Search Results

Search found 22405 results on 897 pages for 'message threading'.

Page 722/897 | < Previous Page | 718 719 720 721 722 723 724 725 726 727 728 729  | Next Page >

• Linux: 3 Monitor PCI-e Graphics card (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. I'll post the exact error message here soon, but it's very useless. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment. Thanks, Nick

  Read the article

• mail server checklist..

  - by Jeff

  currently we ran into some issues with our mail server setup. im preparing a list of actions that we should enforce and use in order to maintain a proper email solution within our company. we have around 80 exchange users, and send mass emails out almost on a monthly bases to 20,000 + customers each time.. the checklist i currently have: 1) mcafee mxlogic 'cloud' anti-spam functionality for incoming message. 2) antivirus on each computer in company 3) antivirus on exchange and DNS servers 4) setup SPF record 5) setup DKIM 6) setup domainkey 7) setup senderID 8) submit spf to microsoft, yahoo, etc. for 'whitelist' purposes. 9) configure size limits for messages in exchange to safe numbers 10) i have 2 outside IPs for my email server, incase one gets blacklisted, switch to the backup. 11) my internet site rests on a different ip than the mail server 12) all mass emails for company sent through 3rd party company (listtrak.com) 13) setup domain alias, media, enews, and bounce for the 3rd party mass mail software. 14) verify the setup using [email protected] 15) configure group policy and our opendns.org account to prevent unwanted actions and website viewing mass emails: 1) schedule them to send different amounts at different times (1,000 at 10am, 1,000 at 4pm, 1,000 10am next day).. 2) setup user prefences, decide what they want to receive ect. ( there interests) 3) send a more steady flow of email, maybe 100 a week with top new products instead of 20,000k every other month.. if anyone has suggestions or additions/subtractions to this checklist they are greatly appreciated. thank you

  Read the article

• Permissions error when creating desktop shortcut

  - by Ryan M.

  Hey guys, I have a user that's got a weird permissions problem on Windows 7. He's trying to create a shortcut for Outlook on his desktop(he doesn't want it in his start menu or his taskbar...). If we right click the outlook.exe and do Send to Desktop, it works just fine. If we do a search for "outlook" in the search bar, and then try and drag and drop the outlook icon to the desktop, we get the error message "You need Permission to perform this action. You require permission from SYSTEM to make changes to this file: Microsoft Office Outlook 2007". Dragging and dropping other exe's onto the desktop work just fine. They create shortcuts without any problems. But if I try to do ANY of the Office programs (Word, Excel, Outlook, etc..) I get this permission error. Any ideas? He's using an A.D. account and he's in the local administrators group. He's an executive so he's not accepting "this isn't a real problem because I found another way to make a shortcut" as an answer. Any help is appreciated.

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• 412 Precodition Failed error only occurs on certain networks

  - by Andy

  One of my favorite websites: http://jessiejofficial.com (yes, I'm a Jessie J Fan :')) has recently started displaying the error message "412 Precondition Failed" whenever I visit it from my home network, even when I use Tor Browser. At first I thought that this was an issue with the whole website, however I have contacted the web developer and he has said that they has been plenty of hits within the last 48 hours. Plus, I discovered tonight that I can access the website from my phone, through the mobile network. So it appears to just be my network as all of the devices in my house connected to the WiFi display the same error when I try to visit any page of the site. However there have been no changes that we are aware of or are noticeable to our network since the website was accessible, and I have just heard that another person in a different part of the country is experiencing the same difficulties also. Any help/advice/suggestions would be appreciated greatly Update: When trying to ping 'jessiejofficial.com' in Windows command prompt the request times out on all four attempts, on any computer connected to the wireless network. I can now also confirm that the same thing occurs on my MacBook Pro.

  Read the article

• Static IP addressing issue in Ubuntu on BeagleBoneBlack Rev C

  - by Stringfellow

  I have my BBB configured to use a static IP address using the following in the file /etc/network/interfaces: allow-hotplug eth0 iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 network 192.168.0.0 This seems to work ok on boot, but when the ethernet cable is unplugged and then plugged back in, I lose the IP address. Any ideas what's going on here? Another weird symptom: If I boot the BBB with the network cable unplugged, but the switch it's plugged into off, I'll get my static IP. But, when I turn the switch on, I'll get a DHCP-assigned address. This is even though I have it configured with a static IP address. One last thing. If I ifdown etho, the interface will be gone when I do an ifconfig. If I wait a few seconds, though, and then re-run ifconfig, it will reappear, without an IP address. (Before I disabled IPv6, I used to get a IPv4 DHCP address in this case... weird). When that happens, I get a message like this in /var/log/messages: Apr 23 20:32:06 beaglebone kernel: [ 737.170172] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Apr 23 20:32:06 beaglebone kernel: [ 737.170304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Here's my uname -a: root@beaglebone:/etc# uname -a Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l GNU/Linux Any ideas what's going on here?

  Read the article

• Why Are SPF Records Failing?

  - by robobobobo

  Ok I've been going through various different sites, resources and topics here trying to figure out what is wrong with my SPF records but no matter what I do they don't seem to pass. Here's what I have "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" I've tried multiple different tools to check my spf records, some give me a pass, some don't. But I can't send mail to certain google app accounts, they just bounce back all the time which is very annoying. Anyone got any ideas? I have noticed that the source IP address is not the IPV4 addresses I've defined, but Cpanel wouldn't let me add that address into it.. And here's the result of tests I'm getting back from port25.com. I'm running WHM by the way and have enabled spf and dkim. Summary of Results SPF check: fail DomainKeys check: neutral DKIM check: pass Sender-ID check: fail SpamAssassin check: ham Details: HELO hostname: server1.viralbamboo.com Source IP: 2a01:258:f000:6:216:3eff:fe87:9379 mail-from: ###@viralbamboo.com SPF check details: Result: fail (not permitted) ID(s) verified: smtp.mailfrom=###@viralbamboo.com DNS record(s): viralbamboo.com. SPF (no records) viralbamboo.com. 13180 IN TXT "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" viralbamboo.com. AAAA (no records) viralbamboo.com. 13180 IN MX 0 viralbamboo.com. viralbamboo.com. AAAA (no records) DomainKeys check details: Result: neutral (message not signed) ID(s) verified: header.From=###@viralbamboo.com DNS record(s): DKIM check details: Result: pass (matches From: ###@viralbamboo.com). ID(s) verified: header.d=viralbamboo.com Canonicalized Headers: content-type:multipart/alternative;'20'boundary="4783D1BE-5685-41CF-B91B-1F15E91DD1E3"'0D''0A' date:Mon,'20'1'20'Jul'20'2013'20'21:30:47'20'+0000'0D''0A' subject:=?utf-8?Q?test?='0D''0A' to:"[email protected]?="'20''0D''0A' from:=?utf-8?Q?Rob_Boland_-_Viralbamboo?='20'<###@viralbamboo.com'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=viralbamboo.com;'20's=default;'20'h=Content-Type:Date:Subject:To:From:MIME-Version;'20'bh=CJMO7HYeyNVGvxttf/JspIMoLUiWNE6nlQUg5WjTGZQ=;'20'b=;

  Read the article

• Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

  - by AKa

  I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

  Read the article

• sharing a USB printer in SOHO environment [migrated]

  - by Registered User

  Here is a situation I am facing, there is USB printer which works only on a Windows XP machine, there are other devices in LAN it is a Small Office Home Office environment. How can this USB printer attached to Windows XP machine be shared so that other laptops or users in Network who have Windows 7 or Linux on their laptops can use this printer. The printer model number is Canon Laser Shot LBP-1210 http://www.canon-europe.com/For_Home/Product_Finder/Printers/Laser/LaserShot_LBP1210/index.asp a print server is not available to me I need to make it work in this situation only.What can I do? the clients are unable to connect to this.It is not a network or TCP/IP printer If a from Windows 7 machine some one wants to use this printer so that he can take a print he gets an error while adding the printer to his machine which is a Windows 7 machine (where as the printer is USB printer on Windows XP machine) Start--->Devices and Printers---> Add Printer---> Find Printer by name or IP address--->Selected a shared printer by name-->\\PC-Name-printer3 and select browse it gives a message Windows can not find a driver for Canon LASER SHOT LBP-1210 on the network what does this mean do I need to install some kind of software at client machine or on the machine where printer is present?

  Read the article

• "Document in ADF" on Canon MX340

  - by Michael Donohue

  I have a Canon MX340 multifunction printer. Recently, it keeps saying "Document in ADF" when I turn on the printer. I've tried clearing this multiple times, but as soon as the feeder wheels stop turning, in an attempt to clear the document feeder, it just pops up the same error again. This is particularly annoying, as it blocks all functions on the device - I cannot print, even though printing has no interaction with the document feeder. I've opened up the feeder device, as much as can be done with fingers alone. There just doesn't seem to be anything in there. I ran a sheet of paper through about six times, just to see if some dust might be getting in the way, and I've blown out the feeder with air. Still nothing. At this point, I don't care too much about the ADF working, I just want to disable whatever sensor is tripping this error message. Any ideas? I found this thread online, where a user has the same problem. But no resolution was reached there.

  Read the article

• Uploading to another domain gives HTTP code 405

  - by dragon112

  I'm trying to upload a file (which can be quite large) from the website of one server to the backend of another server using plupload. Lets say: domain 1 = http://www.websitedomain.com/uploadform domain 2 = http://www.backenddomain.com/uploadhandler Trying to upload i send the following: OPTIONS /main/uploadnetwork.php HTTP/1.1 Host: backenddomain.com Connection: keep-alive Access-Control-Request-Method: POST Origin: http://www.websitedomain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.79 Safari/537.4 Access-Control-Request-Headers: origin, content-type Accept: */* Referer: http://www.websitedomain.com/uploadform Accept-Encoding: gzip,deflate,sdch Accept-Language: nl-NL,nl;q=0.8,en-US;q=0.6,en;q=0.4 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 DNT: 1 But when I try to start the upload the server returns the following: HTTP/1.1 405 Method Not Allowed Allow: GET, HEAD, OPTIONS, TRACE Content-Type: text/html Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET X-Powered-By-Plesk: PleskWin Date: Mon, 01 Oct 2012 12:41:57 GMT Content-Length: 999 After doing some research I found out that a browser does this to check if the server will accept the intended message. It looks like my server doesn't feel like accepting a simple POST call even tho i use post all the time. The Google Chrome console gives the following error: XMLHttpRequest cannot load http://www.backenddomain.com/uploadhandler. Origin http://www.websitedomain.com is not allowed by Access-Control-Allow-Origin. Does anyone know how to stop the browser from checking or how i can tell my server to just accept the POST?

  Read the article

• What is the --daemon option?

  - by Pascal Dimassimo

  I was installing Solr with Jetty using these instructions. Basically, those instructions made you download the Jetty startup script and copy it to /etc/init.d/jetty. But it was not working. Each time I was starting Jetty, I had a "FAILED" message and nothing to understand why it was happening. I decided to open up the /etc/init.d/jetty script to understand what was happening. I saw that this script was using start-stop-daemon to launch jetty. After a couple of time of debugging, I discovered that removing the --daemon option at the end of the start-stop-daemon call was fixing my problem. I did a couple of research and discovered that this guy had the same problem and resolved it like I did: my removing the --daemon option. What is weird is that the switch does not seem to be specific to start-stop-daemon, because it is not documented in the man page. Also, I've seen it used for other commands. So what is that --daemon option doing? And why removing it resolved my problem? Note that I am working on Ubuntu 10.04.2 LTS.

  Read the article

• Subversion COPY/MOVE - File not found: transaction 'XXX-XX'

  - by theplatz

  I'm attempting to create a branch in one of my subversion repositories and keep running into an error. No mater what is done, I keep getting the following: File not found: transaction '3062-2e6', path '/Software/XXXXXX/branches/testbranch' I've noticed that the first part of the '3063-3e6' in the above message is the last successful committed revision in the repository. My apache logs don't give much more information: [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Could not MOVE/COPY /svn/p070361/!svn/bc/3049/Software/SXXXXXX/trunk. [404, #0] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Unable to make a filesystem copy. [404, #160013] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] File not found: transaction '3059-2e2', path '/Software/XXXXXX/branches/testbranch' [404, #160013] This is all happening on a server with an nginx frontend that proxies to Apache for the subversion bits. Other repositories are able to branch fine and I was able to create the branch using file:/// from the command line on the server this is occurring on. The permissions on this repository match every other repository and disk space is not an issue.

  Read the article

• pam_ldap.so before pam_unix.so? Is it ever possible?

  - by user1075993

  we have a couple of servers with PAM+LDAP. The configuration is standard (see http://arthurdejong.org/nss-pam-ldapd/setup or http://wiki.debian.org/LDAP/PAM). For example, /etc/pam.d/common-auth contains: auth sufficient pam_unix.so nullok_secure auth requisite pam_succeed_if.so uid >= 1000 quiet auth sufficient pam_ldap.so use_first_pass auth requiered pam_deny.so And, of course, it works for both ldap and local users. But every login goes first to pam_unix.so, fails, and only then tries pam_ldap.so successfully. As a result, we have a well-known failure message for every single ldap user login: pam_unix(<some_service>:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=<some_host> user=<some_user> I have up to 60000 of such log messages per day and I want to change the configuration so, that PAM will try ldap authentication first, and only if it fails - try pam_unix.so (I think it can improve the i/o performance of the server). But if I change common-auth to the following: auth sufficient pam_ldap.so use_first_pass auth sufficient pam_unix.so nullok_secure auth requiered pam_deny.so Then I simply can't login anymore with local (non-ldap) user (e.g., via ssh). Does somebody knows the right configuration? Why Debian and nss-pam-ldapd have pam_unix.so at first by default? Is there really no way to change it? Thank you in advance. P.S. I don't want to disable logs, but want to set ldap authentication on the first place.

  Read the article

• Why does windows (file) explorer try to connect to port 80 (http) instead just using smb?

  - by Erik

  Background: On an almost freshly installed pc I get a message along the lines of : "windows cannot find some-file-server-name. Check the spelling and try again"... when trying to access any fileshare. Troubleshooting so far: pinging works. Both by ip and by name the almost identical pc next to this one can access the file server everyone else can access the file server the pc in question can not access other open fileshares but it can connect to the internet And now for what I think is the interesting part: running wireshark with ip.addr == local.ip.add.ress and ip.addr == server.ip.add.ress tells me that it tries to connect over http. the server replies but after a few messages back and forth it stops the other machine of course just uses smb I guess port 80 just means it defaults to webdav, but I haven't been able to find anything that can cause this. Googling it the closest thing I found was this http://www.techrepublic.com/article/get-vista-and-samba-to-work/6353849 but then again this was an XP pc and I wasn't able to connect to other native Windows shares (and I tried the solution anyway and it didn't work.)

  Read the article

• How can I make AdobePS recognize my printer in Win98se?

  - by Jeff

  I am trying to use the adobe product: "PostScript Printer Driver AdobePS 4.2.6 for Windows 95 and Windows 98" to connect a new HP laser printer (CP1025nw) via USB to a machine running win98SE. I am using the PPD file for "HP color LaserJet PS". The Adobe utility installs the printer, and it shows up on the printer list ... but it doesn't print. I get an error message (sometimes) that an error occurred writing to USB001.. Evidently, AdobePS cannot "See" the printer. I suspect there is a problem wrt the printer port. Nothing I pick works. I have two virtual printer ports, USB001 and USB002 which were created during the installation of an HP inkjet printer. The inkjet will work on either of these, but the laser printer works on neither. When I connect the laserjet printer, the windows New Hardware Wizard activates, but I don't see how to point it at the AdobePS Postscript driver. HP has no support whatsoever for win98, so there's no hope of getting help from them. The printer works great with the several winXP computers connected through either the network connection or the USB. So, how do I convince Win98se to use the adobe postscript printer driver? Is this printer even a postscript printer? Is there a better way to get win98se to talk to this printer? Any suggestions?

  Read the article

• What Logs / Process Stats to monitor on a Ubuntu FTP server?

  - by Adam Salkin

  I am administering a server with Ubuntu Server which is running pureFTP. So far all is well, but I would like to know what I should be monitoring so that I can spot any potential stability and security issues. I'm not looking for sophisticated software, more an idea of what logs and process statistics are most useful for checking on the health of the system. I'm thinking that I can look at various parameters output from the "ps" command and compare to see if I have things like memory leaks. But I would like to know what experienced admins do. Also, how do I do a disk check so that when I reboot, I don't get a message saying something like "disk not checked for x days, forcing check" which delays the reboot? I assume there is command that I can run as a cron job late at night. How often should it be run? What things should I be looking at to spot intrusion attempts? The only shell access is SSH on a non-standard port through UFW firewall, and I regularly do a grep on auth.log for "Fail" or "Invalid". Is there anything else I should look at? I was logging the firewall (UFW) but I have very few open ports (FTP and SSH on a non standard port) so looking at lists of IP's that have been blocked did not seem useful. Many thanks

  Read the article

• Default sending all mails from the one account on Outlook 2007

  - by user45774

  I have two email accounts configured on my outlook 2007. One account is connecting to my exchange server which is the default I have another account connecting to my gmail. I want to by default send or reply all the emails that I receive on my gmail account through my exchange server account only. When I try replying to the email that I receive from the gmail account it gets defaulted to the same (gmail account). I need to manually change it to exchange server account. I want that to be changed to exchange server account by default for all the mails that I send or reply to. I don't want to do the manual process mentioned below in steps: Step 1: In the message window, click Account. Step 2: Click the account that you want to use. Is there a way to set the exchange server account for sending and replying to all emails on outlook irrespective of the number of accounts that I have on outlook. I have my outlook installed on a windows 2003 server.

  Read the article

• Same script, different behavior [migrated]

  - by Antoine_935

  I just stumbled upon an interesting bug... Still trying to figure out what is exactly happening. Maybe you can help. First, the context. I'm currently building yet another man to html converter (for some reasons I won't motivate here, but I need it). So, have a look at the screenshot below (see the link), more precisely at the outlined spots. See? On the upper shell, I have &lt ; and &gt ;, that is, escaped html. While on the shell below I have < and directly. But as you can see (or do I seriously need looking glass ?), the command man 2 semget | webmanneris the same on both sides, as is the which webmanner. The two are executed roughly at the same moment, with no modification made to the script between. [Oops, cannot post pictures just yet... Here comes the link] http://aspyct.org/media/webmanner-bug.png But the shell below is older (open about 1 hour ago). Newer shells all print out &lt ;. So my first guess was that it somehow had a cached reference to the old inode of the file, or old blocks or whatever. So I modified parts of the script, at the start and then at the end, to print different messages. And, surprise, the message shown up on both terminals. But still, same difference between &lt ; and <. I'm confused... How to explain that behavior? I'm working on a OSX 10.8 (Mountain Lion) EDIT: OK, there is one big difference: the shell below uses ruby 1.9.3, while above is 1.8.7. Is there any known difference in string handling between the two versions ?

  Read the article

• .htaccess with addondomain and https ssl

  - by admon

  I have main domain and addon domain. Question. 1)When surfing to: ftp.addondomain.com or mail.addondomain.com For some reason it goes to the main domain. (normally this should not be problem but i still want completely separation) Do you know the syntax to redirect in the .htaccess file this: (.*).addondomain.com - addondomain.com and where do i put the code? in the addondomain .htaccess or in the main domain attaccess I.E any_words.addondomain.com should be forwarded to the addondomain.com so these: dsdhf.addondomain.com ftp.addondomain.com mail.addondomain.com ... all will be forwarded to: addondomain.com (i.e without the prefix). 2)Same question for https:// Main domain has SSL addon domain does not have ssl. For some reason when surfing to: https:// addondomain.com you get to: http:// maindomain.com (the address bar shows https:// addondomain.com but the site pages - the page you see is the page of the main domain) I would like that if user surfs to https:// addondomain.com then (since there is no ssl for the addon domain) then user will get to: http:// addondomain.com Or alternatively user will get error message. I do not want him to be redirected to the main domain. Please if you can, write me what to add to the .htaccess and i will add it. Please also let me know where to write the code. I.E in the addondomain .htaccess or in the main domain attaccess Thanks.

  Read the article

• Svchost.exe connecting to different IPs with remote port 445

  - by Coll911

  Im using Windows XP Professional SP2. Whenever I start my Windows, svchost.exe starts connecting to all the possible IPs on LAN like from 192.168.1.2 to 192.168.1.200. The local port ranges from 1000-1099 and the remote port being 445. After it's done with the local IPs, it starts connecting to other random IPs. I tried blocking connections to the port 445 using the local security polices but it didn't work. Is there any possible way I could prevent svchost from connecting to these IPs without involving any firewall installed? My PC slows down due to the load. I scanned my PC with MalwareBytes and found out it was infected with a worm, it's deleted now but still svchost is connecting to the IPs. I also found out that in my Windows Firewall settings, under Internet Control Message Protocol (ICMP), there's a tick on "allow incoming echo request" (usually disabled) which is locked and I can't disable it. Its description is as follows Messages sent to this computer will be repeated back to the sender. This is used for trouble shooting for e.g to ping a machine. Requests of this type are automatically allowed if TCP port 445 is enabled. Any solutions? I can't bear going with the reinstalling Windows phase again.

  Read the article

• Sound doesn't work anymore after replacing RAM

  - by thejh

  Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

  Read the article

• If I ssh to a domain provided by dyndns, does my password go through them?

  - by D Connors

  I'm running Ubuntu on my work PC, and my work place provides me with a static IP address but not with a domain. It's sometimes useful for me to connect to that PC through ssh, but it's not common enough for me to instantly remember the IP number. So I set um a dyndns account, and associated a short and intuitive domain name to that IP. Here's my question, when I try to ssh to the domain, it asks me $ ssh [email protected] The authenticity of host 'something.there.foo (xx.xx.xx.xx)' can't be established. RSA key fingerprint is 'ALPHANUMERIC STRING' Are you sure you want to continue connecting (yes/no)? That surprised me a little bit. I have already registered the RSA fingerprint by connecting directly to the IP address. I thought the domain name was simply a convenient way of pointing me in the right direction (i. e. the ip address), but that message makes me think my data is actually going through their servers or something. Which one is it? Am I sending my password through someone else's server? Or is ssh just really really careful, thus warning me even if the final destination is a know host? The ssh server I'm using is the openssh-server package.

  Read the article

• sql server uninstallation issue

  - by angel

  I'm unable to remove SQL Server 2008 sp1 completely from my system. I'm using windows 7 ultimate. Everytime I try uninstalling it i get the following error. How can I remove it? here is the log: Overall summary: Final result: Failed: see details below Exit code (Decimal): -2068643839 Exit facility code: 1203 Exit error code: 1 Exit message: Failed: see details below Start time: 2013-06-24 21:10:38 End time: 2013-06-24 21:21:17 Requested action: Uninstall Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\sql_rs_Cpu64_1.log Exception help link: http://go.microsoft.com/fwlink?LinkId=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.0.1600.22 Machine Properties: Machine name: ABHI-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: United States OS language: English (United States) OS architecture: x64 Process architecture: 64 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Sql Server 2008 MSSQLSERVER MSRS10.MSSQLSERVER Reporting Services 1033 Enterprise Edition 10.0.1600.22 No Sql Server 2008 Management Tools - Basic 10.0.1600.22 No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation edition: ENTERPRISE User Input Settings: ACTION: Uninstall CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini FEATURES: RS,SSMS,SNAC_SDK,CE_RUNTIME,CE_TOOLS,SNAC HELP: False INDICATEPROGRESS: False INSTANCEID: INSTANCENAME: MSSQLSERVER MEDIASOURCE: QUIET: False QUIETSIMPLE: False X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini Detailed results: Feature: SQL Client Connectivity Status: Skipped MSI status: Passed Configuration status: Passed Feature: SQL Client Connectivity SDK Status: Skipped MSI status: Passed Configuration status: Passed Feature: Reporting Services Status: Failed: see logs for details MSI status: Passed Configuration status: Failed: see details below Configuration error code: 0xFFD65603 Configuration error description: Input string was not in a correct format. Configuration log: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\Detail.txt Feature: SQL Compact Edition Tools Status: Passed MSI status: Passed Configuration status: Passed Feature: SQL Compact Edition Runtime Status: Skipped MSI status: Passed Configuration status: Passed Feature: Management Tools - Basic Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\SystemConfigurationCheck_Report.htm

  Read the article

• Using an environment variable set to a path value: the system cannot find the path specified for %OPENCV_DIR%

  - by dumbledad

  I'm trying to set an environment variable to point to the directory into which I have extracted the latest version of OpenCV, following the instructions in OpenCV's Installation in Windows tutorial. Here's my elevated command line listing. C:\>cd C:\OpenCV2.4.6\build\x64\vc11 C:\OpenCV2.4.6\build\x64\vc11>cd ../../../.. C:\>setx -m OPENCV_DIR C:\OpenCV2.4.6\build\x64\vc11 SUCCESS: Specified value was saved. C:\>cd %OPENCV_DIR% The system cannot find the path specified. C:\>echo %OPENCV_DIR% %OPENCV_DIR% Firstly I change directory to C:\OpenCV2.4.6\build\x64\vc11 to ensure that it exists. After that is successful I change directory back to the root of the C drive. Then I use setx to make OPENCV_DIR a system wide environment variable with value the C:\OpenCV2.4.6\build\x64\vc11 path I verified in step 1. Noting the success of setx in the previous step I now change directory using the new environment variable. But it fails with the message The system cannot find the path specified. If I try to echo the value of the OPENCV_DIR environment variable it appears not to be set. Looking in the control panel the OPENCV_DIR environment variable looks correctly set: What's wrong? Why is the variable not working? Am I evoking it incorrectly when I use it to change directory or echo its value?

  Read the article

< Previous Page | 718 719 720 721 722 723 724 725 726 727 728 729  | Next Page >