Search Results

Search found 11524 results on 461 pages for 'insurance networking news'.

Page 70/461 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

  • Intermittent internet connectivity

    - by Rob Oplawar
    UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

    Read the article

  • How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

    - by user12285
    Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • WiFi slow sometimes, reboot helps, how do I debug it?

    - by January
    Ubuntu 12.04.1 with all updates installed. Laptop Lenovo Thinkpad X230 with Intel Corporation Centrino Advanced-N 6205. WiFi sometimes becomes extremely slow. Often this occurs when I wake the system from suspend and connect to a different network. I find no obvious clues in system logs. /etc/init.d/network-manager restart doesn't help, but a reboot does. How can I go on with debugging this issue? In specific, which parts of the system should I try to restart (without a complete reboot)? I know of problems with Intel WiFi (see for example this question and the instructions here), but if that was the problem, I would expect the WiFi to be slow at all times, and not just sometimes. Also, I have a gut feeling that it might be a DNS issue (for example, getting a page from a known server is faster than accessing a new server), but I don't know how to tackle it. Update: despite numerous updates in the meanwhile, I still observe this behavior. It happens always when I access my WiFi router at home after returning from work; when I reboot my laptop, the connection speed is good again.

    Read the article

  • Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

    - by Constant Dean
    I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

    Read the article

  • How to perform game object smoothing in multiplayer games

    - by spaceOwl
    We're developing an infrastructure to support multiplayer games for our game engine. In simple terms, each client (player) engine sends some pieces of data regarding the relevant game objects at a given time interval. On the receiving end, we step the incoming data to current time (to compensate for latency), followed by a smoothing step (which is the subject of this question). I was wondering how smoothing should be performed ? Currently the algorithm is similar to this: Receive incoming state for an object (position, velocity, acceleration, rotation, custom data like visual properties, etc). Calculate a diff between local object position and the position we have after previous prediction steps. If diff doesn't exceed some threshold value, start a smoothing step: Mark the object's CURRENT POSITION and the TARGET POSITION. Linear interpolate between these values for 0.3 seconds. I wonder if this scheme is any good, or if there is any other common implementation or algorithm that should be used? (For example - should i only smooth out the position? or other values, such as speed, etc) any help will be appreciated.

    Read the article

  • No Sound from Shared Media

    - by Travis
    I have a shared media folder that I have all of my mp3's in. When I try to play them using Ubuntu, I get no sound, but the media player (Rhythmbox, Exaile, etc) display that they are playing the file, it looks like everything is playing but no sound. I have checked and rechecked the volume levels of the system and each application and I see no issues. If I move a file to the local drive, it plays just fine. I do sound checks while the file is playing and I get audio (front left, front right) from the test but not from the media file that I am playing. Any help would be greatly appreciated.

    Read the article

  • Wireless ad-hoc network between Ubuntu and MS Windows

    - by nixnotwin
    I have setup a wireless ad-hoc connection between two laptops: one running ubuntu and the other MS XP. I have assigned static IP to both the laptops and both get connected quite easily. I can access all ubuntu services like ssh, squid, samba from the laptop running MS Windows. But from Ubuntu machine I cannot access any Windows services like shared directories etc. The Windows machine doesn't even respond to ping requests from ubuntu.

    Read the article

  • accessing files on a shared folder via IIS

    - by Darkcat Studios
    Im not sure if this suits stackexchange, serverfault or here... so i'll go with here for a start. I'm having issues setting up a network share to be accessed by IIS, all I need to do is read/write files on the Other server. We have 2 servers set up (Both 2008 R2 & IIS 7.5), one is the WEB server, which is externally accessible and NOT part of the domain. We also have an Intranet server which has no internet connectivity and is part of the domain. These 2 servers can talk to each other happily, I have the SQL server on the WEB server shared across to the intranet server so that the web content is editable from the intranet. I can share a folder on the web server (say, wwwroot/Images/) and connect to it from the intranet server, even have it as a mapped drive (but i know thats not going to work for IIS to access it), So there seems not to be a connectivity issue. I can also set up a Virtual folder in IIS on the Intranet server - this is where it gets annoying - I cant connect using pass-through authentication because there is no suitable user on the web server (which is not on the domain). If i set up a user on the web server, eg Intranet_USR, and give it appropriate rights to the folder, files and share, i can connect, but only view folder contents in IIS, not read, although that user has read privileges!! Any help much appreciated!

    Read the article

  • When Ubuntu Server restarts eth0 Doesn't come back up

    - by JoelGsus
    Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

    Read the article

  • connecting ubuntu with 7 via network cable

    - by VeXe
    i was tryin to connect my ubuntu toshiba satalite L650 laptop with my desktop via a network cable so that i can share things and remotely control the desktop from the laptop, i googled the problem out and found a guide page , i followed all the steps , i installed samba, i had the two computer have the same workgroup name , i had everything correct, but i still dont see connection estbalished between the two computers, (neither one is visible to the other) what is missing ? thanx in advance.

    Read the article

  • how to find 3g modem signal strength with out AT commands?

    - by neckTwi
    when i try to find signal strength of my modem using AT+CSQ, the usb device is locked by the network manager. To find the signal strength with AT+CSQ i have to first disable network connection using #nmcli nm wwan off to unlock the device inode /dev/ttyUSBX. Is there any nmcli option to get signal strength or any other option? EDIT The gdbus object for NetworkManager don't have any method like getSignalStrength. Network manager is locking device file preventing to use AT commands. nm-applet was able to display signal strength in system tray. so there should be a way to get signal strength form network manager! nmcli is command line counter part of nm-applet. Can i get signal strength using nmcli? nothing about signal strength is mentioned in its man pages.

    Read the article

  • Configure application priority to access the network

    - by Mario
    I noticed that when I am running applications such BitTorrent all the other applications have trouble accessing the network. I am sure it would be possible to limit BitTorrent's network usage but what I really want is to be able to set priorities to applications (or protocols) accessing the network. For example, let's say I put max priority for the browser (or http) and then, no matter how much bandwidth was using at the time, the http packets would always go through. Is this possible? Is there an application for Ubuntu to do this or a way to configure this on Ubuntu directly?

    Read the article

  • no wifi after grub 2 crash

    - by Omu
    on ubuntu 10.10 I used StartupManager to set windows 7 as the default boot, also chosen the 1024x768 resolution, 16 bit, time: 3sec, and checked "show splash screen". after the restart there was no GRUB menu at all, windows 7 booted, and in windows the clock was 0:03 instead of 10:03, also the wifi doesn't sees any connections anymore I reinstalled ubuntu 10.10 so the GRUB menu is back, changed the clock back from BIOS, but my wifi doesn't sees any connections in windows nor in ubuntu (I write this from another computer)

    Read the article

  • Computer becomes unreachable on lan after some time

    - by Ashfame
    I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

    Read the article

  • ubuntu 12.04 server doesn't resolve local domain name

    - by jdog
    After apt-get upgrade this morning, my Ubuntu 12.04 web server does no longer resolve a domain name hosted on it. I also received the error message: "resolvconf: Error: /etc/resolv.conf isn't a symlink, not doing anything." I found this question Network Manager not populating resolv.conf but the solutions provided there did not resolve the problem. Creating the symlink in fact caused websites to load very slowly, so I assume there is some sort of (reverse?) DNS lookup not working, when I create the symlink.

    Read the article

  • audio and video data in RTP

    - by Banana
    Suppose a user wants to transmit both audio and video to another user, whose formats are AMR for audio and H.264 for video. Does the user have to transmit audio and video packets always separately? Meaning that it is not possible to mix audio and video within the same RTP packed, is that correct? If this is true I guess the RTP protocol will need to know the SSRC of both audio and video to be able to check the sync of the two streams.

    Read the article

  • ubuntu nic card issue

    - by Blainer
    I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

    Read the article

  • Network strange problem

    - by Ali
    I have a CPanel server with 5 IPs and a few domains. During night, access to main domain through HTTP return 324 no response many times. After several refresh it comes but many assets won't load and return 324. Using HTTPS is fine. During day HTTP is also fine. But another domain on that very sever works fine all the day through HTTP. The server DNS are ns1 and ns2 of the first domain. Second domain is on the shared IP and first domain has a dedicated IP. I cant resolve the problem :( and appreciate any help so much!

    Read the article

  • How to set system-wide proxy address using shell script?

    - by skg
    I want to set system Proxy address through my Qt application. So i was wondering if i could write a script which can be executed by my application every time to change the proxy address. I tried : #! /bin/sh echo "# Generated by Application" export $1 echo "Proxy Address ${1} but this script was not successful. I think it was unable to execute "export" command. Can anyone help me resolving this issue ?

    Read the article

  • mount remotely mybook live network drive

    - by bob
    I have a mybook live western digital 1TB hard disk connected to fritzbox 7270 router in office. When I am in the office, I can mount this drive to ubuntu since I have added to the etc/fstab file: //192.168.178.30/user /home/user/DISK cifs auto,iocharset=utf8,user=user%password 0 0 Is there a similar, easy & safe way, to do the same when I am out of the office using the static IP of the fritzbox router? I have already added tcp port forwarding in the router for ports 8080 (to 80 of the disk) and 8443 (to 443 of the disk). Thank you in advance

    Read the article

  • Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

    - by Mr. Smileys
    I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

    Read the article

  • UFW blocking random packets on 443

    - by s2jcpete
    All, I have UFW setup to allow traffic on port 443. It works as expected, though I have a large amount of UFW Block log entries. To Action From -- ------ ---- 80 ALLOW Anywhere 443 ALLOW Anywhere 22222 ALLOW Anywhere 80 ALLOW Anywhere (v6) 443 ALLOW Anywhere (v6) 22222 ALLOW Anywhere (v6) However in my syslog file I see this: [UFW BLOCK] IN=eth0 OUT= MAC=XXX SRC=<foreignip> DST=<serverip> LEN=40 TOS=0x00 PREC=0x00 TTL=116 ID=22025 DF PROTO=TCP SPT=49622 DPT=443 WINDOW=0 RES=0x00 ACK RST URGP=0 About 30 or so seconds later pound (which I'm using for SSL decryption and port redirection) throws a connection timed out messsage. I'm assuming this is because UFW is blocking the packet. I'm at a loss as to an explination. Could the packet be malformed or something, is this normal? Edit - I have since changed the /etc/defaults/ufw and set ipv6=no, so the v6 rules are no longer in the mix. The server is still showing the block / connection timed out behavior though. The new ufw status output is: Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 80 ALLOW IN Anywhere 443 ALLOW IN Anywhere 22222 ALLOW IN Anywhere

    Read the article

  • Multiplayer tile based movement synchronization

    - by Mars
    I have to synchronize the movement of multiple players over the Internet, and I'm trying to figure out the safest way to do that. The game is tile based, you can only move in 4 directions, and every move moves the sprite 32px (over time of course). Now, if I would simply send this move action to the server, which would broadcast it to all players, while the walk key is kept being pressed down, to keep walking, I have to take this next command, send it to the server, and to all clients, in time, or the movement won't be smooth anymore. I saw this in other games, and it can get ugly pretty quick, even without lag. So I'm wondering if this is even a viable option. This seems like a very good method for single player though, since it's easy, straight forward (, just take the next movement action in time and add it to a list), and you can easily add mouse movement (clicking on some tile), to add a path to a queue, that's walked along. The other thing that came to my mind was sending the information that someone started moving in some direction, and again once he stopped or changed the direction, together with the position, so that the sprite will appear at the correct position, or rather so that the position can be fixed if it's wrong. This should (hopefully) only make problems if someone really is lagging, in which case it's to be expected. For this to work out I'd need some kind of queue though, where incoming direction changes and stuff are saved, so the sprite knows where to go, after the current movement to the next tile is finished. This could actually work, but kinda sounds overcomplicated. Although it might be the only way to do this, without risk of stuttering. If a stop or direction change is received on the client side it's saved in a queue and the char keeps moving to the specified coordinates, before stopping or changing direction. If the new command comes in too late there'll be stuttering as well of course... I'm having a hard time deciding for a method, and I couldn't really find any examples for this yet. My main problem is keeping the tile movement smooth, which is why other topics regarding synchronization of pixel based movement aren't helping too much. What is the "standard" way to do this?

    Read the article

  • atheros ar8161 not recognized

    - by Paul
    Apparently I am not the only one with this problem. This was my solution, but it did not work, of course. I downloaded the tar from another computer. I found the file of the atheros driver that I needed which is apparently atl1c. I put that file on my ubuntu desktop. I ran the following in the terminal: cd ~/Desktop atl1c make sudo make install I am sure that some of you will find this code laughable, but isn't there a simple code I could use once I have the atl1c folder on the desktop?

    Read the article

  • Multicast in Ubuntu

    - by iwant2learn
    Can some one please explain the steps required to configure a multicast in Ubuntu? I have a simple program taken from Internet. I get errors when I execute the client program. I get the error as: Opening datagram socket....OK. Setting SO_REUSEADDR...OK. Binding datagram socket...OK. Adding multicast group error: No such device: When I execute the server program I get the error as: Opening the datagram socket...OK. Setting local interface error: Cannot assign requested address I am using Ubuntu to run the program. I have two different laptops but connected via the same network. I am using wireless network to perform the above operation.

    Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >