Search Results

Search found 22170 results on 887 pages for 'multiple schema'.

Page 733/887 | < Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >

• Dell 2970 - HP 1/8 G2 autoloader keeps falling off LSI 2032 SCSI chain

  - by middaparka

  I've a somewhat irritating problem with a Dell 2970 that has a HP 1/8 G2 autoloader (the Ultrium LTO 2 model) attached to the Dell/LSI 2032 non-RAID SCSI card. In essence, sometimes the autoloader/drive completely fails to appear on the SCSI chain (i.e.: there's neither a media changer or tape drive present within the device manager) and sometimes it appears but then subsequently disappears at a seemingly random (yet always inconvenient) time, resulting in backup failures. On most occasions, there are simply no errors logged in the system event log, but I did manage to capture a series of LSI_SCSI event ID 11 ("The driver detected a controller error on \Device\RaidPort0") errors followed by an event ID 129, ("Reset to device, \Device\RaidPort0, was issued") error during testing. I've tried two different cables, both with the same effect – sometimes the autoloader appears (for a while), sometimes it's completely absent. There's only one terminator I've tried to use, but as I've since successfully tested the autoloader on multiple occasions (albeit via a Adaptec U160 card on a different machine), my gut feel is that the issue doesn't lie with the terminator, or indeed the autoloader itself. As such, I'm just wondering if anyone has any ideas? It's most likely not relevant, but this is all under Windows SBS 2008, running Backup Exec 12.5 SBS edition (the Dell version), both fully patched. Addidtionally, the autoloader is running the latest firmware. It's been a while since I've dealt with anything SCSI, so all suggestions will be gratefully, gratefully received.

  Read the article

• Share Exchange Calendar Outside Organization

  - by CalCurious

  I'm trying to figure out the best way to meet a user's (Corp-A-User) request to share their calendar with someone at another company (Corp-B-User). We're running Microsoft SBS 2008 with Exchange 2007 and SharePoint. The remote user is running Exchange, version unknown. Corp-A-User wants to give the Corp-B-User the ability to create appointments on Corp-A-User's calendar. This will naturally require sharing of Free/Busy information. Corp-A-User naturally lacks the vision to seen ANY problem with giving Corp-B-User full access to their calendar. But, I see the problems with that and would prefer that Corp-B-User have only the ability to see Free/Busy and create appointments. Most of the external publishing options that I have thought of, such as WebDav, allow displaying a user's calendar, but there are problems with security and the ability to create appointments. Right now, I'm thinking the cleanest solution would be to use a Google calendar along with Google Calendar Sync for the two user's Outlook clients. But, I'm not sure if there isn't a better way and I hate teh idea of pushing a corporate calendar up to Google. Not to mention the issues likely to pop up from the multiple sync paths. Does any one have a good solution for this scenario that would be willing to share what they use?

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• How to fix Quicktime video color problems on nVidia chipset and Windows XP?

  - by Matthew Glidden

  My laptop frequently plays video as if in very low-color mode. Though the sound remains clear, it looks terrible, showing only a few shades of red, blue, or yellow. (It's even worse than 8-bit color.) The problem doesn't happen consistently, so I'm looking for troubleshooting advice or known solutions. I use a Dell Latitude D620 laptop with Windows XP, on-board nVidia video chipset, Quicktime, and multiple monitors (laptop screen + VGA-connected LCD). Color problems happen in each application I tried, iTunes, a browser, and the Quicktime standalone player. It doesn't happen right after reboot, so could be from a sleep-wake cycle, or at least being on for an extended period. Google results suggest reinstalling nVidia drivers, which I've done several times with no change. I have found 2 workarounds. Reboot, sacrificing significant time and disrupting work In nVidia control panel, change color to 16-bit, and then back to 32-bit This happens with all video playback, so it's definitely not one corrupt file. I use workaround #2 consistently, but would love a longer-term solution.

  Read the article

• Need help using a super scope

  - by Vdub

  I have a windows server 2008 r2 standard running our DCHP, DNS, and AD. also I have (3) HP Pro Curve 2510-G switches (J9280A). Right now our LAN is set up 192.168.50.2-192.168.50.254 on our sub-net (A) and another scope with 192.168.51.2-192.168.51.254 sub-net (B) both have sub-net mask of 255.255.255.0. The same server is our DNS which is 192.168.50.242 and our firewall (watchguard) is the gateway at 192.168.50.1. Right now the sub-net (B) does not have DHCP active so only sub-net (A) is giving a pool. My problem is that we are trying to have open WiFi on our network and i am assuming that i can use the sub-net (B) for that if i activate it and use sub-net (A) for our staff only. I have noticed that when i set up a static on a client pc and set it to 192.168.51.x i cannot use the DNS of 192.168.50.242 however i can use 8.8.8.8 and it works fine, i am guessing that because it is on a different sub-net? Forgive me as i am very new at this and dont know a lot. Is there easy way with the equipment i have to a accommodate wifi for hundreds of people without causing problems for our staff? (multiple same IP address assigns) I appreciate any and all info!

  Read the article

• Libraries merged folder views

  - by Stigma

  So I pretty much love the Windows 7 Libraries feature, and saw one use for them that I thought would be perfect, but I can't seem to manage it. Basically, a merged view of different folder structures. Suppose I make a new generic library and add three locations to it: C:\Test\, D:\Test\ and D:\temp\Test\. Now, these may look somewhat okay as long as there are no duplicates in these folders. (It wants to group them based on the included directory, which one can work around by looking on google - I don't have the precise trick on hand I am afraid.) But when you get collisions and, say, two of those directories have a Sub directory in them, stuff becomes unusable (assuming Arrange by: Folder view). You'll have multiple folders listed named Sub, which is pretty useless when looking for data. I want folders to get 'merged', which ought to be possible somehow since it can create these merged views based on artist, album etc in other views. So all subdirectories that are double (and recursively checking for doubles inside those, etc) ought to be merged for as far the View is concerned. If files have a collision, I don't really care what happens - hide one, show both, filter out duplicates, whatever. (Although an option would be nice...) Anyhow, is there anyone who knows how to get such a 'merged folder structure' functionality for Libraries? It would be really useful for me.

  Read the article

• What are the biggest, best CPUs that support Physical Address Extension?

  - by Giffyguy

  I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

  Read the article

• VPN Client solution

  - by realtek

  I have several VPN's that I need to establish on a daily basis but from multiple workstations. What I would like to do it have either a server or vpn router that can perform this connection itself and that I can then route traffic through this device or server depending on the subnet I am trying to reach. The issue is that I only use VPN Clients to connect, so I am basically trying to achieve almost a site to site VPN but by using basically a VPN Client type connection from my network. The main VPN Client I use is the Sonicwall Global VPN Client where I initially use a Preshared Key and then it always prompts me for a username and password (not RSA key). My question is, is there any type of linux distro or even a hardware vpn router that can do this and connect to a Sonicwall device as if it were a client? I have tried pfSense which is very good but it fails to connect, probably due to a mismatch of settings. I have tried many others. Even dd-wrt on my router but it does not support whatever protocol Sonicwall uses. (I thought L2TP/IPSec) but it appears it may not be that. Any advice would be great! The other other thing I have thought of that I have not tried yet is Windows Server Routing and Remote Access but I have a feeling that won't work either. Thanks

  Read the article

• Do any well-known CAs issue Elliptic Curve certificates?

  - by erickson

  Background I've seen that Comodo has an elliptic curve root ("COMODO ECC Certification Authority"), but I don't see mention of EC certificates on their web site. Does Certicom have intellectual property rights that prevent other issuers from offering EC certificates? Does a widely-used browser fail to support ECC? Is ECC a bad fit for traditional PKI use like web server authentication? Or is there just no demand for it? I'm interested in switching to elliptic curve because of the NSA Suite B recommendation. But it doesn't seem practical for many applications. Bounty Criteria To claim the bounty, an answer must provide a link to a page or pages at a well-known CA's website that describes the ECC certificate options they offer, prices, and how to purchase one. In this context, "well-known" means that the proper root certificate must be included by default in Firefox 3.5 and IE 8. If multiple qualifying answers are provided (one can hope!), the one with the cheapest certificate from a ubiquitous CA will win the bounty. If that doesn't eliminate any ties (still hoping!), I'll have to choose an answer at my discretion. Remember, someone always claims at least half of the bounty, so please give it a shot even if you don't have all the answers.

  Read the article

• One-To-Many Powershell Scripts

  - by Matt

  I'm trying to create a script to run as a scheduled task, which will run against multiple servers and retrieve some information. To start with, I populate the list of servers by querying AD for all servers that match a certain set of criteria, using Get-ADComputer. The problem is, the list is returned as an object, which I can't then pass to the New-PSSession list. I have tried converting it to a comma-seperated string by doing the following: foreach ($server in $serverlist) {$newlist += $server.Name + ","} but this still doesn't work. the alternative is to iterate through the list and run the various commands against each server one at a time, but my preference would be to avoid this and run them using one-to-many remoting. UPDATE: To clarify what I want to end up being able to do is using -ComputerName $serverlist, so I want $serverlist to be a string rather than an object. UPDATE 2: Thanks for all the suggestions. Between them and my original method I'm starting to wonder whether -ComputerName can accept a string variable? I've got varying degrees of success getting the list of computers converted to a comma separated string, but no matter how I do it I always get invalid network address.

  Read the article

• How should I set up protection for the database against sql injection when all the php scripts are flawed?

  - by Tchalvak

  I've inherited a php web app that is very insecure, with a history of sql injection. I can't fix the scripts immediately, I rather need them to be running to have the website running, and there are too many php scripts to deal with from the php end first. I do, however, have full control over the server and the software on the server, including full control over the mysql database and it's users. Let's estimate it at something like 300 scripts overall, 40 semi-private scripts, and 20 private/secure scripts. So my question is how best to go about securing the data, with the implicit assumption that sql injection from the php side (e.g. somewhere in that list of 300 scripts) is inevitable? My first-draft plan is to create multiple tiers of different permissioned users in the mysql database. In this way I can secure the data & scripts in most need of securing first ("private/secure" category), then the second tier of database tables & scripts ("semi-private"), and finally deal with the security of the rest of the php app overall (with the result of finally securing the database tables that essentially deal with "public" information, e.g. stuff that even just viewing the homepage requires). So, 3 database users (public, semi-private, and secure), with a different user connecting for each of three different groups of scripts (the secure scripts, the semi-private scripts, and the public scripts). In this way, I can prevent all access to "secure" from "public" or from "semi-private", and to "semi-private" from "public". Are there other alternatives that I should look into? If a tiered access system is the way to go, what approaches are best?

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

• pfSense router on a LAN with two gateways

  - by JohnCC

  I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

  Read the article

• Is Gmail Being Blocked by my ISP (wait till you read this)?

  - by James

  This is the strangest thing I have ever encountered. I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). So okay, maybe my ISP is blocking these for some reason or maybe my firewall is, or maybe there is something wrong with my connectivity, right? NO. On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail ages starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping a complete reinstall would solve the issue, but no luck. So can anyone for the life of them figure out why this could be? And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cabel from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before gmail was perfectly accessible in this computer. I can't remember anything special that happened on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• Windows 7 task bar stuck in hiding, how to fix?

  - by Rainer Blome

  In Windows 7, I use the "Auto-hide the task bar" feature. Usually, it works fine: As soon as the pointer touches the screen bottom, the task bar pops up. However sometimes, it refuses to rise. Pressing the "Windows" key (or Ctrl-ESC) makes the start menu appear, forcing the task bar from hinding as well. Once I've done this, the task-bar auto-rises again. This is annoying, it interrupts flow. Has anyone else noticed this? How do I avoid this? Searching for "Windows 7 task bar auto-raise" shows that at least one other person experienced this problem: http://answers.microsoft.com/en-us/windows/forum/windows_7-desktop/how-can-i-fix-the-taskbars-auto-hide/8cdf6369-7354-4d29-9249-b7096ed0e28b?msgId=6dac3361-9d0f-4a9e-8642-b91a72826ba4 To answer the question posed by the "helpful" support engineer on the above page, of course I am running some apps when this happens, usually Explorer, Firefox, Eclipse, Cygwin/X, Xterm, Emacs, Notes, VPN client, Firewall. If my memory serves correctly, I have seen this behavior on earlier versions of Windows as well, XP at least. To reproduce this behavior, I tried switching between apps, and bringing apps to open other windows. I am unable to reproduce this behavior so far. So far, it appears to happen out of the blue, sometimes multiple times a day. Looks like a bug to me. The task bar should raise no matter what.

  Read the article

• Active Directory Password Formats

  - by Brent Pabst

  Hi, I'm working on an open source project that will manage active directory users. I am looking for feedback from Windows/Active Directory Admins on the formats of usernames they prefer or their organization uses. I want to make sure the software allows admins to use the most popular formats when new users are created. Here is the list I have so far: 1. <firstname><lastname> 2. <lastname><firstname> 3. <lastname><firstinitial> 4. <lastname><firstinitial><middleinitial> 5. <firstinitial><lastname> 6. <firstinitial><middleinitial><lastname> 7. <firstname><lastinitial> In addition how do you handle multiple identical names? So if two John Smith's exist do you append a numeric number, or interject a middle initial or name to solve the problem? Thanks for the feedback

  Read the article

• Malware Defense Shows Up in PlayOn Settings/Logs Although System Has Been Thoroughly Cleaned

  - by nicorellius

  I was hit really hard by some nasty malware: Malware Defense. I was doing something I should not have been doing when I got it (surfing Pirate Bay for TV shows). It locked up my system and I had to reboot in safe mode. I was able to shut down the process and remove it using a malware killer tool. I then installed, after my machine was cleaned up a bit, Clamwin, Malwarebytes, and another AV tool. I cleaned the heck out of my system. Simultaneously, while this was going on, I was having trouble with my media-server, PlayOn. This tool is great, but has some bugs. One in particular is that it will not function well with AV software running. I found a way to allow the new AV software to run while using PlayOn, but it still says I have Malware Defense on. Firstly, Malware Defense is long gone. I cleaned all remnants from my registry and scoured my system with the above tools multiple times. PlayOn is getting some information that I have this crap installed on my system, but it's not. The system runs OK, but not optimally. I have a feeling it is causing my streaming to be interrupted sometimes. How is it that I can't even find Malware Defense on my system if I tried but yet somehow PlayOn is getting a finger print of it somewhere? I have gone back and forth with MediaMall to no avail. I kind of just gave up, because the streaming works OK. BTW, I also uninstalled/reinstalled PlayOn several times, reverted back to previous versions, etc. The only thing I haven't done is reformat my disk and reinstall Windows. I really don't want to do this if there is another way to remove this little print. Any ideas?

  Read the article

• Copy/paste filtered column in Excel - error message

  - by hazymat

  Firstly I should state that I don't believe in spreadsheets; my normal mode of operation is that data should either exist in a database or a text file... However - employment requires... In short, I have filtered a worksheet by column A, and I want to copy/paste from column B to column C. Obviously I don't wish to copy/paste values from rows that were filtered-out here. The above sounds ridiculously simple, right? First I tried simply copy/pasting on the filtered worksheet. This appeared to select and copy only the filtered data, however pasting appeared to insert values into hidden/filtered rows - as you might expect. So my initial research suggests I may wish to select the filtered data and press Alt+; (that is, ALT plus semicolon), which is a shortcut key for Goto Special Select Visible. Then just copy-paste. CTRL+C correctly copies the filtered data, however when I go to paste the values into another column, it pastes into hidden rows as well. Okay, so perhaps I should also "Select Visible" on the cells I wish to paste into as well? Nope - that gives me the error That command cannot be used on multiple selections. What am I doing wrong?!

  Read the article

• Having trouble mapping Sharepoint document library as a Network Place

  - by Sdmfj

  I am using Office 365, Sharepoint Online 2013. Using Internet Explorer these are the steps I have taken: ticked the keep me signed in on the portal.microsoftonline.com page. It redirects me to Godaddy login page because Office 365 was purchased through them. I have added these sites to trusted sites (as well as every page in the process) and chose auto logon in Internet explorer. Once on the document library I open as explorer and copy the address as text. I go to My Computer and right click to add a network place and paste in the document library address. It successfully adds the library as a network place 30% of the time. I can do this same process 3 times in a row and it will fail the first 2 times and then succeeds. It works for a little while and then I get an error that the DNS cannot be found. I need multiple users in our organization to be able to access this document library as if it was a mapped network drive on our local network. Is there an easier way to do this? I may just sync using the One Drive app but thought that direct access to the files without worrying about users keeping their files synced.

  Read the article

• Outlook won't re-connect to exchange after network is re-connected

  - by stan503

  I have a setup at my desk where I connect my computer to a an RJ45 switch that switches between two networks. One network is the corporate network, which is maintained by my company's IT, and the other is my own private network where I do testing (the two networks have to be separated). The corporate network hosts the exchange server where I get e-mail. When I switch from the private network to the corporate network, I expect Outlook to re-connect to the exchange server. However, I have found that sometimes when I come back, Outlook take an extremely long time to re-connect. Send/Receive will give me back the error 'The server is not available' (0x8004011D). It will sit there for 10 minutes to a few hours before it finally re-connects. The only other option is to reboot my computer, which is a huge pain for me since I run multiple VMs on it. This usually happens when I'm connected to the private network for a significant amount of time, so I'm thinking it's because Outlook has cached the network status. Is there a way to force Outlook to do a 'hard' re-connect to the exchange server? I'm using Windows XP SP 3 with Outlook 2007.

  Read the article

• Coming from Win XP to 7 and having new accessibility software problems

  - by Anonymous Jones

  I just switched from Windows XP Pro SP3 (32bit) to Windows 7 Ultimate (32bit) on a new PC. Now, both the new onscreen keyboard and a utility for sending mouse clicks are being problematic. The problem with 7's OSK is that some things I type only work intermittently or just dodgily. Like Alt+Tab with multiple Tabs, other Alt/Ctrl/Shift/Win key combinations, and the context menu key. Sometimes apps will not take focus for input at all. I use the OSK it in 'hover' mode, on 0,5 seconds. The clicking tool is Point-N-Click, which sends clicks when I dwell anywhere for 1.25 seconds with the mouse pointer. http://www.polital.com/pnc/ The problem with it is that sometimes it fails to click. Most often this happens in some of the control panel sections, on the taskbar, and when UAC pops up. It seems to occur in conjunction with OSK usage a bit too, I think. I'm using an Administrator account. DEP and UAC settings are default. What can I do to fix or work around either of these problems? I'm disabled so this really is killing usability.

  Read the article

• Some free cloud solution to enhance your business

  - by Saif Bechan

  I am co-owner of a small internet business. I am in charge of IT, and I try to get things done as low cost as possible. When investing in servers, resources and overall business costs your project can soon turn into a financial disaster. Cloud solutions can help you in solving some financial problems, they can help you in scalability problems, and overall performance problems of your server or web application. Recently I moved the whole internal/external communication(email,calendar,documents) of my business to the cloud. I did this by using the free version of Google Apps. This works great and is a big advantage on multiple levels. I do not have to fight spam anymore on my system, and there are less resources used on my system. Also switching servers will go a lot easier. Questions Can you name some cloud solution that you have used, or some you just recommend. They can fairy form financial benefits, organizational benefits, performance benefits. It doesn't matter as soon as it helps you spread the load of your business.

  Read the article

• nginx projects in subfolders

  - by Timothy

  I'm getting frustrated with my nginx configuration and so I'm asking for help in writing my config file to serve multiple projects from sub-directories in the same root. This isn't virtual hosting as they are all using the same host value. Perhaps an example will clarify my attempt: request 192.168.1.1/ should serve index.php from /var/www/public/ request 192.168.1.1/wiki/ should serve index.php from /var/www/wiki/public/ request 192.168.1.1/blog/ should serve index.php from /var/www/blog/public/ These projects are using PHP and use fastcgi. My current configuration is very minimal. server { listen 80 default; server_name localhost; access_log /var/log/nginx/localhost.access.log; root /var/www; index index.php index.html; location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www$fastcgi_script_name; include fastcgi_params; } } I've tried various things with alias and rewrite but was not able to get things set correctly for fastcgi. It seems there should be a more eloquent way than writing location blocks and duplicating root, index, SCRIPT_FILENAME, etc. Any pointers to get me headed in the right direction are appreciated.

  Read the article

• IIS 8 URL Redirect on site level

  - by jackncoke

  I am trying to do a simple 301 perm redirect to another url in IIS 8. The end results would be if i navigated to domain2.com i would end up on domain1.com. We are moving from IIS 6 to a new server and have aprox 600+ sites that will be configured on this IIS 8 box. All of these sites run a property CMS and are looking at the same directory for source code. In IIS 6 i would just go to the Home directory tab of each site and check the box that says "Permanent Redirect" and provide a URL. With IIS 8 there is "HTTP Redirect" and this looks like it would do the trick but it is being applied to all the sites in IIS 8. Not on the site level like it use to be in IIS 6. I also looked into URL Rewriting module for IIS 8 but it seems to take rules in the style of a firewall and i am not sure if i could effectly create rules that would cater to 600+ sites. I am looking for the easiest way to have redirects on my site level so that that customers with multiple domains can have there sites redirect to there main domain for seo purposes. I feel like this was so easily achieved in IIS 6 that i must be overlooking something in the new version.

  Read the article

< Previous Page | 729 730 731 732 733 734 735 736 737 738 739 740  | Next Page >