floating point conversion - Page 730

Adding a Second Wireless Router to an Existing Wired Network

- by KVCrawford

I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

Read the article

Mac Grey/White Screen of Death

- by cust0s

The other night I updated my iTunes to the latest version (through Software Update) when I came to turn on my computer I was greeted with the dreaded white screen of death. I use an early 2008 iMac 24". I've tried the basic things, unplugging/turning off accessories, trying to boot from the install disk, reseting pram, etc, etc. Still no luck and no change what-so-ever. All I've been able to ascertain that my keyboard still works (by ejecting). I should point out that I did recently replace my Hard drive with a Western Digital Black 500GB (though the computer is well out of warrenty) and I'm a little concerned that the problem could be the screen. Update (18/05/10): I've been told that I could be getting the White/Grey screen of death because the optical flex cable is damaged (aparently this is common). Apparently the Optical Drive is part of the POST sequence, and an inability to read the drive can result in failure for the system to move on to other bootable volumes. More info here. I will disable the optical drive and see if that works.

Read the article

eXist-db: can't start webstart client on a closed port, reverse proxied via apache

- by rvdb

I am configuring an Apache HTTP server so it reverse proxies requests starting with /app/ to an eXist-db instance running in a Tomcat server, on port 8082. This port has been closed in the firewall and is inaccessible to the outer world. Following the eXist documentation, I have following rules in place in my httpd.conf file: ProxyPass /apps/ http://localhost:8082/ ProxyPassReverse /apps/ http://localhost:8082/ ProxyPassReverseCookiePath /apps/ / All goes well for requests to e.g. 'http://mydomain/apps/exist/index.xml'. Yet, the webstart client (accessible at 'http://localhost:8082/exist/webstart/exist.jnlp' on the web server) doesn't work behind the proxy. While 'http://mydomain/apps/exist/webstart/exist.jnlp' does generate a valid exist.jnlp file, that file can't be executed. The reason seems quite obvious: apparently, the eXist-db instance generating the exist.jnlp file only sees the proxied request as: 'http://localhost:8082/exist/webstart/exist.jnlp'. Yet, since the exist.jnlp file is executed on the client, that reference is meaningless (unless the client computer happens to have an eXist-db instance running on that port). Executing the exist.jnlp file hence fails with a 'connection refused' error. Yet, there's no problem at all connecting a local eXist-db Java client to the proxied eXist instance with the URL xmldb:exist://mydomain/apps/exist/xmlrpc. The problem lies in generating the webstart exist.jnlp file, which seems to need access to a publicly accessible URL. However, opening port 8082 and replacing the Proxy references to 'http://localhost:8082' with 'http://mydomain:8082' IMO rather destroys the point of reverse proxying. Do others have had success reverse proxying eXist-db on a closed port behind Apache? Are there perhaps some Proxy configuration settings I have overlooked (I'm no expert at all) that can make eXist see the original request instead of the proxied one? Kind regards, Ron

Read the article

Network driver for Hyper-V restore from Windows Home Server

- by Philipp Schmid

I have backed up Windows Server 2008 running virtualized on Hyper-V to a Windows Home Server 2008 SP1 (I know I should have backed up the VHD instead). Now I need to restore the contents of the VM from WHS. I have created a restore CD ISO and used it to create a new VM. It all works as advertised up to the point where the restore process wants to load the network drivers (it only finds 4 disk drivers on the restore CD. but no network drivers). So I created a virtual floppy and copied the contents of 'Home Server Drivers for Restore onto it. But no luck! I have tried moving the 4 subdirectories into the root of the floppy, but that didn't work either. Finally, I started another instance of the WS 2008 to identify the network driver that the virtualized instance is using (%WINDOWS%\system32\drivers\netvsc60.sys) and copied that file onto the virtual floppy, without success. Does anyone have any suggestions on how to get networking working on a Hyper-V instance running off the Windows Home Server Restore CD? UPDATE: As suggested by delenda, I have added a legacy network adapter to my VM, and indeed I now get a network driver listed! However, the WHS it still not found, even after entering the home server name manually. PHS

Read the article

Google-Bot fell in love with my 404-page

- by 32bitfloat

Every day my access-log looks kind of this: 66.249.78.140 - - [21/Oct/2013:14:37:00 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [21/Oct/2013:14:37:01 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [21/Oct/2013:14:37:01 +0200] "GET /vuqffxiyupdh.html HTTP/1.1" 404 1189 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" or this 66.249.78.140 - - [20/Oct/2013:09:25:29 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.75.62 - - [20/Oct/2013:09:25:30 +0200] "GET /robots.txt HTTP/1.1" 200 112 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" 66.249.78.140 - - [20/Oct/2013:09:25:30 +0200] "GET /zjtrtxnsh.html HTTP/1.1" 404 1186 "-" "Mozilla/5.0 (compatible; Googlebot/2.1; +http://www.google.com/bot.html)" The bot calls the robots.txt twice and after that tries to access a file (zjtrtxnsh.html, vuqffxiyupdh.html, ...) which cannot exist and must return a 404 error. The same procedure every day, just the unexisting html-filename changes. The content of my robots.txt: User-agent: * Disallow: /backend Sitemap: http://mysitesname.de/sitemap.xml The sitemap.xml is readable and valid, so there seems to be no reason why the bot should want to force a 404-error. How should I interpret this behaviour? Does it point to a mistake I've done or should I ignore it?

Read the article

Throughput; capacity planning help for C10K like design

- by z8000

I am designing a network service in which clients connect and stay connected -- the model is not far off from IRC less the s2s connections. I could use some help understanding how to do capacity planning, in particular with the system resource costs associated with handling messages from/to clients. There's an article that tried to get 1 million clients connected to the same server [1]. Of course, most of these clients were completely idle in the test. If the clients sent a message every 5 seconds or so the system would surely be brought to its knees. But... How do you do less hand-waving and you know, measure such a breaking point? We're talking about messages being sent by a client over a TCP socket, into the kernel, and read by an application. The data is shuffled around in memory from one buffer to another. Do I need to consider memory throughput ("5 GT/s" [2], etc.)? I'm pretty sure I have the ability to measure the basic memory requirements due to TCP/IP buffers, expected bandwidth, and CPU resources required to process messages. I'm a little dim on what I'm calling "thoughput". Help! Also, does anyone really do this? Or, do most people sort of hand-wave and see what the real world offers, and then react appropriately? [1] http://www.metabrew.com/article/a-million-user-comet-application-with-mochiweb-part-3/ [2] http://en.wikipedia.org/wiki/GT/s

Read the article

windows clients cannot get dns resolution until you open and close ipv4 properties page

- by GC78

This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

Read the article

Apache2 - Hosting two sites on the same domain with different ports

- by user1026361

I am hosting a staging site (test.mydomain.com) which currently work well on port 80 for two sites (test.mydomain.com and test.FRmydomain.com) I am working on a new backend and I would like to deploy a third site on this server for testing. My hope is that it will live at test.mydomain.com:4204. I've got some experience with apache and quickly added statements: Listen 4204 NameVirtualHost *:4204 and created a new config for my site. What I imagine are the relevant parts of my config: <VirtualHost *:4204 > ServerAdmin [email protected] ServerName test.mydomain.com:4204 However, the site is not publicly available, by name or ip. If i curl localhost:4204 from the server, I get the expected page content At this point, I'm a bit of a loss on how to go forwards. It seems like my config is correct but not available to be served. Am I better off defining a proxy definition so that, for instance: test.mydomain.com/4204 proxies to my localhost server or is there a way to make the site available via the internet? EDIT: I have added an iptable rule after further Googling with the command: iptables -I INPUT -p tcp --dport 4204 -j ACCEPT I can see apache listening on 4204 and the rule is definitely in place but cant reach the site

Read the article

Sun T5120: Memory issue with 8GB DIMMs, "Unsupported memory configuration"

- by watain

Read the article

Windows XP error message: "Windows cannot find 'explorer.exe'"

- by Meysam

In Windows XP I can open "My Computer" and see all the hard drives. I can also see the explorer.exe process running among other processes in Task Manager. But after opening "My Computer", when I double click on one of the drives to open it, I get the following error message: Windows cannot find 'explorer.exe'. Make sure you typed the name correctly, and then try again. To search for a file, click the start button, and then click search. Although I could detect and remove several suspicious files using Malwarebytes & Microsoft Security Essentials, the problem still remains. The interesting point is that if I right click on one folder and select Open or Explore from the menu bar, I can open the folder! but if I double click on the folder, it does not open and I get the above error message. How can I fix this problem? Any advice would be appreciated! Update: I formatted the C: drive (NTFS), a deep format, and installed a fresh Windows XP on it. I am not getting this error when I double click on C drive icon anymore. But the same error appears when I double click on other drive names. Maybe I should format them too!

Read the article

Linux Tuning for High Traffic JBoss Server with LDAP Binds

- by Levi Stanley

I'm configuring a high traffic Linux server (RedHat) and running into a limit I haven't been able to track down. I need to be able to handle sustained 300 requests per second throughput using Nginx and JBoss. The point of this server is to run checks on a user's account when that user signs in. Each request goes through Nginx to JBoss (specifically Torquebox with JBoss A7 with a Sinatra app) and then makes an LDAP request to bind that user and retrieve several attributes. It is during the bind that these errors occur. I'm able to reproduce this going directly to JBoss, so that rules out Nginx at least. I get a variety of error messages, though oddly JBoss stopped writing to the log file recently. It used to report errors about creating native threads. Now I just see "java.net.SocketException: Connection reset" and "org.apache.http.conn.HttpHostConnectException: Connection to http://my.awesome.server:8080 refused" as responses in jmeter. To the best of my knowledge, I have plenty of available file handles, processes, sockets, and ports, yet the issue persists. Unfortunately, I have very little experience tuning servers. I've found a couple useful documents - Ipsysctl tutorial 1.0.4 and Linux Tuning - but those documents are a bit over my head (and just entering the the configuration described in Linux Tuning doesn't fix my issue. Here are the configuration changes I've tried (webproxy is the user that runs Nginx and JBoss): /etc/security/limits.conf webproxy soft nofile 65536 webproxy hard nofile 65536 webproxy soft nproc 65536 webproxy hard nproc 65536 root soft nofile 65536 root hard nofile 65536 root soft nproc 65536 root hard nofile 65536 First attempt /etc/sysctl.conf sysctl net.core.somaxconn = 8192 sysctl net.ipv4.ip_local_port_range = 32768 65535 sysctl net.ipv4.tcp_fin_timeout = 15 sysctl net.ipv4.tcp_keepalive_time = 1800 sysctl net.ipv4.tcp_keepalive_intvl = 35 sysctl net.ipv4.tcp_tw_recycle = 1 sysctl net.ipv4.tcp_tw_reuse = 1 Second attempt /etc/sysctl.conf net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 net.core.netdev_max_backlog = 30000 net.ipv4.tcp_congestion_control=htcp net.ipv4.tcp_mtu_probing=1 Any ideas what might be happening here? Or better yet, are there some good documentation resources designed for beginners?

Read the article

How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface?

- by JJarava

This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

Read the article

Why do I get a DegradedArray event with mdadm

- by azera

Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

Read the article

How to serve Rails application with Passenger/Apache without domain name?

- by grifaton

I am trying to serve a Rails application using Passenger and Apache on a Ubuntu server. The Passenger installation instructions say I should add the following to my Apache configuration file - I assume this is /etc/apache2/httpd.conf. <VirtualHost *:80> ServerName www.yourhost.com DocumentRoot /somewhere/public # <-- be sure to point to 'public'! <Directory /somewhere/public> AllowOverride all # <-- relax Apache security settings Options -MultiViews # <-- MultiViews must be turned off </Directory> </VirtualHost> However, I do not yet have a domain pointing at my server, so I'm not sure what I should put for the ServerName parameter. I have tried the IP address, but when I do that, restarting Apache gives apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sun Jan 17 12:49:26 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sun Jan 17 12:49:36 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results and pointing the browser at the IP address gives a 500 Internal Server Error. The closest I have got to something sensible is with <VirtualHost efate:80> ServerName efate DocumentRoot /root/jpf/public <Directory /root/jpf/public> AllowOverride all Options -MultiViews </Directory> </VirtualHost> where "efate" is my server's host name. But now pointing my browser at the server's IP address just gives a page saying "It works!" - presumably this is a default page, but I'm not sure where this is being served from. I might be wrong in thinking that the reason I have been unable to get this to work is related to not having a domain name. This is the first time I have used Apache directly - any help would be most gratefully received!

Read the article

IIS FTP 7.5 Data Channel Problem (SSL)

- by user59050

Hey there I wonder if anyone can get me in the right direction. I am setting up both a FTPS Client and Server, FTPS Server using Microsoft’s iis FTP 7.5. On the client side it will be running on Linux and I am using M2crypto for the openssl wrapping (python). I am worried the problem is on the server side (iis7.5) due to the following discovery : If I host using Filezilla with BOTH the control and data channel being forced to be encrypted it works 100% (100% file transmission), if i use iis as the server everything works up to the point when the data channel takes over... i.e. all data of the retrieved file is already received correctly in my basket! The ftp server just won't send the final '226 Transfer complete.' on the cmd socket. Why? If i force the client or server to close the connection the file is 100% intact....If i use iis 7.5 with forced encryption on control channel all works 100% as long as i don’t force data channel... Here are some screenshots to demo this... Client View after Kill Client : pics @ http://forums.iis.net/p/1172936/1960994.aspx#1960994 Summary : We can establish the connection, do directory listings, start the upload, see the file (0bytes) created on the server but then the client hangs. If we terminate the client, the uploaded file on the server suddenly jumps up to full size.

Read the article

AWS Linux EC2: yum won't run with plugins

- by Patrick

Short Version: yum commands on my Amazon Linux EC2 AMI only work with --noplugins. Long Version: A couple of days ago, I ran yum update at the behest of the SSH Login MoTD telling me I had updates to install. About midway through the update (specifically while updating the kernel), the update abruptly ended (79 of 138 items completed). The website I host on EC2 got weird for a few minutes, but eventually seemed to stabilize back out (maybe EC2 restarted itself?), and I didn't have further issues (other than MySQL started running out of memory, but I think that's probably unrelated to this). Today, I went to install gcc-c++ (with yum install gcc-c++). When I did, I got the following message: Loaded plugins: priorities, security, update-motd, upgrade-helper Config error: Command "updateinfo" already defined and I get that for any command I can think to run using yum. However, If I throw in the --noplugins flag, then magically it seems to work. To be clear, when I installed a different package a week ago, it worked totally correctly, so the yum update is the only thing I can think of that changed. I could find nothing on Google with regard to "updateinfo" already defined (with and without quotes). I tried running yum update --noplugins which spit out a message telling me that I should have run yum-complete-transaction instead, but proceeded to try to update something on its own. When that completed, I tried yum-complete-transaction but that gave me a message about the transactions not lining up correctly, so it removed the old transaction (Probably since I should have completed the first transaction before trying to update again, if I had known). Based on the SF question "Linux EC2 Broken Yum", I've also tried yum clean all --noplugins (fails the same with plugins) which just gives me Cleaning repos: amzn-main amzn-updates rpmforge Cleaning up everything I also tried package-cleanup --problems Loaded plugins: priorities, update-motd, upgrade-helper No Problems Found and package-cleanup --dupes Gives a lot of dupes, so I pasted them here: http://pastebin.com/VVFQEkTT instead of inline. At this point, I'm not sure what else there even is to check.

Read the article

How to set up multiple SSIDs with bandwidth limiting on a single wireless router?

- by Rahul Narain

I have an Asus WL-520GU wireless router connected to a cable modem that I use for wireless internet access in my apartment. I would like to set it up so that it provides two SSIDs: one secured and password-protected for my regular use, and a "guest" SSID that's unsecured but throttled to, say, 10% of the available bandwidth. What is the most straightforward way to do this? I've been looking into DD-WRT and Tomato, both of which support my router. DD-WRT supports setting up multiple SSIDs using the GUI, but I don't know if it's possible to limit the bandwidth of each SSID independently; point #12 in this FAQ thread says it's not possible to limit by day or by MAC address, which is discouraging but not conclusive. Tomato allows bandwidth limits in its QoS settings, going by the screenshot here, but multiple SSID support is still experimental and it doesn't look like it will work with the encryption settings or bandwidth limits in the GUI. I'd like to know a good way to do this which gives me the fewest opportunities for screwing up. I'm no stranger to the command line, if that turns out to be what's necessary, but if so, please explain what the commands are doing because I don't have a good mental model of what needs to happen to set this up.

Read the article

Windows server 2008, Dns. I'm confused

- by Dejan.S

Hi. I recently setup a window server 2008 server at work. Keep in mind I have never worked with it before:). Background story is I try to host a couple of sites on the server through iis7, I got domains (currently hosted at other hosters for the moment). I want to point the domain NS to my server on all of them. I have read how to setup a DNS on the server, so far so good. now my dns is companyname.com in the server manager I got DNS / companyname.com in there I got ns.comanyname.com, in there I got Host(A) with the server ip now this is where I get confused about how things work with DNS, NS & Host(A). I dont know how to assign(so to speak) the Host(A) to one of my webapps hosted on the iis7, because that is the pointer right?. To leave an example to work with lets say, Hosted.com is hosted on my iis7, on port 81. You don't understand how great full I would be if somebody could explain this confusion. EDIT: Do I need to create a DNS for every site hosted on my server? Or just make a A Host/Record? Thanks guys

Read the article

3 Servers, is this is a cluster?

- by Andy Barlow

Hello, At the moment I have one Ubuntu server, 9.10, running with a simple Samba share, a mail server, DNS server and DHCP server. Mostly its just there for file sharing and email server. I also have 2 other servers that are exactly the same hardware and spec as the first, which have an rsync set up to retrieve the shared folders and backs them up. However, if the first server goes down, all of our shares disappear along with our mail and the system must be rebuilt. Also I tend to find if people are downloading a large amount from the file server, no-one can access there emails - especially in the morning when everyone is signing in at once. Would it be more beneficial for me to have all 3 servers, all running the same services, doing the same thing with some sort of cluster with load balancing? I'm not really sure where to begin looking, or how to go about such a setup where 3 servers are all identical, but perhaps one acts as the main load balancer?? If someone can point me in the right direction, or if this simply sounds like one of those Enterprise Cloud's that is now a default setup in Ubuntu Server 9.10+, then I'll go down that route. Cheers in advance. Andy

Read the article

A star vs internet routing pathfinding

- by alan2here

In many respects pathfinding algorythms like A star for finding the shortest route though graphs are similar to the pathfinding on the internet when routing trafic. However the pathfinding routers perform seem to have remarkable properties. As I understand it: It's very perfromant. New nodes can be added at any time that use a free address from a finite (not tree like) address space. It's real routing, like A*, theres never any doubling back for example. IP addresses don't have to be geographicly nearby. The network reacts quickly to changes to the networks shape, for example if a line is down. Routers share information and it takes time for new IP's to be registered everywhere, but presumably every router dosn't have to store a list of all the addresses each of it's directions leads most directly to. I can't find this information elsewhere however I don't know where to look or what search tearms to use. I'm looking for a basic, general, high level description to the algorithms workings, from the point of view of an individual router.

Read the article

How to manage mounted partitions (fstab + mount points) from puppet

- by Cristian Ciupitu

I want to manage the mounted partitions from puppet which includes both modifying /etc/fstab and creating the directories used as mount points. The mount resource type updates fstab just fine, but using file for creating the mount points is bit tricky. For example, by default the owner of the directory is root and if the root (/) of the mounted partition has another owner, puppet will try to change it and I don't want this. I know that I can set the owner of that directory, but why should I care what's on the mounted partition? All I want to do is mount it. Is there a way to make puppet not to care about the permissions of the directory used as the mount point? This is what I'm using right now: define extra_mount_point( $device, $location = "/mnt", $fstype = "xfs", $owner = "root", $group = "root", $mode = 0755, $seltype = "public_content_t" $options = "ro,relatime,nosuid,nodev,noexec", ) { file { "${location}/${name}": ensure => directory, owner => "${owner}", group => "${group}", mode => $mode, seltype => "${seltype}", } mount { "${location}/${name}": atboot => true, ensure => mounted, device => "${device}", fstype => "${fstype}", options => "${options}", dump => 0, pass => 2, require => File["${location}/${name}"], } } extra_mount_point { "sda3": device => "/dev/sda3", fstype => "xfs", owner => "ciupicri", group => "ciupicri", $options = "relatime,nosuid,nodev,noexec", } In case it matters, I'm using puppet-0.25.4-1.fc13.noarch.rpm and puppet-server-0.25.4-1.fc13.noarch.rpm.

Read the article

Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

- by ThaKidd

As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

Read the article

BSOD during Cygwin install

- by Mike Pennington

I have been running Cygwin (1.7.7) under Windows Vista 64-bit, SP2 for at least a year, and had no problems with my installation at all until today. When I tried to install apt-cyg, I realized that I needed to get the svn client. During the installation of the package dependencies, Vista threw a blue screen of death. I hoped this was a one-time occurrence, so I rebooted into Vista and tried to install svn again; same result. Next I completely removed Cygwin's directory, and all Cygwin registry entries; at this point, I tried reinstalling the base Cygwin system again. During the installation of bash, I got another BSOD: Apologies for the fuzzy pic, I had to shoot with my phone camera. I googled for BSOD and Cygwin and found a post by Dave Korn mentioning that the only reasons Cygwin should cause a BSOD is because of either ioperm.sys or some USB utilities. I have neither on my system. Every time I have tried reinstalling, Vista BSODs; I have not had problems installing any other software packages on this Vista machine. How can I get Cygwin installed again (without reinstalling Vista)?

Read the article

Redirect specific domains with DNS

- by user66377

Currently we filter internet content using OpenDNS, our internal Windows DC/DNS servers point to the router's DNS, which then points to the OpenDNS servers. This works well to block all computer's on the network equally. New issue. We now need to separate what computers can go to what sites. So facebook is blocked for everyone right now, but I need to open it up to the 3 community computers now. The 3 community computers will be on an untrusted network seperate from the company computers so they can have their own DNS server, from their own router. The issue is though they still must connect to the internet using the same IP address. So OpenDNS sees the same IP and blocks them the same way. We are looking into getting a second IP, but it's not likely an option without going up to the next major level with our ISP which we don't want to do. My thought is this. Can I setup a DNS server on the untrusted network, and then depending on the request that comes in, have it send it to either OpenDNS or our ISP's DNS? Example www.facebook.com and www.youtube.com are both on the OpenDNS blacklist. So if they go to www.youtube.com, the local DNS server goes to the ISP's DNS to get the IP and thus the client gets the right IP and can go to the site. This would be manually entered for each allowed site thus creating a white list. Then if they go to www.facebook.com, since the local DNS server does not find an entry, it sends the request to OpenDNS, which then sees the site is on the blacklist, and thus sends the it's blocked webpage. The local DNS server can be either Bind on Linux or MS DNS on Window 2008. If this can be done, can you give some direction as well as I've never setup a DNS such as this before. Thanks

Read the article

Local DNS and Apache Server Configuration Interferring - example.com / www.example.com

- by nicorellius

I have a domain for my site: example.com I am also running local DNS with these lines: www IN CNAME server.<host_provider>.com. dev IN CNAME server.<host_provider>.com. So www.example.com and dev.example.com go to production and development sites, respectively, that are hosted by a host company. In my Apache configuration for the main site, I'm running a rewrite rule like this: RewriteEngine ON RewriteCond %{HTTP_HOST} ^example\.com$|!dev\.example\.com$ [NC] RewriteRule ^(.*)$ http://www\.%{HTTP_HOST}/$1 [R=302,L,NE] This rule seems to work, as when you are off the network and go to example.com in the browser, you get redirected to www.example.com. The problem is when I'm on the network, and I go to example.com I get an error page, saying page can't be found. No server errors; just a page can't be found, as if the local DNS is causing it to stop looking at that point. I'm also using Nettica for DNS service and have this A record in place: example.com Host (A) Default xxx.xx.xxx.xx This handles the external DNS, but my problem seems to be related to my internal DNS. For example, inside my network, I can go to servers on the network with addresses like this: server.example.com server1.example.com server2.example.com These are configured in my local DNS. I'm just not sure how to get past the "empty" subdomain and go to example.com. Adding to this since it might not be clear. If I'm out side the example.com network, on another network, like example123.com, then when I go to example.com I'm redirected to www.example.com as expected, eg, the Apache rewrite rule is working. Thanks in advance for any information.

Search Results

Search found 24734 results on 990 pages for 'floating point conversion'.

Page 730/990 | < Previous Page | 726 727 728 729 730 731 732 733 734 735 736 737 | Next Page >

- by KVCrawford

- by cust0s

- by rvdb

- by Philipp Schmid

- by 32bitfloat

- by z8000

- by GC78

- by user1026361

- by watain

- by Meysam

- by Levi Stanley

- by JJarava

- by azera

- by grifaton

- by user59050

- by Patrick

- by Rahul Narain

- by Dejan.S

- by Andy Barlow

- by alan2here

- by Cristian Ciupitu

- by ThaKidd

- by Mike Pennington

- by user66377

- by nicorellius

< Previous Page | 726 727 728 729 730 731 732 733 734 735 736 737 | Next Page >