Search Results

Search found 45715 results on 1829 pages for 'system verilog'.

Page 741/1829 | < Previous Page | 737 738 739 740 741 742 743 744 745 746 747 748  | Next Page >

• Missing MB on a GPT partioned SSD

  - by pisswillis

  I recently installed Arch Linux on an Intel 40GB SSD. I used GPT for partioning (via GNU parted) and created the following partions: /dev/sda1 : 1 MB, no FS, flag=bios_grub /dev/sda2 : 30MB, /boot, ext2, flag=boot /dev/sda3 : 20GB, /home, ext4 /dev/sda4 : ~20GB, /, ext4 After struggling to install grub2 from the livecd environment (which I finally did via grub-install /dev/sda --root-directory=/mnt/ --no-floppy --force) I got a working system. However, when I was inspecting disk usage with df I noticed that my home partition had around 170MB of used space on it. This surprised me because the only things on /home were one users .bashrc, .bash_history, and .lesshst. du confirmed that there was only a few KB of space being used on /home. Why does df report approximately 170MB being used when du does not? Is this space "gone forever", or can I regain it by repartioning and/or reinstalling? When I installed grub2 it said something along the lines of "your embed area is too small", and that I could "use BLOCKLISTS, but BLOCKLISTS are UNRELIABLE". In the end the only way I could get a system booting from the SSD was to use blocklists via the grub-install --force flag. Is this related to the mysterious missing 170MB? Thanks

  Read the article

• How does one skip "Windows did not shut down successfully" in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• How can I format an SD card with a more robust Linux-usable filesystem with a specific cluster size for better write performace?

  - by Harvey

  Goal: microSD card formatted... for best write performance for use only with embedded Linux for better reliability (random power failures may occur) using an 64kB cluster size I'm using an 8GB microSD card for data storage inside an embedded Linux/ARM device. The SD card is not removable. I've been using ext3 instead of the pre-installed FAT32 because it seems to better handle random power failures during writes. However, I kept noticing that my write performance is always best with the pre-installed FAT32 from Kingston. If I reformat the card with FAT32, the performance still suffers. After browsing wikipedia, I stumbled upon the following comment saying that some cards are optimized for specific cluster sizes. In my case, the Kingston comes pre-formatted for an 64kB cluster size. Risks of reformatting Reformatting an SD card with a different file system, or even with the same one, may make the card slower, or shorten its lifespan. Some cards use wear leveling, in which frequently modified blocks are mapped to different portions of memory at different times, and some wear-leveling algorithms are designed for the access patterns typical of the file allocation table on a FAT16 or FAT32 device.[60] In addition, the preformatted file system may use a cluster size that matches the erase region of the physical memory on the card; reformatting may change the cluster size and make writes less efficient.

  Read the article

• How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

  - by Software Monkey

  I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

  Read the article

• What's needed in a complete ASP.NET environment?

  - by Christian W

  We have a ASP3.0 application with a few ASP.NET (2.0) dittys mixed in. (Our longtime goal is to migrate everything to ASP.NET but that's not important for this issue) Our current test/deploy workflow is like this: 1 Use notepad++ or VS2008 to fix a bug/feature (depending on what I have open) 2 Open my virtual test-server 3 Copy the fixed file over, either with explorer, or if I can be bothered to open it, WinMerge 4 Test that the fix works 5 Close the virtual test-server 6 Connect to our host with VPN 7 Use WinMerge to update the files necessary 8 Pray to higher powers that the production environment is not so different that something bombs. To make things worse, only I have access to my "test-server". So I'm the only one testing it. I really want to make this a bit more robust, I even have a subversion setup running. But I always forget to commit changes... And I don't even work in my checked out folder, but a copy of what is currently in production... Can someone recommend some good reading on deploying, testing, staging and stuff like that. I currently use VS2008 and want to use subversion or GIT (or any other free VCS). Since I'm the only developer, teamsystem is not really an option (cost-related). I have found myself developing an "improved" feature, only to find a bug in the same feature in the production system. And since my "improved" feature incorporated deleting some old functionality, I have to fix bugs directly in production... That's not a fun feeling... (I have inherited this system recently... So it's not directly my fault that it is like this ;) )

  Read the article

• How to organise storage for media content such as video and music?

  - by thor

  Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

  Read the article

• Evernote from vim

  - by juanpablo

  I search a way to edit evernote notes from vim I begin with this #!/bin/bash evernoteDir="$HOME/Library/Application*Support/Evernote/data" dataDir=$(ls -trlh $evernoteDir| tail -n 1| awk '{print $NF}') contentDir="$evernoteDir/$dataDir/content" file=$(ls -trlh $contentDir | tail -n 1| awk '{print $NF}') vim -c 's/div>/div>\r/g' $contentDir/$file/content.html https://gist.github.com/1256416 or maybe create a vim plugin for this ... you have any suggestion? EDIT: for a more simple edition of the evernote note in html format, I make this vim function " Markup function {{{ fun! MkdToHtml() "{{{ " markdown to html silent! execute '%s/ $/<br\/>/g' silent! execute '%s/\*\*\(.*\)\*\*/<b>\1<\/b>/g' silent! execute '%s/\t*###\(.*\)/<H3>\1<\/H3>/g' endf "}}} command! -complete=command MkdToHtml call MkdToHtml() nn <silent> <leader>mm :MkdToHtml<CR> " }}} and a vim function for open the last note edited fun! LastEvernote() "{{{ " a better solution is with evernote api let evernoteDir=expand("$HOME")."/Library/Application*Support/Evernote/data" let dataDir=system("ls -trlh ".evernoteDir."| tail -n 1| awk '{print $NF}'") let contentDir=evernoteDir."/".dataDir."/content" let contentDir=substitute(contentDir,"\n","",'g') let note=system("ls -trlh ".contentDir." | tail -n 1| awk '{print $NF}'") let note=substitute(note,"\n","",'g') sil! exec 'sp '.contentDir.'/'.note.'/content.html' sil! exec '1s/>/>\r/g' sil! exec '%s/<br.*\/>/<br\/>\r/g' sil! exec '%s/<\//\r<\//g' sil! exec 'g/^\s*$/d' normal gg sil! exec '1,4fo' sil! exec '$-1,$fo' endf https://gist.github.com/1289727

  Read the article

• Oracle Database Recovery Problem

  - by Palani

  I am very new to Oracle, and trying to restore a oracle 8i database on win 2000 server. I have one week old database backup (backup taken with exp command), and i want to restore it now. Now I am unable to login through sqlplus (got shutdown in progress error) I have a backup and i want to restore it, but oracle is not starting at all, and 'imp' command is failing. I started sqlplus / as sysdba and following is the log of what i am trying to do. Can some one guide me further. SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup mount; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. SQL> alter database open; alter database open * ERROR at line 1: ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01245: offline file 1 will be lost if RESETLOGS is done ORA-01110: data file 1: 'C:\ORACLE\ORADATA\ABCD\SYSTEM01.DBF'

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• 2560 x 1600 screen resolution not available when a second monitor is attached.

  - by sgmoore

  I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

  Read the article

• How to make Synaptics touchpad work better on Linux?

  - by whitequark

  I have Debian Squeeze currently installed on a Samsung N250 netbook with a Synaptics touchpad. These touchpads are, generally, good, and everything works perfectly on Windows. The support is extremely sucky on Linux through. Of course it has all the cool features like two-finger scrolling, but the cursor (or whatever is a replacement for cursor when scrolling) is trembling awfully. It trembles when I just keep the finger on touchpad, it shakes awfully if the finger is close to the top of touchpad, and when I'm scrolling with it (no matter with two fingers or one), the page shakes a lot too. None of this behavior is observed even in Windows XP with just the default drivers installed. Here's the Xorg version: $ Xorg -version X.Org X Server 1.7.7 Release Date: 2010-05-04 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.32-5-686 i686 Debian Current Operating System: Linux mannaz 2.6.32-5-686 #1 SMP Fri Dec 10 16:12:40 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/mannaz-root ro quiet splash Build Date: 02 December 2010 01:08:37AM xorg-server 2:1.7.7-10 (Julien Cristau <[email protected]>) Current version of pixman: 0.16.4 and here is synclient -l output: http://pastebin.com/Eqa6hGXP

  Read the article

• Overriding HOMEDRIVE and HOMEPATH as a Windows 7 user

  - by MikeC

  My employer has an Active Directory group policy which sets my Windows 7 laptop HOMEDRIVE to "M:" (a mapped network drive) and my HOMEPATH to "\". Since I have read-only permissions for the root of that shared drive, I cannot create files or directories in my windows home directory. My attempts to work with the IT department have been unsuccessful. Is there a way for me to globally change these envars at boot or login time? I need for all applications to use alternate values (such as "C:" and "\Users\myname"). I have some installed utilities (like gvim and others) that store preference files in the user's home directory. IMPORTANT: Changing these envars under "System Properties Environment Variables" does not work. I have tried setting these as both User and System Variables (including a reboot). TypingSET HOMEin a DOS window clearly shows that my settings are ignored. Also, using "Start in" in a Windows shortcut will also not solve this, as I need things like Explorer context menu items (like "Edit with Vim") to operate correctly. I do have admin rights on this company laptop, but I am not a Win7 guru. Back in the day, a boot script would have solved this in a minute. Is it even possible today? Thanks.

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• Virtual host redirects to localhost in Ubuntu

  - by Salman

  I have recently configured Virtual Host in my Ubuntu 11.10. But whatever site i type, it always redirects to the localhost page. This is my "our-test-site" file: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/zftut/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/zftut/public/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> and this is my, "etc/hosts" file: 127.0.0.1 localhost 127.0.0.1 our-test-site.local 127.0.0.1 zftut.local 127.0.1.1 System.B System Now when I try to go for "zftut.local", it redirects me to localhost page, showing me this: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. What am I doing wrong? I refered "this" tutorial for setting up virtual host.

  Read the article

• SSD/HDD not exceeding 120 MB/s

  - by skiwi

  SO here is the situation: First this was my old PC, it had a 2x 1TB RAID 0 and a Corsair Force 3 SSD in it. This were the old speeds, measured by HDTune Pro. 2x 1TB RAID 0: Corsair Force 3 SSD Then my dad got my PC and we had several issues, in the end turned out both RAID and SSD controller were malfunctioning causing BlueScreens on 100% load. Removed the RAID 0, but leaving the HDD's intact and bought an Samsung 840 EVO 120GB, though the Corsair SSD is still in the system, just not as sytem disk anymore. 1TB HDD (one of them): Corsair SSD: Samsung SSD: We did not assemble the PC ourselves, so answering some technical questions might be more difficult, though we will do our best. First thing we noticed is that the Samsung 840 EVO is no where reaching it's advertised speed, even an Samsung 840 250GB (non-EVO) is reaching 350 MB/s in my own PC. Then we noticed that both SSD's are capped at 120 MB/s exactly, not sure if this is being caused by HDTune Pro, but very unlikely. And even worse, the Corsair Forza 3 was running faster before the system got reassembled. Does anyone have any clue what is going on?

  Read the article

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• Multiple *NIX Accounts with Identical UID

  - by Tim

  I am curious whether there is a standard expected behavior and whether it is considered bad practice when creating more than one account on Linux/Unix that have the same UID. I've done some testing on RHEL5 with this and it behaved as I expected, but I don't know if I'm tempting fate using this trick. As an example, let's say I have two accounts with the same IDs: a1:$1$4zIl1:5000:5000::/home/a1:/bin/bash a2:$1$bmh92:5000:5000::/home/a2:/bin/bash What this means is: I can log in to each account using its own password. Files I create will have the same UID. Tools such as "ls -l" will list the UID as the first entry in the file (a1 in this case). I avoid any permissions or ownership problems between the two accounts because they are really the same user. I get login auditing for each account, so I have better granularity into tracking what is happening on the system. So my questions are: Is this ability designed or is it just the way it happens to work? Is this going to be consistent across *nix variants? Is this accepted practice? Are there unintended consequences to this practice? Note, the idea here is to use this for system accounts and not normal user accounts.

  Read the article

• big cpu load on vmware server / linux

  - by dezfafara

  Hi, I currently using a server 2.x hosting 4 virtual machines on a linux system Today, on my physical server, I saw an enormous load average: this is the "top" of the server, illustrating my 4 virtual guests. top - 11:02:02 up 194 days, 23:09, 5 users, load average: 18.78, 12.05, 13.55 Tasks: 113 total, 4 running, 109 sleeping, 0 stopped, 0 zombie Cpu0 : 71.6%us, 19.0%sy, 0.0%ni, 8.8%id, 0.0%wa, 0.3%hi, 0.3%si, 0.0%st Cpu1 : 74.3%us, 10.4%sy, 0.0%ni, 15.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 72.5%us, 17.6%sy, 0.0%ni, 9.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 79.5%us, 4.6%sy, 0.0%ni, 16.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8178884k total, 8129980k used, 48904k free, 134904k buffers Swap: 10490436k total, 148k used, 10490288k free, 6129728k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7312 root 6 -10 1149m 921m 559m R 97 11.5 107947:09 vmware-vmx 6995 root 6 -10 779m 687m 317m R 92 8.6 107374:31 vmware-vmx 6693 root 6 -10 880m 659m 409m S 85 8.3 76947:33 vmware-vmx 12937 root 6 -10 960m 719m 523m S 75 9.0 67219:49 vmware-vmx In bold are the cpu usage for my 4 virtuals guests These guests are running on a linux system, and the appropriate process are usually 5% - 15% of cpu I don't understang why , since a few days I have this big problem. This is the "top" on a virtual guest which is at 95% of cpu load top - 11:23:15 up 194 days, 23:13, 4 users, load average: 0.25, 0.47, 0.59 Tasks: 92 total, 2 running, 90 sleeping, 0 stopped, 0 zombie Cpu(s): 1.4%us, 7.7%sy, 0.0%ni, 90.5%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 382296k total, 369732k used, 12564k free, 145156k buffers Swap: 979924k total, 13956k used, 965968k free, 86988k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3691 root 20 0 23948 1148 960 S 13.0 0.3 15339:23 vmware-guestd 3840 root 20 0 19880 584 512 S 7.7 0.2 1729:17 hald-addon-stor This virtual guest state is ok ... If anyone has any ideas .. Thanks

  Read the article

• Computer Freezes with "Bugcheck 0" on Windows 7. How do I figure out why?

  - by George Stocker

  After about 10 minutes of running, my computer will hang, exhibiting the following symptoms: Both monitors act as if there is no image being sent to them (on, but blacked out) The CAPS Lock key on the keyboard will not respond. The computer appears to still be running: CPU Fan is whirring. When I reboot, Windows says "The previous shutdown was unexpected." I've enabled the 'don't automatically restart' on an error, and asked the computer to make a memory dump whenever it crashes, but it hasn't done either. The problem is that there's no bugcheck for me to go off of, so there's no way for me to determine what the cause is (I think). Here are my system specs: Intel Core 2 Duo E6750 Gigabyte P35C-DS3R w/ 4.00 GB (DDR2 Ram) Nvidia 8800 GT Windows 7 I've tried running the Windows Memory checker, but the system also freezes when using that after about 10 minutes as well. How can I diagnose the problem with no bugcheck and no ability to run a memory checker? Update Running Memtest86 also causes the computer to crash (looks like it doesn't make it through a full pass - it was only running for about 10 minutes when the PC stopped responding).

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Getting prompted for password accessing page through script even when client and server are in same

  - by Munawar

  I'm trying to pull up an internal webpage in automated fashion using the methods in 'Internetexplorer.Application' using vbscript. But I'm getting prompted for password, although the client and the server both are in the same domain. Predictably when I manually try to access the web page, I don't have any problem. Only when I try using cscript.exe or iexplore.exe, I get prompted. I'm trying to automate some of the smoke test we do after a new build is deployed. But this password prompt is getting in the way. Following are the system specs Client machine - IE 7.0, OS is Windows server 2003 Server machine - Windows Server 2008 Both are in the same domain. So far I've unsuccessfully tried following to automate the password input system.diagnostics.process.start var WinHttpReq = new ActiveXObject("WinHttp.WinHttpRequest.5.1"); WinHttpReq.Open("GET", "http://website", false); WinHttpReq.SetCredentials("username", "password", 0); Nothing seems to work I checked in IIS. we have only anonymous and forms authentication enabled Is there any configuration setting in the client machine that can be tweaked to bypass this, although I'd hate to do it since you step on the toes of twenty people trying to do that. Preferable way would be to programmatically input it if its possible. Also, if you can suggest a more appropriate forum, that'd be great too. Please help.

  Read the article

• SNMP Access on Ubuntu

  - by javano

  I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• Manipulating IIS7 Configuration with Powershell

  - by John Price

  I'm trying to script some IIS7 setup tasks in PowerShell using the WebAdministration module. I'm good with setting simple properties, but am having some trouble when it comes to dealing with collections of elements in the config files. As an immediate, example, I want to have application pools recycle on a given schedule, and the schedule is a collection of times. When I set this up via the IIS management console, the relevant config section looks like this: <add name="CVSupportAppPool"> <recycling> <periodicRestart memory="1024" time="00:00:00"> <schedule> <clear /> <add value="03:31:00" /> </schedule> </periodicRestart> </recycling> </add> In my script I would like to be able to accomplish the same thing, and I have the following two lines: #clear any pre-existing schedule Clear-WebConfiguration "/system.applicationHost/applicationPools/add[@name='$($appPool.Name)']/recycling/periodicRestart/schedule" #add the new schedule Add-WebConfiguration "/system.applicationHost/applicationPools/add[@name='$($appPool.Name)']/recycling/periodicRestart/schedule" -value (New-TimeSpan -h 3 -m 31) That does almost the same thing, but the resulting XML lacks the <clear/> element that is created with via the GUI, which I believe is necessary to avoid inheriting any default values. This sort of collection (with "add", "remove", and "clear" elements) seems to be fairly standard in the config files, but I can't seem to find any good documentation on how to interact with them consistently.

  Read the article

< Previous Page | 737 738 739 740 741 742 743 744 745 746 747 748  | Next Page >