Search Results

Search found 2742 results on 110 pages for 'paypal gateway'.

Page 73/110 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

  • how to set static IP address in opensolaris

    - by pm100
    in closed solaris i knew how to do this. Edit /etc/inet/ipnodes, change /etc/defaultrouter, reboot in opensolaris there is not defaultrouter file. first thing I tried was System-admin-network switch to manual enter static address and netmask and gateway. press 'activate' "this interface cannot be activated". No error messages given. Close widget, open again. Now hangs for a minute and then closes try edit /etc/inet/ipnodes, reboot eth card not up. Network widget hangs then closes Works perfectly on DHCP

    Read the article

  • Server 2003 RAS Server Utilising High WAN Traffic

    - by Joe Sergeant
    We have Routing and Remote Access configured on Server 2003 (also our primary domain controller), allowing users to connect in remotely to access files, email, etc. With one user, the RAS Server is constantly sending data to that user's remote computer. From 9am this morning it has transferred almost 800MB. The user isn't transferring any files remotely, certainly not enough to total 800MB anyway. None of the other remote users have had this issue. We have ensured that the user in question has "Use default gateway on remote network" disabled for both IPv4 and IPv6 and we are fairly confident that Offline Files isn't trying to synchronise with the server remotely, too. My question is two-fold. Firstly, has anyone had a similar experience? Secondly, what would be the best software to discover exactly what data is being sent to the remote user?

    Read the article

  • Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

    - by ale
    I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Where is debian storing its network settings?

    - by user13743
    I have a debian machine that is supposed to have a static ip, but insists on getting its address from the DHCP server. Here's this settings file: $> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.1.99 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 Yet $> sudo /etc/init.d/networking restart Reconfiguring network interfaces...done. $> sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:e0:03:09:05:2e inet addr:192.168.1.205 Bcast:255.255.255.255 Mask:255.255.255.0 ... Where is it being told to use dhcp?

    Read the article

  • 2wire modem to linksys router

    - by Imajica666
    I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

    Read the article

  • Advice on new hardware firewall for a small company server-environment

    - by Mestika
    Hi everyone, My companies currently hardware firewall (an old ZyXEL ZyWALL firewall) and is indeed requiring an update to a new firewall. It is a small company with a similar small server-environment, so the need for a huge, complex and expensive solution isn’t there but a more “straight-forward” firewall, that can provide the necessary security to our systems and block unwanted elements from the core server and only accept access through our one server which is used as an “gateway” between the Internet and our internal network. I haven’t that much experience with hardware firewalls so I’m requesting any good advice and/or knowledge on which products will be suited for our specific need. If you need more information about the specific needs we require, please let me know and I’ll provide them to you. Sincerely - Mestika

    Read the article

  • Is there a sensible way of 'teaming' two ADSL connections?

    - by Tim Long
    I work in an office complex that has two seperate ADSL connections, which they use to provide two seperate networks (actually both the ADSL routers go into a Cisco managed switch with two VLANs, one for each ADSL connection). Circumstances have changed so that 95% of the users are all on one ADSL connection. It would be great if there were a way to join together both connections to emulate a single connection at double the speed, but the ISP doesn't support bonding. So, is there a sensible way to take two completely seperate ADSL lines and use them to provide a single internet gateway?

    Read the article

  • how to change interface ip in ifconfig with /etc/network/interfaces

    - by user2478348
    Hi everybody when modifiying /etc/network/interfaces, saving it and then executing ifconfig i can't see the modification i made..for example here is part of my /etc/network/interfaces: auto wlan1 iface wlan1 inet static address 192.168.0.60 netmask 255.255.255.0 gateway 192.168.0.61 you can see that the IP address of my wlan1 is 192.168.0.60 but when typing ifconfig i have this: wlan1 Link encap:Ethernet HWaddr 00:19:70:0f:c2:9c inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::219:70ff:fe0f:c29c/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:758 erreurs:0 :0 overruns:0 frame:0 TX packets:610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:73490 (73.4 KB) Octets transmis:127883 (127.8 KB) (the inet adr:192.168.0.1 and not 198.168.0.60)..if someone can help me I'll be very thankful :)

    Read the article

  • 13 IP addresses, how to add them to domain SPF?

    - by Willy
    Hi All, Let say I have these IP addresses on my server: 170.120.210.209 gateway 170.120.210.210 server IP 170.120.210.211 170.120.210.212 170.120.210.213 170.120.210.214 170.120.210.215 170.120.210.216 170.120.210.217 170.120.210.218 170.120.210.219 170.120.210.220 170.120.210.221 170.120.210.222 I am now willing to setup SPF record for my domain but don't want to write each IP one by one. Could you please tell me the short way of this? How can I convert these IP addresses into CIDR notation? Is this correct? 170.120.210.210/28 Thanks for your help.

    Read the article

  • Small business VPN solution

    - by Crash893
    I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

    Read the article

  • Waht are the best proxy servers for Mikrotik router?

    - by niren
    I want to setup proxy server for my Mikrotik router. There is inbuilt web-proxy for Mikrotik router but I can extend this upto transparent proxy(kind of proxy server) only. We need High anonymity proxy so that we can hide our LAN static IPs(we don't have private IP) from outside Intruder/hackers. And also I know I can setup NAT rule to hide our IP(only private IP not public/static IP) as per this link, but I cann't hide static/public IP. Essentially I want to hide our Public/Static IP (there is static/public IP for all systems in our company) from outside Internet. To achieve this I guess I need other software apart from Mikrotik router gateway setup. can anyone suggest me Is there any other software to achieve my requirement? I know about squid proxy but am not sure whether It can hide our static/public IP. Note: we have assigned public/Static IP to all systems of our company since we have rights to access our company's system from anywhere by dedicated laptop(given by our company with more security) through VPN connection.

    Read the article

  • Windows VPN not authenticating from ADSL to Wireless link

    - by deanvz
    I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

    Read the article

  • ip routes to specific interface

    - by user65053
    I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Best way to split LAN computers on two WANs (not load balancing)

    - by lpfavreau
    What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

    Read the article

  • dd-wrt switch for PfSense

    - by Kmao
    I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • How to limit access to Exchange 2003 Mobile Activesync server by user?

    - by micilin
    So I was asked to set up an Exchange Activesync mobile gateway. That's done. It's a separat eExchange 2003 front-end server configured for SSL, and I've put an off-domain ISA server in front of it. Now I'm being asked to limit which users can connect to it. By default an Exchange front-end server allows any user who has a mail account to connect to the front -end server. So I'm looking at the permissions on the various IIS sites/apps on the server, but I know that it's easy to break Exchange Front-end server perms. So I've got the following in IIS: Exadmin Exchange EchWeb Microsoft-SErver-ActiveSync MobileAdmin OMA And a couple of others that I dont think are relevant. Can I change the permissions on one of these to restrict who can connect to Activesync? As a bonus: Can I do it in a way that does not affect ordinary browser based Exchange Access? Thanks in Advance!!

    Read the article

  • Changing Internet connection on ISA Server 2000

    - by garyb32234234
    Hi We are getting a new internet connection installed and will need to unplug the old one and connect this to our ISA Server 2000. Will this be a simple swap out job? We will be given a new ip, which i know i will have to enter into the external network card TCP/IP page. I will also be given the default gateway to enter. The ISP engineer said we may have to reset the ARP? cache, if we dont know how we will have to reset the ISA server? Has anyone any experience? The current connection is with the same ISP but it was owned by the business park were we are located and they linked up an ethernet port to what i assume is their own router. Hope you can help, i know that ISA 2000 is somewhat less easy to use than the newer versions.

    Read the article

  • IIS FTP service - download timeouts and restarts getting the data twice

    - by accel229
    We have an IIS FTP site on a Windows Server 2003 x64 machine. Application Layer Gateway service is disabled (so http://support.microsoft.com/kb/931130 does not apply). Windows Firewall service is disabled as well. Connection timeout for the FTP site (there is only one) is set to 1,200 seconds = 20 minutes. An external client can connect to the site, list directory contents and download small files. When a client attempts to download a large file (eg, if the download continues for 3 minutes, which is still under 20 minutes, but relatively long), the server sends all data, then the connection times out, the client issues REST / RETR commands attempting to restart the download since after the last byte (which I believe should succeed and receive exactly 0 bytes), and the server behaves as if the client tried to restart after byte 0, that is, it sends the entire file all over. Any ideas on how to fix this?

    Read the article

  • ACER ASPIRE V3-571G-9435 Fan not kicking in leading to overclocking

    - by brythespy
    This laptop has always had this problem. The temperatures kick up to the thermal ceiling of 99C for the CPU (i7-3610QM) and 94C for the GPU (GT 640M). Problem is, the FAN doesn't give a damn. It's actually QUIETER when the temperatures are that high, than when it's at 60C or so. I figured it was a problem with the BIOS, so I updated that, no change. So maybe it was a problem with windows? Nope, same result on gaming with Ubuntu. The major problem of this, is that after gaming for ten minutes the CPU throttles itself to 1197MHz(as opposed to 3193), and the GPU goes down to 135MHz( as opposed to 843MHz). The problem is that the fan won't kick in like I know it can, because when the laptop is in POST, like at BIOS setup, the fan is like a vacuum cleaner it's so loud! I don't really care about noise, so I'd love to have the fan like that all the time as long as the temperatures don't fly through the roof... So, things I've tried so far, to avoid possible duplicate answers. Checked for dust: It's been this way since the laptop was new, and I've since then taken it apart. No dust buildup. Background stuff running?: No, problem persists across OS'es, and it happens while gaming anyways Manually underclocking both CPU/GPU: Using windows, I can force the CPU to stay at 1.1GHz, but the temperature STILL easily hits 99C after 5 min of gaming Contacted Acer support?: No help at all. They told me to update and reset the BIOS, which I have done multiple times. There are only about 6 changeable things anyway, none of which should affect the FAN control Third party fan control program?: None detect the fan So, I'm screwed until I can afford to replace this laptop, but I am very satisfied with performance in games... Whenever the CPU/GPU aren't being throttled. Anyone that can offer advice to solve this problem would be greatly appreciated. Hell, if you solved my problem I'd send you some monies through paypal.

    Read the article

  • How to enable RDP to a Server 2008 R2 on another network? VM network

    - by Saariko
    I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

    Read the article

  • Google Chrome custom search engine for secure Wikipedia

    - by gdejohn
    I have this custom search engine set up in Google Chrome: https://encrypted.google.com/search?q=site%3Aen.wikipedia.org+%s&btnI=745 It searches Google for site:en.wikipedia.org {query}, and the btnI=745 is for I'm Feeling Lucky, so it automatically redirects to the first result. I like this better than using Wikipedia's search function directly because it gives me very effective approximate string matching, so I can misspell my search, or leave a word out, or just search for some keywords, and I still get what I'm looking for right away. What I'd like is for it to use Wikipedia's secure gateway: https://secure.wikimedia.org/wikipedia/en/wiki/ It's easy enough to set up a custom search engine that uses the secure version of Wikipedia's search function directly, but I can't figure out how to correctly incorporate it into my version going through Google. Nothing I've tried works.

    Read the article

  • ipconfig /release not working, why?

    - by barlop
    ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

    Read the article

  • setting up bridged adapter for VPN server

    - by B. VB.
    I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

    Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >