Search Results

Search found 11524 results on 461 pages for 'insurance networking news'.

Page 73/461 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Wired card not connecting after trying to connect

  - by Mike

  I have an Ubuntu 12.10 PC. When I plug in my internet cable it starts connecting and after a minute it says it can't connect. I tried different cables but nothing works. Wlan works. I think it's the network driver but I don't know how to install/update it. Here's the ifconfig info (if it helps): eth0 Link encap:Ethernet HWaddr 00:01:6c:39:2a:8d inet6 addr: fe80::201:6cff:fe39:2a8d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2011 errors:0 dropped:362 overruns:0 frame:0 TX packets:586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:175452 (175.4 KB) TX bytes:147211 (147.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9779 errors:0 dropped:0 overruns:0 frame:0 TX packets:9779 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8460080 (8.4 MB) TX bytes:8460080 (8.4 MB) wlan0 Link encap:Ethernet HWaddr 08:10:74:35:99:9d inet6 addr: fe80::a10:74ff:fe35:999d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1790 errors:0 dropped:0 overruns:0 frame:0 TX packets:3250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:401664 (401.6 KB) TX bytes:2898773 (2.8 MB)

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• Lag compensation with networked 2D games

  - by Milo

  I want to make a 2D game that is basically a physics driven sandbox / activity game. There is something I really do not understand though. From research, it seems like updates from the server should only be about every 100ms. I can see how this works for a player since they can just concurrently simulate physics and do lag compensation through interpolation. What I do not understand is how this works for updates from other players. If clients only get notified of player positions every 100ms, I do not see how that works because a lot can happen in 100ms. The player could have changed direction twice or so in that time. I was wondering if anyone would have some insight on this issue. Basically how does this work for shooting and stuff like that? Thanks

  Read the article

• Bluetooth broadcasting realtime - is it possible

  - by user69961

  Is it possible to broadcast data via bluetooth to one ore more connected devices? I mean that each phone will be master and slave at the same time and each phone will broadcast data that should be received by all other phones. Or is the only possibility to use a "client-server"-like topology; one phone acts as a server and listens to all clients and then sends data from each client to the rest of clients in the network? Which variant should be more effective? If broadcasting is possible then the same implementation can be used for all devices and if one device will die communication between rest of network can continue. And also will there be enough to send one message per device - not message from each device to server and then back to all devices. Am I right?

  Read the article

• How can I use smbclient to connect to Windows shares by hostname when a firewall is enabled?

  - by skyblue

  I can't connect to file shares on Windows computers using smbclient -L //hostname when the firewall is enabled. This occurs whether I'm using ufw (which allows outgoing traffic and replies back in with the default configuration) or iptables (where I'm allowing outgoing traffic and replies back in with iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT). However, smbclient -L //ip-address works whether the firewall is enabled or not. I also tested this against a Samba server running on Ubuntu and again smbclient -L //hostname does not work when the firewall is enabled, but smbclient -L //ip-address works whether the firewall is enabled or not. For reference, here are the iptables rules I used during testing: *filter :INPUT DROP [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -d 224.0.0.251/32 -p udp -m udp --dport 5353 -j ACCEPT COMMIT

  Read the article

• how to map a network drive [duplicate]

  - by acquacheta

  This question already has an answer here: Correct way of mounting a Windows share 1 answer I hope someone can help me.. I'm trying to connect with my university remote filestore, but I can't make it work.. Here is explained what to do on Windows or Mac, and here I found a guide about how to do it with ubuntu, but it's not working to me (at the end of all the steps, I can't access to the mounted folder). I can access to the storage through Konqueror (I'm using KDE), but I would like to access to it also without it. Any suggestion?

  Read the article

• What are different ways to reduce latency between a server and a web application? [closed]

  - by jjoensuu

  this is a question about a web application that provides SOAP web services. For the sake of this question, this web app is hosted on a server SERVER B which is located in California. We have an automated, scheduled, process running on a server SERVER A, located in New York. This scheduled process is supposed to send SOAP messages to SERVER B every so often, but this process typically dies soon after starting. We have now been told by the vendor that reason why the process dies is because of the latency between SERVER A and SERVER B. The data traffic is routed through many diffent public networks. There is no dedicated line between SERVER A and SERVER B. As a result I have been asked to look into ways to reduce the latency between SERVER A and SERVER B. So I wanted to ask, what are the different ways to reduce latency in a situation like this? For example, would it help to switch from HTTPS to some other secure protocol? (the thought here is that perhaps some other alternative would require fewer handshakes than HTTPS). Or would a VPN help? If a VPN would reduce the latency, how would it do that? NOTE: I am not looking for an explicit answer that would work in my specific situation. I am more like looking just for a simple list of what technologies could be used for this. I will still have to evaluate the technologies and discuss them internally with others, so the list would just be a starting point. Here I am assuming that there exists very few ways to reduce latency between two servers that communicate across public networks using HTTPS. Feel free to correct me if this assumption is wrong and please ask if there is a need for specific information. NOTE 2: A list of technologies is a specific answer to the question I stated in the title. NOTE 3: Its rather dumb to close this question when it is after all about me looking for information and furthermore this information can clearly be useful for others. Anyway luckily there are other sites where I can ask around. StackExchange seems to attached to their own philosophical principles. Many thanks

  Read the article

• Wifi works perfectly on Windows, but drops on Ubuntu

  - by alecRN

  I have a dual-boot computer with Windows XP on one partition and Ubuntu 10.10 on the other. In Windows XP I can connect to a hidden wireless network (WPA-PSK AES) perfectly, and I was finally able to install the driver for the adapter on Ubuntu (RNX-N180UBE, hardware id RTL8191SU). It works fine when I first boot the computer and log in, but then after a few minutes the network suddenly stops working completely. If I try to reconnect it, the network manager claims to have connected, but in actuality it's still down. At some points, I have been able to connect to a public network even while the private network didn't work, but that eventually wouldn't work at all either.

  Read the article

• What data-structure/algorithm will allow me to send a list of key/value dictionaries using the least amount of bits?

  - by user12365

  I have server objects that have corresponding client objects. The data to be kept in sync is inside the server object's key/value dictionary. To keep the client objects in sync with the sever objects, I want the server to send the key/value dictionary every frame for each object. What data-structure/algorithm will allow me to send a list of key/value dictionaries using the least amount of bits? Bonus constraint 1: For each type of object, the values of some keys change more often than others. Bonus constraint 2: Memory usage on the server side is relatively expensive.

  Read the article

• Ubuntu 12.04 - no wireless network recognized

  - by Itai

  I just installed Ubntu 12.04 along with WIN7 on the same laptop - Dell Vostro-3560. Now, on Win7 i can access to different wi-fi networks. However, when i am logging onto the Ubuntu section (after re-starting my laptop) - an error message appears: "Disconnected - you are now offline". When i take a look at my network menu (in the upper bar on the screen), i see that no network is found (and i have a few of them in the area...). I tried to look around but really could not find a concrete practical solution to this specific problem, would appreciate any solution from anyone out there that had this problem and solved it. Thanks... Itai

  Read the article

• How do I fix my ethernet card losing network connection every few minutes with kernels 3.8.x?

  - by igoryonya

  I'm using Ubuntu 13.04. My laptop is Acer Aspire one 722-c58rr, and my ethernet card works for a few seconds at a time with kernels 3.8.x, however, kernels 3.5.x and below worked fine. On kernels 3.8.x, it works fine after boot for about a minute, then it looses network connection. When pinging to some address, it says: network address is unreachable, but it can ping it's own address. The address is statically configured. Everything was working fine before. I went to vacation, where I used WiFi and 3G connections, so I didn't notice that the problem occurred. Came back home, plugged in into the ethernet. It worked for a minute then stopped. Rebooting commutator fixed the problem. Tried to connect to a different commutator, same problem. Unplugging and plugging the cable fixes the problem for another minute. Disconnecting eth in Network manager and reconnecting it again, does the same thing. WiFi has no such problem. Tried to use a different cable that works fine on another computer, the same problem. Tried to boot with the lower kernel version, the same problem was happening until I got to the version 3.5 of the kernel series. Everything works fine on the kernel 3.5.x, but I don't want to miss out on the new kernel's features. Executing commands, when booted with 3.8 kernel series, give the following results: lspci| grep -i eth: 06:00.0 Ethernet controller: Qualcomm Atheros AR8152 v2.0 Fast Ethernet (rev c1) dmesg| grep eth1: [ 89.548291] atl1c 0000:06:00.0: atl1c: eth1 NIC Link is Up How do I fix it, while staying in the new kernel version?

  Read the article

• Network disabled on some wake-ups on saucy laptop

  - by Arild

  Since I upgraded to Saucy Salamander 13.10, with every third suspend or so, the network is disabled and I'm unable to re-enable it. I've had to reboot to make it run again. The network menu will have the option Enable network but clicking it will only produce a tick in the menu item, nothing else changes. How can I make it enable automatically after suspend? In the meantime, is there a workaround to at least manually re-enable it? The PC is a Lenovo IdeaPad S205 using drivers r8169 and rt2800pci.

  Read the article

• Can't access some websites using Ubuntu 13.10

  - by Adame Doe

  Something's wrong with Ubuntu. Since I've upgraded to 13.10, I can't access some websites for no apparent reason. I've tried everything imaginable to solve this problem : Made sure that MTUs are the same, Disabled IPv6 in both the network manager and used browsers, Deactivated my network keys, DMZed my computer, Used other DNS like Google and OpenDNS, Checked that no firewall was running my computer ... And it's the same result. I even tried to reinstall Ubuntu a couple of times, but no luck. The most annoying thing about it is I can't access wordpress.org! So, there's no way it could be an ISP restriction of some kind. When I use a VPN, I can access pretty much anything. I'm really frustrated because I have to use wordpress.org very often. Any clue? ifconfig adame@adame-ws:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:3d:b0:7c inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::226:18ff:fe3d:b07c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8024 errors:0 dropped:0 overruns:0 frame:0 TX packets:7966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:684480 (684.4 KB) TX bytes:616608 (616.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8222 errors:0 dropped:0 overruns:0 frame:0 TX packets:8222 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:568269 (568.2 KB) TX bytes:568269 (568.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:70:40:85:eb inet addr:192.168.2.3 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::219:70ff:fe40:85eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1464 Metric:1 RX packets:123705 errors:0 dropped:0 overruns:0 frame:0 TX packets:98141 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:94963545 (94.9 MB) TX bytes:10387470 (10.3 MB) /etc/hosts 127.0.0.1 localhost 127.0.1.1 adame-ws ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters tracepath wordpress.org 1: adame-ws.local 0.092ms pmtu 1500 1: 192.168.2.1 1.300ms asymm 2 1: 192.168.2.1 1.060ms asymm 2 2: no reply 3: no reply 4: no reply 5: no reply 6: no reply 7: no reply 8: no reply ... keep on going like that ping wordpress.org adame@adame-ws:~$ ping wordpress.org PING wordpress.org (66.155.40.250) 56(84) bytes of data. --- wordpress.org ping statistics --- 10 packets transmitted, 0 received, 100% packet loss, time 9071ms

  Read the article

• Can't connect to windows 7 ad-hoc network

  - by Nikolaj

  Good day! I have installed ubuntu 12.04 on my laptop and I need to have network connection on it. Have a desktop PC, where I've created ad-hoc wi-fi network(Windows 7) and can't connect to it. So, problem: I see my network in the list of networks to connect, but I cant connect to it because it's grey color and not active(can't click on it). Could somebody help me to solve that problem? Thanks in advance!

  Read the article

• Can't access windows 7 shared files on Ubuntu 11.10

  - by Corey

  I just set up ubuntu 11.10 and Samba. I got it to access shares on a Vista machine, but when I try to access the shares on a windows 7 machine it asks for a Username, Domain, and Password. I have no password set up on the windows 7 machine so I put in the username, and domain try to connect and the password prompt keeps appearing...also tried guest and admin with no luck...I've tried many different fixes(modifying registry entries & advanced securities on the win 7 machine) with no luck. Thanks

  Read the article

• Network Computers Not Showing up

  - by Muhnamana

  Alright, 3 machines running, two using Ubuntu 11.10 and one on Mac OS X. On the two Ubuntu machines, both have samba installed and configured on the same workgroup, "HOME". On machine 1, I can see all networked machines. On machine 2, I can only see the Mac OS X machine. It doesn't show the other Ubuntu machine. What am I missing on machine 2 to see all networked computers? Any suggestions are welcome. I'm pretty much stumped.

  Read the article

• Syncing properties across a game server

  - by Vaughan Hilts

  I'm beginning to implement a simple scripting system into my networked server, and I've hit a snag. Before, I've been wrapping my calls into functions on objects that manipulate objects, but lately I've been finding this to be a pain for simple things. For example, if I set 'player.HP = 1'.. this works server-side. But the player side never sees this change unless I explicitly send a packet to inform the client. For many things like map swapping that require more complicated changes, like change X, Y, Map and do this.. I have a function. That's fine. But what about these small properties I want to sync?

  Read the article

• WIFI looses connection with AR9285 - have to disconnect / connect to regain internet?

  - by CodyLoco

  I have a G73JW laptop using Ubuntu 12.04. It has an Atheros AR9285 card. While wifi seems to work fine most of the time, about every hour or two it will loose the connection to the internet. The connection will appear to be connected still to the wireless router, but internet access is gone. Disconnecting and reconnecting to the access point solves the problem, as does disabling and reenabling the adapter via the hardware keyboard shortcut. How might this be solved so the connection is stable and doesn't drop? EDIT: It looks like the network dropping isn't related to DNS as it fails either way: codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com @8.8.8.8 ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com @8.8.8.8 ;; global options: +cmd ;; connection timed out; no servers could be reached codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com ;; global options: +cmd ;; connection timed out; no servers could be reached Again cycling (disabling / enabling) the adapter corrects the issue.

  Read the article

• Adding a 'network' USB printer

  - by AndrewK

  I have a HP Deskjet 1050a printer, hence the 'network' in the title. Its a bog standard USB home printer. I have it attached to my router (has a USB port in it). I have got it connected and working to with Win8 PC and also a MacBook Air. Can't seem to get it to add as a printer to my Xubuntu laptop(s). It doesn't get detected automatically (not an actual network printer) and i've tried multiple options to get it working. It seems to add it but when printing a test page its saying the printer isn't connected. Ping works fine so it can see it, just can't add it as a printer. With Win8 I had to create a port with the IP of the printer (192.168.1.253 in this case), is there an Ubuntu alternative to do this?

  Read the article

• Lost connectivity after configuring multiple network adapters on separate networks

  - by Dave Long

  I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

  Read the article

• How often should multiplayer games communicate with the server?

  - by Bane

  I once heard that Runescape "ticks" every 0.3s, and that seemed like a very long period of time, although Runescape is kind of a slow game. I'm building a more dynamic top-down shooter game, and I'm wandering, how often should I communicate with the server? ASAP, or every 0.1s? How do shooter games usually do it? Both the server and the client are written in Javascript, node.js and socket.io are being used.

  Read the article

• Kubuntu not showing eth0

  - by Laurbert515

  I just installed Kubuntu 12.04.2 and do not have an internet connection. I also cannot access the Desktop and only have the terminal. When I enter xlcock I get Error: Can't open display:. I believe this is because I do not have the correct drivers and need to download them ... using the internet which I can't access. So here's what's going on ... ifconfig gives: lo Link ecap: Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:0 RX bytes:1296 (1.2 KB) TX bytes:1296 (1.2 KB) wlan0 Link encap: Ethernet HWaddr 68:17:29:58:49:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lspci -nnk gives: 07:00.0 Network Controller [0280] Intel Corporation Centrino Wireless-N 2230 [8086:0887] (rev c4) Subsystem: Intel Coporation Centrino Wireless-N 2230 BGN [8086:4062] Kernel driver in use: iwlwifi Kernel modules: iwlwifi 0d:00.0 Ethernet Controller [0200]: Atheros Communications Inc. AR8161 Gigabit Ethernet [1969:1091] (rev 10) Subsystem: Toshiba America Info Systems Device [1179:fa77] I believe this means that it is using the ethernet connection but thinks it is a wireless connection. sudo lshw -class network gives: *-network description: Wireless interface product: Centrino Wireless=N 2230 ... *network UNCLAIMED description: Ethernet controller product: AR8161 Gigabit Ethernet I want to get the internet working so I can fix the GPU driver, etc. but I can't seem to get it working even though I have my ethernet cable plugged in (and I'm sure it is working).

  Read the article

• Windows recv method usage

  - by vandamon taigi

  I'm making a multiplayer game and I have an issue with the recv function ( or the send one , not sure ). Server side code : char* UserName = new char[256]; ZeroMemory(UserName,256); recv(sConnect,UserName,256,0); // works char* Password = new char[256]; ZeroMemory(Password,256); recv(sConnect,Password,256,0); // works users[ ++usercount ] = new Client(UserName,Password,sConnect); if( users[usercount] ->GetLogInSuccesful() ) send(sConnect,"0x0001",6,0); // debugging shows it gets here and sends the data. Client side code : send(server->getsConnect(),User,256,0); // works send(server->getsConnect(),Pass,256,0); // works char* Response = new char[6]; ZeroMemory(Response,6); recv(server->getsConnect(),Response,6,0); // gets stuck here. Any ideea why does it get stuck on that recv ? I also tried by making response [256] or such.

  Read the article

• solve TOR edge node problem by using .onion proxy?

  - by rd.

  I would like to improve the TOR network, where the exit nodes are a vulnerability to concealing traffic. From my understanding, traffic to .onion sites are not decrypted by exit nodes, so therefore - in theory - a .onion site web proxy could be used to further anonymize traffic. Yes/no? perhaps you have insight into the coding and routing behind these concepts to elaborate on why this is a good/not good idea.

  Read the article

• Twitter "Authentication Error" Turpial & Choqok (latest versions)

  - by PineMarten

  I use Turpial a lot, but Turpial isn't connecting at all. I can still connect to Twitter thru the OS app (no issues signing in through Online Accounts) and of course I can still sign in using the browser, but Turpial gives me an "Authentication Error" and Choqok fails to do anything. I've tried changing my password, revoking the Turpial and Ubuntu apps in Twitter and re-enabling them, but then it gives me an "Invalid Credentials" message. I've even removed and installed Turpial multiple times, still nothing. I can't find any information or resources for this type of error from Turpial online. I think it may be something recent after finding this message elsewhere: (article related to "Birdie") It looks promising i'm currently using it atm, since all the other twitter clients no longer work due to the API 1.0 shutdown (posted today) I've never used Choqok before today, so I don't even know if I've set it up properly. It's failing to retrieve or send Tweets it just blank screens, but at least it signs in. I've figured that this isn't an issue with Ubuntu, or Turpial or Choqok, or the router (already replaced it today), so I don't really know what I'm dealing with here. I hope it's not another API issue, Facebook did something similar just a few weeks ago

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >