Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 7/216 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

• Linksys WRT54Gx as Repeater Bridge

  - by Robert Koritnik

  I have a Linksys WRT54Gx router with DD-WRT software working fine. But. Is it possible to use it as a Repeater Bridge when the host router isn't configured to be in the default 192.168.1.1 subnet? I've set everything from these instructions. I've also tried setting repeater router's IP address to be inside host's subnet, setting Gateway + DNS IP addresses... But It still didn't work. Client machines connecting to second router (my Linksys) were configured to use DHCP and also static IPs within host's subnet. Nothing worked. Can anyone tell me how to configure it to make it work?

  Read the article

• WPA Enterprise Wireless Bridge

  - by prestomation

  I live in college housing at a university with wifi available. unfortunately, my bedroom(where I'd like to place my PC) gets little to no reception. I'd like to place a router in the strongest spot and rebroadcast. I understand this can be done with DD-WRT/etc, but this particular network is WPA Enterprise with my own personal username/password. I can't find any concrete evidence that I can get my router to act as a repeater for this encryption. I don't currently have a router to test it on, otherwise this would be easy, I just don't want to buy a router if it will be worthless to me. Thanks for your help

  Read the article

• Can I bridge two wired networks with a Netgear WG602 (v4)

  - by Mr. Flibble

  I have two networks and I want to join them. Only one has a router. The other is currently just a bunch of computers joined via a switch. So it looks a little like this: 1. Router + comp1 + comp2 + wireless ap 2. comp3 + comp4 + Netgear WG602 Is it possible to use the WG602 to connect to the WIFI of the main network (the one with the router) and connect via wire to the 2nd network - therefore allowing the computers on network 2 to use the router on network 1?

  Read the article

• Prevent RDP logon brute force in mikrotik router via winbox

  - by holian

  Masters, I need help, how to config our router to block RDP brute force attacks I would like to set our router to only allow RDP connection from a specified country (our specified IP ranges), plus i need to set up router to block (take ips to black list) and drop brute force attepmst to specified port numbers. I try to set this with changeing the ftp port to rdp port. http://wiki.mikrotik.com/wiki/Bruteforce_login_prevention_%28FTP_%26_SSH Any suggestion tnx. H Current configuration: I try to configure the router via Winbox. I set some NAT rules (from dyndns to local address, rdp port) In the filter rules tab: I'm not sure this configuration should do the trick?! Is the content text "530 login incorrect" is fit for RDP connection to? Because in the tutorial used for filtering FTP connection. How to set router to allow RDP attempts from specified IP ranges? Thank you // New config

  Read the article

• How to Bridge Two Ethernet Ports on Mac OS X

  - by Rabarberski

  How can I bridge two wired ethernet interfaces on Mac OS X (e.g. the current MacPro comes with two ethernet ports)? Googling turned up (e.g. this Apple forum post and this openvpn post) that this is fairly easy on Linux (using the brctl command) and under Windows (via Network Connections right-click Bridge Connections), but how is it done under Mac OS X? BTW: There also doesn't seem to be a macport for brctl ('port search brctl' didn't turn up any results) Note: I don't want to have 'internet sharing', which creates a new network (by handing out network addresses in a new range). I want to really 'bridge' two interfaces so to keep the same network subnet.

  Read the article

• Share Pc' s wifi internet connection to router and spit it out trough it

  - by Maken

  Basicly im trying to share the an internet connection that i receive through wifi from my bestfriend's place to my place and Extend it trough a router for my consoles and other computers in my household i have 1 pc with Wifi /Ethernet , one router "DD-wrt"ed" Schema is like this Internet -----Modem------- (Friend's)Router -----to my PC through Wifi (Ics)---- to Router(2) through lan----- to Computer 1 (over lan or wifi etc...) ------ Computer 2 (over lan or wifi etc...) i want the computer 1 and 2 to have internet from Router(2) if its not clear enough il try to give more details but a little help would be greatly appreciated

  Read the article

• Netgear router-speed problem after XBox use

  - by John Dudley

  When my son is at my place at the weekend, he plays XBox Live over the internet, using my wireless network (Netgear 'g' type router). This usually thrashes & crashes the router to the extent I have to hard-boot it to get it working again. However, after this weekend, on my two laptops, I'm left with the problem that the router is working, but I'm only getting 0.38Mbps out of it, at all times of the day. I've tried hard-booting the router, but no difference. Could this be a knock-on effect of the Xbox use? I can't believe the router could be damaged, but working slower? Is that possible? Tiscali haven't come back to me yet on any 'network' issues. Thanks in advance

  Read the article

• Modify .htm files on wireless router

  - by mdeitrick

  What am I trying to do? I am attempting to access the .htm files on my wireless router to modify the look and feel of the Netgear GENIE webpage(s). What have I done? I've read several articles on eHow and Instructables that detail how to setup your router as an FTP server, since I figured the best way to access the files would be through FileZilla. Setting up an FTP server through my router doesn't sound like what I should do to accomplish my task... or perhaps it is? I've also read the documents provided by Netgear for getting started and setting up functionality on the router. Maybe I overlooked something? My specifications Netgear router WNR2000v3 FileZilla v3.8.1 UPDATE: Since someone voted to close this question I'll clarify what I'm asking for... At the present I am dissatisfied with the current UI/webpage look when logging into routerlogin.net. Furthermore I would like to make changes to the admin dashboard.

  Read the article

• Linksys router with multiple external IP's

  - by Adrian Mester

  In an office I've got a network connection with 5 external IPs and a Linksys router (I'm not 100% percent sure of the model). I need 4 of those 5 IPs to be routed to a server, and the fifth to be shared between the other computers at the office. This can probably be done using a switch in front of the router. Connect the server and the router to the switch, and let the router handle the rest of the network. Is there a way to configure the router to route the 4 IPs to the server, and create an internal network the the other computers at the same time?

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• Router loses connection to internet randomly

  - by tvanover

  I have a Belkin wireless G plus Mimo router and it randomly loses the connection to the internet. It seems to happen for a second or two, not enough to impact day to day browsing. But enough to disconnect games, or stall videos I am watching. It happens whether I am plugged into the router or connecting via wifi. I am unsure if it is my router or Comcast that is causing this issue. If I connect a computer directly to the modem the problem never occurs, so that tells me it is probably the router. But I also had a Netgear wireless router WGR614, and it had the same problem. I don't know where to start looking for the source of the problem. What logs should I be combing through? All my machines are win 7 of varying versions.

  Read the article

• Bridge Intrusion Prevention Vyatta

  - by Steve

  I am trying to create a bridge with ThreatStop, IPS and block a few ports. This bridge will sit in front of my servers. All is working apart from the IPS. I have read the documentation on configuring IPS, I have something configured that it hasn't complained about and nothing is logged so I believe that it isn't working. Is it possible to set-up IPS on a vyatta bridge? Also is it possible to read the logs/events with Snorby? I have also posted this on the Vyatta forums

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• bridge to share WiFi internet connection over eth0

  - by rubo77

  In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

  Read the article

• Credentials needed for BT line on Netgear router

  - by Bali C

  I have recently bought a new Netgear router to replace my current BTHomeHub as it doesn't support wireless. I did buy a WAP but figured it would be easier to use a router with wireless built in. (It's a modem/router combo). I have got as far as setting up the router on the web interface, but then it asks for a username and password to connect to the net, I can only assume this is for the phone line? I have tried some passwords I could find written down but they don't work, the internet light comes on and then when the creds fail it goes off. I have been on the homehubs web interface and been through all the settings it has to find the credentials it is using which obviously work, but no joy. Is there anything obvious I am missing, or is there a way I can retrieve my settings from my existing router? Any pointers will be very appreciated.

  Read the article

• Get into the router setting without knowing the password [on hold]

  - by Aron

  So my father has changed the router passwords, and programed the router to turn my wifi connection off automaticly at some times, for example at night. I wanted to know if there is any way I can trick this feature? Can i change my ip in some way, the router won't recognize my ip, so my new ip would have internet connection? Is it any way i can get into the router settings and turn that feature off without knowing the router password? Would be happy if I could get replies as soon as possible!

  Read the article

• Using the Onboard VGA output with a PCIe video card. Both nVidia

  - by sebikul

  I have 2 video cards, one On board, a nVidia 6150SE nForce 430 and a PCIe nVidia GeForce GT 220 1GB DDR2 RAM I have already configured the PCIe card to use the dual monitor feature, using the VGA and HDMI ports, but now I want to add a third monitor, using the On board VGA port I have managed to enable the On board graphics processor, which is taking 400MB of ram, but I cant manage to use it, nvidia-settings does not detect it, like it's not usable (but is there) My questions are the following: How can I manage to get the On board VGA display to work together with the PCIe graphics card? If possible, how can I recover those 400 MB the on board card is taking (even without being used) or how can I get it to use the PCIe card available memory? System Details: Linux 2.6.35-28-generic i686 Ubuntu 10.10 (All updates installed) NVIDIA Driver Version: 260.19.06 (Official) If more info is needed please let me know. Here is the lspci output when the On board card is disabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) And this is when both are enabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) Output of lshw -class display: *-display description: VGA compatible controller product: GT216 [GeForce GT 220] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:02:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:df000000-dfffffff memory:c0000000-cfffffff memory:da000000-dbffffff ioport:ef80(size=128) memory:def80000-deffffff *-display description: VGA compatible controller product: C61 [GeForce 6150SE nForce 430] vendor: nVidia Corporation physical id: d bus info: pci@0000:00:0d.0 version: a2 width: 64 bits clock: 66MHz capabilities: pm msi vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:22 memory:dd000000-ddffffff memory:b0000000-bfffffff memory:dc000000-dcffffff memory:deb40000-deb5ffff If what I'm looking for is not possible, please tell me, so I can disable the On board card and recover those 400MB of wasted RAM Thanks for your help!

  Read the article

• Z77 Motherboard with i7-2600K cpu, what will not work?

  - by Mxx

  I'm building a new system. So far I think I narrowed it down to Gigabyte GA-Z77X-UD5H (Z77 Ivy Bridge chipset) motherboard. I was planning to get i5-3570K(Ivy Bridge) cpu, but now I can get i7-2600K(Sandy Bridge) cpu for free. It is my understanding that Ivy Bridge platform brings support for PCIe3 and (additional?)USB3 ports. If I were to put SB cpu into IB motherboard, what is going to happen to PCIe3 slot? Will it not work at all or downgrade to PCIe2? Also, what is the situation with USB3 ports?

  Read the article

• How do I use a Zyxel P660 router as just modem so that I can connect a WRT54GL router in cascade?

  - by Kenji Kina

  I have a Zyxel P660HW-t1 v2 router (which has a DSL port) and a WRT54GL router (which does not) and the exact same situation as in this thread (UPDATE: the connection between both devices is the important part, since I have been able to set the zyxel router to act as bridge by itself quite nicely. I have accessed my internet connection directly through a PC using PPPoE without any problems, the issues arise when I try to connect the WRT54GL router between the zyxel "modem" and my PCs). I've been trying to use my Zyxel P660 as a modem only: Setup P660 to bridge mode. Changed WRT54GL's IP address to 192.168.2.1 to avoid a conflict on the network. Configured the PPPoE settings as required on WRT54GL. The thing is that when I connect the Zyxel modem/router on the WRT54GL's internet port the light doesn't turn on. I can confirm that this port has been working ok, so I'm not really sure what's going between the devices. I checked several settings such as IPs, tried disabling DHCP on Zyxel/Linksys, Firewall on both and still nothing. Also, I tried connecting Zyxel directly to a computer in bridge mode and dialed successfully. I have even posted a question here before, thinking that what I asked there was the only thing I needed to get things done. Unfortunately it wasn't, and the guy that solved his issue didn't give enough details in his post (and is quite unlikely to give more details since he was an anonymous user). For one, I don't know how to do this part: connected to the Zyxel through telnet and forced LAN port 1 to be at 100mb as well I can't find the option that does this on the zyxel router. Not through telnet or the web admin. Can anyone help me solve this?

  Read the article

• Modem doesn't seem to pass internet connection to router

  - by Vian Esterhuizen

  I was supplied a Cisco DPC3825 modem by my ISP and use a Cisco E4200 as my main router. Today the Internet just stopped working, just out of the blue, I can't think of anything that would have triggered it. It's been working pretty good for the past month except for a few random blips here and there. After some trouble shooting I realized that a direct wired connection to the modem would get me Internet access but if I was wired to the router as I was before I would have no connection. Assuming it was router I connected a TP-Link WR841N but it had the exact same problem. Also, connecting to the router via Wi-Fi from multiple devices will connect me to the router but I still can't get access to the Internet. From these test, it seems that the modem just won't send Internet through to the router but is clearly connecting and able to directly connect to my PC. What I've Tried A full reset and factory reset on the E4200 A full reset on the modem (but I believe my ISP has remote access to the modem because the passwords and so on are always set back). My ISP has remotely reconfigured the modem What I Should Try What else can I try? What should I do to try to narrow down the issue? Can you figure out what the problem might be based on this information?

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

• Router failover not detecting outside interface link lost

  - by Matt

  Suppose I have two routers configured in master/slave configuration. They look something like this (addresses are not real ones) 123.123.123.10 <===> [eth0] Router 1 (10.1.1.2) [eth1] ===> +----------+ | 10.1.1.1 | ===> LAN 172.123.123.10 <===> [eth0] Router 2 (10.1.1.3) [eth1] ===> +----------+ The 10.1.1.1 is the default route for the Network (10.1.1.0). What's slightly different in this config to other's I've seen is that I don't have an external virtual IP. Also, the 10.1.1.1 addresses are in real life, public IP's (not private ones shown here). This is more of a router setup than a firewall setup so I'm not using NAT here. Now the issue that I'm having is that I can't see any way to configure UCARP or VRRP to monitor both eth0 & eth1 and fail over to the backup router should either of them go down. What I'm seeing is that if Router1 is the master and I unplug eth0 on router1, it doesn't fail over to router 2. However, it will if instead I unplug eth1 of router 1. In VRRP I see there is a cluster group, but it seems that for this to work you need to have virtual ip's or vrrp instances rather than actual interfaces assigned to it. I hope my explanation is clear. How do I get around this?

  Read the article

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >