Search Results

Search found 20761 results on 831 pages for 'chef client'.

Page 710/831 | < Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >

  • Can't ssh from CentOS 6.5 to SUSE LINUX 10.1

    - by Pavel Tankov
    We have a quite old installation of SUSE LINUX 10.1 (i586) in the office. The problem shortly: I can successfully ssh to it from machines in the same LAN (192.168.1.0) and not from others (that are in 10.23.0.0). The SuSE has SSH server openssh-4.2p1-18.12. I have ruled out the firewall and hosts.allow and hosts.deny files. When my ssh login attempt fails, here is what the logs say: on the client: $ ssh -vvv 192.168.1.5 OpenSSH_5.3p1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.1.5 [192.168.1.5] port 22. debug1: Connection established. debug1: identity file /home/nbuild/.ssh/identity type -1 debug1: identity file /home/nbuild/.ssh/identity-cert type -1 debug1: identity file /home/nbuild/.ssh/id_rsa type -1 debug1: identity file /home/nbuild/.ssh/id_rsa-cert type -1 debug1: identity file /home/nbuild/.ssh/id_dsa type -1 debug1: identity file /home/nbuild/.ssh/id_dsa-cert type -1 on the server: Aug 21 16:34:25 serverhost sshd[20736]: debug3: fd 4 is not O_NONBLOCK Aug 21 16:34:25 serverhost sshd[20736]: debug1: Forked child 20739. Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: entering fd = 7 config len 403 Aug 21 16:34:25 serverhost sshd[20736]: debug3: ssh_msg_send: type 0 Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: done Aug 21 16:34:25 serverhost sshd[20739]: debug1: rexec start in 4 out 4 newsock 4 pipe 6 sock 7 Aug 21 16:34:25 serverhost sshd[20739]: debug1: inetd sockets after dupping: 3, 3 Aug 21 16:34:25 serverhost sshd[20739]: debug3: Normalising mapped IPv4 in IPv6 address Aug 21 16:34:25 serverhost sshd[20739]: Connection from 10.23.1.11 port 44340 The above log on the server is when I enable DEBUG3 log level. However, with the default log level (INFO), the only thing the server logs is this: Aug 21 16:38:32 serverhost sshd[20749]: Did not receive identification string from 10.23.1.11 Any hints? I feel I've tried everything already.

    Read the article

  • iptables drops some packets on port 80 and i don't know the cause.

    - by Janning
    Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

    Read the article

  • Help configuring Mercury mail or similiar with XAMPP to send e-mail outside of localhost

    - by user291040
    I'm building a PHP/MySQL driven website for my department at work (installed via XAMPP). I need to be able to send mail to outside e-mail addresses (e.g., Yahoo, Hotmail, etc.) using the PHP mail() function. As I see it I have to solutions: Configure the SMTP directive in php.ini to the server running at my work. Configure/run a mail server that can send e-mails outside of localhost (I'm trying Mercury because it comes installed with XAMPP). Here are problems I've come up against: I took a guess at our SMTP server name, and when calling PHP mail(), I get the error SMTP server response: 530 5.7.1 Client was not authenticated I can't be sure, however, the SMTP name is correct (I can't get help from our IT guys because of politics). I have tried to use mercury mail. Mercury seems to be picking up the request, but it doesn't want to forward the e-mail to the outside. I keep getting a Temporary error 240 (temporary MX resolution error). I've searched high and low but still can't find a definitive answer on how to send e-mails outside of localhost. Any help is greatly appreciated.

    Read the article

  • Have to run auto-negotiate between clients and switch - "old" switch works fine - "new" switch results in "port flapping"?

    - by ConfusedAboutSwitching
    I need some help understanding a problem we're having at work: We run Altiris/Deployment Solution and have to use auto-negotiate between client systems and our switches (Altiris apparently requires this for imaging, PXE boot and other functions). We have several areas with old wiring (Cat 3 & Cat 5) that have old 10/100 Cisco switches in them - and we can set these systems up to "auto/auto" (auto-negotiate on both the NIC and the switch port), and everything has been working fine. But - our networking crew changed out a couple of old switches for 10/100/1000 Cisco switches, and now - they are claiming that "auto/auto" won't work because the switches can't auto-negotiate the way the old 10/100 switches did - and that if we try to set the new gig switches to auto-negotiate, the switch port starts "port flapping", and shuts the port down. But - if we put the old switch back in - they work using "auto/auto" just fine - no port flapping. The networking crew is telling me that the problem is that we're putting "new switches" on "old wire", and that the old cabling can't/won't support the auto-negotiation with these new switches....??? There's something about this that doesn't make sense to me - can someone explain this to me? Or is our networking crew just doing something wrong in the configuration of these new switches? While will the old switches work "auto/auto", but the new switches won't?? HELP!!....and Thanks!! M

    Read the article

  • SBS DC DNS entries going missing?

    - by Chris W
    I've been looking at a problem on a friends SBS (2003) server where the client PC's aren't able to connect to the server with a variety of errors reported. Checking the server itself the only indicator of an issue is an error 5782: Dynamic registration or deregistration of one or more DNS records failed with the following error: No DNS servers configured for the local system. Running a dcdiag reports that there are no DNS records registered for the DC so I fixed the problem by doing a netdiag /fix after which the dcdiag comes back clean and clients are ok again. It happened a few weeks ago as well and the same fix solved it. What are the possible causes of the DC DNS entries going missing? Is this a config option that needs tweaking or could it be solved by something simple like scheduling the SBS server to re-boot periodically? The only change they can think of that was made near to the time of the first instance of this problem occurring is that RRAS was started up to allow for a VPN connection from a home user. NB - The server is setup with a pair of NICs in a team so the server has a single virtual NIC providing both LAN/WAN connections to it. An external hardware firewall is in use rather than the windows firewall.

    Read the article

  • Noisily rendered text in Firefox

    - by Notinlist
    It came to me in a week or so that certain pages (Facebook, StrackOverflow, some news sites) have text rendering errors in Firefox. As a workaround if I refresh the page, or simply select and deselect the buggy text, the unpleasant effect disappears. I don't have this effect in Internet Explorer or in any of my desktop applications. Windows 7 Pro 64bit (fresh) Firefox 19.0.2 (fresh) Ati Radeon HD 4600 Series (fresh drivers) Thanks for the help in advance! Update 1/2 I have only three addons: Forecastfox, Hungarian spell checking dictionary and Quick locale switcher. The latter two are installed after the effect appeared. I disabled the first individually and did not helped. But if I start my firefox with disabled addons I cannot reproduce the error. As far as I know this mode does not mean disabled plugins, which I do have (Adobe Acrobat, Citrix ICA Client, Google Earth plugin, Google update, Java Deployment Toolkit 6, MS Office 2010, MS Windows Media Player Firefox, Shockwave Flash, Silverlight, VLC Web). Update 2/2 If I disable all plugins and extensions I still have the problem. If I start Firefox with disabled addons then I cannot reproduce the problem.

    Read the article

  • can't register a soft phone to asterisk11

    - by Tom
    I have a VM (on oracle vbox) running Fedora17. I've installed asterisk 11 on it from sources. I've followed the wiki for installation (https://wiki.asterisk.org/wiki/display/AST/Creating+SIP+Accounts) to the letter. The ip on the VM machine running fedora is 192.168.1.7 and I can ping it from the host machine (Ubuntu 12.04), which is at 192.168.1.2 I've tried registering with ekiga with the following settings: user: [email protected]. Password: verysecretpassword registar: 192.168.1.7 but I'm getting an error "transport fail". Also, while trying to register I'm logged in to the asterisk CLI with verbose level 3 and debug level 4 and nothing appears. some more relevant data: I've added the following code to the end of my sip.conf.sample file: [demo-alice] type=friend host=dynamic secret=verysecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 [demo-bob] type=friend host=dynamic secret=othersecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 After I changed the sip.conf.sample file, I've created a copy of it and named it sip.conf. then I logged in to the asterisk CLI and typed sip reload. Then I'm trying to register and ekiga client from my host machine at 192.168.1.2 but it doesn't work and nothing appears on the asterisk CLI while in verbose mode level 3. BTW, If there is missing information about my question, please don't close it. comment about what you need to know and I'll edit it in to the question. tnx.

    Read the article

  • 2012 R2 services will not start after promotion to Domain Controller

    - by Cybersylum
    Having a peculiar issue promoting a Windows 2012 R2 server in a domain at 2003 domain/forest functional level. Built a new 2012 R2 server, added the following software (labtech, appassure, eset A/V, & Teamviewer). It activated and appeared to be working fine. I added the Active Directory Domain Services role, and completed the configuration (Domain/Forest Prep, and DC promotion). All appeared to go well. I rebooted the server, and that's where the peculiar stuff began. I noticed the server indicated it needed activated again; but would not accept the key. I verified the key was good. That's when I noticed the Software Protection service (as well as many other core services - Base Filtering engine, DHCP client, firewall, etc) would not start. The error message for all of them was "Access Denied". I called MS, and they wanted to troubleshoot at a service level. Their fix was to use procmon and identify the resource that needed permissions (registry key, file or folder) and add "everyone" with full control). That got the services to start; but the problem re-appeared after a reboot. Thinking the issue might have been with the anti-virus package during the promotion process, I rebuilt the DCs from scratch and removed the metadata from AD (as I could not demote the machines "rpc server unavailble"). I tried to promote the newly built machines again. The only changes to the brand new machines being critical updates. Again the promotion appeared to work fine; but upon reboot (and a long wait to allow replication to occur) similar problems began to re-appear. I have verified that the schema updates are correct (schema version is 69 - for Windows 2012 R2). I am not finding much about this issue through my own searches, so I thought I would post this to see if anyone else has seen anything similar...

    Read the article

  • How to access Virtual machine using powershell script

    - by Sheetal
    I want to access the virtual machine using powershell script. For that I used below script, Enter-PSSession -computername sheetal-VDD -credential compose04.com\abc.xyz1 where, sheetal-VDD is hostname of virtual machine compose04.com is the domain name of virtual machine and abc.xyz1 is the username of virtual machine After entering above command , it asks for password. When the password is entered I get below error, Enter-PSSession : Connecting to remote server failed with the following error message : WinRM cannot process the reques t. The following error occured while using Kerberos authentication: There are currently no logon servers available to s ervice the logon request. Possible causes are: -The user name or password specified are invalid. -Kerberos is used when no authentication method and no user name are specified. -Kerberos accepts domain user names, but not local user names. -The Service Principal Name (SPN) for the remote computer name and port does not exist. -The client and remote computers are in different domains and there is no trust between the two domains. After checking for the above issues, try the following: -Check the Event Viewer for events related to authentication. -Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or us e HTTPS transport. Note that computers in the TrustedHosts list might not be authenticated. -For more information about WinRM configuration, run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. At line:1 char:16 + Enter-PSSession <<<< -computername sheetal-VDD -credential compose04.com\Sheetal.Varpe + CategoryInfo : InvalidArgument: (sheetal-VDD:String) [Enter-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CreateRemoteRunspaceFailed Can someone help me out in this?

    Read the article

  • 'Future-proof' Live Audio Capture & Broadcast [migrated]

    - by maxpowers
    I'm looking to implement some live audio broadcasting functionality within a Ruby on Rails site for a client and was hoping I could get some input from people who have tackled this type of thing before. Essentially what I need to do is capture and record a user's audio (via microhpone, line in, etc), then stream that to 1,000+ listeners with very little latency, like sub 2 second if possible. So it looks like we've got 3 parts: Web-based audio capture (likely with Flash or JS) Server to accept audio feed and stream to listeners (likely Icecast or Wowza) Actual audio player (maybe HTML5 w/ Flash as a fallback? Maybe this jPlayer fork) Does RTMP makes sense here? Or maybe HTTP? What's the most 'future-proof' way to make this happen? Building with mobile in mind, but still want to be able stream to anyone. I've found lots of potentially helpful threads and software but I'm struggling to get an idea of how it all fits together. I'm a front end guy and way out of my comfort zone so if anyone has insights to offer, I'd love to hear them.

    Read the article

  • How would I write a terminal command to download a folder with wget from a Media Temple (gs) server?

    - by racl101
    I'm trying to download a folder using wget on the Terminal (I'm usin a Mac if that matters) because my ftp client sucks and keeps timing out. It doesn't stay connected for long. So I was wondering if I could use wget to connect via ftp protocol to the server to download the directory in question. I have searched around in the internet for this and have attempted to write the command but it keeps failing. So assuming the following: ftp username is: [email protected] ftp host is: ftp.s12345.gridserver.com ftp password is: somepassword I have tried to write the command in the following ways: wget -r ftp://[email protected]:[email protected]/path/to/desired/folder/ wget -r ftp://serveradmin:[email protected]/path/to/desired/folder/ When I try the first way I get this error: Bad port number. When I try the second way I get a little further but I get this error: Resolving s12345.gridserver.com... 71.46.226.79 Connecting to s12345.gridserver.com|71.46.226.79|:21... connected. Logging in as serveradmin ... Login incorrect. What could I be doing wrong?

    Read the article

  • wireless to wired internet

    - by Mark T
    My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

    Read the article

  • Why is my rsync so slow?

    - by iblue
    My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

    Read the article

  • Remote offscreen rendering

    - by redmoskito
    My research lab recently added a server that has a beefy NVIDIA graphics card, which we would like to use to do scientific computations. Since it isn't a workstation, we'll have to run our jobs remotely, over an ssh connection. Most of our applications require doing opengl rendering to an offscreen buffer, then doing image analysis on the result in CUDA. My initial investigation suggests that X11 forwarding is a bad idea, because opengl rendering will occur on the client machine (or rather the X11 server--what a confusing naming convention!) and will suffer network bottlenecks when sending our massive textures. We will never need to display the output, so it seems like X11 forwarding shouldn't be necessary, but Opengl needs the $DISPLAY to be set to something valid or our applications won't run. I'm sure render farms exist that do this, but how is it accomplished? I think this is probably a simple X11 configuration issue, but I'm too unfamiliar with it to know where to start. We're running Ubuntu server 10.04, with no gdm, gnome, etc installed. However, xserver-xorg package is installed.

    Read the article

  • PXELinux and compressed kernels/images

    - by Yvan JANSSENS
    Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

    Read the article

  • How do I speed up and cache mmap file access over NFS on Linux?

    - by Zan Lynx
    The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

    Read the article

  • Centos VM serving multiple public IP: how to configure network interface?

    - by Glasnhost
    I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Host is missing hostname and/or domain

    - by anlawang
    i use puppet 0.25.4 on ubuntu 10.04,when puppet installed ,i got the infor below : Nov 29 10:30:30 puppet puppetmasterd[4422]: Host is missing hostname and/or domain: pclient.example.com Nov 29 10:30:30 puppet puppetmasterd[4422]: Compiled catalog for pclient.example.com in 0.02 seconds i dont know how to fix it ,who can help me thank you ! my configuration : I use apt-get to install the puppet,so some configuration have been fixed puppet.conf on client : > [main] server=puppet.example.com > logdir=/var/log/puppet > vardir=/var/lib/puppet > ssldir=/var/lib/puppet/ssl > rundir=/var/run/puppet > factpath=$vardir/lib/facter > pluginsync=false > templatedir=$confdir/templates > prerun_command=/etc/puppet/etckeeper-commit-pre > postrun_command=/etc/puppet/etckeeper-commit-post > certname=pclient.example.com > node_name=cert [puppetd] > runinterval=30 puppet.conf on server: > [main] logdir=/var/log/puppet > vardir=/var/lib/puppet > ssldir=/var/lib/puppet/ssl > rundir=/var/run/puppet > factpath=$vardir/lib/facter > pluginsync=true > templatedir=$confdir/templates > prerun_command=/etc/puppet/etckeeper-commit-pre > postrun_command=/etc/puppet/etckeeper-commit-post i user the default node on site.pp i am a newer to puppet,so i dont know the reason for these problems!! thank you again!!!

    Read the article

  • Tuning up a MySQL server

    - by NinjaCat
    I inherited a mysql server, and so I've started with running the MySQLTuner.pl script. I am not a MySQL expert but I can see that there is definitely a mess here. I'm not looking to go after every single thing that needs fixing and tuning, but I do want to grab the major, low hanging fruit. Total Memory on the system is: 512MB. Yes, I know it's low, but it's what we have for the time being. Here's what the script had to say: General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Your applications are not closing MySQL connections properly Variables to adjust: query_cache_limit (> 1M, or use smaller result sets) tmp_table_size (> 16M) max_heap_table_size (> 16M) table_cache (> 64) innodb_buffer_pool_size (>= 326M) For the variables that it recommends that I adjust, I don't even see most of them in the mysql.cnf file. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_buffer_pool_size = 220M innodb_flush_log_at_trx_commit = 2 innodb_file_per_table = 1 innodb_thread_concurrency = 32 skip-locking big-tables max_connections = 50 innodb_lock_wait_timeout = 600 slave_transaction_retries = 10 innodb_table_locks = 0 innodb_additional_mem_pool_size = 20M user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = localhost key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 4 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M log_error = /var/log/mysql/error.log expire_logs_days = 10 max_binlog_size = 100M skip-locking innodb_file_per_table = 1 big-tables [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M !includedir /etc/mysql/conf.d/

    Read the article

  • Route all traffic of home network through VPN

    - by user436118
    I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

    Read the article

  • Updating files with a Perforce trigger before submit [migrated]

    - by phantom-99w
    I understand that this question has, in essence, already been asked, but that question did not have an unequivocal answer, so please bear with me. Background: In my company, we use Perforce submission numbers as part of our versioning. Regardless of whether this is a correct method or not, that is how things are. Currently, many developers do separate submissions for code and documentation: first the code and then the documentation to update the client-facing docs with what the new version numbers should be. I would like to streamline this process. My thoughts are as follows: create a Perforce trigger (which runs on the server side) which scans the submitted documentation files (such as .txt) for a unique term (such as #####PERFORCE##CHANGELIST##NUMBER###ROFL###LOL###WHATEVER#####) and then replaces it with the value of what the change list would be when submitted. I already know how to determine this value. What I cannot figure out, is how or where to update the files. I have already determined that using the change-content trigger (whether possible or not), which "fire[s] after changelist creation and file transfer, but prior to committing the submit to the database", is the way to go. At this point the files need to exist somewhere on the server. How do I determine the (temporary?) location of these files from within, say, a Python script so that I can update or sed to replace the placeholder value with the intended value? The online documentation for Perforce which I have found so far have not been very explicit on whether this is possible or how the mechanics of a submission at this stage would work.

    Read the article

  • java warnings on linux

    - by Geo Papas
    Hello i am getting warnings after i have installed java on kubuntu 11.10. The java programs run but i always get 4 warnings: $ java Warning: no leading - on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: missing VM type on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: no leading - on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: missing VM type on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' What am i missing? Thanks in advance! Here is the file content /usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg : /usr/lib/jvm/java-6-sun # # %W% %E% # # Copyright (c) 2006, Oracle and/or its affiliates. All rights reserved. # ORACLE PROPRIETARY/CONFIDENTIAL. Use is subject to license terms. # # List of JVMs that can be used as an option to java, javac, etc. # Order is important -- first in this list is the default JVM. # NOTE that this both this file and its format are UNSUPPORTED and # WILL GO AWAY in a future release. # # You may also select a JVM in an arbitrary location with the # "-XXaltjvm=<jvm_dir>" option, but that too is unsupported # and may not be available in a future release. # -server KNOWN -client IGNORE -hotspot ERROR -classic WARN -native ERROR -green ERROR

    Read the article

  • Nexenta, NFS and LOCK_EX

    - by Givre
    I'm currently using an LAMP architecture and I expect a big problem :( I have several http web server using PHP5. All are mounting via NFS (v3) the directory for all the hosted websites. The file server is running the Nexenta Storage Appliance using ZFS . The problem is all the NFS client trying to write something in a file over the NFS get this problem : This is inside the apache2 process: open("/nfs/website1/file.txt", ORDWR|OCREAT, 0600) = 11647 fstat(11647, {stmode=SIFREG|0600, st_size=23754, ...}) = 0 flock(11647, LOCK_EX And the process never get the LOCK and keep waiting for... always. The effect? All the apache2 procces get used and waiting.. my severs can't still proccess the others requests because there is no more proccess available. I don't now where to find a solution.. for me it.'s on the NFS server side.. but wich configuration is wrong or missing ? How can I find what is wrong? If you need more information about the configuration, just ask me what can help you more :)

    Read the article

  • Problem creating ODBC connection to SQL Server 2008 with Vista

    - by earlz
    Well, I'm trying to get a database schema thing working, first I tried just doing it in Linux where I'm more comfortable, but ODBC seems to be a hack there and I couldn't get it to work. So I figured it shouldn't be too hard in Windows.. Ok, so I created a SQL Server Client Alias so that I can simply same windowsserver to refer to my SQL server. Then, I went to the ODBC configuration in Control Panel. I clicked Add in the User DSN section. I chose Native SQL Server (10), and then clicked next. Then I typed a short name and a description and gave the servername as windowsserver/SQLEXPRESS Then, I click next, give it my user name and password and click next. Then, after like 2 minutes it says "Login Timeout Expired" What can be wrong here? I know the server is configured cause I have SQL Server Management Studio opened up with that server in it. I'm also just trying to connect over regular TCP/IP and my firewall is disabled.

    Read the article

  • Tell if IIS is being asked to serve compressed pages?

    - by Graham
    Hi, I'm trying to find out if our IIS server is being asked to serve pages compressed. I'm a noob regarding a lot of this so am working my way through the issues. We're using IIS 6.0 and have correctly turned compression on. If I use Fiddler2 to analyse the HTTP requests via localhost, then Fiddler reports that the pages are compressed. If we then access the server over the network, either via its external URL or via the internal server name, Fiddler reports those pages as uncompressed. Therefore, it's logical to assume that something is getting in the way - presumably our ISA server. Our ISA administrator states that ISA is configured to allow compressed requests but what I want to do is to look at the requests coming through to IIS to see if IIS is being asked to serve pages compressed. I'm fairly convinced that our request is going to ISA, ISA is forwarding these, but not with the "compression" details - therefore IIS is not performing any compression. I've looked at the IIS logs but can't see anything obvious about the HTTP request. Is there any way I can check, on the web server itself, this sort of information? One thing that is confusing, but it may be normal, is that the Client IP making the request is not the orignal PC (i.e. mine) and not the ISA firewall, but the web server itself... Thanks

    Read the article

< Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >