Search Results

Search found 68828 results on 2754 pages for 'knapsack problem'.

Page 735/2754 | < Previous Page | 731 732 733 734 735 736 737 738 739 740 741 742  | Next Page >

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• The USB mouse sticks in Windows 7 after automatic attempt to fix the boot

  - by chelder

  Avast Antivirus asked me to delete a probable virus and to restart to perform a checking. I had to stop the checking at the middle of the procedure as I needed the computer. It was imposible to turn off the computer pushing the power button (as it entered in suspension mode, no matter how long I kept pushed the power button). I removed the battery as the only way to restart the computer. Windows 7 said that there is a problem to iniziate Windows. Windows 7 tried to fix the problem without success. Windows 7 started after that though. Everything is OK but the USB mouse. The USB mouse sticks and freezes each couple of seconds more or less. The tactile mouse (PS2) works well. I googled for solutions but the posible solutions didn't work for me. What happened? How could I fix it without formatting and reinstalling everything? UPDATE: this is what I did: Change the mouse from one usb port to another Test another mouse Set the number of cores of the CPU manually with msconfig Power management: not disable usb ports Check hard disk errors

  Read the article

• Ensure Mac's get correct machine name from DHCP?

  - by Greg Whitfield

  I have a problem in our network where our Mac's occasionally get given the wrong machine name while, I guess, getting a new DHCP lease. The DHCP servers are Windows based - the bulk of our network is Windows, but we have some Linux machines and an increasing number of Macs. The problem specifics is that occasionally a Mac will take on the name of another machine in the network. For example, I have a new Macbook Pro. In the OSX setup is gets called "gomez", and initially starts up on the network with that name without any problems. But after a few days when the machine was restarted (it had several restarts in the meantime), it ended up being called "florrie", which is actually the name of another machine in another part of the network. All network ops work fine, and indeed you don't notice most of the time - it's only when you run apps like Perforce that require the hostname that you get problems. I'm sorry I don't have more info than that, but if I know what to look for I can dig out some more facts. Or any hints on checking the network setup would be useful.

  Read the article

• Wrong CSS mime type with Roundcube 0.5 beta and nginx

  - by Julien Vehent

  I'm running into a CSS problem. This is a setup based on Debian Squeeze (nginx/0.7.67, php5/cgi) on which I installed the latest Roundcube 0.5 beta. PHP is properly processed, login works fine but the CSS files are not loaded and Firefox is throwing the following errors: Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/common.css?s=1290600165 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/mail.css?s=1290156319 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 As far as I understand, nginx doesn't see the .css extension (because ofthe ?s= argument) and thus set the mime type with the default value, being text/html. Should I fix this in nginx (and how ?) or is it roundcube's related ? Edit: It seems that it's nginx related. The content-type isn't set for any other type than text/html. I had to include manually the following declarations to force CSS and JS content-types. That's ugly, and I never had the problem before... any idea ? location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; }

  Read the article

• Laptop hangs on POST and does not finish except on rare occasions

  - by user1049697

  I have an old Toshiba Satellite A100 laptop that hangs on POST when I try to start it. On rare occasions it does finish the POST and boots Windows successfully, but most times it just finishes it partially and continues to hang. I can enter the BIOS though when it has frozen, but I have to open the DVD-drive first for some reason. The keyboard is not quite right either, and I can't navigate the BIOS properly because the arrow keys doesn't work. I tried an external keyboard, but the problem persisted. I have tried to remove the memory, hard drive, and battery to see if any of these were the problem, but it did not solve it. The one logical thing left to do would be to remove the CMOS battery, but the "brilliant" engineers at Toshiba have place it such that a complete disassembly of the machine is necessary. What this all boils down to is basically the question of whether I can "save" this machine and get it to boot properly, or if I should just send it off to recycling. I suspect it might need costly repairs, but I can't bring myself to throw it away before I have made sure it's completely dead.

  Read the article

• svnsync loses revision properties although hook installed

  - by roesslerj

  Hello all! I have a pretty weird problem. We have setup an SVN-Mirror via cronjob (because it needs to go from inside to outside of a firewall, so no post-commit-hook possible) and svnsync. We installed a pre-revprop-hook just as told. Everything seems to work fine, except that it doesn't. E.g. when manually executing the script. # svnsync --non-interactive sync file://<path-to-mirror> --source-username <usr> --source-password <pwd> Committed revision 19817. Copied properties for revision 19817. No error, no complaints. But if checking for the revision properties it says: # svnlook info <path-to-mirror> 0 # svn info -r HEAD file://<path-to-mirror> 2>&1 Path: <root-of-mirror> URL: file://<path-to-mirror> Repository Root: file://<path-to-mirror> Repository UUID: <uid> Revision: 19817 Node Kind: directory Last Changed Rev: 19817 So somehow the author and timestamp information gets lost. But we need that information for our internal processes. Since no error or warning is produced I have absolutely no idea even where to start to look. Everything is local (except for the remote master), so there are no server-logs to look at. I also tried to manually recopy via svnsync copy-revprops (http://chestofbooks.com/computers/revision-control/subversion-svn/svnsync-Copy-revprops-Ref-svnsync-C-Copy-revprops.html). It says Copied properties for revision 19885. But when I query them, it's just the same. Any ideas how I could approach that problem, or even better -- how to solve it? Any ideas appreciated.

  Read the article

• Exclamation 403 forbidden for cgi-bin/ and cannot protect site with password

  - by gasgdasdgasdg

  First problem i have is i am getting 403 forbidden error for cgi-bin/ I have created a new /var/www2/ i can access it fine. php runs fine. Second problem is I cannot password protect it. i first tried doing htpasswd, it asks for login but everytime i login it keeps asking for new one. its getting frustrating, i have tried all tricks. and doesn't seem to work. this is a virtual host config inside sites-available. httpd.conf is empty but i have apache2.conf Code: NameVirtualHost 12.12.12.12. <VirtualHost 12.12.12.12> ServerAdmin webmaster@localhost DocumentRoot /var/www2/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www2/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /var/www2/cgi-bin/ <Directory "/var/www2/cgi-bin/"> AllowOverride Options Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch AddHandler cgi-script cgi pl Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost>

  Read the article

• SQL Server 2008 second instance times out when logging in -- but only the first time?

  - by Kromey

  This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

  Read the article

• Google Apps Sync bloated PST file to 14GB

  - by James S

  Back story: I have Outlook connected to my Google Apps email and noticed that some mail never got migrated from my original PST file. I found some VBA code online that compares mail in different PST folders, modified it to find missing and copy those to the target folder. I ran it folder by folder and moved missing mail. Before the exercise the Google Apps PST was about ~4GB and after it was ~4.7GB. Problem: I left Outlook open so Google Sync can copy it online. 24 hours later the Google Apps PST file bloated to 14GB+ and none of the mail has been synced to the cloud. I know that there should be at most ~5GB of mail. Why is the rest of the space being taken up? Funny thing is Gmail shows 3GB as being used online. What I tried: I emptied the deleted items folder and recycling bin I've run Outlook compact PST and it didn't work. I tried SCANPST.exe on the PST and it didn't work. I re-ran compact PST and it didn't work (after SCANPST found and fixed a few errors) Any ideas out there on what caused the problem and how to solve it?

  Read the article

• It takes a long time until Windows XP recognize I connected USB drive

  - by Pavol G

  I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

  Read the article

• File permissions question

  - by Matthew Robert Keable

  I just switched my site's server from Windows to Linux, and am finally able to control file permissions from my ftp. So, seeing that all permissions were 705 by default (and not wanting just anyone to have permission to execute), I went and changed everything to 744. Now, gif and jpg links don't work, pdf download links don't work, php links don't load, and mov files don't play. Conversely, all html files work perfectly. Setting things back doesn't seem to help. Even setting to 777 gets me nowhere. Any ideas on what might be going wrong? I've been googling file permissions all day (solved that problem with the Windows-Linux switch, which has bred a new problem), and I don't think anything I can find has escaped my attention. The site: absis-minas.com Go easy on a n00b. I took up learning php out of interest, and wound up delving into server management issues due to a very simple line of code not working the way it was supposed to. Thanks!

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• Is there any free software to check for issues with a DVD drive?

  - by AgentConundrum

  I don't usually play movies on my laptop (prefer the standalone with the tv), but I tried to watch one the other night, and noticed playback was really choppy and had audio artifacts in places. I thought it could be related to memory issues so I rebooted and tried again, but the results were the same. I considered that it could be an issue with the disc, so I tried to clean it but again there was no change. I don't think the problem is with the disc, because I tried another disc and it also had the same problem. I don't think I've ever watched the second disc since I've had it, so it should have been safe in its jewel case. Also, there were no issues when I watched an episode off the first disc in my standalone player. What I'm wondering is: are there are any (free) utilities that can check for issues with the drive itself? I looked around but most of the software I found focuses on integrity checks for the disc, not the drive. I have had issues with this laptop recently (had to replace the keyboard when the cat damaged it while I was cleaning dust out and the machine was ripped apart, also replaced part of the chassis after I cracked it when I tried to open it not knowing a screw was still in it) so I may have just replaced the drive incorrectly. I'm going to check on this while I await an answer to this question. Thanks.

  Read the article

• Unable to write DVD-R(Blank DVD's)

  - by FrozenKing

  I have a problem in dvd drive i.e. It can read CD/DVD and can write CD and all CD/DVD-RW but cannot write DVD DVD drive model is SH-S203B Samsung; I also have a log file created by nero burning rom 11. Actually the fact is no Blank DVD's are being read in my dvd drive only previously written dvd's can be read! Is this the problem of OS or should I try cleaning the dvd drive or my DVD drive is 4yrs old so is it going to spoil now, since it is showing this type of symptoms! OS = WinXP AV = KIS 2012 DVD Drive = Samsung SH-S203B (Also tried latest firmware and downgrade versions also) IA32 Nero Version: 11.2.4.100 Internal Version: 11,2,4,100 Recorder: <TSSTcorp CDDVDW SH-S203B>Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 Drive buffer : 2048kB Bus Type : via Inquiry data CD-ROM: <TSSTcorp CDDVDW SH-S203B >Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 18:58:10 #37 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 00 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:10 #38 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 0 to 14 <Padding> 18:58:19 #39 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 10 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:19 #40 SectorVerify 21 File Cdrdrv.cpp, Line 12057 Read error at sector 15 <Virtual Multisession Info> 18:58:19 #41 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 16 to 18 <Volume Structure Descriptor Sequence> 18:58:28 #42 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 20 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000

  Read the article

• Mac and L2TP VPN no problems, xp, vista and 7 no go :s

  - by The_cobra666

  Hi all, I've got some weird problem and I'm out off options. The situation: When connecting from my mac to the VPN server (Windows Server 2003 R2) with L2TP PSK, everything works like it should. However, when I connect from a Windows PC, nothing happens. it spits out error 809 and sometimes 789. Now I know that my ports are OK, since the mac can connect without any problems. It's the same for: XP, Vista SP2 and 7. None can connect. If I connect to the VPN server directly (to the internal IP instead of WAN from the router), it connect's without a problem. Connecting using PPTP works... now if only L2TP would work thank you very much Windows! I have checked the counters on my linux router with iptables -L -nv and they do not raise when connecting. Not on ACCEPT and not on DROP. Only when connecting from the mac. I've found the guide from Microsoft to enable: AssumeUDPEncapsulationContextOnSendRule in the registery. I have set it to "2", on the server and client. Still no go. After that registery key it started giving me error 789 instead of 809. The IPSEC services are running on the client and server. Is there anyone that ppleease can help me with this! I've been working on this for 2 days and I'm out of options. Thanks!

  Read the article

• File in use when it's really not

  - by C-dizzle

  I am running Windows 7 Professional 32 bit on a Server 2008 network. I am getting a weird issue with an excel document where I open it up one morning, update it, save and close, the next morning I come in, open it up and it says "This file is in use and locked by csmith" which "csmith" is me! So I click on the cancel button, open it up again and it comes up fine. I can edit, save and close with no problem. But then have the same issue the next morning. Another weird thing is that we have a calendar shared in "Public Folders" under Outlook that seems to be having the same issue, which happens to be a calendar made in Excel. Exchange 2010 is installed on the server and the clients are using Exchange 2007. In the instance with the calendar, it will show conflicting edits have been made and you must keep one item or all items. And it shows an edit date of 4/24/2012 and 6/1/2012. But, there were NO edits done on 6/1, just tried opening it. This problem does not occur under my profile, but 2 others. These machines are ALSO running Windows 7 Professional 32 bit. We have a mix of Windows 7 and Windows XP machines on our network if that is any help. These issues did not start happening until we migrated from a server running Server 2003 and Exchange 2000, which the new server is running Server 2008 and Exchange 2010 as stated above. Is there something on the server side that is configured wrong?

  Read the article

• dhclient requests filling memory?

  - by shanethehat

  Dammit Jim, I'm a web developer, not a sys admin. With that out of the way, my client's has a CentOS server (6.2) that is only serving a single Magento site (and the associated MySQL server) and it is frequently running out of memory, despite the site only currently being open to 5 users. I'm investigating the logs to try to figure out why the memory usage is so high, but I don't really know what I'm looking at. It seems that there are a lot of entries in /var/log/messages concerning DHCP requests, approximately one every 15 seconds, that look like this: Apr 7 14:23:06 s15940039 dhclient[815]: DHCPREQUEST on eth0 to 172.30.102.85 port 67 (xid=0x6b5cd2a7) Is this normal? I don't see anything else in here that I don't recognise, but then I'm not sure I'd know the problem if I did see it. 4 days ago the server ran out of memory completely and locked up, requiring a restart. The DHCP messages did not start up again for 23 hours, but then carried on as before. I have read this question which describes the same issue, but in my case a fresh DHCP lease does not ever seem to be issued. Is this something I should push back to the hosting provider, or have I not yet found the source of the memory problem?

  Read the article

• SQL 2008 Backups to UNC Share Failing 0xC002F210

  - by Matty Brown

  This problem is driving me NUTS!! We take backups of all of our production databases to a network share, which are then backed up to tape nightly. 8pm Mon-Fri - Full backup, followed by log backup 7am-7pm Mon-Fri, at half-hour interval - Log backup Our backups have been working in this manner since we migrated from SQL Server Standard 2000 to 2008, 3 years ago. Recently, the first log backup on Mondays have been failing. Not every time, but almost every time! The rest of the week, we've had no problems. I guess the issue may have something to do with the size of the log backup that's attempted after a weekend of no backups. Now onto the issue I need a fix for... All this week, every full backup on our biggest two databases have failed (Both backups < 1GB compressed). There's plenty of disk space on the source and destination servers. I'm guessing the issue is to do with the amount of time it takes to complete the backups of these databases, and/or the size of the backup files required to complete these backups. Changing the backup destination to local storage works fine (and very, very fast in comparison). From the Job History, I can find a few hints as to what the problem could be... Code: 0xC002F210 (Always this code, but a mix of the following descriptions...) "The operating system returned the error '64(failed to retrieve text for this error. Reason: 1815)' while attempting 'SetEndOfFile' on '\drserver\SQLBackups\Database.bak'. BACKUP DATABASE is terminating abnormally. "The operating system returned the error '64(failed to retrieve text for this error. Reason: 1815)' while attempting 'FlushFileBuffers' on '\drserver\SQLBackups\Database.bak'. BACKUP DATABASE is terminating abnormally. Please help save my hair and sanity!!

  Read the article

• Can I have damaged a CPU ?

  - by Pascal

  Hey guys, This is a question I asked on Anantech forums, but I just discovered this community and think this question would fit right in. Here goes: I built a PC around a Q9550 1 1/2 years ago (MoBo is an Asus P5Q deluxe). Specs give 2.83GHz, OC'ed it to 3.40 GHZ without any problem (or so I thought) till 2 months ago. Cooling is provided by stock Intel Fan... 2 Months ago, I began to see random crashes, bios saying CPU overheat error... PC would reboot at OC'ed speed without any problem. Since last saturday and a few more crashes, PC won't reboot at 3.40 GHz, and even at stock speed (2.83 GHz), I got core temperatures of (60 C idle, 95 C under load) on the first two cores. This is the 4 core temperatures I am talking about, not the T-CPU which obvioulsy is lower. Fan is running at a steady 2000 RPM. Questions for you : 1. Is 2000 RPM the normal speed of the Intel fan or is my fan somehow broken (which could explain the overheating). In this case, any recommendation for a good fan for OCing ? 2. Hypothesis I fear is the right one: can the CPU have been slowly damaged over time by this OCing, meaning there is nothing much to do except waiting for it to die ? (As a side note, I am surprised that the 9550 is still around 300 $CDN here... Thought it would have been cheaper with all those i3/i5/i7 around). Any help or advice would be more than welcome...

  Read the article

• Paste textbox from Powerpoint to Word as an editable control

  - by George Harris

  I have a Powerpoint 2007 file that contains a number of textboxes and shapes with text on them. I can edit, resize, change the text, etc. in these boxes in Powerpoint. However, if I select an item, copy it, and paste it into a Word 2007 document, I can't edit it. I can resize the entire thing, but it acts more like an image than a text box. I've tried the paste special options and keep source formatting options, but still can't edit it. Is there a way to be able to paste the editable content from Powerpoint and still have it editable in Word? Update I found this question that appears to get to the root of the problem: The MS Office Art graphics engine (aka Escher 2) is new to MS Office 2007 and while fully implemented in Excel and Powerpoint is only partially implemented in Word 2007 for backwards compatibility with the MS Office Drawing/Graphics engine (aka Escher) still available in Word It should work in earlier versions of Word and Word 2010, but not Word 2007. This is quite frustrating as I have to edit the slide in Powerpoint before copying it into Word. While doable, it adds another step, but the problem is that everyone who wants to update the Word document will have to do the same thing, adding complexity and steps for everyone. If I embed the Powerpoint slide in the document, I can edit the controls, but they don't scale the same way and takes a lot of work.

  Read the article

• Regular Windows 7 BSOD with Shrew VPN client

  - by Junto

  The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

  Read the article

• Domino nchronos.exe multiple instances causing server to die, and Sametime problems

  - by Kevin

  I've had this problem for a few months now. I thought it started when I installed the Traveller software on the server to add ActiveSync support, but I removed that and the problem still persists. Basically new instances of "nchronos.exe" keeps spawning (and not ending), so over a period of a few days the server eventually gets drowned in nchronos.exe processes, stops responding and I need to kill Domino. My process count the last time was up at about 330, and when I killed it and restarted the Domino my process count went to 160. I'm running Domino 8.5.1 with Fix Pack 2. I don't know if it's relevant, but my Domino server was also acting as a Sametime server. At around the same time that nchronos started playing up sametime also stopped working. None of my users can connect to sametime and in the domino log it keeps telling me "stpolicy.exe" has terminated. I've googled for that and tried a few things, but nothing seems to make sametime work again. Any thoughts?? Cheers, Kevin

  Read the article

• Haproxy and CNAME

  - by user123354

  I want to create a simple load balancer for the two servers. The problem is with CNAME records, I think. Let's say I have two the same applications on AppFog.com. app1.aws.af.cm and app2.aws.af.cm Here is my haproxy.cfg file: global maxconn 2000 daemon defaults mode http clitimeout 60000 srvtimeout 30000 contimeout 4000 option httpclose listen http_proxy bind [myip]:80 mode http stats enable stats auth user:passwd stats uri /stats balance source option httpchk option forwardfor server host01 app1.aws.af.cm:80 maxconn 300 check server host02 app2.aws.af.cm:80 maxconn 300 check But this only resolving IP for domain app1.aws.af.cm and app2.aws.af.cm, which obviously doesn't work if I open this IP in web browser. The problem is that AppFog doesn't have public IP for application (same as OpenShift). How to do that Haproxy to perform a proper connection between Load Balancer and this two servers? Example: This is real app - http://freechat.eu01.aws.af.cm Haproxy only resolves IP for this domain which is 46.51.204.8:80 Of course this IP will not show my application, only an error page. Sorry for my poor English.

  Read the article

• Access router set up as a bridge behind another router

  - by Alari Truuts

  I have a problem my ISP is refusing to help me with, even though they put up the whole system. Specifications: There's a Thomson TG784 router through which the internet comes in to the building, Behind that (for some reason) is a Juniper NetScreen 5XT - 105 Firewall/Router? which leads to an AMX nxa-enet24 switch that carries the connections all over the building and a series of Apple AirPorts for wifi. Problem: The first router (Thomson) is required for ipTV (by Elion). The tv or ipTV box has to be connected straight to the Thomson router. My service provider cannot see the Thomson router from their side, but see the Juniper, so we might think the Thomson has been configured as a bridge. I need a way to access the Thomson router and see it's configurations, because currently, when connecting a Samsung tv to that router (with elion app for ipTV viewing) or even a computer, it cannot access the internet and even if it could, it would update the Thomson router software, losing it's configurations which I need to preserve. I'm unable to find out the Thomson routers ip address to connect to it, and when directly conencting with a cat5 cable, it doesn't give me an ip address. Hope someone can show me the correct direction for solving my issue. Thank you all for reading, and I appreciate any help, Alari Truuts

  Read the article

< Previous Page | 731 732 733 734 735 736 737 738 739 740 741 742  | Next Page >