Search Results

Search found 22078 results on 884 pages for 'composite primary key'.

Page 732/884 | < Previous Page | 728 729 730 731 732 733 734 735 736 737 738 739  | Next Page >

• Troubleshooting unwanted NTP Traffic

  - by Jaxaeon

  A domain controller running Windows Server 2012 is sending NTP and NETBIOS traffic to an address that has never been configured as a time provider. The server logs give no indication that any NTP traffic is failing. The only place I see any evidence of this traffic is in pfSense system logs: (Blocked) Jun 9 08:48:50 DOMAIN 10.0.1.100:123 192.128.127.254:123 UDP (Blocked) Jun 9 08:48:53 DOMAIN 10.0.1.100:137 192.128.127.254:137 UDP As far as I can tell the NTP service is working normally otherwise: DC2.domain.com[10.0.1.101:123]: ICMP: 0ms delay NTP: -0.0131705s offset from DC1.domain.com RefID: DC1.domain.com [10.0.1.100] Stratum: 3 DC1.domain.com *** PDC ***[10.0.1.100:123]: ICMP: 0ms delay NTP: +0.0000000s offset from DC1.domain.com RefID: clock1.albyny.inoc.net [64.246.132.14] Stratum: 2 The time provider NtpClient is currently receiving valid time data from 1.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->204.2.134.163:123). The time provider NtpClient is currently receiving valid time data from 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). The time service is now synchronizing the system time with the time source 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). I've been inside and out of the NTP configuration and cannot find any reason for this traffic. Reverse DNS points the destination address to nothing.attdns.com. pinging nothing.attdns.com from the domain controller in question leads to a response from loopback (127.0.0.2) which makes my head hurt. Any ideas? EDIT1: It should probably be noted that after a dns flush, nslookup 192.128.127.254 returns nothing.attdns.com. 192.128.127.254 is not present in domain.com DNS records. The attdns.com domain is not present in cached lookups. 127.in-addr.arpa is clean of any funkyness. EDIT2: The loopback ping response from nothing.attdns.com is possibly unrelated. Machines on other networks are also displaying this behavior. EDIT3: As mentioned in the comments, I tracked the problem network adapter back to my pfSense VM hosted in esxi 5.5 (I know shame on me for virtualizing a firewall). pfSense was configured to use DC1.domain.com as its primary time provider, but upon changing it back to pool.ntp.org the problem persists. pfSense logs give no indication of NTP misconfiguration. Everywhere I can think to look this VM is identified as 10.0.1.253, so I still have no idea why it’s sending NTP requests as 192.128… Since this firewall was a temporary solution to a problem that no longer exists so I am going to decommission it. EDIT4: The queries were coming from another machine sharing the same virtual adapter as the firewall. The machine has two local adapters: one for LAN, and the other for attached hardware that uses an Ethernet connection. That hardware sits in the the mystery subnet, and the machine is broadcasting NTP requests over both adapters.

  Read the article

• How to rewrite these URLs?

  - by Evik James

  I am brand new to URL rewriting. I am using an Apache rewriting module on IIS 7.5 (I think). Either way, I am able to do rewrites successfully, but am having trouble on a few key things. I want this pretty url to rewrite to the this ugly url: mydomain.com/bike/1234 (pretty) mydomain.com/index.cfm?Section=Bike&BikeID=1234 (ugly) This works great with this rule: RewriteRule ^bike/([0-9]+)$ /index.cfm?Section=Bike&BikeID$1 Issue #1 I want to be able to add a description and have it go to exactly the same place, so that the useful info is completely ignored by my application. mydomain.com/bike/1234/a-really-great-bike (pretty and useful) mydomain.com/index.cfm?Section=Bike&BikeID=1234 Issue #2 I need to be able to add a second or third parameter and value to the url to get extra info for the db, like this: mydomain.com/bike/1234/5678 mydomain.com/index.cfm?Section=Bike&BikeID=1234&FeatureID=5678 This works using this rule: RewriteRule ^bike/([0-9]+)/([0-9]+)$ /index.cfm?Section=Bike&BikeID=$1&FeatureID=$2 Again, I need to add some extra info, like in the first example: mydomain.com/bike/1234/5678/a-really-great-bike (pretty and useful) mydomain.com/index.cfm?Section=Bike&BikeID=1234&FeatureID=5678 So, how can I combine these rules so that I can have one or two or three parameters and any of the "useful words" are completely ignored?

  Read the article

• amavisd + postfix + dovecot blocks gif images

  - by David W

  I occasionally have a client who tries to email me and says his email gets blocked by my server. When I check the logs, I see this: Sep 6 18:12:52 myers amavis[15197]: (15197-08) p.path BANNED:1 [email protected]: "P=p003,L=1,M=multipart/mixed | P=p002,L=1/2,M=application/ms-tnef,T=tnef,N=winmail.dat | P=p004,L=1/2/1,T=image,T=gif,N=image001.gif,N=image001.gif", matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" And then a little later... Sep 6 18:12:58 myers amavis[15197]: (15197-08) Blocked BANNED (.image,.gif,image001.gif,image001.gif), [213.199.154.205] [157.56.236.229] <[email protected]> - > <[email protected]>, quarantine: banned-g4QhZGvwJvDF, Message-ID <6A9596BE385EC1499F83E464FA9ECCA20C668320@BY2PRD0611MB417.namprd06.prod.outlook.com>, mail_id: g4QhZGvwJvDF, Hits: -, size: 20916, 8439 ms From this and the bounce that he forwards me (to a different address I give him), I determine that its bouncing because of the file in his signature (image001.gif). However, that does NOT match the "key" in this part of the log: matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" Furthermore, the .gif extension is nowhere to be found in the /etc/amavisd.conf file (i.e. I'm not blocking emails because they contain .gif images). Am I missing something here? This is strange... and annoying.

  Read the article

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• VPN with client-to-client direct connectivity?

  - by Johannes Ernst

  When setting up a VPN, clients (say client1 and client2) usually authenticate to a server, and together the three constitute the VPN. When client1 wishes to send a packet to client2, this packet usually gets routed by way of server. Are there products / configuration blueprints for products where it is possible to send packets directly from client1 to client2 without going though server? (if the underlying network topology permits it, e.g. no firewalls in the way) If not, is there a way by which client1 can send a packet to client2 by way of server, without the server being able to snoop on the content of the packet? (E.g. because the packet is encrypted with the public key of client2) I just asked in the OpenVPN forum, and the answer I got was "not with OpenVPN". So my question is: are there other products with which this is possible? Open-source preferred ... One use case: client1 and client2, typically in separate offices, find themselves both at headquarters. Do they still need to talk to each other via the public internet? Links appreciated. Thank you.

  Read the article

• Windows Task Scheduler fails on EventData instruction

  - by Pete

  The Scheduled Task fails on the Event Data instruction in this XML: <ValueQueries> <Value name="eventChannel">Event/System/Channel</Value> <Value name="eventRecordID">Event/System/EventRecordID</Value> <Value name="eventData">Event/EventData/Data</Value> </ValueQueries> The other 2 fields can be passed as arguments and the EventData syntax matches other websites, so I don't know why it's failing. This is the Event Viewer XML: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Aptify.ExceptionManagerPublishedException" /> <EventID Qualifiers="0">0</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2013-11-07T19:39:14.000000000Z" /> <EventRecordID>97555</EventRecordID> <Channel>Application</Channel> <Computer>[Computer Name]</Computer> <Security /> </System> <EventData> <Data>General Information ********************************************* Additional Info: ExceptionManager.MachineName: [Computer Name] ExceptionManager.TimeStamp: 11/7/2013 12:39:14 PM ExceptionManager.FullName: AptifyExceptionManagement, Version=4.0.0.0, Culture=neutral, PublicKeyToken=[key] ExceptionManager.AppDomainName: Aptify Shell.exe ExceptionManager.ThreadIdentity: ExceptionManager.WindowsIdentity: ACA_DOMAIN\pbassett 1) Exception Information ********************************************* Exception Type: Aptify.Framework.BusinessLogic.GenericEntity.AptifyGenericEntityValidationException Entity: Tasks ErrorString: Task Type "Make Contact" is not active. MachineName: [machine] CreatedDateTime: 11/7/2013 12:39:14 PM AppDomainName: Aptify Shell.exe ThreadIdentityName: WindowsIdentityName: [identity] Severity: 0 ErrorNumber: 0 Message: Task Type "Make Contact" is not active. Data: System.Collections.ListDictionaryInternal TargetSite: Boolean Save(Boolean, System.String ByRef, Sys tem.String) HelpLink: NULL Source: AptifyGenericEntity StackTrace Information ********************************************* at Aptify.Framework.BusinessLogic.GenericEntity.AptifyGenericEntity.Save(Boolean AllowGUI, String& ErrorString, String TransactionID)</Data> </EventData> </Event>

  Read the article

• Dell XPS m1530 system cannot boot need 130w or greater

  - by KPS

  I have a Dell XPS M1530 and I lost my old AC adapter but ordered a new one. For the longest time it always had a battery charge so I was able to boot into the OS but now it is completely dead. I have a generic charger that slowly charged the laptop when it was in the OS but does not when the computer is off. When I boot up I get the following error: The AC power adapter type cannot be determined. The system can only boot with a 130 W power adapter or greater. Strike F1 key to shutdown. I cannot even enter the BIOs setup screen or boot menu, is there a way around this? I heard from the local tech that Dell has a special feature to boot from thumb drive before getting past the initial logo. I am doing my best to avoid purchasing a new charger since it worked just fine when the OS was running, I am hoping to get this thing going. Is there a way to charge the battery externally? Thanks in advance for any help!

  Read the article

• Mac OS X 10.8 VPN Server: Bypass VPN for LAN traffic (routing LAN traffic to secondary connection)

  - by Dan Robson

  I have somewhat of an odd setup for a VPN server with OS X Mountain Lion. It's essentially being used as a bridge to bypass my company's firewall to our extranet connection - certain things our team needs to do require unfettered access to the outside, and changing IT policies to allow traffic through the main firewall is just not an option. The extranet connection is provided through a Wireless-N router (let's call it Wi-Fi X). My Mac Mini server is configured with the connection to this router as the primary connection, thus unfettered access to the internet via the router. Connections to this device on the immediate subnet are possible through the LAN port, but outside the subnet things are less reliable. I was able to configure the VPN server to provide IP addresses to clients in the 192.168.11.150-192.168.11.200 range using both PPTP and L2TP, and I'm able to connect to the extranet through the VPN using the standard Mac OS X VPN client in System Preferences, however unsurprisingly, a local address (let's call it internal.company.com) returns nothing. I tried to bypass the limitation of the VPN Server by setting up Routes in the VPN settings. Our company uses 13.x.x.x for all internal traffic, instead of 10.x.x.x, so the routing table looked something like this: IP Address ---------- Subnet Mask ---------- Configuration 0.0.0.0 248.0.0.0 Private 8.0.0.0 252.0.0.0 Private 12.0.0.0 255.0.0.0 Private 13.0.0.0 255.0.0.0 Public 14.0.0.0 254.0.0.0 Private 16.0.0.0 240.0.0.0 Private 32.0.0.0 224.0.0.0 Private 64.0.0.0 192.0.0.0 Private 128.0.0.0 128.0.0.0 Private I was under the impression that if nothing was entered here, all traffic was routed through the VPN. With something entered, only traffic specifically marked to go through the VPN would go through the VPN, and all other traffic would be up to the client to access using its own default connection. This is why I had to specifically mark every subnet except 13.x.x.x as Private. My suspicion is that since I can't reach the VPN server from outside the local subnet, it's not making a connection to the main DNS server and thus can't be reached on the larger network. I'm thinking that entering hostnames like internal.company.com aren't kicked back to the client to resolve, because the server has no idea that the IP address falls in the public range, since I suspect (probably should ping test it but don't have access to it right now) that it can't reach the DNS server to find out anything about that hostname. It seems to me that all my options for resolving this all boil down to the same type of solution: Figure out how to reach the DNS with the secondary connection on the server. I'm thinking that if I'm able to do [something] to get my server to recognize that it should also check my local gateway (let's say Server IP == 13.100.100.50 and Gateway IP == 13.100.100.1). From there Gateway IP can tell me to go find DNS Server at 13.1.1.1 and give me information about my internal network. I'm very confused about this path -- really not sure if I'm even making sense. I thought about trying to do this client side, but that doesn't make sense either, since that would add time to each and every client side setup. Plus, it just seems more logical to solve it on the server - I could either get rid of my routing table altogether or keep it - I think the only difference would be that internal traffic would also go through the server - probably an unnecessary burden on it. Any help out there? Or am I in over my head? Forward proxy or transparent proxy is also an option for me, although I have no idea how to set either of those up. (I know, Google is my friend.)

  Read the article

• Why can`t we treat SSL Certs like Pgp keys instead of trusting CAs?

  - by yarun can

  I am dumb and stupid and I do not know all the technical aspects of SSL and server/client side implications and implementations. However I understand them good enough from user point of view to use SSL and encyrption daily. I was thinking that how silly it is to trust some unknown/known CAs when it comes to our our certificates for our servers. There had been many cases of misconduct, misuse, compromises and theft of certificates/ca keys from those places. On top of those known issues we also have to pay these guys regularly. I am wondering why can not we use/treat web server certificates like we use our pgp keys? So I sign a SSL certificate and send to a central server. And then each user accessing my site checks the validity and the keys from some central server (like pgp key servers). Is this a stupid idea? If so what could be a better idea than current system of issuing valid certificates. I am looking for a better than more secure idea. Naturally this is not a solution to an existing problem, rather it will be a hypothetical solution for some future implementation of a currently messed up web of trust on the internet due to recent news about NSA and their criminal buddies around the world. thanks

  Read the article

• What is the latest on Microsoft Expression Studio licensing?

  - by DanM

  In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

  Read the article

• Cannot send email outside of network using Postfix

  - by infmz

  I've set up an Ubuntu server with Request Tracker following this guide (the section about inbound mail would be relevant). However, while I'm able to send mail to other users within the network/domain, I cannot seem to reach beyond - such as my personal accounts etc. Now I have no idea what is causing this, I thought that all it takes is for the system to fetch mail through our exchange server and be able to deliver in the same way. However, that hasn't been the case. I have found another server setup in a similar fashion (CentOS 5, Request Tracker but using Sendmail), however it is a dated server and whoever's built it has kindly left no documentation on how it works, making it a pain to use that as a reference system! :) At one point, I was told I need to set up a relay between the local server's email add and our AD server but this didn't seem to work. Sorry, I know next to nothing about mailservers, my colleagues nothing about Linux so it's a hard one for me. Thank you! EDIT: Result of postconf -N with details masked =) alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = myhost.mydomain.com, localhost.mydomain.com, , localhost myhostname = myhost.mydomain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = EXCHANGE IP smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes Sample log message: Sep 4 12:32:05 theedgesupport postfix/smtp[9152]: 2147B200B99: to=<[email protected]>, relay= RELAY IP :25, delay=0.1, delays=0.05/0/0/0.04, dsn=5.7.1, status=bounced (host HOST IP said: 550 5.7.1 Unable to relay for [email protected] (in reply to RCPT TO command))

  Read the article

• Setting up subdomain to respond on :443 with apache2

  - by compucuke

  I read through some guides on this and I believe it is possible to have apache respond to a subdomain through ssl. I have domain.com responding on 80 and I do not need domain.com responding on 443. Rather, the only use I have for ssl is for the subdomain sub.domain.com. So my site should be http://domain.com http://www.domain.com https://sub.domain.com https://www.sub.domain.com My CNAME records are as follows sub.domain.com xxx.xx.xx.xxx *.sub.domain.com xxx.xx.xx.xxx The A record exists but should not matter for the example. I set up a separate config file in sites-enabled for sub.domain.com NameVirtualHost xxx.xx.xx.xxx:443 <VirtualHost xxx.xx.xx.xxx:443> SSLEngine on SSLStrictSNIVHostCheck on SSLProtocol -ALL +SSLv3 +TLSv1 SSLCipherSuite ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:-MEDIUM ServerAlias sub.domain.com DocumentRoot /usr/local/www/ssl/documents/ SSLCertificateFile /root/sub.domain.com.crt SSLCertificateKeyFile /root/sub.domain.com.key Alias /robots.txt /usr/local/www/ssl/documents/robots.txt Alias /favicon.ico /usr/local/www/ssl/documents/favicon.ico Alias /js/libs /usr/local/www/ssl/documents/js/libs Alias /media/ /usr/local/www/documents/media/ Alias /img/ /usr/local/www/ssl/documents/img/ Alias /css/ /usr/local/www/ssl/documents/css/ <Directory /usr/local/www/ssl/documents/> Order allow,deny Allow from all </Directory> WSGIDaemonProcess sub.domain.com processes=2 threads=7 display-name=%{GROUP} WSGIProcessGroup sub.domain.com WSGIScriptAlias / /usr/local/www/wsgi-scripts/script.wsgi <Directory /usr/local/www/wsgi-scripts> Order allow,deny Allow from all </Directory> </VirtualHost> Now, it is important to mention that https://domain.com responds with what I have running from script.wsgi above instead of on https://sub.domain.com. It does not respond to sub.domain.com. checking https://sub.domain.com causes a 105 error. This is a DNS error but I am convinced the DNS does not have a problem with the CNAME records, they just point to my IP. Am I doing something that Apache can not do?

  Read the article

• SYS-5016T-MTFB will not POST without manual assistance (Motherboard: X8STi-F)

  - by Dan

  I have a Supermicro 5016T-MTFB 1U server which I am in the process of setting up, but it has a really strange problem. When the system is powered on it will not POST until I press the reset button a few times, followed by pressing the delete key on the keyboard to "wake it up". If I power it on and do nothing, the fans spin up but nothing else happens at all. After pressing the reset button once, the red "overheat" light comes on and blinks which is supposed to indicate a fan failure - but all the fans are working. Pressing reset again usually stops the blinking, and the system starts the normal POST routine but it will not actually get to the bios screen unless I press delete. If I don't press delete, it just continues to hang. After pressing delete it will take me into the bios setup screen, if I exit without saving changes I can boot the system normally. I was able to successfully install Linux with no trouble...but upon rebooting the same problem happened again. This board has integrated IPMI which I thought was the problem, so I disabled it via the jumper on the board. Did not help. Each time this system powers on, it goes on for a second, then turns off again for another second, then turns back on again. I don't know why it does that. Here is what I put in the system: 1 x Xeon E5630 (Nehalem) 80W TDP (it's not overheating, CPU temps stay under 40 degrees C) 2 x Kingston 2GB x 3 DDR3-1066 Memory ECC, unbuffered, unregistered (kvr1066d3e7sk3/6g) 1 x Intel X25-M 160 GB 2 x Western Digital RE3 1TB

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• Issue booting Linux Mint from Live CD?

  - by Vee

  I had Windows 8 and Linux Mint 15 dual booted on my laptop. When I first installed Linux, I wasn't able to load into because the grub would not show. To fix this, I used boot-repair from a Live CD. This time, I updated to Windows 8.1 and it showed a watermark telling me my secure boot wasn't configured properly. I then went and enabled secure boot (BIOS) and I believe it was after that that the Grub would not show once again. I tried to boot from a Linux CD again but when I try, it gives me the following errors: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... Before, it was giving me an error with sector 0x6d200 or something instead of 0x0. I am completely unsure of what to do. I do not know what other details to give except that this my have happened after I enabled secure boot, and I actually clicked reset to default setting so I am unsure if any other settings were changed in the BIOS menu.

  Read the article

• How can I have puppet deploy ssh keys for virtual users?

  - by Pheezy

  I am trying to get puppet to assign authorized ssh keys for virtual users but I keep getting the following error: err: Could not retrieve catalog: Could not parse for environment production: Syntax error at 'user'; expected '}' at /etc/puppet/modules/users/manifests/ssh_authorized_keys.pp:9 I believe my configuration are correct (listed below) but is there a syntax error or scoping issue I am missing? I would simply like to assign users to nodes and have those users automagically have their ssh keys installed. Is there maybe a better way to do this and I'm just overthinking it? # /etc/puppet/modules/users/virtual.pp class user::virtual { @user { "user": home => "/home/user", ensure => "present", groups => ["root","wheel"], uid => "8001", password => "SCRAMBLED", comment => "User", shell => "/bin/bash", managehome => "true", } # /etc/puppet/modules/users/manifests/ssh_authorized_keys.pp ssh_authorized_key { "user": ensure => "present", type => "ssh-dss", key => "AAAAB....", user => "user", } # /etc/puppet/modules/users/init.pp import "users.pp" import "ssh_authorized_keys.pp" class user::ops inherits user::virtual { realize( User["user"], ) } # /etc/puppet/manifests/modules.pp import "sudo" import "users" # /etc/puppet/manifests/nodes.pp node basenode { include sudo } node 'testbox' inherits basenode { include user::ops } # /etc/puppet/manifests/site.pp import "modules" import "nodes" # The filebucket option allows for file backups to the server filebucket { main: server => 'puppet' } # Set global defaults - including backing up all files to the main filebucket and adds a global path File { backup => main } Exec { path => "/usr/bin:/usr/sbin/:/bin:/sbin" }

  Read the article

• 502: proxy: pass request body failed

  - by Andrei Serdeliuc

  Sometimes I get the following error (in apache's error.log) when viewing my site over https: (502)Unknown error 502: proxy: pass request body failed to xxx.xxx.xxx.xxx:443 I'm not entirely sure what this is and why it happens, it's also not consistent. The request route is: Browser Proxy server (apache with mod_proxy + mod_ssl) Load balancer (aws) Web server (apache with mod_ssl) The configuration on the proxy server is as follows: <VirtualHost *:443> ProxyRequests Off ProxyVia On ServerName www.xxx.co.uk ServerAlias xxx.co.uk <Directory proxy:*> Order deny,allow Allow from all </Directory> <Proxy *> AddDefaultCharset off Order deny,allow Allow from all </Proxy> ProxyPass / balancer://cluster:443/ lbmethod=byrequests ProxyPassReverse / balancer://cluster:443/ ProxyPreserveHost off SSLProxyEngine On SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /var/www/vhosts/xxx/ssl/www.xxx.co.uk.cert SSLCertificateKeyFile /var/www/vhosts/xxx/ssl/www.xxx.co.uk.key <Proxy balancer://cluster> BalancerMember https://xxx.eu-west-1.elb.amazonaws.com </Proxy> </VirtualHost> Any idea what the issue might be?

  Read the article

• Linksys router cannot change default password

  - by Jessica M.

  My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

  Read the article

• Exchange 2010 POP3/IMAP4/Transport services complaining that they can't find SSL certificate after blue screen

  - by Graeme Donaldson

  We have a single-server Exchange 2010 setup. In the early hours of this morning the server had a blue screen and rebooted. After coming back up the POP3/IMAP4 and Transport services are complaining that they cannot find the correct SSL certificate for mail.example.com. POP3: Log Name: Application Source: MSExchangePOP3 Date: 2012/04/23 11:45:15 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. SSL or TLS encryption can't be made to the POP3 service. IMAP4: Log Name: Application Source: MSExchangeIMAP4 Date: 2012/04/23 08:30:44 AM Event ID: 2007 Task Category: (1) Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: A certificate for the host name "mail.example.com" couldn't be found. Neither SSL or TLS encryption can be made to the IMAP service. Transport: Log Name: Application Source: MSExchangeTransport Date: 2012/04/23 08:32:27 AM Event ID: 12014 Task Category: TransportService Level: Error Keywords: Classic User: N/A Computer: exch01.domain.local Description: Microsoft Exchange could not find a certificate that contains the domain name mail.example.com in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Default EXCH01 with a FQDN parameter of mail.example.com. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. The odd part is that Get-ExchangeCertificate show the cert as enabled for all the relevant services, and OWA is working flawlessly using this certificate. [PS] C:\Users\graeme\Desktop>Get-ExchangeCertificate Thumbprint Services Subject ---------- -------- ------- XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX ....S. CN=exch01 YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY ....S. CN=exch01 ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ IP.WS. CN=mail.example.com, OU=Domain Control Validated, O=mail.exa... Here's the certificate in the computer account's personal cert store: Does anyone have any pointers for getting POP3/IMAP4/SMTP to use the cert again?

  Read the article

• How do I get the F1-F12 keys to switch screens in gnu screen in cygwin when connecting via SSH?

  - by Mikey

  I'm connecting to a desktop running cygwin via SSH from the terminal app in Mac OS X. I have already started screen on the cygwin side and can connect to it over the SSH session. Furthermore, I have the following in the .screenrc file: bindkey -k k1 select 1 # F1 = screen 1 bindkey -k k2 select 2 # F2 = screen 2 bindkey -k k3 select 3 # F3 = screen 3 bindkey -k k4 select 4 # F4 = screen 4 bindkey -k k5 select 5 # F5 = screen 5 bindkey -k k6 select 6 # F6 = screen 6 bindkey -k k7 select 7 # F7 = screen 7 bindkey -k k8 select 8 # F8 = screen 8 bindkey -k k9 select 9 # F9 = screen 9 bindkey -k F1 prev # F11 = prev bindkey -k F2 next # F12 = next However, when I start multiple windows in screen and attempt to switch between them via the function keys, all I get is a beep. I have tried various settings for $TERM (e.g. ansi, cygwin, xterm-color, vt100) and they don't really seem to affect anything. I have verified that the terminal app is in fact sending the escape sequence for the function key that I'm expecting and that my bash shell (running inside screen) is receiving it. For example, for F1, it sends the following (hexdump is a perl script I wrote that takes STDIN in binmode and outputs it as a hexadecimal/ascii dump): % hexdump [press F1 and then hit ^D to terminate input] 00000000: 1b4f50 .OP If things were working correctly, I don't think bash should receive the escape sequence because screen should have caught it and turned it into a command. How do I get the function keys to work?

  Read the article

• Resource Monitor (resmon) in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

  Read the article

• /usr/bin/python (Python 2.4) was deleted on CentOS 5. I compiled from source but yum is still broken. How can I get everything back to the way it was?

  - by Maxwell

  I saw a lot of other questions like this but none of them answered the exact part I am having trouble with (actually installing the Python RPM). Someone on my system deleted /usr/bin/python and /usr/bin/python2.4 on my 64 bit CentOS 5.8 installation. I recompiled Python 2.4 from source, but now whenever I try to yum install anything I get the following error: [root@cerulean-OW1 ~]# yum install httpd There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.4 (#1, Dec 16 2012, 09:16:56) [GCC 4.1.2 20080704 (Red Hat 4.1.2-52)] If you cannot solve this problem yourself, please go to the yum faq at: http://wiki.linux.duke.edu/YumFaq I checked http://wiki.linux.duke.edu/YumFaq and it said the following: If you are getting a message that yum itself is the missing module then you probably installed it incorreclty (or installed the source rpm using make/make install). If possible, find a prebuilt rpm that will work for your system like one from Fedora or CentOS. Or, you can download the srpm and do a rpmbuild --rebuild yum*.src.rpm I tried going to http://rpm.pbone.net/index.php3/stat/4/idpl/17838875/dir/centos_5/com/python-2.4.3-46.el5.x86_64.rpm.html to install Python, which resulted in the following error: [root@cerulean-OW1 ~]# rpm -Uvh python-2.4.3-46.el5.x86_64.rpm error: Failed dependencies: python-libs-x86_64 = 2.4.3-46.el5 is needed by python-2.4.3-46.el5.x86_64 So I tried installing python-libs-x86_64, which resulted in the following: [root@cerulean-OW1 ~]# rpm -Uvh python-libs-2.4.3-46.el5_8.2.x86_64.rpm warning: python-libs-2.4.3-46.el5_8.2.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID 192a7d7d Preparing... ########################################### [100%] package python-libs-2.4.3-46.el5_8.2.x86_64 is already installed file /usr/lib64/libpython2.4.so.1.0 from install of python-libs-2.4.3-46.el5_8.2.x86_64 conflicts with file from package python-libs-2.4.3-46.el5_8.2.x86_64

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• Windows 7 keeps insisting that it needs to check disk for consistency, but never does

  - by Mike

  Lately Windows 7 has been telling me that I need to check disk D: for consistency. This happens more than 50% of the time when booting up. The first time, I didn't touch anything so that it would go ahead and do its scan. It didn't seem to do anything - just booted straight into Windows. The second time I tried to skip it by pressing any key. It ignored all of my keystrokes and still counted down to 0 (then skipped the disk check). Sometimes, it gets down to 0 but then just hangs... no indication that anything is going on. This is happening on a < 3 month old laptop. C: and D: are on the same physical disk - just two partitions. I never get any notification that C: needs to be checked for consistency. It's a ~300GB HD. C: has 60gb (32gb free) and D: has ~240GB (122gb free). What could be causing this to keep coming up? What can I do to fix it? Thanks!

  Read the article

< Previous Page | 728 729 730 731 732 733 734 735 736 737 738 739  | Next Page >