account has limited access to the computer and is disabled by default. However I am not sure from where this "admin$" and "sky$" came. Anyone has similar experience?

  Read the article

• How to install smtp/email server to work with php script?

  - by jiexi

  I have this code $mail->IsSMTP(); $mail->SMTPAuth = true; $mail->SMTPSecure = "ssl"; $mail->Host = "mail.craze.cc"; $mail->Port = 465; $mail->Username = "username"; $mail->Password = "pass"; $mail->SetFrom("[email protected]", "craze.cc"); $mail->AddReplyTo("[email protected]", "craze.cc"); $mail->AddAddress($this->email, $this->username); $mail->IsHTML(false); $mail->Subject = "Activate Your Craze.cc Account"; $mail->Body = $message;`enter code here` How i configure my postfix/sendmail or whatever server to actually work and send the mail? This has been driving me insane! I've tried numerous times to configure these servers. I just want to be able to send emails via my php script... Can someone please link me to a guide to get this all going? or just provide help themselves? Maybe there is an alternative way i can use to send my email in the php script? Basically, i need help just getting the emails to send...

  Read the article

< Previous Page | 694 695 696 697 698 699 700 701 702 703 704 705  | Next Page >