Search Results

Search found 31994 results on 1280 pages for 'input output'.

Page 699/1280 | < Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >

• hp pavilion g6 1250 with a BCM 4313 doesn't see any wireless networks

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation, ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) There are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• How to use qcow2 disk image in Linux?

  - by sauparna

  I have a large qcow2 formatted disk image, which I use as storage. Often I need to move data to and from this disk image. I mount the disk using the qemu-nbd tool as follows: modprobe nbd max_part=63 qemu-nbd -c /dev/nbd0 /host/disk100G.img mount /dev/nbd0p1 /home/rup/disk But disk access fails every now and then in the midst of some I/O operation with an "Input/output error". At that point I have to manually unmount the disk and re-mount it so that I can run the program again: qemu-nbd -d /dev/nbd0 umount joborkhaki/ What could be the reason for this? Is there a better tool that I can use to maintain a qcow2 disk image?

  Read the article

• debian squeeze: where do the logs for sysv init scripts go? (why won't my init script work)

  - by sbeam

  my actual problem is trying to debug a init script to start Resque. It works fine run as root from the command line, but does nothing on boot. It has some proper insserv headers and I've run updaterc.d to create the symlinks, and checked that they exist. The script is +x. # find /etc/rc*.d -name \*resque\* /etc/rc0.d/K01resque /etc/rc1.d/K01resque /etc/rc2.d/S01resque /etc/rc3.d/S01resque /etc/rc4.d/S01resque /etc/rc5.d/S01resque /etc/rc6.d/K01resque # ls -l /etc/init.d/resque -rwxr-xr-x 1 root root 2093 Oct 24 03:02 /etc/init.d/resque the script can be viewed here if you like. It uses lsb functions to log messages, which essentially echo() to STDOUT I believe. So where does the output go during startup? It's not in /var/log/*log

  Read the article

• Debug Apache mod_status showing 151 requests/sec - 2.7 GB/second

  - by James Hackett

  One of my web servers went crazy this morning and showed "151 requests/sec - 2.7 GB/second - 140.7 MB/request" the normal is like "11.1 requests/sec - 65.6 kB/second - 5.9 kB/request" I don't even think that kind of through put is possible on my server. It was also listing odd symbols for the urls and the amount of data transfered for connections was off the meter 246-0 -1286402072 0/0/0 ? 0.00 -1444841118 0 -5416403825852416.0 0.00 0.00 °Rk³ 247-0 18 0/0/0 ? -13112985.76 2094967848 0 -5428200825946112.0 0.00 0.00 248-2 23437 0/0/2 _ 0.00 0 0 0.0 0.00 -5340330065920.00 74.53.23.134 web2.mydomain.com OPTIONS / HTTP/1.0 249-2 23279 0/2981898840/0 W 16673317.60 11 0 0.0 2844.06 0.00 201.144.221.245 www.mydomain.com GET /cb8ff49a2395a7b1accbbce1e4cf164f/view/256 HTTP/1.1 250-0 0 40600/3009863336/0 ? 3816369.92 910209710 0 2913775.3 -5323551899648.00 -5324315849947.28 èøϲ Has anyone seen anything like this before and know what might be causing it? I posted the full mod_status output here http://pastie.org/916066

  Read the article

• OS X Snow Leopard stops processing clicks from Wacom Intuous2

  - by antiver

  I'm using a Wacom Intuos2 graphics tablet in OS X Snow Leopard 10.6.2, which works great, 80% of the time. Every 20 minutes or so, OS X to just start ignoring input from the pen. More specifically, only the pen tip is ignored - the side buttons on the pen still work. Putting the Mac to sleep and waking it back up restores functionality to the pen tip. This is using both of the latest Wacom drivers claiming compatibility with Snow Leopard: versions 6.1.2-5 (Nov 25, 2009) and 6.1.3-3 (Jan 21, 2010). I have no experience with this tablet with other version of OS X / drivers. The tablet works 100% in Windows, which leads to blame either OS X or the OS X drivers.

  Read the article

• Computer starts, POSTs normal, no video

  - by Annath

  So, I recently tried to start up an old computer of mine. It would not power on, so I replaced the PSU. When I powered it on, all the fans spun up and the POST beeps indicated a normal startup. The problem was there was no video output. Every couple of minutes, I hear the post code again. I think it is restarting after POST, but without video I have no idea why. Does anyone have an idea as to why this is happening, and how to fix it? EDIT: The video card is a PCI-e card. There is no integrated graphics on the motherboard. If I remove the video card, the POST indicates a missing card. When I put it back, it goes back to normal, so I know that it recognizes that the card exists.

  Read the article

• How do I pipe a list of numbers straight from the shell into a command?

  - by learnvst

  How do I pipe a list of numbers straight from the shell into a command? For exampe something like this [1,2,3,4] | sort would give 1 2 3 4 EDIT: In response to the answers kindly posted so far . . . I ask this, because I want to quickly test and debug a console application that takes many numbers as it input without having to type lots of individual values followed by carriage returns. I'd like to just type in the 'one liner' and hit the up arrow now and then to replay the command. Ideally, I'd like to do this without using a text file containing the values (which would obviously be the most simple way to do this.)

  Read the article

• How can I make ls and xargs combined omit path

  - by Steve McLeod

  I have a folder called lib. In that folder are some files. I want to obtain all the names of the files that end in .jar, and concatenate them into a line, separated by spaces. I don't want the path name at all. I've tried this: ls lib/*.jar | xargs and the output is lib/file1.jar lib/file2.jar But what I'm trying to get is file1.jar file2.jar How can I do this? I've also tried find but I get the same problem find lib -name *.jar | xargs

  Read the article

• Memory Stick Controller is not compatible with this version of Windows.

  - by nona urbiz

  I'm getting this error message in the Action Center on Windows 7, and I can't seem to solve it through Windows or through searches on Google: RICOH R5C592 PCI-CardBus/IEEE-1394/SD Card/Memory Stick Controller is not compatible with this version of Windows. Thanks for any help PS. I wasn't sure if you're allowed to post questions like this, about proprietary software, but I checked the FAQ and it seemed ok. Response: The URL I am told to visit it this but I can't tell which I should choose that I am originally presented with, or what to put in to select, as I am not sure what input it is referring to.

  Read the article

• cURL works but PHP cURL fails to internet [migrated]

  - by wrk2bike

  Trying to diagnose an issue using PHP to cURL to an Internet location on a RedHat Linux server. cURL is installed and working, and: <?php var_dump(curl_version()); ?> shows all the correct information in the output. The issue is I can use PHP to cURL to localhost on the box itself, but not the Internet (see below). Normally I'd suspect the firewall, but I can cURL from the command line to the Internet without a problem. The box can also update it's own software packages, etc. What am I missing? My test is: <?php function http_head_curl($url,$timeout=30) { $ch = curl_init(); curl_setopt($ch, CURLOPT_URL, $url); curl_setopt($ch, CURLOPT_TIMEOUT, $timeout); curl_setopt($ch, CURLOPT_HEADER, 1); curl_setopt($ch, CURLOPT_NOBODY, 1); curl_setopt($ch, CURLOPT_FOLLOWLOCATION, 1); curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1); $res = curl_exec($ch); if ($res === false) { throw new RuntimeException("cURL exception: ".curl_errno($ch).": ".curl_error($ch)); } return trim($res); } // Succeeds, displaying headers echo(http_head_curl('localhost')); // Fails: echo(http_head_curl('www.google.com')); ?>

  Read the article

• Sensei mouse sensitivity

  - by Marcelo

  I've recently acquired a Steelseries Sensei. Despite being a great mouse, I'm having some trouble finding settings that I can get used to... The mouse engine allows me to set a CPI from 0 to 5700. It also allows me to set it even higher, calling it "DCPI" (Double CPI), from 5701 to 11400. On Window's Control Panel, there's a "Pointer Speed" slider and a "Enhance Pointer Precision" checkbox (wording may be different as I use a non-english version). The majority of games allow me to set an in-game "Mouse Sensitivity". Some games let me use a "Raw mouse input". I'm already familiar with the basics of CPI/DPI - "higher CPI means less hand movement", but what are the differences between all those options? Is there a "better" or "worst" setting?

  Read the article

• Macos default paths prepend my defined paths in vim

  - by Bogdan Gusiev

  I am trying to call some shell command from vim with like :!ls command. But unfortunately there are some default PATHS that prepends PATHs defined in the original shell. Here is the echo $PATH output in the original shell: /usr/local/heroku/bin:/Users/bogdan/.rvm/gems/ruby-1.9.3-p194/bin:/Users/bogdan/.rvm/gems/ruby-1.9.3-p194@global/bin:/Users/bogdan/.rvm/rubies/ruby-1.9.3-p194/bin:/Users/bogdan/.rvm/bin:/usr/local/bin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/X11/bin:/Users/bogdan/.rvm/bin:/Users/bogdan/bin:/Users/bogdan/.rvm/bin:/usr/local/Cellar/git/1.7.12.2/libexec/git-core:/Users/bogdan/.rvm/bin and shell called within vim: /usr/local/bin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/X11/bin:/Users/bogdan/.rvm/gems/ruby-1.9.3-p194@devauc/bin:/Users/bogdan/.rvm/gems/ruby-1.9.3-p194@global/bin:/Users/bogdan/.rvm/rubies/ruby-1.9.3-p194/bin:/Users/bogdan/.rvm/bin:/Users/bogdan/bin:/usr/local/Cellar/git/1.7.12.2/libexec/git-core:/Users/bogdan/.rvm/bin Why they appeared right there? How can I prevent that and make vim shell has original PATH variable.

  Read the article

• Mac OS ? Assembly Language Esoteria

  - by veryfoolish

  I've been playing around with assembly and object files in general on Mac OS ? and was wondering if somebody could provide some edification. Specifically, I'm wondering what the extra code GCC generates when compiling the C file in the following example does. I have a toy C program so I can comprehend the assembly output. int main() { int a = 5; int b = 5; int c = a + b; } Running this through gcc -S creates the following assembly: .text .globl _main _main: LFB2: pushq %rbp LCFI0: movq %rsp, %rbp LCFI1: movl $5, -4(%rbp) movl $5, -8(%rbp) movl -8(%rbp), %eax addl -4(%rbp), %eax movl %eax, -12(%rbp) leave ret LFE2: .section __TEXT,__eh_frame,coalesced,no_toc+strip_static_syms+live_support EH_frame1: .set L$set$0,LECIE1-LSCIE1 .long L$set$0 LSCIE1: .long 0x0 .byte 0x1 .ascii "zR\0" .byte 0x1 .byte 0x78 .byte 0x10 .byte 0x1 .byte 0x10 .byte 0xc .byte 0x7 .byte 0x8 .byte 0x90 .byte 0x1 .align 3 LECIE1: .globl _main.eh _main.eh: LSFDE1: .set L$set$1,LEFDE1-LASFDE1 .long L$set$1 LASFDE1: .long LASFDE1-EH_frame1 .quad LFB2-. .set L$set$2,LFE2-LFB2 .quad L$set$2 .byte 0x0 .byte 0x4 .set L$set$3,LCFI0-LFB2 .long L$set$3 .byte 0xe .byte 0x10 .byte 0x86 .byte 0x2 .byte 0x4 .set L$set$4,LCFI1-LCFI0 .long L$set$4 .byte 0xd .byte 0x6 .align 3 LEFDE1: .subsections_via_symbols The LCFI1 section seems to contain the actual logic for the program, but I'm not sure what the misc. other stuff is for... also, is there any scheme these labels are following? I'm sorry this is such a vague question. I'd appreciate anything, including being pointed to a resource where I can find out more about this. Thanks!

  Read the article

• Is 1GB RAM with integrated graphics sufficient for Unity 3D on 12.04?

  - by Anwar Shah

  I have been using Ubuntu since Hardy Heron (8.04). I used Natty, Oneiric with Unity. But When I recently (more than 1 month now) upgraded My Ubuntu to Precise (12.04), the performance of my laptop is not satisfactory. It is too unresponsive compared to older releases. For example, the Unity in 12.04 is very unresponsive. Sometimes, it requires 2 seconds to show up the dash (which was not the case with Natty, though people always saying that Natty's version of Unity is buggiest). I am assuming that, May be my 1GB RAM now becomes too low to run Unity of Precise. But I also think, Since Unity is improved in Precise, It may not be the case. So, I am not sure. Do you have any ideas? Will upgrading RAM fix it? How much I need if upgrade is required? Laptop model: "Lenovo 3000 Y410" Graphic : "Intel GMA X3100" on Intel 965GM Chipset. RAM/Memory : "1 GB DDR2" (1 slot empty). Swap space : 1.1GB Resolution: 1280x800 widescreen Shared RAM for Graphics: 256 MB as below output suggests $ dmesg | grep AGP [ 0.825548] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000

  Read the article

• Windows 8 recimg createimage fails with 0x80070002, why?

  - by ezuk

  Running Win8 x64. C is an SSD with lots of free space (200GB). I run: recimg /createimage C:\CustomRefreshImages\Img121105 Output says: Source OS location: C: Recovery image path: C:\CustomRefreshImages\Img121105\CustomRefresh.wim Creating recovery image. Press [ESC] to cancel. Initializing The recovery image cannot be written. Error Code - 0x80070002 The paths specified in the command line are created, and I'm running this in an elevated command prompt, so it's not a permissions issue. I've googled this but could only find worthless results, including a particularly entertaining one where the "solution" included instructions for creating a screenshot (press PrtScreen). Any help would be most appreciated.

  Read the article

• Shutdown in background - PHP

  - by William

  I'm trying to shutdown an Ubuntu machine from PHP and am running into an issue if I want to delay the shutdown. The PHP line I'm using is: exec("sudo shutdown -h +5 &", $output); Where 5 is however many minutes in the future I want to shutdown. My problem is that this won't background and Apache hangs until either the machine is shutdown or someone else cancels the shutdown. shell_exec() has the same result. Is there another way to do this that will return immediately?

  Read the article

• Reading from a staging 2D texture array in DirectX10

  - by Don Reba

  I have a DX10 program, where I create an array of 3 16x16 textures, then map, read, and unmap each subresource in turn. I use a single mip level, set resource usage to staging and CPU access to read. Now, here is the problem: Subresource 0 contains 1024 bytes, pitch 64, as expected. Subresource 1 contains 512 bytes, pitch 64. Subresource 2 contains 256 bytes, pitch 64. I expect all three to be the same size. Debugging output is enabled, but not reporting any warnings or errors. Am I missing something, or might this be some sort of driver issue? Here is the code. The language is Nemerle, but C# and C++ would look almost the same. I have looked through the generated code, and am fairly confident the problem is not language-related. def cpuTexture = Texture2D ( device , Texture2DDescription() <- { Width = 16; Height = 16; MipLevels = 1; ArraySize = 3; Format = Format.R32_Float; Usage = ResourceUsage.Staging; CpuAccessFlags = CpuAccessFlags.Read; SampleDescription = SampleDescription(count = 1, quality = 0); } ); foreach (subresource in [0 .. 2]) { def data = cpuTexture.Map(subresource, MapMode.Read, MapFlags.None); Console.WriteLine($"subresource $subresource"); Console.WriteLine($"length = $(data.Data.Length)"); Console.WriteLine($"pitch = $(data.Pitch)"); cpuTexture.Unmap(subresource); }

  Read the article

• PO Communication in PDF

  - by Robert Story

  Upcoming WebcastsDate: March 29, 2010 Time: 2 pm London, 9:00 am EDT, 6:00 am PDT, 13:00 GMT Click here to register for this sessionDate: March 29, 2010 Time: 9 am London, 4:00 am EDT, 1:00 am PDT, 8:00 GMT Click here to register for this session Product Family: ProcurementSummary This one-hour session is recommended for technical and functional users who would like to know about the PO Communication functionality in procurement. Topics will include: Introduction to PO PDF communication - 11.5.10 Key ConceptsPrerequisites, Scope Overview of PDF document generation PDF solution overviewTechnical Overview of PDF generation Setup steps Triggering Points of PDF generation PO Output for communication - Concurrent programEnter PO form: View DocIsupplier portal/Contracts preview Enhancements PDF Generation in Custom LayoutsAttachments in fax communicationR12 Communication Nontext Attachments through Email Customizing templates Advantages of PDF communication Troubleshooting (Tips) A short, live demonstration (only if applicable) and question and answer period will be included........ ....... ....... ....... ....... ....... .......The above webcast is a service of the E-Business Suite Communities in My Oracle Support.For more information on other webcasts, please reference the Oracle Advisor Webcast Schedule.Click here to visit the E-Business Communities in My Oracle Support Note that all links require access to My Oracle Support.

  Read the article

• Permissions problem on mounting afp drive

  - by Ron Gejman

  I am trying to mount a network drive via AFP on an Ubuntu 10.04 server machine. After installing AFP support, I use the following command: sudo mount_afp afp://USER:[email protected]/directory/ /media/dir This seems to work and it tells me that mounting succeeded. However, when I navigate to /media/dir I get the following error: cd: cfs: Input/output error Permissions in /media are: d????????? ? ? ? ? dir/ drwx------ 12 user 4.0K 2010-10-25 16:08 otherdisk/ So there is a permissions problem here. I eventually want to mount this drive automatically using fstab. What do I need to do to make the disk accessible?

  Read the article

• The remote host closed the connection. The error code is 0x80070057

  - by Jalpesh P. Vadgama

  While creating a PDF or any file with asp.net pages I was getting following error. Exception Type:System.Web.HttpException The remote host closed the connection. The error code is 0x80072746. at System.Web.Hosting.ISAPIWorkerRequestInProcForIIS6.FlushCore(Byte[] status, Byte[] header, Int32 keepConnected, Int32 totalBodySize, Int32 numBodyFragments, IntPtr[] bodyFragments, Int32[] bodyFragmentLengths, Int32 doneWithSession, Int32 finalStatus, Boolean& async) at System.Web.Hosting.ISAPIWorkerRequest.FlushCachedResponse(Boolean isFinal) at System.Web.Hosting.ISAPIWorkerRequest.FlushResponse(Boolean finalFlush) at System.Web.HttpResponse.Flush(Boolean finalFlush) at System.Web.HttpResponse.Flush() at System.Web.UI.HttpResponseWrapper.System.Web.UI.IHttpResponse.Flush() at System.Web.UI.PageRequestManager.RenderFormCallback(HtmlTextWriter writer, Control containerControl) at System.Web.UI.Control.RenderChildrenInternal(HtmlTextWriter writer, ICollection children) at System.Web.UI.Control.RenderChildren(HtmlTextWriter writer) at System.Web.UI.HtmlControls.HtmlForm.RenderChildren(HtmlTextWriter writer) at System.Web.UI.HtmlControls.HtmlForm.Render(HtmlTextWriter output) at System.Web.UI.Control.RenderControlInternal(HtmlTextWriter writer, ControlAdapter adapter) at System.Web.UI.Control.RenderControl(HtmlTextWriter writer, ControlAdapter adapter) at System.Web.UI.HtmlControls.HtmlForm.RenderControl(HtmlTextWriter writer) at System.Web.UI.HtmlFormWrapper.System.Web.UI.IHtmlForm.RenderControl(HtmlTextWriter writer) at System.Web.UI.PageRequestManager.RenderPageCallback(HtmlTextWriter writer, Control pageControl) at System.Web.UI.Control.RenderChildrenInternal(HtmlTextWriter writer, ICollection children) at System.Web.UI.Control.RenderChildren(HtmlTextWriter writer) at System.Web.UI.Page.Render(HtmlTextWriter writer) at System.Web.UI.Control.RenderControlInternal(HtmlTextWriter writer, ControlAdapter adapter) at System.Web.UI.Control.RenderControl(HtmlTextWriter writer, ControlAdapter adapter) at System.Web.UI.Control.RenderControl(HtmlTextWriter writer) at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) Exception Type:System.Web.HttpException The remote host closed the connection. The error code is 0x80072746. at System.Web.Hosting.ISAPIWorkerRequestInProcForIIS6.FlushCore(Byte[] status, After searching and analyzing I have found that client was disconnected and still I am flushing the response which I am doing for creating PDF files from the stream. To fix this kind of error we can use Response.IsClientConnected property to check whether client is connected or not and then we can flush and end response from client. Here is the sample code to fix that problem. if (Response.IsClientConnected) { Response.Flush(); Response.End(); } That’s it Hope this will help you..Stay tuned for more.. Till that Happy Programming!! Technorati Tags: Exception,ASp.NET

  Read the article

• Strange 'locate' behavior and icon changing

  - by Luigi Tiburzi

  I'd like to change the icon of a program called Refit with a custom one. This program has various tools and when I try to change those icons all is ok but then I run the following command: $ locate refit.icns and the output is: $ /efi/refind/icons/os_refit.icns The problem is that I don't have any folder called refind and the path simply doesn't exist. I tried it with both: $ ls and $ sudo ls in the /efi directory. So my questions are actually two: how can I change the icon of that program? And why there is this strange behavior with the locate command? I'm on Snow Leopard 10.6.8. Thanks for your help.

  Read the article

• Dell R510 vs R710

  - by AX1

  Hello, the Dell R510 and R710 can both hold regular configurations (e.g. X5650, 24 GB RAM, etc.) and these usually come out to about the same price. Is there a particular reason why one would choose the R510 over the R710 or vice versa? There really appears a lack of differentiating factors. The only 'major' factor I found, which doesn't apply to me though, is that the R510 can hold up to 12 3.5in HDDs while the R710 (which is slightly more expensive) can only hold up to 6 3.5in HDDs. Maybe you guys have some input and bought either of these machines (or both) to shed some light on other differences and why someone should choose one over the other as the pricing is pretty much the same with my configuration. Thanks!

  Read the article

• Search files for text matching format of a Unix directory

  - by BrandonKowalski

  I am attempting to search through all the files in a directory for text matching the pattern of any arbitrary directory. The output of this I hope to use to make a list of all directories referenced in the files (this part I think I can figure out on my own). I have looked at various regex resources and made my own expression that seems to work in the browser based tool but not with grep in the command line. /\w+[(/\w+)]+ My understanding so far is the above expression will look for the beginning / of a directory then look for an indeterminate number of characters before looking for a repeating block of the same thing. Any guidance would be greatly appreciated.

  Read the article

• Toshiba Satellite laptop connected to HDTV

  - by VANJ

  I have a Toshiba Satellite A505-S6014 laptop running Windows 7 64-bit connected to a Toshiba Regza 42" HDTV with an HDMI cable. The laptop has a 16" display and the screen resolution is set to the maximum/recommended of 1366x768. The display output is set to "LCD+HDMI". The display looks fine on the laptop screen but on the TV it is not a "full screen" display, it leaves a good 3" black border all around all 4 edges. When I switch the display to "HDMI only", it is now too big for the TV screen and some of my desktop icons are no longer visible off to the side. What is the best way to set this up? I guess that since a 16" and 42" displays have different native resolutions, a LCD+HDMI mode is defaulting to the optimal size for the 16". But when I set it to HDMI Only, what is the appropriate resolution for a 42" full screen display? Thanks

  Read the article

• Add a Search Box to the Drop-Down Tab List in Firefox

  - by Asian Angel

  Do you have a lot of tabs open no matter what time of day it is and find sorting through the tabs list frustrating? Then get control back with the List All Tabs Menu extension for Firefox. Before If you have a large number of tabs open using the “Tab List Menu” can start to become a little awkward. You can use your mouse’s middle button to scroll through the list or the tiny arrow button at the bottom but there needs to be a better way to deal with this. After Once you have installed the extension you will notice two differences in the “Tab List Menu”. There will be a search box available and a nice scrollbar for those really long lists. A closer look at the search box and scrollbar setup… Depending on your style you can use the scrollbar to look for a particular page or enter a search term and watch that list become extremely manageable. A closer look at our much shorter list after conducting a search. Definitely not hard to find what we were looking for at all. Conclusion If you are someone who has lots of tabs open at once throughout the day then the List All Tabs Menu extension might be the perfect tool to help you sort and manage those tabs. Links Download the List All Tabs Menu extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Organize Your Firefox Search Engines Into FoldersAdd Search Forms to the Firefox Search BarGain Access to a Search Box in Google ChromeWhy Doesn’t Tab Work for Drop-down Controls in Firefox on OS X?Quick Tip: Spell Check Firefox Text Input Fields TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7? Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox)

  Read the article

< Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >