Search Results

Search found 2795 results on 112 pages for 'nic strong'.

Page 70/112 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• Access points fighting for dominance?

  - by Phillip Oldham

  We have a small office with a large number of wireless devices (a mixture of desktop machines, laptops, and wifi-enabled phones) all working from a single Apple Airport Extreme which extends our wired network. I've added another Airport Extreme for resiliency, since we've been seeing a decrease in performance and (as far as I understand) access points can only handle a small number of clients. I set the new AP to extend the current network so that the clients weren't constantly switching between different wireless networks, however as soon as this AP was configured all the wireless devices started seeing network trouble, flicking on and off. I'm assuming that this is because both APs are reasonably strong, and the client can't decide which to use. What is the best route to follow to resolve this? What I'm aiming for is wireless resiliency; preferably having two APs share the network load, or if this isn't an option then having a primary AP with a "fail-over", should the primary go down for any reason.

  Read the article

• iSCSI performance questions

  - by RyanLambert

  Hi everyone, apologies for the long-winded post in advance... Attempting to troubleshoot some iSCSI sluggishness on a brand new vSphere deployment (still in test). Layout is as such: 3 VSphere hosts, each with 2x 10GB NICs plugged into a pair of Nexus 5020s with a 10gig back-to-back between them. NICs are port-channeled in an active/active redundant fashion (using vPC-mac pinning for those of you familiar with N1KV) Both NICs carry service console, vmotion, iSCSI, and guest traffic. iSCSI is on a single subnet/single VLAN that is not routed through our IP network (strictly layer2) Had this been a 1gig deployment, we probably would have split the iSCSI traffic off onto separate NICs, but the price/port gets rather ridiculous when you start throwing 4+ NICs to a server in a 10gigabit infrastructure, and I'm not really convinced it's necessary. Open to dialogue/tech facts re: this, though. At this point even a single VM guest will boot slowly to iSCSI storage (EMC CX4 on the same Nexus 5020 10gig switches), and restores of VMs from iSCSI take about twice as long as we'd expect them to. Our server folks mentioned that if we split the iSCSI off onto its own NIC, performance seems significantly better. From a network perspective, I've run through the variables I can think of (port configuration errors, MTU problems, congestion etc.) and I'm coming up dry. There really is no other traffic on these hosts other than the very specific test being performed at the time. Important thing to note is that guest traffic works just fine... it seems storage is the only thing affected by whatever gremlin exists. Concluding that we're not 'overutilizing' the network infrastructure since we're doing hardly anything, I'm just looking for some helpful tips/ideas we can use to resolve this... preferably without hurling extra 10gig NICs that are going to sit around 10% utilization while we've got 70+% left on our others.

  Read the article

• IP routing Solaris 9 access the internet from local network

  - by help_me

  I am trying to configure the NICS on the Solaris Sparc server. My problem lies in getting out to the "Internet" from the local network. I have requested the NIC to receive a DHCP server address #ifconfig -interface dhcp start. If anyone could guide me as to what I need to do next. I am not able to ping 4.2.2.2 or access the internet. Much appreciated, thank you #uname -a SunOS dev 5.9 Generic_122300-59 sun4u sparc SUNW,Sun-Fire-V210 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.3 netmask ffffc000 broadcast 10.100.63.255 bge0:2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.22 netmask ffffc000 broadcast 10.100.63.255 bge3: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 12 inet 169.14.60.37 netmask fffffe00 broadcast 169.14.61.255 cat /etc/defaultrouter 10.100.0.254 169.14.60.1 cat /etc/resolv.conf nameserver 169.14.96.73 nameserver 169.10.8.4 netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 169.14.60.37 169.14.60.1 UGH 1 0 169.14.60.0 169.14.60.37 U 1 18 bge3 10.100.0.0 10.100.0.3 U 1 34940 bge0 10.100.0.0 10.100.0.22 U 1 0 bge0:2 224.0.0.0 10.100.0.3 U 1 0 bge0 default 10.100.0.254 UG 1 111 default 169.14.60.1 UG 1 26 127.0.0.1 127.0.0.1 UH 10 59464 lo0 bash-2.05$ sudo ndd -get /dev/ip bge0:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip bge3:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip ip_forwarding 1

  Read the article

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• debian 6 losing a large amount of packets

  - by Sc0rian

  I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc Computer B CANNOT connect as user Y to the server with mstsc! Error that username/password is incorrect. The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. EDIT: I tried: prefixing domain to the username prefixing the server computer name to the username change the password copy/paste the password from notepad to make sure it was correct I find it very strange.... EDIT: The computers are not on the same subnet as the server. The server is at my hosting provider. All computers as all users can reach the web app that is running on the server.

  Read the article

• Is Family Tree Maker 2011 the right upgrade for a FTM 11 user?

  - by bill weaver

  My father has used Family Tree Maker for years, but hasn't upgraded since version 11. It is difficult to tell from reviews at Amazon and other places whether upgrading to FTM 2011 is a good choice. File incompatibilities and upgrade woes sound like customer service is lacking, and i've read reports of it uploading your data to their database but then trying to sell you a download of data. Looking at the ancestry.com site makes me think it's solely about selling add-ons and upgrades. On the other hand, the feature set seems fairly rich and the software has a pretty strong following. I was able to get Gramps working on my system, but that's not going to work for my dad. Any advice on a good upgrade path?

  Read the article

• how to detect device type from connected device to router?

  - by molly

  i have a att router and there is an unknown device connected to my network. i cant seem to kick it off because of how att's router settings are created which is kind of dumb. i am able to see its local ip and mac address. i am on a mac with snow leopard. how can i get more information on the device with the information that i have? i want to see what kind of device it is, i have checked all deviced that are connected to the router and non seem to match the local ip that is connected. i have wpa encryption setup with a strong password.

  Read the article

• Virtualize SBS 2003 - P2V vs migrating to new VM

  - by jlehtinen

  I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

  Read the article

• How to detect device type from device connected to router?

  - by molly

  I have a att router and there is an unknown device connected to my network. I can't seem to kick it off because of how att's router settings are created which is kind of dumb. I am able to see its local ip and mac address. I am on a mac with snow leopard. How can I get more information on the device with the information that I have? I want to see what kind of device it is, I have checked all devices that are connected to the router and none seem to match the local ip that is connected. I have WPA encryption setup with a strong password.

  Read the article

• Window Server 2003 Print spooler

  - by mikenardone

  Hello Everyone in ServerFault, I am new to this website. I have been coming here to fix my own problems. I believe everyone here on this website is great. I could not find this issue anywhere. I am sure that other people had this issue. I have IBM X3850 48GB ram 2 TB of hard drives, four NIC cards. 2 Xeon 1.7 CPU. I am running VMware ESX. I believe that was the paid version if not then it is ESXI. I have 7 Servers on this server. All Window server 2003. On one of the Servers I keep on getting CPU is at 100% . So when I go into task manager and look at the processes that is going on, it is my print spooler. I have 30 different HP laserjet printers and two copiers from HP. I believe it is an driver issue, but I can't figure with one is doing this. Is there any programs for window server 2003 that finds bad print drivers.

  Read the article

• How secure is Microsoft 2007's encryption?

  - by ericl42

  I've read some various articles about Microsoft's encryption, and from what I gather, 2007 is secure using all default options due to it using AES, and 2000 and 2003 can be configured secure by changing the default algorithm to AES. I was wondering if anyone else has read any other articles or know of any specific vulnerabilities involved with how they implement the encryption. I would like to be able to tell users that they can use this to send semi sensitive documents as long as they use AES and a strong password. Thanks for the information.

  Read the article

• Check a list of passwords strength

  - by user144705

  Is there any way to check a list of passwords whether they strong or not? I have a list of passwords, around 2000, and want to check them against this policy Password must contain a minimum of eight (8) characters Password must contain at least one letter Password must contain at least one number Password must contain at least one punctuation character And count how many compliant with that policy before we save them. Is there any tool, script or maybe rules in excel to do this instead of doing it manually? Could you please help me?

  Read the article

• Problem connecting to remote network using demand-dial VPN interface with Windows Server 2003

  - by Mike Forman

  I have a Windows 2003 server (SP2) that I'm trying to set up route traffic from my local network using a VPN My local network has the following components: Broadband router (192.168.0.1) Windows Server with a single NIC running RRAS (192.168.0.2 def. gateway = 192.168.0.1) Client Machine (192.168.0.3 def. gateway = 192.168.0.1) Using a VPN connection, I am trying to access a remote machine (10.0.0.1 for example) I configured RRAS with a demand-dial interface for the VPN and set it to be a persistent connection. As part of that setup, a static route to 10.0.0.0 (255.255.0.0) was created. When at the console of the server, I can ping 10.0.0.1 with no problems I added a route on the client machine using the following command: ROUTE ADD 10.0.0.0 MASK 255.255.0.0 192.168.0.2 If I run tracert 10.0.0.1 from the client, the first hop is to 192.168.0.2 which tells me that route is working. However, I cannot ping 10.0.0.1 from the client machine. What am I missing? Hopefully something simple.

  Read the article

• Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

  - by CITguy

  Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

  Read the article

• C# sends SQL data 4 times less from one box than from another

  - by Bobb

  W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

  Read the article

• Protect Windows VPN from Unauthorized Users

  - by kobaltz

  I have a VPN connection that I use while away from home to remote into my home network. I would use a zero config solution like Hamachi, but need access from my mobile device. Therefore, I have my Windows Home Server acting as the VPN server and will accept incoming connections. Both the username and password are strong. However, I'm worried about brute force attacks against my network. Is there something else that I should do to protect my network from having unauthorized access attempts to my network? I'm familiar with Linux's FAIL2BAN, but wasn't sure if something similar existing for Windows.

  Read the article

• How does pptpd (poptop) or pppd work with eap-tls and mppe-128?

  - by Henk

  To create a VPN I've installed pptpd on an Ubuntu domU (Debian domUs can also be created). MSCHAPv2 isn't a very strong authentication protocol so I'd like to use EAP-TLS. I've set up a FreeRADIUS server and certificates for EAP-TLS before (for use with WPA), and I've also set up a pptp server with mschap-v2 auth, but I can't figure out how to combine the two. Maybe pppd can use EAP-TLS on its own, but I can't find support for it in the Ubuntu package. If I need to patch the package, that's fine, I know how to patch Debian packages (provided the patch applies cleanly). Also, can MPPE still be used when pppd is configured to use EAP? Because it says in the manual several times that MPPE requires MSCHAP. However, other docs like this one: http://www.nikhef.nl/~janjust/ppp/ seem to refute that. The clients are running Mac OS X Leopard and GNU/Linux, there's no need to fix anything for Windows.

  Read the article

• SQL Server 2005 SE SP3 on Windows Server 2008 R2 x64 premature query disconnections

  - by southernpost

  New Dell PowerEdge R910, 4x8 Intel X7560, 192GB RAM, hardware NUMA, local RAID, Broadcom NetExtreme II multiport NIC, unteamed, TCP Offload disabled, RSS disabled, NetDMA disabled, Hyperthreading disabled. SQL Server 2005 SE x64 SP3 on Windows Server 2008 R2 EE x64. No other apps on server. Max Mem = 180GB, Max DOP = 4. Existing Windows Server 2003 R2 EE x64 app server connecting to Dell via firewall using SQL Authenticated logins. Symptoms: Intermittent errors at the app server: A transport-level error has occurred when sending the request to the server. (provider: TCP Provider, error: 0 - An existing connection was forcibly closed by the remote host.) Findings: Running queries from SSMS located on another machine within the same domain as the SQL Server run without error. SQLIO showed good performance. Windows and SQL logs show no related messages. Microsoft reveiwed PssDiag trace and stated that "We are not seeing timeouts from SQL Side. The queries bring run against the database are timing out within 9secs. This is a database connectivity error." "we can also see from the AttnSeq column that we are also not seeing any Attentions from the SQL Side.". Dell has confirmed that we are using the latest Broadcom drivers.

  Read the article

• Transparently decompressing data in archive to allow greater compression later

  - by Vi.

  I have, for example, filesystem image which have some compressed files (with weak compression such as gzip), for example, manpages or archives with the same uncompressed content nearby. How to pre-filter the data to "expand" compressed data to plain form (to re-compress it with strong compression) and then post-filter after decompression to restore original "semi-compressed" image? SHA-1 match is advices but not strictly required (but the resulting image must work, e.g. re-compressed files should not grow too much, be decompressible etc.) Like improving compression ratio by reversing weak compression algorithms. Are there programs for this?

  Read the article

• Recursively apply ACL permissions on Mac OS X (Server)?

  - by mralexgray

  For years I've used the strong-armed-duo of these two suckers... sudo chmod +a "localadmin allow read,write,append,execute,\ delete,readattr,writeattr,readextattr,writeextattr,\ readsecurity,writesecurity,chown" sudo chmod +a "localadmin allow list,search,add_file,add_subdirectory,\ delete_child,readattr,writeattr,readextattr,\ writeextattr,readsecurity,writesecurity,chown" to, for what I figured was a recursive, and all-encompassing, whole-volume-go-ahead for each and every privilege available (for a user, localadmin). Nice when I, localadmin, want to "do something" without a lot of whining about permissions, etc. The beauty is, this method obviates the necessity to change ownership / group membership, or executable bit on anything. But is it recursive? I am beginning to think, it's not. If so, how do I do THAT? And how can one check something like this? Adding this single-user to the ACL doesn't show up in the Finder, so… Alright, cheers.

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• How to setup ping between XP guest from Win8 Host using Hyper-V virtual swtich

  - by rism

  Hyper-V client is installed on a Win8 Pro 64 bit box and a VM running XP has been created within that with an internal virtual swtich. The VM can be booted and accessed and there is a default virtual NIC within it with dynamic IP of 169.254.x.x which i have changed to be a static IP of 192.168.0.12/255.255.255.0 confirmed via ipconfig on the XP guest. The Host has IP of 192.168.0.7/255.255.255.0. Both host and guest have their firewalls disabled for simplicity. I cant ping guest from host nor host from guest. TTL timeout. And with regard to Hyper-V and VMs I dont know what to do next. Both are in same workgroup (as per name) but since they cant ping I guess that means nothing. .... My objective is to share a folder on VM so I can install a 32bit accountancy app that wont run on Win8/7 so if there is a more simplistic way then Im all ears but typically a peer to peer is very simple.

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >