Search Results

Search found 22041 results on 882 pages for 'kill process'.

Page 701/882 | < Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >

• How to restart boot Windows 7 after upgrading to a SSHD on SONY VAIO with recovery discs?

  - by Boris Okun

  The original HDD on my Sony VAIO still works, but has a damaged sector 0 and I was constantly prompted to replace the HDD because of the imminent failure. I created recovery discs as instructed, used a USB external HDD for complete back up (including Windows image back up). After installing the SSHD and using recovery discs to upload Windows and boot, I am getting the Windows welcome screen. Right after that, I'm getting the following message: Windows couldn't complete the installation. To install Windows on this computer, restart the installation. I have tried repeating the process many times all kinds of different ways and I still receive the same message. Also, when I tried to change to partitioning as the other option offered, I get the message: Windows Setup could not configure Windows to run on this computer's hardware. All troubleshooting for hardware and PCU came out solid. I tried to load the image back up from the external drive, but can't load the driver. The computer doesn't see it. Does anyone have a clue or has encountered something similar?

  Read the article

• System State Backup Retention Policies

  - by isoscelestriangle

  I was wondering if there was a general consensus on how long to keep system state backups. I am trying to reevaluate our current backup process, and trying to get a good handle on our current storage requirements. Our current setup involves tapes and sending backups offsite with Barracuda Networks. We have been doing our system state backups with Barracuda now, which does full backups daily, leaving our storage requirements growing quite quickly. My boss is a little too gung-ho with backups and wants our system states saved for quite a while. We currently have 5 days of nightlies, 5 weeklies, 3 monthlies, and so on. I think this is quite overkill for system state backups. My boss wants the ability to go back in time to find when an issue appeared, but I don't think that is practical. Many things change in the course of several months. I also think it would be hard not to notice problems with our DCs and other servers for several months. I would think that a previous week's snapshot and the current week's dailies would suffice. Any advice or reading you can point me to? Thanks!

  Read the article

• MSSQL Timing out, a couple of questions...

  - by user29000

  Hi, About once a week, my MSSQL server is timing out, or rather the machine runs out of RAM. This morning it reached 3.9GB of the available 4, with MSSQL taking up 2.5GB. I'm concerned that i've not configured SQL to release memory as it should, so I ran sp_who2 while the timeouts were occuring to see what process were running. If i could post the CSV datafile i would, however, there were 85 processes in total, mostly related to the Full Text service: FT Gatherer - About 35 of these running under the 'sa' account against the master database with status of either sleeping or background, many were dependant on other processes. Is that normal? MySite database - There were only 5 processes for the one active site/database and all were either sleeping or suspended - but their lastBatch dates were set to 1/12/2020. Is that normal? The datbase is only about 20mb in size the traffic levels are very low, so i'm thinking of maybe limiting the amount of RAM SQL has access to (from unlimted to maybe 2GB). Any thoughts / advise would be appreciated. Mny thanks Ben

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• TEMP environment variable occasionally set incorrectly

  - by Roger Lipscombe

  Occasionally, I find my TEMP and TMP environment variables set to C:\Windows\TEMP. They should be set to %USERPROFILE%\AppData\Local\Temp, and are configured correctly in System Properties. This manifests itself as error messages like the following: ---> System.InvalidOperationException: Unable to generate a temporary class (result=1). error CS2001: Source file 'C:\Windows\TEMP\gb_pz65v.0.cs' could not be found error CS2008: No inputs specified ...which occurs in various .NET applications (in particular Visual Studio 2010 or SQL Server Management Studio). Alternatively, SQL Server Management Studio will report: Value cannot be null. Parameter name: viewInfo (Microsoft.SqlServer.Management.SqlStudio.Explorer) If I run PowerShell elevated, then $env:TEMP is set correctly. If I run PowerShell non-elevated, then it's not. I believe that it should be set correctly in both cases. If not, it's the wrong way round. The same is true for CMD.EXE. Rebooting fixes it, temporarily, until something breaks it again. Presumably something loaded into Explorer.exe is messing with its environment variables, but what? The values in the registry are correct, even while this is happening: HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Environment has TEMP = %SYSTEMROOT%\Temp HKCU\Environment has TEMP = %USERPROFILE%\AppData\Local\Temp By setting a breakpoint on shell32!RegenerateUserEnvironment, I'm able to trap it when it happens, but I still don't know why explorer.exe is reading the wrong environment variables. I can reproduce it consistently by broadcasting a WM_SETTINGCHANGE message (I wrote a one-line C++ program to do this). Watching the activity in Process Monitor shows that explorer.exe doesn't even look at HKCU\Environment. What is going on?

  Read the article

• Three server processes consume no more than 50% of Dual Core CPU

  - by thor

  I have three processes running on Intel Core 2 Duo CPU. From watching output of 'top' and graphs of CPU load (drawn by MRTG, data collection via SNMP) I can see that CPU load is never more than 50%, and, most of the day, when those processes are busy CPU load has a ceiling at 50 %. I mean, CPU load grows up to 50% in the morning and stays there until late evening. My first thought was that only one core was used at 100% thus giving 50% of both CPUs. But, as there are three processes running and from 'top' I see that both cores are being loaded, so this is not the case. schedtool shows that CPU affinity for those three processes is at default, 0x03, allowing them to use both cores. If I force one process to one core (schedtool -a 0x01), and two others to second (schedtool -a 0x02), cumulative usage grows beyond 50%. Why three processes seem to consume only 50% of two cores? Why forcing them to different CPUs allows usage to grow higher? Any hints? P.S. Processes in question are Counter-Strike servers.

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

  - by CityView

  On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

  Read the article

• Disk usage on IIS, PHP5, performance problems.

  - by Jacob84

  Hi everybody, I'm quite worried with a performance problem that I'm facing in one of our production servers. I'm working for a hosting company, so you can imagine how heterogeneous the applications runnning here are. All started with a call of a client complaining about the speed loading a Joomla. The setup is IIS6 (Windows 2003) with PHP5 and FAST CGI wich normally works pretty well. I've tested the loading time and indeed, he was right. 7 or 8 seconds to load, when usually this can be accomplished in 2. Seeing this results, I started to check first CPU and RAM. Everithing normal, 2GB of RAM free, 3%-8% of CPU activity. That's what I call a relaxed server ;). Unfortunately, digging a little deeper I've found the 'PhysicalDisk' counters quite high (above 10), specially the read queues. I've used Process Explorer to see wich of those processes has the higher deltas, but everything seemed normal. As the problem is specially related to PHP pages, I've checked specific IIS counters, as Actual connections, Number of CGI requeriments and Number of ISAPI requeriments. CGI -> 3 to 7 ISAPI -> 5 to 9 Connections-> 90 to 120 (wich appears at the top of the graph) More than a solution (I know this is hard to find), I would like to know if you have an specifical methodology to face this kind of problems. Thanks a lot, as always.

  Read the article

• Port forwarding with multiple IP's

  - by Jon

  I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

  Read the article

• Intermittent Trouble Entering Hibernate on WinXP

  - by kquinn

  My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

  Read the article

• How can I move linked Word/Excel files without breaking the links under Windows 7?

  - by DOUG NEEDHAM

  I currently operate under Windows XP and have multiple links between my Word and Excel files. I have to upgrade to Windows 7. When the .doc and .xls files are converted to .docm and .xlsm, respectively, the links no longer work. The Word document is still attempting to point back to the old .xls file rather than the new file. Also, creating new links between Word and Excel within Office 2010 doesn't seem to work. I create the new link, switch it from "Auto" to "Manual" and everything works fine. But when I copy the files to another folder, the Word document is still trying to link to the file in the previous folder rather than the new folder. This always worked in Windows XP. I've been using linked Word/Excel documents for 10+ years and have never really had a problem. I'm very careful to maintain Word and Excel filenames when moving the files to a new folder. The process has always been to 1.) move the files, 2.) update the links, 3.) rename the files, and 4.) update the links again. It's my understanding that under Windows XP, links between Word and Excel are relative. But under Windows 7 (and Office 2010?), those same links become fixed.

  Read the article

• Weird problem with Visual C++ 2010 Express

  - by Robert Vella

  This has happened before on my Vista Premium installation, and now it's happening on my Windows 7 Home Premium installation. Basically everytime I install Visual Studio Express 2010, it works fine for a random amount of time but then suddenly starts to hide from my sight -- that's the best way I can explain it. VS does not crash, and from what I can tell it does not freeze either; It continues to work, I can even "minimize" and "maximize" it; I simply cannot see it nor can I interact with it any meaningful way. Also: After the "crash" there are no logs in: Root\Program Files (x86)\Microsoft Visual Studio 10.0\Microsoft Visual C++ 2010 Express - ENU. Nor any other files created at the time of the crash. There are no traces in the event viewer. The program seems to be functioning perfectly in the process manager. If I reinstall Visual C++, it works normally for a seemingly random period of time before going cookoo again. I am stumped. This has never happened to me before, with any other program. And yet I doubt it really is a problem with Visual C++; More like something general that seems to have picked on it for some reason. Still, after a clean install with a new OS, I'm kinda thinking there's something wrong here. Any help would be appreciated, altough I suspect that the answer to this question will make me feel embarassed. P.S. Not sure if it helps, but I think around the same time I started having problems (On both installations) with windows turning off the display when I leave the computer, and then seemingly crashing when it turns it on again -- in fact when I interact with it it seems to be responding to my commands without actually display anything.

  Read the article

• Windows Media Center showing Jerky Video on PC

  - by Kris Erickson

  I had to repave my Windows 7 x64 box last week due to a hard drive crash, and for a while everything was running perfectly but now all videos in Windows Media Center are jerky (the sound is fine, they just seem to skip a ton of frames all the time). This is on the local machine, but the same thing happens when I try to stream to my Xbox. The videos all show fine in VLC and Windows Media Player (however exhibit the same problem in Quicktime). I guess I must have installed something recently (in the process of getting all the apps I usually have running on my PC) that caused this but for the life of me I can't figure it out. I have updated to the latest video driver (and then rolled back to the standard Windows 7 driver), I have rolled back all the other drivers that I have installed (I believe). I have uninstalled all the codec packs (I also run TVersity, so I have the TVersity codec pack installed), and I uninstalled TVersity. Nothing seems to help. I have uninstalled windows media center, and reinstalled it from the Programs and Features. I have basically ran out of things to try to fix this, and am almost thinking about reinstalling Windows again. Any suggestions? Edit Specs on the PC (which I figured was unimportant since everything used to work perfectly): Intel Core 2 CPU 6600 @ 2.4 Ghz Nvidia GTS 8800 Built in realtek-audio soundcard 4GB Ram Codecs which are failing: All that I have tried, but at least Xvid, Mpgv (mpeg2 video from a camera), and Wmv (only kinds that I have ready access to).

  Read the article

• ssh-add insists on passphrase

  - by Sam Walton

  I have a new ssh key problem. I have successfully used them for years with Heroku, Git and other servers so I can login without having to issue a passphrase. A few weeks ago, I was unable to push a git repository on my machine to my Heroku and it responded with Permission denied (publickey). Hmm. Everything else but this Heroku function still works. So I ssh-keygen -t rsa -C "newHeroku" with no passphrase (hit return so it would be empty). So I enter: sudo chmod 600 ~/.ssh/newHeroku* Then: ssh-add ~/.ssh/newHeroku.pub Returning return for the passphrase asked it exits without error. The next step is to: ssh-add /Users/sam/.ssh/newHeroku.pub To verify that it's "live" I enter: ssh-add -l To which the output is still The agent has no identities. Okay, to eliminate variables, I repeat the key generation process but entering in a passphrase for a new key. I ssh-add the new key and get the "Enter passphrase" as expected. Now this is why I'm posting here and not on a Heroku blog because ssh-add fails because the passphrase I used keeps getting rejected. It appears, even though I have no problem with my keys elsewhere, that something is wrong with passphrase because even though I get no errors, I get errors when on the one that expects a passphrase. One question, should I expect the Passphrase request for ssh-add when I have not generated a passphrase? It's been suggested that this is a clue and I offer it. Or maybe I have a poor understanding of what ssh-add is doing. Wouldn't be the first time I asked a stupid Q. Also, I'm on Lion and have updated no system updates in the few weeks of this period except application updates.

  Read the article

• Daisychain external USB drive to WD My Book World Edition (Blue rings)

  - by d03boy

  I recently bought a new My Book Essential 1TB (WDBACW0010HBK-NESN) to daisychain to my older My Book World Edition 500GB (blue rings) with one of the version 01.xx.xx firmwares. At first when I connected the USB drive to the MBWE, it showed up in the System Summary section of the administration page without any issue. I was able to set up a new share on the new drive. The administration website moved very, very slow though. The administration pages became nearly unresponsive during this setup process. Once the share was set up I could access the new share but again, it was very slow, now through Windows Explorer. I looked around the internet and it seems that this is caused by the USB drive being formatted with NTFS. I tried reformatting it (again, as NTFS) just to double check and the same problem occurred. I then tried FAT32 but realized it would only support files of approximately 2GB and that is not acceptable for me. I decided to try a firmware upgrade on the MBWE to version 02.00.19. The firmware upgrade completed successfully but now the MBWE does not display the USB drive in the System Summary like it did with the earlier firmware version. The USB drive works perfectly fine when connected directly to my computer. Is there a way to solve this issue?

  Read the article

• Processes spawned by taskset not respecting environment variables

  - by jonesy16

  I've run into an issue where an intel compiler generated program that I'm running with taskset has been putting its temporary files into the working directory instead of /tmp (defined by environment variable TMPDIR). If run by itself, it works correctly. If run with taskset (e.g. taskset -c 0 <program> Then it seems to completely ignore the TMPDIR environment variable. I then verified this by writing a quick bash script as follows: contents of test.sh: #!/bin/bash echo $TMPDIR When run by itself: $ export TMPDIR=/tmp $ test.sh /tmp When run through taskset: $ export TMPDIR=/tmp $ taskset -c 1 test.sh "" Another test. If I export the TMPDIR variable inside of my script and then use taskset to spawn a new process, it doesn't know about that variable: #!/bin/bash export TMPDIR=/tmp taskset -c 1 sh -c export When run, the list of exported variables does not include TMPDIR. It works correctly with any other exported environment variable. If i diff the output of: export and taskset -c 1 bash -c export Then I see that there are 4 changes. The taskset spawned export doesn't have LD_LIBRARY_PATH, NLSPATH (intel compiler variable), SHLVL is 3 instead of 1, and TMPDIR is missing. Can anyone tell me why?

  Read the article

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• Permissions in OS X for iTunes library with multiple users

  - by John

  I currently have a lot of music on an external drive and my iTunes set up from there. However, periodically, when the external drive isn't connected, iTunes will default back to the library location of my home directory user path. I don't want to mess with an external drive, as my Mac's HD is large enough to house the music collection. However, I have 4 family members – all with their own logins – using this same gob of music. I don't want four copies of the library, only one with all libraries referencing it. So, what I want to do is: Move all music files to a shared directory at /Macintosh HD/users/music. I created this directory and adjusted permissions, so all four users can read and write to this directory. Get all four accounts to reference this library instead of the external or local home locations I am hoping I can just check the box to keep library organized in my account, which is the admin and let iTunes move it all. Then delete current libraries for each account and re-add from the new shared location. Will the iTunes organization process cause permissions issues either by setting permissions to all the files access to my account only or write permissions or any other 'gotcha'? I am having a hard time coming up with a smooth solution that won't break everything and cause me to have mega duplicates or access issues. I would prefer not to do any XML library file editing if possible. Am I dreaming?

  Read the article

• Linux virtualization choices with graphic acceleration / video card support

  - by Urbn

  I am in the process of building a new desktop machine for work and fun. I am looking to run a undecided flavor of Linux (guessing Ubuntu) as my primary OS and several Windows installs with a Windows 7 install for .net development and gaming as virtualized environments. From my previous experiences with virtualization software in Linux I was never able to find an application that offered descent video card support / graphic acceleration etc. to be capable of playing any games within one of the virtualized environments. And since I will be investing quite a bit of money into this system for gaming I would naturally want to find the best option available to achieve this setup. So Onto my question: Is there any virtualization software available for Linux that has full video card support, graphic acceleration and capable of taking advantage of everything the video cards have to offer within the virtualized environments? Or am I stuck with running Windows 7 as my primary OS and using virtualization for Linux and the other OS's? Also I have no preference on open/closed source and price range would be up to $175.00 to support at least 3 virtualized environments.

  Read the article

• Hard Drive that was used before not detected or accessible in Windows 7

  - by Anders

  Hello SU: My PC crashed for some unknown reason, and I am still working on what caused that. However, I pulled my main (windows) drive from my computer and hooked it up to my roommate's machine and was able to pull the data I needed off of it (i.e. the drive is good). I hook up his drives as they were, I had to turn off his machine and unplug his secondary drive to hook mine up, boot his machine and there is no second drive available in windows explorer. I opened Device Manager to see if for some reason it's drive letter got un-assigned, but there is nothing listed in there except his primary hard drive, his optical drive and one other optical drive which I believe is the virtual drive Daemon Tools made. The drive shows up in the BIOS, however after I restarted his machine again it sits on the "Entering setup....." screen at the load window. The only thing I can think of is that may have messed with stuff is I used this tutorial to create a bootable XP install on a USB drive to install XP on my machine (I am 99% certain that the optical drive in my PC is broken) and maybe it used the other hard drive's letter for the USB drive for some reason, which doesn't make much sense since it was recognized it as a different drive letter before I started the process. It is possible that it used the secondary hard drive's letter for it's work, but once again I am uncertain. Where should I go from here? He his bound to wake up within the next several hours and will probably flip a lid if I cannot get some sort of handle on this. Any and all help is greatly appreciated. PS: Anyone who helps me get this situated has a beer or two on me, as long as you are in the greater metro Detroit area, or don't mind traveling a bit!

  Read the article

< Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >