Search Results

Search found 70655 results on 2827 pages for 'python time'.

Page 719/2827 | < Previous Page | 715 716 717 718 719 720 721 722 723 724 725 726  | Next Page >

• Event Log "Wake Source" when system wakes from sleep

  - by Doltknuckle

  So I've been troubleshooting sleep timers for our systems and have run across an interesting issue. I need a way to report how long a system was awake after a number of different inputs. Now, I've discovered that the System Log tracks wake and sleep events and even tells you the times that everything happens at. The thing is doesn't tell you is what triggered the wake event. It does give you a numerical code however. Here are some examples of what I am finding. Index : 2901 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T23:20:06.097488100Z Wake Time: 2010-10-03T17:41:12.796400500Z Wake Source: 0 Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter -- Index : 2841 EntryType : Information InstanceId : 1 Message : The system has resumed from sleep. Sleep Time: 2010-10-01T19:19:37.239789600Z Wake Time: 2010-10-01T21:28:48.921200800Z Wake Source: 4HID Keyboard Device Category : (0) CategoryNumber : 0 Source : Microsoft-Windows-Power-Troubleshooter So here's my question: Does anyone know what the different numerical codes for the "Wake Source" mean? I think "0" is a magic packet and "4" is a USB device. Does anyone have any idea if there is any documentation out there on this for Windows 7? Thanks in advance

  Read the article

• Understanding RedHats recommended tuned profiles

  - by espenfjo

  We are going to roll out tuned (and numad) on ~1000 servers, the majority of them being VMware servers either on NetApp or 3Par storage. According to RedHats documentation we should choose the virtual-guestprofile. What it is doing can be seen here: tuned.conf We are changing the IO scheduler to NOOP as both VMware and the NetApp/3Par should do sufficient scheduling for us. However, after investigating a bit I am not sure why they are increasing vm.dirty_ratio and kernel.sched_min_granularity_ns. As far as I have understood increasing increasing vm.dirty_ratio to 40% will mean that for a server with 20GB ram, 8GB can be dirty at any given time unless vm.dirty_writeback_centisecsis hit first. And while flushing these 8GB all IO for the application will be blocked until the dirty pages are freed. Increasing the dirty_ratio would probably mean higher write performance at peaks as we now have a larger cache, but then again when the cache fills IO will be blocked for a considerably longer time (Several seconds). The other is why they are increasing the sched_min_granularity_ns. If I understand it correctly increasing this value will decrease the number of time slices per epoch(sched_latency_ns) meaning that running tasks will get more time to finish their work. I can understand this being a very good thing for applications with very few threads, but for eg. apache or other processes with a lot of threads would this not be counter-productive?

  Read the article

• prevalent, recurring hardrive failure intel macbook from 2006/2007

  - by SimonSalman

  Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

  Read the article

• samba4 not building in Arch

  - by kmplsv

  cp bin/tdbtool bin/tdbdump bin/tdbbackup /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/bin cp ./include/tdb.h /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/include cp tdb.pc /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/pkgconfig cp libtdb.a libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so rm -f /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 ln -s libtdb.so.1.2.4 /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/lib/libtdb.so.1 mkdir -p /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` cp tdb.so /tmp/yaourt-tmp-root/aur-samba4/pkg/`/tmp/yaourt-tmp-root/aur-samba4/src/bin/python -c "import distutils.sysconfig; print distutils.sysconfig.get_python_lib(1, prefix='/opt/samba4/samba')"` /bin/install -c -d /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8 for I in manpages/*.8; do \ /bin/install -c -m 644 $I /tmp/yaourt-tmp-root/aur-samba4/pkg//opt/samba4/samba/share/man/man8; \ done /bin/install: cannot stat `manpages/*.8': No such file or directory make: *** [installdocs] Error 1 Aborting... ==> ERROR: Makepkg was unable to build samba4. ==> Restart building samba4 ? [y/N] ==> ------------------------------- ==>c Any ideas as what is causing my build to fail? I assume it's an issue with manpages I can't figure out exactly what package it is looking for that I don't have.

  Read the article

• Backup script to FTP with timed subfolders

  - by Frederik Nielsen

  I want to make a backup script, that makes a .tar.gz of a folder I define, say fx /root/tekkit/world This .tar.gz file should then be uploaded to a FTP server, named by the time it was uploaded, for example: 07-10-2012-13-00.tar.gz How should such backup script be written? I already figured out the .tar.gz part - just need the naming and the uploading to FTP. I know that FTP is not the most secure way to do it, but as it is non-sensitive data, and FTP is the only option I have, it will do. Edit: I ended up with this script: #!/bin/bash # have some path predefined for backup unless one is provided as first argument BACKUP_DIR="/root/tekkit/world/" TMP_DIR="/tmp/tekkitbackup/" FINISH_DIR="/tmp/tekkitfinished/" # construct name for our archive TIME=$(date +%d-%m-%Y-%H-%M) if [ $1 ]; then BACKUP_DIR="$1" fi echo "Backing up dir ... $BACKUP_DIR" mkdir $TMP_DIR cp -R $BACKUP_DIR $TMP_DIR cd $FINISH_DIR tar czvfp tekkit-$TIME.tar.gz -C $TMP_DIR . # create upload script for lftp cat <<EOF> lftp.upload.script open server user user password lcd $FINISH_DIR mput tekkit-$TIME.tar.gz exit EOF # start backup using lftp and script we created; if all went well print simple message and clean up lftp -f lftp.upload.script && ( echo Upload successfull ; rm lftp.upload.script )

  Read the article

• Postfix qmgr process causes heavy overload on mailservers

  - by Mattias

  We are using Postfix as MTA for our e-mailmarketing software and once in a while we see that the load on one of the mailservers rises above 5. The load is caused by the qmgr-process which is the heart of Postfix and I see that it is consuming a lot of CPU resources. The process seems to be stuck because after 15 minutes it is still doing the samething and still increasing the load. Once I restart the postfix service the load rapidly decreases to below 1 and Postfix continues to send e-mails without any problems. I'm wondering if anyone else has encountered this problem and if people have suggestions on how to prevent it. The problem shows up on all our mailservers but almost never at more than 1 at the time. It seems to be triggered only when we are sending a mailing but the size (10 or 100.000 e-mails doesn't seem to make a difference). It maybe happens once a week or even less often and the time and day is also different every time. We tried to solve the problem by decreasing the amount of messages qmgr is allowed to process but this didn't solve it. We are using Postfix 2.5.5 on Debian Lenny 5.0.8 (postfix is installed through the default Debian repository). No special messages can be found in the logs (syslog, messages, mail.*). Thank you for your time

  Read the article

• How to test nginx proxy timeouts

  - by mkorszun

  Target: I would like to test all Nginx proxy timeout parameters in very simple scenario. My first approach was to create really simple HTTP server and put some timeouts: Between listen and accept to test proxy_connect_timeout Between accept and read to test proxy_send_timeout Between read and send to test proxy_read_timeout Test: 1) Server code (python): import socket import os import time import threading def http_resp(conn): conn.send("HTTP/1.1 200 OK\r\n") conn.send("Content-Length: 0\r\n") conn.send("Content-Type: text/xml\r\n\r\n\r\n") def do(conn, addr): print 'Connected by', addr print 'Sleeping before reading data...' time.sleep(0) # Set to test proxy_send_timeout data = conn.recv(1024) print 'Sleeping before sending data...' time.sleep(0) # Set to test proxy_read_timeout http_resp(conn) print 'End of data stream, closing connection' conn.close() def main(): s = socket.socket(socket.AF_INET, socket.SOCK_STREAM) s.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, 1) s.bind(('', int(os.environ['PORT']))) s.listen(1) print 'Sleeping before accept...' time.sleep(130) # Set to test proxy_connect_timeout while 1: conn, addr = s.accept() t = threading.Thread(target=do, args=(conn, addr)) t.start() if __name__ == "__main__": main() 2) Nginx configuration: I have extended Nginx default configuration by setting explicitly proxy_connect_timeout and adding proxy_pass pointing to my local HTTP server: location / { proxy_pass http://localhost:8888; proxy_connect_timeout 200; } 3) Observation: proxy_connect_timeout - Even though setting it to 200s and sleeping only 130s between listen and accept Nginx returns 504 after ~60s which might be because of the default proxy_read_timeout value. I do not understand how proxy_read_timeout could affect connection at so early stage (before accept). I would expect 200 here. Please explain! proxy_send_timeout - I am not sure if my approach to test proxy_send_timeout is correct - i think i still do not understand this parameter correctly. After all, delay between accept and read does not force proxy_send_timeout. proxy_read_timeout - it seems to be pretty straightforward. Setting delay between read and write does the job. So I guess my assumptions are wrong and probably I do not understand proxy_connect and proxy_send timeouts properly. Can some explain them to me using above test if possible (or modifying if required).

  Read the article

• Cache-control for permanent 301 redirects nginx

  - by gansbrest

  I was wondering if there is a way to control lifetime of the redirects in Nginx? We would liek to cache 301 redirects in CDN for specific amount of time, let say 20 minutes and the CDN is controlled by the standard caching headers. By default there is no Cache-control or Expires directives with the Nginx redirect. That could cause the redirect to be cached for a really long time. By having specific redirect lifetime the system could have a chance to correct itself, knowing that even "permanent" redirect change from time to time.. The other thing is that those redirects are included from the Server block, which according the nginx specification should be evaluated before locations. I tried to add add_header Cache-Control "max-age=1200, public"; to the bottom of the redirects file, but the problem is that Cache-control gets added twice - first comes let say from the backend script and the other one added by the add_header directive.. In Apache there is the environment variable trick to control headers for rewrites: RewriteRule /taxonomy/term/(\d+)/feed /taxonomy/term/$1 [R=301,E=expire:1] Header always set Cache-Control "store, max-age=1200" env=expire But I'm not sure how to accomplish this in Nginx.

  Read the article

• open-source LAMP package for simple accouting and receiving?

  - by user26664

  Hello. I am involved with a computer-based charity where we take donation of old equipment, often recycle it, mostly rehabilitate it and make it available through grants and 'adoptions', and sell some items. What we're looking for is a LAMP package that can handle our records of donations of equipment, print receipts for donators, and also track our thrift store sales with receipts. Donators will want receipts of their donations for tax deduction purposes. We'll want to print reports of incoming items from time to time, say monthly and yearly. For the thrift store, we'll also need receipts for that, reports of cash, especially for reconciling cash drops, and also reports of items sold from time to time. I'm thinking this might be a single package, but it might be two. We don't want to track our shop inventory with either of these programs -- that's another program/project. We just need to know what was donated and what was sold. It must be open source, and ideally we'd like it to run on LAMP -- Linux, Apache, MySQL, PHP, but we will consider other open-source platforms.

  Read the article

• Online computer not responding to pings

  - by mastercork889

  I was doing a bit of scanning on my network lately, knew all the hostnames to each computer connected. But whilst pinging one of them ping returned Request timed out.. This is strange as I know the computer is online and that the computer responds correctly to pinging on a different (enterprise) network. Is there something on the computer, my network, or my computer that is bugging with this? - That's just a sub-question, I don't expect this to be the main answer. The real question: Why does this happen? Why does pinging the IP4 address not work? EDIT : Pinging the Hostname used to default to the IP4 address, but now it defaults to the IP6 address. Why does this happen? But now that it pings using IP6, how come it all of a sudden works? > ping -6 THE_COMPUTER Pinging THE_COMPUTER [lengthy IP6 address] with 32 bytes of data: Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Ping stats: Sent = 4, Recieved = 4, Lost = 0 (0% loss) But when this is done using IP4 it doesn't work. So there are now two questions: How come IP6 works and not IP4? Why does IP4 not work?

  Read the article

• Anyone know a good mind mapper that works with a scheduler?

  - by GLycan

  TL;DR: Mind mapping tasks to be processed into a schedule based on task metadata. I have all sorts of ideas about what to invest resources (mainly time) in, but when I actually have time to do something I useually end up browsing reddit for not knowing what do to, and the frequancy with which I forget deadlines scares me. I'd love to bring order and structure into my mind, and always know what to do next. So, I want a mind mapping app, where I'd give each branch (types and subtypes of things I want to do) a importance score (if there were two branches, and one had 60 while the other 40, they would respectivily get 60% and 40% of the parent's importance, with the root being 100) and a how soon that branch should be revised/updated (an hobby I want to try out might be checked, say, once a week, while a school subject should be checked once a day) and give each leaf (something I want/need to do) how much time it takes, deadline (if any), and optionally an absolute importance, reoccurrence (guitar practice might repeat once a week), and prerequisites (reading something requires that book (although that could be brought somewhere), coding requires a box, jogging requires being outside) and maybe some other flags, like if it's enjoyable or not. It should either be packaged or working with a schedular app, to which I'd say, look, my day works this way (completely busy from 8 to 9:15, then 15 minutes of being inside with nothing, ..., two hours with box and possibility to go outside, etc), saying that such-and-such pattern is school and happens ever weekday except such-and-such days. The output should be of the form of a schedule, fit for printing or, when I finally get an android, mobile viewing, that schedules tasks with regards to availability of resources and importance (importance being derived from the leaf-task's parent branches), and the set of flags (all work and no play makes me a dull boy). One of these tasks should be reviewing anything that should be updated on that day, including future day layouts (e.g, if the time slots of future days have changed. This should be done every day.) Does anyone know some collection of preferably open-source (or free, or pirateable) tools, or better yet a single one, that accomplishes this task? I know python pretty well, and should be able to write any necessary glue.

  Read the article

• Eclipse on Ubuntu: Rectangles instead of Strings and some Java methods and classes

  - by Claus Hausberger

  after upgrading from Ubuntu 9.04. to 11.04 (new installation), I have weird problems with the Eclipse editor. With the Eclipse PyDev plugin, whenever I typ single quoted strings like 'bla', they appear as rectangles (both the quotes as well as the string). First I thought this was a problem with the PyDev plugin, but it also happens with Java and Scala Plugins. With Java, it happens, for example, when typing System.out.println("bla") and then "out" is shown as rectangles only. Weird is that for about half a second I see "System.out.println" and then the editor changes it to System.[][][].println (not really [] (here I used two brackets), it is shown as rectangles). This is very weird. I've never had this before with any Ubuntu, Java or Eclipse version. Currently, I use: Ubuntu 11.04. Eclipse 3.6 Java 1.6.0_25 The latest plugins for Python (2.1) and Scala (beta 5) where used. Eclipse and Ubuntu Terminal is set to UTF-8. The problem also happens when using KDE instead of Gnome. I doubt is has anything to do with Java as I use the same versions on older Ubuntu installations (10.04, 9.10, etc) at work. It does not happen with Netbeans. But I saw once error dialog message from the Update Manager where there were some rectangles in the error widget. Maybe this is the same problem Any ideas what could be wrong here and how to fix this? Eclipse is unusable but I need this for work and also for Scala and Python (the Eclipse plugins for those are very good now). Claus

  Read the article

• Is VGA port hot-pluggable?

  - by Martin Bøgelund

  In meetings, I often see people detaching the VGA connector from one running laptop and connecting it to another, while the projector is still on. Is this 100% risk free, and OK by design of the VGA standard? If there's a risk involved in hot-plugging VGA, can it be removed by turning off or suspending either laptop, display, or both? I see this being done all the time without causing disaster, so clearly I'm not interested in answers stating "we do it all the time, so it should be OK!". I want to know if there's a risk - real or in theory - that something breaks when doing this. EDIT: I did an internet search on the topic, and I never found a clear statement as to why it is safe or unsafe to hot swap VGA devices. The typical form is a forum question asking basically the same question as I did, and the following types of statements Yes it's hot swappable! I do it all the time! It involves some kind of risk, so don't do it! You're some kind of moron if you think there's a risk, so just do it! But no explanation as to why it safe or not... Joe Taylors answer below contains a link to a forum post and answers that basically give me the same statements as mentioned above. But again, no good explanation why. So I looked for an actual manual for a projector, and found "Lenovo C500 Projector User’s Guide". It states on page 3-1: Connecting devices Computers and video devices can be connected to the projector at the same time. Check the user’s manual of the connecting device to confirm that it has the appropriate output connector. [image] Attention: As a safety precaution, disconnect all power to the projector and devices before making connections. But again, no good explanation.

  Read the article

• How to convert Markdown files to Dokuwiki, on a PC

  - by Clare Macrae

  I'm looking for a tool or script to convert Markdown files to Dokuwiki format, that will run on a PC. This is so that I can use MarkdownPad on a PC to create initial drafts of documents, and then convert them to Dokuwiki format, to upload to a Dokuwiki installation that I have no control over. (This means that the Markdown plugin is no use to me.) I could spend time writing a Python script to do the conversion myself, but I'd like to avoid spending time on this, if such a thing exists already. The Markdown tags I'd like to have supported/converted are: Heading levels 1 - 5 Bold, italic, underline, fixed width font Numbered and unnumbered lists Hyperlinks Horizontal rules Does such a tool exist, or is there a good starting point available? Things I've found and considered I initially thought that txt2tags would be helpful, but although it can write both markdown and Dokuwiki, it is very tied to its own specific input format I've also seen Markdown2Dokuwiki, and although I'd certainly be willing to use a sed script, even on a PC, this only supports a tiny, tiny part of Markdown's syntax. python-markdown2 also sounded promising, but it only writes out HTML. pandoc - but it doesn't support Dokuwiki output MultiMarkdown - does not appear to support Dokuwiki output

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

  Read the article

• I deployed Flash Player via a Software Installation policy. How to upgrade?

  - by eleven81

  I have a Windows Server 2008 machine as my DC. Earlier this year I created a Software Installation GPO to deploy Adobe Flash Player plugin MSI. I assigned the policy to the computers, about half run Windows XP x86 and the other half Windows 7 x64. That all works like clockwork. When I created the Software Installation Policy, I disabled the Flash Player plugin's automatic update feature by editing the MSI in Orca. I did this because I wanted all of my machines to run the exact same version of the plugin. Now, some time has passed and a newer version of the Flash Player plugin has been released. It is time for me to push out the updated version of the plugin. I already have the new MSI, but I am lost on what to do next. I see the upgrades tab in the Software Installation GPO, but everything there reads like that would be used for add-ons to a larger master program and not for updates that are released over time. I have read that it is best to create a new Software Installation policy with the new MSI, revoke the old GPO, and assign the new GPO. I feel as though, over time, I will wind up with more revoked policies than active ones. I have also read that some people have had success by replacing the old MSI with the new MSI and simply telling the GPO to redeploy. This seems like a backdoor method that will only get me in to trouble. In short, what is the correct, best-practice, or preferred way to roll out the new version via Group Policy?

  Read the article

• I'm looking for a program that can automate opening/closing a program

  - by Peterstone

  I am looking a for a program to remember things with these features: Open files or programs in my own computer at a planned time. For example I want every morming at 8:00 the program open a particular mp3 file. But suposse, by mistake, that I on my computer and 9:00, then I want that the program rememberme what I planned to open at 8:00. Show me the program as an active windows on my desktop. The windows of the program opened is what the user is seeing (Is at the first place in the desktop) and the rest of the program windows are below. Close programs or files in my own computer at a planned time. For example I want that the program mp3 file that was opened at 8:00 was closed at 10:00 if at that time still be opened. Detection of events. For instance If I open particular videogame program. then a mp3 file (with a recording message arguing why I shouldn´t continue playing that videogame at work time) is opened. Possibility of combine the features mentioned before each other.

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• How to set static ip address on vmware for NAT guest vms from an ubuntu Host dhcp server?

  - by javadba

  I need to configure various linux flavor NAT'ed guest vm's to have static ip addresses provided by the Ubuntu host. The vmware documentation punts on this topic, deferring to "see the man pages for your linux distribution". But the generic pages for "my linux distro" do not know about the special stuff for vmware e.g. vmnet8. Pointers from someone who just knows how to do this would be much appreciated. Here is the /etc/vmware/vmnet8/dhcpd/dhcpd.conf: allow unknown-clients; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours subnet 192.168.238.0 netmask 255.255.255.0 { range 192.168.238.128 192.168.238.254; option broadcast-address 192.168.238.255; option domain-name-servers 192.168.238.2; option domain-name localdomain; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours option netbios-name-servers 192.168.238.2; option routers 192.168.238.2; } host vmnet8 { hardware ethernet 00:50:56:C0:00:08; fixed-address 192.168.238.1; option domain-name-servers 0.0.0.0; option domain-name ""; option routers 0.0.0.0; } Fromt the dhcpd.conf documentation, we are supposed to add an entry for static hosts similar to the following: host mystatichostonee { hardware ethernet 00:20:6B:C7:9B:E4; fixed-address 192.168.238.101; } host mystatichosttwo { hardware ethernet 00:23:7a:C7:9c:F2; fixed-address 192.168.238.102; } But notice that the vmnet8 entry in the vmware-generated dhcpd.conf already is set to fixed-address. I don't know how to add the specifics for my hosts to that vmnet8 entry: do they become nested?

  Read the article

• HP Photosmart C4780 printer/scanner breaks netgear WNDR3700v3 router on connection

  - by CodeJunkie

  A few months ago, we upgraded our Netgear router's firmware. Immediately, we started having trouble connecting to the internet. Each time this problem would happen, every device in the house would stop being able to make new connections to the internet. For example, you couldn't open new pages in the browser, but if Skype was running when the problem happened, you could keep talking to people. The only solution to this problem seemed to be resetting the router to factory defaults. Eventually, we solved this problem by just downgrading the router firmware. A while later, we got a new Netgear router. Almost right away, the new router started having exactly the same problems as the old one did on current firmware. The network connection would stay active and the computer would say it had an internet connection, but you couldn't do anything online except for using Skype. We eventually figured out that this happens every time our HP printer gets onto the network. Any time the printer gets onto the wireless network, the whole network stops connecting to the internet almost completely. The only thing that will fix it at that point is to reset the router to factory specs, and unplug the printer so it can't get back onto the network. The Netgear router has the latest version of the firmware, but the printer/scanner is very old. It looks to me like this problem is probably a result of a firmware conflict between the printer and the router, but I'm not sure how to fix that problem. Here's some additional information: Printer: HP Photosmart C4780 Router: WNDR3700v3 Router firmware: V1.0.0.22_1.0.17 (Stock, up to date firmware) Why would the printer getting on the network cause the router to not be able to access the internet correctly until it was reset? What can be done to allow the printer to be on the network without breaking the network for all other devices? Edit: One other thing that happens during this internet problem is that multiple computers in the house display an "IP conflict" message repeatedly, and extremely frequently (as often as every five to ten minutes, and every time a connection to the wireless is made).

  Read the article

• Failed to re-publish a page - Tridion 2011 SP1

  - by Wilson Yu

  We are getting some strange error when re-publishing the same page. The page was published successfully the first time and we can see the page from presentation server. It failed with the following error (see below) when we tried to publish it again (no change to page). The page ran OK within template builder and we got the correct html output, it failed in the last committing deployment step (Prepare Transport, Transporting, Preparing Deployment and Deploying are all successful). Once it fails to publish the second time, it always fails to publish, and we can't un-publish it either. Also when we make a copy of the failed page and create a new page, we can publish the new page first time, the new page then fails to publush the second time with the same error. Does anyone know what would cause this error? any help would be greatly appreciated. Here is the error msg: Committing Deployment Failed Phase: Deployment Prepare Commit Phase failed, Unable to prepare transaction: tcm:0-4210-66560, For input string: "", For input string: "", Unable to prepare transaction: tcm:0-4210-66560, For input string: "", For input string: ""

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• On Windows machines, what is the typical toolchain for remote maintenance?

  - by Hanno Fietz

  I need to deploy PHP and Python code and the appropriate environment (web server, db server) to remote Windows systems, and I don't know what toolchain would be the equivalent to ssh, scp, bash and the like. So, basically, what I need to be able to do is the following: access remote Windows with the appropriate privileges in a secure manner, like I routinely do with ssh (I don't even know whether that would be a text or graphic interface on Windows). remotely install software: Apache or IIS, MySQL or Postgres, Python or PHP copy files from remote (the application we're deploying) remotely configure the machine to run regular tasks (e. g. checking for updates to the application) automate tasks like downloading files from a designated place The main question is probably how I get onto the machine securely in the first place, and then the rest is general Windows admin knowledge, which probably is too broad a scope to fit into one question. I have years of experience with maintaining Linux boxes and I have used tools of varying sophistication on those, ranging from plain scping of PHP files to deployment of Java application containers and even full VMs with Vagrant. On Windows, I'm a complete noob, and I don't even know where to start. I have installed Apache, MySQL , PHP on a desktop machine maybe twice in my life, that's about it. Bonus points for things that work from a Linux machine at my end, but I could run a VM and do everything from there.

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

< Previous Page | 715 716 717 718 719 720 721 722 723 724 725 726  | Next Page >