Search Results

Search found 20336 results on 814 pages for 'connection strings'.

Page 699/814 | < Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• Password-less login into localhost

  - by Brad

  I am trying to setup password-less login into my localhost because it's required for a tutorial. I went through the normal steps of generating an rsa key and appending the public key to authorized_keys but I am still prompted for a password. I've also enabled RSAAuthentication and PubKeyAuthentication in /etc/ssh_config. Following other suggestions I've seen, I tried: chmod go-w ~/ chmod 700 ~/.ssh chmod 600 ~/.ssh/authorized_keys But the problem persists. Here is the output from ssh -v localhost: (tutorial)bnels21-2:tutorial bnels21$ ssh -v localhost OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /Users/bnels21/.ssh/id_rsa type 1 debug1: identity file /Users/bnels21/.ssh/id_rsa-cert type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 1c:31:0e:56:93:45:dc:f0:77:6c:bd:90:27:3b:c6:43 debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /Users/bnels21/.ssh/known_hosts:11 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/bnels21/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering RSA public key: id_rsa3 debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /Users/bnels21/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Any suggestions? I'm running OSX 10.8.

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Setting environment variables in OS X

  - by Percival Ulysses

  Despite the warning that questions that can be answered are preferred, this question is more a request for comments. I apologize for this, but I feel that it is valuable nonetheless. The problem to set up environment variables such that they are available for GUI applications has been around since the dawn of Mac OS X. The solution with ~/.MacOSX/environment.plist never satisfied me because it was not reliable, and bash style globbing wasn't available. Another solution is the use of Login Hooks with a suitable shell script, but these are deprecated. The Apple approved way for such functionality as provided by login hooks is the use of Launch Agents. I provided a launch agent that is located in /Library/LaunchAgents/: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>user.conf.launchd</string> <key>Program</key> <string>/Users/Shared/conflaunchd.sh</string> <key>ProgramArguments</key> <array> <string>~/.conf.launchd</string> </array> <key>EnableGlobbing</key> <true/> <key>RunAtLoad</key> <true/> <key>LimitLoadToSessionType</key> <array> <string>Aqua</string> <string>StandardIO</string> </array> </dict> </plist> The real work is done in the shell script /Users/Shared/conflaunchd.sh, which reads ~/.conf.launchd and feeds it to launchctl: #! /bin/bash #filename="$1" filename="$HOME/.conf.launchd" if [ ! -r "$filename" ]; then exit fi eval $(/usr/libexec/path_helper -s) while read line; do # skip lines that only contain whitespace or a comment if [ ! -n "$line" -o `expr "$line" : '#'` -gt 0 ]; then continue; fi eval launchctl $line done <"$filename" exit 0 Notice the call of path_helper to get PATH set up right. Finally, ~/.conf.launchd looks like that setenv PATH ~/Applications:"${PATH}" setenv TEXINPUTS .:~/Documents/texmf//: setenv BIBINPUTS .:~/Documents/texmf/bibtex//: setenv BSTINPUTS .:~/Documents/texmf/bibtex//: # Locale setenv LANG en_US.UTF-8 These are launchctl commands, see its manpage for further information. Works fine for me (I should mention that I'm still a Snow Leopard guy), GUI applications such as texstudio can see my local texmf tree. Things that can be improved: The shell script has a #filename="$1" in it. This is not accidental, as the file name should be feeded to the script by the launch agent as an argument, but that doesn't work. It is possible to put the script in the launch agent itsself. I am not sure how secure this solution is, as it uses eval with user provided strings. It should be mentioned that Apple intended a somewhat similar approach by putting stuff in ~/launchd.conf, but it is currently unsupported as to this date and OS (see the manpage of launchd.conf). I guess that things like globbing would not work as they do in this proposal. Finally, I would mention the sources I used as information on Launch Agents, but StackExchange doesn't let me [1], [2], [3]. Again, I am sorry that this is not a real question, I still hope it is useful.

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Postgres pgpass windows - not working

  - by Scott

  DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• Hide/Replace Nginx Location Header?

  - by Steven Ou

  I am trying to pass a PCI compliance test, and I'm getting a single "high risk vulnerability". The problem is described as: Information on the machine which a web server is located is sometimes included in the header of a web page. Under certain circumstances that information may include local information from behind a firewall or proxy server such as the local IP address. It looks like Nginx is responding with: Service: https Received: HTTP/1.1 302 Found Cache-Control: no-cache Content-Type: text/html; charset=utf-8 Location: http://ip-10-194-73-254/ Server: nginx/1.0.4 + Phusion Passenger 3.0.7 (mod_rails/mod_rack) Status: 302 X-Powered-By: Phusion Passenger (mod_rails/mod_rack) 3.0.7 X-Runtime: 0 Content-Length: 90 Connection: Close <html><body>You are being <a href="http://ip-10-194-73-254/">redirect ed</a>.</body></html> I'm no expert, so please correct me if I'm wrong: but from what I gathered, I think the problem is that the Location header is returning http://ip-10-194-73-254/, which is a private address, when it should be returning our domain name (which is ravn.com). So, I'm guessing I need to either hide or replace the Location header somehow? I'm a programmer and not a server admin so I have no idea what to do... Any help would be greatly appreciated! Also, might I add that we're running more than 1 server, so the configuration would need to be transferable to any server with any private address.

  Read the article

• openVPN as a way to connect to a LAN by another client, different from server

  - by Einar

  Setup: one LAN handled by a router without a publicly available IP address but without any outbound connection restrictions ("target LAN"); a separate server publicly reachable from the Internet ("gateway"). I am trying to set up openVPN so that a third client can connect to the "gateway" and access the "target LAN". As the router of "target LAN" is not reachable from the Internet directly, it connects to the gateway itself via openVPN as well. The problem is how to handle routing. The LAN router has two network interfaces (for the outside network and the LAN itself). In openVPN (the server on the gateway) I set client-to-client and push "route 192.168.10.0 255.255.255.0" but I assume this would be horribly wrong (it actually messed up the routing on the LAN router until I killed openVPN). openVPN is not using bridging, is configured via tun. Other config details from the server server 10.8.0.0 255.255.255.0 client-config-dir ccd route 192.168.10.0 255.255.255.0 And the client file in ccd is iroute 192.168.10.0 255.255.255.0 What can be adjusted to ensure that a third client can connect through openVPN and access the LAN mentioned earlier?

  Read the article

• Having two IP Routes/Gateways of last Resort on an HP Switch

  - by SteadH

  We have an HP Layer 3 Switch that is doing IP routing between vlans. The general set up is that the switch has an IP address on each VLAN and IP routing is enabled. On our servers VLAN, we have a firewall that has a connection to the outside world. To set a IP route on the HP router, we use IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.1 where 192.168.2.1 is the address of our firewall, and the zeros essentially mean to route all traffic that the switch doesn't know what to do with out the firewall as a gateway. We're in the middle of an ISP and firewall change. I set up the new firewall and ran the IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.254 (the address of the new firewall). Things started working nicely. When I reviewed the configuration of the switch though, I noticed that it did not replace the previous ip route command, but just added another route. Now, I know how to remove the old firewall route (no ip route 0.0.0.0 0.0.0.0 192.168.2.1), but what is the effect of having these two 0.0.0.0 routes? Is it switch implosion? Will a server just respond back over the route it receives the request from? I've read elsewhere that having two default gateways is an impossibility by definition, but I'm curious about this situation that our switch allowed. Thanks!

  Read the article

• How can I monitor VNC via Nagios?

  - by atroon

  I have a number of remote sites which have VNC running on a few computers for support purposes. They are (obviously) only available on our internal network. I am using Nagios to keep track of all the systems in the network and I want to have it check to make sure the VNC server is running on the appropriate hosts. There is a 'check_vnc' plugin available here but it relies on VNC Snapshot which I don't want to use. Certainly I could use it, but it adds more complexity and dependency, which I want to avoid. It seems simpler to just use check_tcp to make sure I get the proper response to a connection request for VNC, e.g. port 5900, send a connect string, get back framebuffer info. My real question, I suppose, is this: What is the 'proper' generic connect string for VNC (I use both UltraVNC and RealVNC) and what is the expected response? If it's really easier to use the VNC Snapshot and check_vnc, let me know. I just can't imagine that a string of text isn't easier, faster, and less bandwidth intensive to monitor.

  Read the article

• Limiting bandwith on an Windows 7 machine

  - by Mihai Damian

  I need to limit the bandwidth on my Windows 7 x64 machine. In the past (on XP) I've been able to use NetLimiter for similar tasks. However for some reason I can't get it to work anymore. For lower limits the bandwidth tests are able to exceed the limit by 10-50%; higher limits seem to be ignored completely and the bandwidth tests report download speeds of over 10 times the speed I set. I'm using speedtest.net and some similar service from my ISP for these tests. Anyway, I don't necessarily need a program as complex as NetLimiter since I only need to throttle my machine's bandwidth, not a specific program's. In case you are wondering why in the world I'd want to cripple my Internet speed, there is a funny story behind this. Long story short, my modem gets random disconnects. Tech support comes in, says my Internet speed is abnormally high and I must be using some tools to somehow make it go faster than it's supposed to and this messes up my modem. I check the connection with another computer and it seems that my PC is the only one in my network that gets abnormal speeds. I reinstall my OS, speed looks normal at first, after I install the batch of 50 or so updates, it goes back to abnormally high speeds and the disconnect problems are not solved. Now I don't have a clue if the explanation the tech team gave me was just a strategy to lay the blame on someone else, but I was trying to give them the benefit of the doubt and see what happens if I really reduce my speed to their specification. Any help appreciated.

  Read the article

• Plesk FTP not working but SFTP and Shell is working

  - by shamittomar

  I am facing a strange problem. The FTP on my Plesk VPS is not working. Whenever I try to connect, FileZilla FTP client says: Status: Resolving address of xxxxxxxxxxxxx.com Status: Connecting to xxx.xxx.xxx.xxx:21... Status: Connection established, waiting for welcome message... Error: Could not connect to server So, it's not even going to the step of asking username/password. So, it's something else. The SFTP on port 22 is working fine. Also, I can successfully do shell access and run commands. But, I NEED FTP access too on port 21. I have searched everywhere but can not find any setting to enable it. This is the Plesk version info: Parallels Plesk Panel version 9.5.2 Operating system Linux 2.6.26.8-57.fc8 CPU GenuineIntel, Intel(R) Pentium(R) 4 CPU 3.00GHz Any help is appreciated. [EDIT]: The firewall is not blocking it. I have checked it on server and there are absolutely no blocking rule. Firewall states: All incoming/outgoing connections are accepted on FTP And on client-side (my PC), I can connect to other FTP servers so this is not an issue in my PC's firewall. Moreover, I can not even connect to the FTP from online FTP clients like net2ftp.

  Read the article

• central apache log analysis of many hosts

  - by Jason Antman

  We have 30+ apache httpd servers, and are looking to perform analysis on the logs both for historical trending and near "real time" monitoring/alerting. I'm mainly interested in things like error rates (4xx/5xx), response time, overall request rate, etc. but it would also be very useful to pull out more compute-intensive statistics like unique client IPs and user agents per unit of time. I'm leaning towards building this as a centralized collector/server/storage, and am also considering the possibility of storing non-apache logs (i.e. general syslog, firewall logs, etc.) in the same system. Obviously a large part of this will probably have to be custom (at least the connection between pieces and the parsing/analysis we do), but I haven't been able to find much information on people who have done stuff like this, at least at shops smaller than Google/Facebook/etc. who can throw their log data into a hundred-node compute cluster and run Map/Reduce on it. The main things I'm looking for are: - All open source - Some way of collecting logs from apache machines that isn't too resource-intensive, and transports them relatively quickly over the network - Some way of storing them (NoSQL? key-value store?) on the backend, for a given amount of time (and then rolling them up into historical averages) - In the middle of this, a way of graphing in near-real-time (probably also with some statistical analysis on it) and hopefully alerting off of those graphs. Any suggestions/pointers/ideas, to either "products"/projects or descriptions of how other people do this would be greatly helpful. Unfortunately, we're not exactly a new-age-y devops shop, lots of old stuff, homogeneous infrastructure, and strained boxes.

  Read the article

• Slow tracepath on local LAN

  - by Simone Falcini

  I am on EXSi and I have 2 instances: Ubuntu and CentOS. These are the network configurations Ubuntu eth0 Link encap:Ethernet HWaddr 00:50:56:00:1f:68 inet addr:212.83.153.71 Bcast:212.83.153.71 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76059 errors:0 dropped:26 overruns:0 frame:0 TX packets:7224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6482760 (6.4 MB) TX bytes:2080684 (2.0 MB) eth1 Link encap:Ethernet HWaddr 00:0c:29:46:5a:f2 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:252 errors:0 dropped:0 overruns:0 frame:0 TX packets:608 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42460 (42.4 KB) TX bytes:82474 (82.4 KB) /etc/iptables.conf *nat :PREROUTING ACCEPT [142:12571] :INPUT ACCEPT [5:1076] :OUTPUT ACCEPT [8:496] :POSTROUTING ACCEPT [8:496] -A POSTROUTING -s 192.168.1.0/24 -o eth0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [2:72] :FORWARD ACCEPT [4:336] :OUTPUT ACCEPT [6:328] -A INPUT -i eth1 -p tcp -j ACCEPT -A INPUT -i eth1 -p udp -j ACCEPT -A INPUT -i eth0 -p tcp --dport ssh -j ACCEPT COMMIT CentOS eth0 Link encap:Ethernet HWaddr 00:0C:29:74:1C:55 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe74:1c55/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:499 errors:0 dropped:0 overruns:0 frame:0 TX packets:475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68326 (66.7 KiB) TX bytes:82641 (80.7 KiB) The main problem is that if i execute this command from the CentOS instance ssh 192.168.1.2 it takes more than 20s to connect. It seems like it's routing the connection to the wrong network. What could it be? Thanks!

  Read the article

• Samba share will not connect (was working yesterday)

  - by David Gard

  I have a CentOS websver with a Samba share set up (\\webserver\websites). I was connected to this share just yesterday without issue, but today my Windows 8 PC will not connect to it. I've also tried making a connection from Windows 7 and Windows XP, all without success. I initially tried restarting my computer, but that did not work. I then tried restarting the Samba service on the webserver (service smb restart), and when that failed I restarted the webserver. All of that was to no avail, and I still cannot connect to the share. The webserver is contactable from my PC (and the others I tried), as the websites it hosts work fine and I'm able to Putty to the server. When connected to the webserver, I can see that Samba is running by using service smb status - service smb status smbd (pid 4685) is running... nmbd (pid 4688) is running... Can anyone please help me to get this share working? Here is my full Samba config (/etc/samba/smb.conf) - [global] workgroup = MYGROUP server string = Samba Server %v log file = /var/log/samba/log.%m max log size = 50 security = user encrypt passwords = yes socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 local master = no [websites] comment = Websites browseable = yes writable = yes path=/var/www/html/ valid users = dgard

  Read the article

• Proper configuration for Windows SMTP Virtual Server to only send email from localhost, and tracking down source of spam emails

  - by ilasno

  We manage a server that is hosted on Amazon EC2, which has web applications that need to be able to send outgoing email. Recently we received a notice from Amazon about possible email abuse on that server, so i've been looking into it. It's Windows Server Datacenter (2003, i guess), and uses SMTP Virtual Server (you know, the one that requires IIS 6 for admin). The settings on the Access tab are as follows: - Authentication: Anonymous - Connection: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) - Relay: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) In the SMTP logs there are many entries like the following: 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 FROM: 0 0 4 0 26364 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 TO: 0 0 4 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26707 SMTP - - - - ([email protected] is sending quite a lot of emails :-/) Can anyone confirm if the SMTP server settings seem correct? I'm also wondering if a web application on the machine could be exposing a contact form or something that would allow this sort of abuse, looking into that (and how to look into that) further.

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

• Passwortgeschützter Traffic-meter

  - by UncleBob

  Hallo erstmal, ich habe hier ein kleines Problem für das ich bis jetzt noch keine Lösung habe. Ich lebe in Bosnien und teile hier die Internetverbindung mit der Vermieterin, und wie es in Bosnien so ist haben wir keine Flatrate, sondern eine 15 Giga traffic limite. Das wäre eigentlich mehr als genug, wenn der Sohn der Vermieterin nicht immer überziehen würde, sodass die Rechnungen immer ziemlich teuer ausfallen. Ich habe ihm bereits ein Messprogramm installiert, aber das schaltet er offensichtlich aus sobald er in die Nähe seiner Limite kommt und behauptet dann die Limite nicht überzogen zu haben. Ich brauche also mindestens ein Messprogramm das Passwortgeschützt ist und/oder im Log Zeiten vermerkt wärend denen es nicht eingeschaltet war. Noch besser wäre ein Programm das ihm den Netzzugriff einfach abklemmt wenn er seinen Anteil überschreitet, also eine Mischung aus Trafic-meter und Parental Guard. Kann mir da jemand weiterhelfen? Gtranslated version Hi first, I have a small problem for which I yet have no solution. I live in Bosnia and share the Internet connection here with the owner, and how it is in Bosnia, we do not have a flat rate, but a 15 Giga traffic limite. That would actually would be more than enough, if the son of the landlady does not always cover so that the bills always turn out quite expensive. I have it already installed a monitoring program, but he apparently turns out as soon as he comes close to its limit and then claims not to have the limit excessive. I therefore need at least a measurement program that is password protected and / or in the log notes During low periods where it has not turned on. Even better would be a program that disconnects him from accessing the network if it simply exceeds its share, ie a mixture of Traffic parameters and Parental Guard. Can someone help me there?

  Read the article

• How to speed up request/response to django using apache or another solution?

  - by jbcurtin

  Hey all, I'm mainly a developer, but every now and again I jump into the sys-admin position. For the most part I've gotten away with deploying php and python apps using apache. I write today because I'm starting to research faster alternatives to apache, yet still have some of the core features I require like put and delete methods and the ability to connect to a socket via apache. ( This I have not tried, but might be a nice whistle if I ever employ comet on my apps. ) As you've probably guessed, I use javascript exclusively for all my websites utilizing deep linking for SEO support. The main areas that I'm looking to increase performance is the connection between the django apps and the web server to the client response. Every day I work my best to keep the smallest memory foot print as possible, however I am getting to the end of my rope when it comes to working with apache. In general, keep in mind that I'm just starting this research so I'm looking more for material to read then solutions at this moment. My main questions: Am I missing something about apache that makes it faster then everything else? What would be a good server environment to deploy just static files one? What are some of the leading open-source and paid alternatives?

  Read the article

• What is the reason for this DNSSEC validation failure of dnsviz.net?

  - by grifferz

  On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

  Read the article

• Computer won't start after installing new video card

  - by Vercas

  So, 1 year and 340 days ago I bought a desktop computer. Since then, it has served me well. But lately, I wanted an upgrade, so I bought a new video card. I documented myself about the compatibility, and it is okay. So I opened the case, cleaned up that... dust elemental living inside of it. Unscrewed the plastic thingie on the outside to unscrew the old video card. Because of the stupid arrangement of the ports, I had to unscrew the motherboard to unplug it. So I unscrewed it, removed the old card, put in the new one, moved the motherboard back, screwed it back in, screwed the video card on the holder... thingie, and screwed the plastic thingie back in. Everything went smoothly, nothing had to be forced in/out. I connected the external power supply, closed the computer case, put the tower back in it's place and all the cables back in. When I pressed the power button, the LED turned... some color I can't distinguish. It stayed that way for a second, and then it went off. I tried a bunch of things, including permuting the external power supply arrangement (1 connection, 2 connections and no connections), with no success. And here are some of the specifications: Motherboard manufacturer: Asrock Processor: AMD Athlon II X2 3.0 GHz RAM: 2 x 2GB (had only 1 initially, bought the second plate a bit later) OLD video card: AMD Radeon HD 5450 NEW video card: Gigabyte nVidia GeForce GTX 650 GPU, 1GB GDDR5 128bit PCI-E, Dual-link DVI-Dx2 / HDMI / D-Sub Power supply: 450W + all the requirements I managed to find on the internet are met (+12V 18A or something) More specific information is stored... On that computer. If required, I may open the case again and read the stickers to find more specific information. I can also provide photos if necessary. Any ideas? Suggestions? Something? :|

  Read the article

< Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >