Search Results

Search found 20021 results on 801 pages for 'software engeneering learner'.

Page 702/801 | < Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Erratic WiFi 2.4 GHz channel spikes, what gives?

  - by Francis W. Usher

  Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Production deployment to EC2 with minimal downtime

  - by jensendarren

  I have a simple web application deployed on a large instance with EC2. I now want to deploy the latest code to this server but I want to do this in a way which minimizes downtime and is a smooth as possible for the end user. Here is my plan: Fire up another large instance Install all the software layers on that instance Restore and attach an EBS drive to the instance Deploy our latest production ready code on the new instance Run all tests (including manual testing of the application) (If tests pass) Put a "Site Under Maintenance" notice on the live site. Backup the EBS instance on the live site Detach the EBS instance from the new server and replace with the latest backup Use ec2-associate-address to move the IP address to the new instance Sit back and wait for traffic to start flowing though the new instance Terminate the old instance Does this seem like a good strategy? Are there any tutorials or books that might cover this topic? I have already read Cloud Application Architectures by George Reese, which is an excellent book, but does not cover deployment. Additionally, I know that there are tools that can help with this like RightScale or enStratus which I will use when I start using more than one instance.

  Read the article

• Can Octopussy use messages other than syslog style?

  - by Lee Lowder

  I am currently exploring different options for a centralized log server. We use both Linux (Ubuntu 10.04 / 12.04, LTS for both) and Windows, though for this specific issue only Linux is relevant. I like the interface that octopussy has and it's feature list, but I am hesitant due to a few things. One of the biggest concerns I have is that it seems to be syslog only. The end goal is to have a centralized place for our devs and admins to be able to search through the logs generated by Apache, Tomcat and 70+ web apps spread out among a cluster, for both our prod and test environments. While I did see that octopussy has support for plugins, I haven't been able to find any sort of plugin repo or in depth guides as to what can be done with them. Does anyone know if plugins can be used to allow octopussy to non-syslog messages? Specifically log4j type log messages that may include multi-line stack traces and such. Also, is there a user community for this software, such as a mailing list or forum? I've been unable to locate any so far. Thank you.

  Read the article

• Create a PDF that defaults to flip on short edge when printed double-sided

  - by user568458

  We're creating a 2-page PDF brochure with a target audience who will print it on their regular office or home printers. If it is printed on a double-sided printer (common in offices), it'll come out correctly if set manually by the user to "Flip on short edge", but will come out with the second page upside down if default settings are used (flip on long edge). Our target audience aren't very tech-literate, and we've found that even within our own office network there is variation in the location of the 'Flip on short edge' setting - so it isn't realistic to give everyone who downloads the PDF instructions on how to change this setting or to expect everyone to find out how to change the setting off their own backs. So, when creating a PDF (ideally using Adobe InDesign or Acrobat, but if other software or hacking is needed that's fine...), is there a way to configure the PDF file itself so that when printed double-sided with default settings, it flips on the short edge? If possible, it'll be useful supplementary info to know how reliable any such methods are across different PDF readers (e.g. Adobe Reader, Acrobat, Mac Preview, inbuilt browser readers (e.g. chrome), FoxIt, etc). If questions about content creation like this aren't a great fit here, feel free to migrate it to the graphic design stackexchange site - this question seems to fall half way between the two sites

  Read the article

• Encrypted folders and files stay encrypted when copied

  - by user66126

  Hi all, I just tried out Windows 7 feature to encrypt a folder. I found that when I access the encrypted folder from another computer (the parent folder of the encrypted folder is shared) I can see the files there but I could not open it (which is good). But when I copy the file to another folder outside the encrypted folder (regardless it is on the same remote computer or to the computer from where I am accessing the files) then I can open the file without any problem. This might be how it works ... but that's not what I need. My question is: Can I encrypt a folder (and all files inside), access those files (create, edit) seamlessly while I am logged in normally to the computer ... but make the files stays encrypted when they were copied to another directory outside the encrypted folder? Regardless they were copied to the same computer or another computer or uploaded to a remote server. If this is not a feature that Windows natively support, is there third party software that does that? Thank you.

  Read the article

• RAID 6 that can read with least 1000 Mbit/s?

  - by Diblo Dk

  I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

  Read the article

• How to record tv to network share with Windows Media Center?

  - by Peterdk

  Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

  Read the article

• Recover data from Dynamic Disk (MBR) bigger than 2TB

  - by Helder

  Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

  Read the article

• All of the NTFS hard links damaged, where are hardlinks stored and how to recover them?

  - by String Xu

  This is Windows 7 x64 sp1 on a NTFS file system. All hardlinks within C:\Windows\System32 folder disappear, and the Windows can't boot, because even the osloader, C:\Windows\System32\boot\Winload.exe also disappeared. Nevertheless, the original files are still located in the corresponding C:\Windows\winsxs folders. After booting into the Recovery Environment, and copied one Winload.exe (x64) from other folder, Windows gave an error pointing out that "ntoskrnl.exe is corrupted or missing...its file digital signature cannot be verified" In trying to boot in Safe Mode, the message above was shown after a screen prompting "Loaded \Windows\system32\config\system" Because at this early booting stage, smss.exe was still not loaded, so there is not any dumping and logs. Based on my study, ntoskrnl.exe depends on the following files: C:\windows\system32\PSHED.DLL C:\Windows\System32\hal.dll C:\Windows\System32\kdcom.dll C:\Windows\System32\clfs.sys C:\Windows\System32\ci.dll All those files above are copied from their corresponding folders and verified their md5 with a well-operating Windows 7 x64 SP1. But the booting error is still the same: "ntoskrnl.exe is corrupted or missing..." Background: 1. Before the reboot, there was an windows update going on. Then something unknown happen, almost all processes were broken to run, including the windows task manager, taskmgr.exe. After mount the hard disk to other computer, it seems that all hardlinks within C:\Windows\System32 folder were gone. I tried several data recovery software, but they are not be able to find those disappeared NTFS hard links. So the question is: Where are information about those hard links stored? And how to recover them? Are they depend on some windows service or stored in the registry?

  Read the article

• How can visiting a webpage infect your computer?

  - by Cybis

  My mother's computer recently became infected with some sort of rootkit. It began when she received an email from a close friend asking her to check out some sort of webpage. I never saw it, but my mother said it was just a blog of some sort, nothing interesting. A few days later, my mother signed in on the PayPal homepage. PayPal gave some sort of security notice which stated that to prevent fraud, they needed some additional personal information. Among some of the more normal information (name, address, etc.), they asked for her SSN and bank PIN! She refused to submit that information and complained to PayPal that they shouldn't ask for it. PayPal said they would never ask for such information and that it wasn't their webpage. There was no such "security notice" when she logged in from a different computer, only from hers. It wasn't a phishing attempt or redirection of some sort, IE clearly showed an SSL connection to https://www.paypal.com/ She remembered that strange email and asked her friend about it - the friend never sent it! Obviously, something on her computer was intercepting the PayPal homepage and that email was the only other strange thing to happen recently. She entrusted me to fix everything. I nuked the computer from orbit since it was the only way to be sure (i.e., reformatted her hard drive and did a clean install). That seemed to work fine. But that got me wondering... my mother didn't download and run anything. There were no weird ActiveX controls running (she's not computer illiterate and knows not to install them), and she only uses webmail (i.e., no Outlook vulnerability). When I think webpages, I think content presentation - JavaScript, HTML, and maybe some Flash. How could that possibly install and execute arbitrary software on your computer? It seems kinda weird/stupid that such vulnerabilities exist.

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• Password-less login into localhost

  - by Brad

  I am trying to setup password-less login into my localhost because it's required for a tutorial. I went through the normal steps of generating an rsa key and appending the public key to authorized_keys but I am still prompted for a password. I've also enabled RSAAuthentication and PubKeyAuthentication in /etc/ssh_config. Following other suggestions I've seen, I tried: chmod go-w ~/ chmod 700 ~/.ssh chmod 600 ~/.ssh/authorized_keys But the problem persists. Here is the output from ssh -v localhost: (tutorial)bnels21-2:tutorial bnels21$ ssh -v localhost OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /Users/bnels21/.ssh/id_rsa type 1 debug1: identity file /Users/bnels21/.ssh/id_rsa-cert type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 1c:31:0e:56:93:45:dc:f0:77:6c:bd:90:27:3b:c6:43 debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /Users/bnels21/.ssh/known_hosts:11 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/bnels21/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering RSA public key: id_rsa3 debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /Users/bnels21/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Any suggestions? I'm running OSX 10.8.

  Read the article

• Wireless card overheating?

  - by Sidney

  Ok, so I've had my laptop for several years (I wanna say 4, but possibly more), it's a Toshiba Satellite. I'm running Linux mint 15, and am having a strange new issue, after several hours of running my wireless stops. It can SEE wireless networks, but refuses to connect to any of them. (On a sidenote, connecting to a router with a cable at this point works fine) The fact that it can SEE the networks make me think the card is in good condition, and it's software related The fact that it works for several hours before booting me makes me think perhaps the transmitter is getting too hot. I don't use my laptop in dusty environments, and keep it on an elevated surface (alternatively, I actively try not to let it sit on soft surfaces where the vents get covered). I spray out the cpu fan about once a year with compressed air about once a year, so I really don't think the insides should be too dirty. Finally, unfortunately, sensors only gives me CPU temps, but they run about 40-50 degrees C, which from my understanding is perfectly normal for an I3. Does anyone have any suggestions on what I can do to determine the root cause of this?

  Read the article

• Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

  - by Boris

  I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• How to increase the speed between two external hard drives on my laptop?

  - by Roman

  Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

  Read the article

• rpmbuild gives seg fault

  - by Deepti Jain

  I am trying to build an rpm using the rpmbuild tool. I have source code which build binaries around 30 GB. This software for which I am making the rpm has dozens of executables. When I copy only the binaries of a single executable (Eg. init) my rpm builds successfully. But when I dump the entire build to the rpm, rpmbuild does everything but gives a seg fault in the end. Here is my spec file: # This is a sample spec file for wget %define _topdir /root/mywget %define name source %define release 1 %define version 1.12 %define _builddir /root/mywget/BUILD/glenlivet %define _buildrootdir /root/mywget/BUILDROOT %define _buildroot /root/mywget/BUILDROOT %define _sourcedir /root/mywget/SOURCES BuildRoot: %{_buildroot} Summary: GNU source License: GPL Name: %{name} Version: %{version} Release: %{release} Source: %{name}-%{version}.tar.gz Prefix: /usr Group: Development/Tools %description The GNU sample program downloads files from the Internet using the command-line. %prep %setup -q -n glenlivet %build cd %{_builddir} make all %install rm -rf %{_buildrootdir} mkdir -p %{_buildrootdir}/bin cp -p -r %{_builddir}/build/obj-x64/* %{_buildrootdir}/bin/ %files %defattr(-,root,root) /bin/* If I only copy some of the binaries (let say one utility and its dependent binaries) it works fine. But when I try to copy the entire build, I get a seg fault. I get the seg fault after rpmbuild has executed these sections: %prep %build %install rpmbuild also processes my source file. Processing files: source-1.12-1 Finding Provides: Finding Requires: Finding Supplements: Provides:...... Requires:...... Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Segmentation fault Any clue what wrong is going on or where does rpmbuild fails? Thanks in advance

  Read the article

• Creating security permissions for a non-domain-member user in Windows Server 2008

  - by Overhed

  Hello everyone, I apologize in advance for incorrect use of terminology, as I'm not an IT person by trade. I'm doing some remote work via a VPN for a client and I need to add some DCOM Service security permissions for my remote user. Even though I'm on the VPN, the request for access to the DCOM service is using my PCs native user (and since I'm running Vista Home Premium it looks something like: PC-NAME\Username). The request for access comes back with access denied and I can not add this user to the security permissions as it "is not from a domain listed in the Select Location dialog box, and is therefore not valid". I'm pretty stuck and have no clue what kind of steps I need to do here. Any help would be appreciated, thanks in advance. EDIT: I have no control over what credentials are being passed in to the server by my computer. This scenario is occurring in an installation wizard that has a section which requests you point it to the machine running the "server" version of the software I'm installing (it then tries to invoke the relevant COM service, but my user does not have "Remove Activation Permissions" on that service, so I get request denied).

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• How should a small company administer their web server?

  - by John Isaacks

  We currently have our website hosted by a small company that is actually a reseller for Rackspace. They act as our server administrators. They configured the servers, handle the backups, if there is a problem, we call them and they fix it. We are growing and want to move away from our shared server to either a cloud or dedicated server. I am thinking cloud myself but I am open to either. The current company doesn't seem to want to offer us anything more than a shared hosting plan. I looked into cloud solutions at vps.net, with them I would have to be the server administrator myself. I am the website programmer but administering the server is outside my comfort zone. vps.net does have a $99/month plan for Pro-Active Managed Support but I am not sure if this is the equivalent on a server admin that is there when you need them. We could hire someone in house, but I think that would be overkill for our needs. I am not exactly sure what we need, I do know we need as close to 100% uptime as we possible can. and we need the ability to add/remove/change the server configuration/software/etc. when needed (though changes shouldn't be very often once everything is setup right). Can someone point me in the right direction? What do other companies do?

  Read the article

• How to organise storage for media content such as video and music?

  - by thor

  Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

  Read the article

< Previous Page | 698 699 700 701 702 703 704 705 706 707 708 709  | Next Page >