Search Results

Search found 21307 results on 853 pages for 'image capture'.

Page 753/853 | < Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >

• VMWare ESXi 5 - Expanded RAID 5 array - cannot access datastore

  - by Dayton Brown

  I'm using VMWare ESXi 5 and had a 2 TB RAID 5 setup on an HP DL360 with a P400i RAID card. I added two more 1 TB drives and using the SmartStart ACU, added the drives and expanded the logical disk. Now after booting back to ESXi, the server boots, but lists no available persistent storage. I've rescanned multiple times to no avail: the Datastore doesn't show up. I booted to GParted and the 1.8TB partition shows up, but it shows as unknown. Anyone have any good ideas? EDIT: Final Solution So after much gnashing of teeth, it was fairly simple to solve. I purchased an eSata 2 TB external drive and a PCI eSata card for my server. I then used Clonezilla to image the current partitions to my new external drive. You have to check "don't check drive sizes" in advanced mode, otherwise it will yell at you for have a smaller drive. For some reason my PCI card wouldn't boot on my HP server, so I hooked the drive up to another desktop I had, booted to VMWare, and copied the vmdk's to another drive. I'm going to blow out the RAID config and then create 1.5TB logical drives.

  Read the article

• Ubuntu 10.04->10.10 in failed state - how to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: (1) "Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a)." (2) "gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok]" (3) "gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ..." What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• 32bit dll not loading with Enable 32 Bit Applications on IIS 7.5

  - by Jon

  I have a MVC 3 Web Site referencing a 32 bit DLL. The OS is Windows 2008 R2 x64. The website is in the ASP.NET 4 App Pool. I have turned on Enable32Bit but it doesn't work. I get a Bad Image Exception but can't find out to turn this level of logging on in IIS. I have setup up a page that outputs whether it's running 32bit or 64bit and when I turn on/off the Enable32Bit on the AppPool I get the correct output. The website is also in Full Trust. I'm at a loss to try and and get it to work. I do know that it works on Win7 32bit. Can you suggest some things to try? UPDATE: I have just written a simple Windows Forms App with a button on it which calls my DLL. This was built with target of x86 and it worked fine so there is an issue with IIS or ASP.Net I think. UPDATE 2: Does it matter if the ASP.Net Pipeline is Clasic or Integrated? I've tried both but same problem but thought it was worth asking UPDATE 3: I found this question trying to do the same thing and he gave up which isnt too helpful!!

  Read the article

• domain user disabling screensaver

  - by RASG

  I have the following situation: Due to security reasons the screensaver is activated after 10 minutes, and immediately locks the screen. There are GPOs preventing the user from changing the screensaver parameters and the background image. In order to bypass the background policy, some users are using bginfo The problem is that for some reason now the screensaver doesn't work anymore. The settings are still the same (10 minutes; locked to the user) and comparing snapshots of the registry before and after executing bginfo doesn't show any significant modification. Any hints? EDIT 1: Ok, i figured whats going on, but now i have another question. bginfo refreshes the user settings by reading HKEY_CURRENT_USER\Control Panel\Desktop, which has ScreenSaveActive. If the user set it to 0, disables the screensaver. Why isnt HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Control Panel\Desktop, which sets ScreenSaveActive to 1, being enforced? or if it is being enforced, where is bginfo storing the value 0, and how can it bypass the policy? EDIT 2: I also discovered that after setting any value to HKEY_CURRENT_USER\Control Panel\Desktop\ScreenSaveActive, it can be deleted and the last value will remain active. For some reason HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Control Panel\Desktop\ScreenSaveActive value is not being enforced to the user.

  Read the article

• What is causing ocassional white windows on my Mac?

  - by user63333

  Hello. I'm having a very strange problem with my Mac lately. When I'm working in an app and a new window pane or sheet is displayed, sometimes it comes up completely white. Once an app is having these problems, it will continue to bring up a blank screen for that particular window (although other windows work fine). After the app is relaunched, the window is fine again. What I'm noticing that's very strange is that although the interface turns completely white, the functions of the interface are still available. So I have to "navigate blindly" around the interface, until I can relaunch. This occurs throughout the operating system. Screenshots: This is what happened when I tried opening the File menu in Lightroom app. What happened to me on Lynda.com (in Firefox) after selecting the "Software..." dropdown. (All other dropdowns were fine. Reloading the page fixed it.) When I was decompressing a file, The Unarchiver launched and opened this white window. It still decompressed the file. This is what happened one time when I opened Finder (with TotalFinder) to my Downloads folder. This is something I've never seen before. This just started happening lately. What could be the problem? Thanks for your help. NOTE: since new users are not allowed to post images, just image blank white interface elements. And since new users also aren't allowed to post more than one link, here's the first screenshot:

  Read the article

• Unexpected(?) high 'wasted' memory in memcached

  - by Nanne

  Looking at our memcached stats I think I have found an issue I was not aware of before. It seems that we have a strangely high amount of wasted space. I checked with phpmemcacheadmin for a change, and found this image staring at me: Now I was under the impression that the worst-case scenario would be that there is 50% waste, although I am the first to admit not knowing all the details. I have read - amongst others- this page which is indeed somewhat old, but so is our version of memcached. I think I do understand how the system works (e.g.) I believe, but I have a hard time understanding how we could get to 76% wasted space. The eviction rate that phpmemcacheadmin shows is 2 ev/s, so there is some problem here. The primary question is: what can I do to fix this. I could throw more memory at it (there is some extra available I think), maybe I should fiddle with the slab config (is that even possible with this version?), maybe there are other options? Upgrading the memcached version is not a quickly available option. The secondairy question, out of curiosity, is of course if the rate of 75% (and rising) wasted space is expected, and if so, why. System: This is currently not something I can do anything about, I know the memcached version isn't the newest, but these are the cards I've been dealt. Memcached 1.4.5 Apache 2.2.17 PHP 5.3.5

  Read the article

• Dialog box tells me there's a missing driver when installing 64-bit version of Windows 7

  - by Eikern

  I'm trying to install Windows 7 64-bit on my computer (ASUS P6T Deluxe V2, one 80GB HDD and two 1 TB HDDs). When I'm supposed to select whether I want to Upgrade or do a Custom install, I get a dialog box telling me: Load Driver A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step. I've tried to reach this step using a 32-bit installation disc, but that doesn't generate this message at all. Through the command windows (shift-F10) I can reach all of my drives, including my optical drive, without any problems--so what kind of device driver is it the installation wants? I've tried all the obvious drivers on the CD that followed my motherboard, but I can't seem to find the right one. The problem is that I don't know what device I'm supposed to load the drivers for in the first place. Can anyone help me? Edit: It turned out that my downloaded image was corrupted. I borrowed a DVD from a friend of mine, which worked!

  Read the article

• Preserve embedded album art when converting from .flac to .ogg

  - by Profpatsch

  I want to convert my archived .flac library to .ogg for daily use. Using find ./ -iname '*.flac' -print0 | xargs -0 -n1 oggenc -q6 on the root music folder and then deleting every .flac (having copies of them in archive) seems straight forward, after trying it with one file it worked and all of the tags were transfered, too, except for one: Embedded album art! I always prefer emedded covers over folder images, since I have some albums with varying covers. One possible solution is discussed here, but the script only works if the image is already extracted: Embed album art in OGG through command line in linux One possible solution I thought about was extracting album art from every song (not every song has one, though, and some even 2 or 3!), temporarily saving it and then using the script to include it into the finished .ogg. But then I want to increase the number of processes xargs runs simultaniously to save time, so the temp images need to have a distinct name. Is there a (linux) program that knows how to handle this? Or is there a finished script floating around somewhere? It would be nice if oggenc supported adding embedded coverart and it really is a shame, since these two formats should (in theory) share the same tag format. Edit: 15 days and noone even tries to answer. It’s funny, most of my questions don’t get answered. Too hard? Wrong SE site?

  Read the article

• Debian Wheezy 7.5 64bit xfce4 install error ( no desktop environment installed already )

  - by GeoMind

  i wrote a CD with an iso-image from debian.org. the debian-7.5.0-amd64-CD-1.iso from this folder. Debian Wheezy 7.5 stable 64bit There was an error at Select and install software step. It said Retrieving file 770 from 800 and then it failed the installation. I continued the instal and when i opened the computer it doesn't work the Ctrl + Alt + F7 as i waited. It starts at tty1 and after logging in i edited config file cause it had a lot of errors and said E: Unable to correct problems, you have held broken packages or Couldn't found the package. FILE: /etc/apt/sources.list # deb cdrom:[Debian GNU/Linux 7.5.0 _Wheezy_ - Official amd64 CD Binary-1 20140426-13:37]/ wheezy main #deb cdrom:[Debian GNU/Linux 7.5.0 _Wheezy_ - Official amd64 CD Binary-1 20140426-13:37]/ wheezy main deb http://security.debian.org/ wheezy/updates main contrib non-free deb-src http://security.debian.org/ wheezy/updates main contrib non-free deb http://ftp.us.debian.org/debian/ squeeze main contrib non-free deb-src http://ftp.us.debian.org/debian/ squeeze main contrib non-free After that i tried to install xfce4 as desktop environment. Guide found at Linux Panda But it print at terminal: What i sould do? How i can fix this problem?

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• Intermittent Trouble Entering Hibernate on WinXP

  - by kquinn

  My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

  Read the article

• How do I permanently delete /var/log/lastlog?

  - by GregB

  My /var/log/lastlog file is huge. I know it's really only a few kilobytes, but tar isn't smart enough to know that, so when I image a virtual machine, my restore fails because it thinks I'm trying to load more data than I have capacity on my disk. I want to delete /var/log/lastlog and stop any and all logging to the file. I'm aware of the security implications. This logging needs to stop to preserve my backup strategy. I've made a change to /etc/pam.d/login which I was told would disable logging to /var/log/lastlog, but it does not appear to work as /var/log/lastlog keeps growing. # Prints the last login info upon succesful login # (Replaces the `LASTLOG_ENAB' option from login.defs) #session optional pam_lastlog.so Any ideas? EDIT For anyone interested, I use Centrify Express to authenticate my users via LDAP. Centrify Express is "free", but one of the drawbacks is that I can't manage user UIDs via LDAP, so they are given a dynamic UID when they login to a server. Centrify picks some crazy high UID values (so they don't conflict with local users on the server, presumably). /var/log/lastlog is indexed by UID, and grows to accommodate the largest UID on the system. This means that when a Centrify user logs in, they get a UID in the upper-end of the UID range, which causes lastlog to allocate an obscene amount of space, according to the file system. ~$ ll /var/log/lastlog -rw-rw-r-- 1 root root 291487675780 Apr 10 16:37 /var/log/lastlog ~$ du -h /var/log/lastlog 20K /var/log/lastlog More Into --- Sparse Files

  Read the article

• VirtualBox how to merge arbitrary snapshot into base vdi

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID? Thanks

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

• Execute encrypted files but don't let anybody read them.

  - by Stebi

  I want to provide a virtual machine image with an installed web application. The user should be able to boot the vm (don't login, just boot) and a webserver should start automatically. The point is I want to hide the (ruby) source code of the web application from everyone as there is no obfuscator for ruby. I thought I could use file system encryption to encrypt the directory with the sourcecode (or even a whole partition). But the webserver user must be able to read it automatically after booting. Nobody is allowed to login as the webserver user (or any other user) so no other can read the contents. My questions are now: Is this possible? Because I give away the whole vm everybody could mount its virtual discs and read them (except the encrypted one). Is it now possible to find the key the webserver user needs to decrypt the files and decrypt them manually? Or is it safe to give such a vm away? The problem is that everything needed to decrypt must be included somewhere in the vm else the webserver cannot start automatically. Maybe I'm completely wrong and you have another tip for me securing the source code.

  Read the article

• secure user-authentication in squid: The Story

  - by Isaac

  once upon a time, there was a beautiful warm virtual-jungle in south america, and a squid server lived there. here is an perceptual image of the network: <the Internet> | | A | B Users <---------> [squid-Server] <---> [LDAP-Server] When the Users request access to the Internet, squid ask their name and passport, authenticate them by LDAP and if ldap approved them, then he granted them. Everyone was happy until some sniffers stole passport in path between users and squid [path A]. This disaster happened because squid used Basic-Authentication method. The people of jungle gathered to solve the problem. Some bunnies offered using NTLM of method. Snakes prefered Digest-Authentication while Kerberos recommended by trees. After all, many solution offered by people of jungle and all was confused! The Lion decided to end the situation. He shouted the rules for solutions: Shall the solution be secure! Shall the solution work for most of browsers and softwares (e.g. download softwares) Shall the solution be simple and do not need other huge subsystem (like Samba server) Shall not the method depend on special domain. (e.g. Active Directory) Then, a very resonable-comprehensive-clever solution offered by a monkey, making him the new king of the jungle! can you guess what was the solution? Tip: The path between squid and LDAP is protected by the lion, so the solution have not to secure it. Note: sorry for this boring and messy story! /~\/~\/~\ /\~/~\/~\/~\/~\ ((/~\/~\/~\/~\/~\)) (/~\/~\/~\/~\/~\/~\/~\) (//// ~ ~ \\\\) (\\\\( (0) (0) )////) (\\\\( __\-/__ )////) (\\\( /-\ )///) (\\\( (""""") )///) (\\\( \^^^/ )///) (\\\( )///) (\/~\/~\/~\/) ** (\/~\/~\/) *####* | | **** /| | | |\ \\ _/ | | | | \_ _________// Thanks! (,,)(,,)_(,,)(,,)--------'

  Read the article

• Why doesn't Mail.app properly thread Microsoft Outlook replies?

  - by thepurplepixel

  I use Mail.app 3.6 (on 10.5 Leopard), and I always use plain-text email. Normally, when I receive an email reply from practically anyone, it looks like this (test message sent from Mail.app, replied from Hotmail, replied from Google Apps): Needless to say, I quite like this threading, and it keeps everything very visually-organized. However, when I receive a plain-text email reply from people on Microsoft Outlook (tested with Outlook 2003 & 2007), it isn't threaded like the image. Instead, it appears as below, without being threaded nicely. My reply to the message. -----Original Message----- From: Tyson Moore [mailto:[email protected]] Sent: [Date] To: [Receiver] Subject: Test Original message. Through looking at the source of my original message, it appears as though every time the message is quoted, less-than signs (<) are inserted before every line in the reply. I am assuming this is what triggers the quoting behaviour exhibited by Mail.app, but I'm no expert. My question: is this a Mail.app limitation in not recognizing the -----Original Message----- line put in by Outlook, or an Outlook problem not inserting > before every line in a reply (or both)?

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• ubuntu preseed installation keep missing mirror files

  - by JackWu

  Install ubuntu12.04.2 with preseed file, but there is one buggy problem about preseed mirror setting. The symptom here is installing process got stuck. So I track down the log file, and find out the real problem, the installation is looking for a file that's not there. This is just one of them, another pops up if I faked this file. This all happened during preseed, so I believe preseed has something to do with this. I google ubuntu preseed mirror and find this post saying: # If you select ftp, the mirror/country string does not need to be set. #d-i mirror/protocol string ftp d-i mirror/country string manual d-i mirror/http/hostname string archive.ubuntu.com d-i mirror/http/directory string /ubuntu d-i mirror/http/proxy string # Alternatively: by default, the installer uses CC.archive.ubuntu.com where # CC is the ISO-3166-2 code for the selected country. You can preseed this # so that it does so without asking. #d-i mirror/http/mirror select CC.archive.ubuntu.com # Suite to install. #d-i mirror/suite string lucid # Suite to use for loading installer components (optional). #d-i mirror/udeb/suite string lucid # Components to use for loading installer components (optional). #d-i mirror/udeb/components multiselect main, restricted I wonder the difference between d-i mirror/http/hostname and d-i mirror/http/mirror, I mean they all specify a mirror, right? In my preseed file, this is no d-i mirror/http/mirror, and d-i mirror/http/hostname points to my own repo as you might notice in the previous image. Here is my question: Does preseed fetches file/resource from internet, if I use local repo? Why it's looking for file that's not even there? This has bothered for quite time, many thanks in advance to anyone who might give any help.

  Read the article

• Requests are making it to my app server, but not into node.js -- why?

  - by Zane Claes

  I detailed in this question on StackOverflow how some random requests are not making it from the client to my Node.js app server, resulting in a gateway timeout. In summary, identical requests are, at random, not even making it far enough to trigger a console.log() in my first line of express middleware. I need to narrow down the problem, though, to find out WHERE the traffic is being lost and it was suggested that I try a packet sniffer on my app servers. Here's my setup: 2x Load Balancers (m1.larges) 2x node.js servers (also m1.large) Here's what's interesting/unusual: the node.js servers started as PHP servers with an Apache stack and continue to serve PHP files for my domain (streamified.me). However, I use a little httpd.conf magic on the app servers so that requests to api.streamified.me get routed over port 8888 to the node.js server: RewriteCond %{HTTP_HOST} ^api.streamified.me RewriteRule ^(.*) http://localhost:8888$1 [P] So, the request hits the load balancer = goes to an app server = gets routed to port 8888 if it's intended for the API = gets handled by node.js So, in the same httpd.conf file, I turned on RewriteLogLevel 5 and then created a simple PHP+CURL script on my localhost to hit my api.streamified.me with a random URL (which should cause node.js to trigger a simple "not found" response) until it resulted in a Gateway timeout. Here, you can see that it has happened -- and the rewrite log shows that the request was definitely received by the app server and forwarded to port 8888... but it was never received by node.js (or, at least, the first line of code in the first line of middleware never gets it...) Image Link: http://i.stack.imgur.com/3OQxS.png

  Read the article

• Is Hyper-V server suitable as a desktop testbench?

  - by Thomas.Winsnes

  At the moment we are running a test bench with several desktop computers, that are reimaged every time we need to test on a different operation system. Also because different versions of our software is tested on each image, we have to install our software every time we want to test it. The problem we have had with going with a virtualization technology is that our software is depending on directx/opengl and 3D acceleration, and this has not been something that virtual machines have excelled at. With the release of SP1 for Windows 7 and Server 2008 R2 Hyper-V has gotten better 3D acceleration support, so we are looking into virtualizing our testbench using this. Our test scenario would most likely be something close to this: 1. Remote into the hyper-V server and load the test VM needed for the current tests 2. Remote into the VM and install the new version of the software 3. Run the tests It would be nice, but not essential, if our support team could remote into the VMs to match the users OS+software combination when doing support. Does anyone have any experience with this kind of settup with hyper-v?

  Read the article

• Why is REMOTE_ADDR only sometimes available as an Apache environment variable?

  - by Xiong Chiamiov

  To avoid having to parse X-Forwarded-For in Varnish, I'm trying to just set a header on the SSL terminator (currently Apache) that stores the direct client IP in a header. On our development machine, this works: RequestHeader set X-Foo %{REMOTE_ADDR}e However, in staging it doesn't. Specifically, the header is empty, as illustrated by both varnishlog: 13 TxHeader b X-Foo: (null) (On the development machine, this shows the IP address as expected.) Similarly, logging REMOTE_ADDR shows that it only appears to be populated on the dev machine: # Config LogFormat "%{X-Forwarded-For}i %{REMOTE_ADDR}e" combined CustomLog "/var/log/httpd/access_log" combined # Log file, staging <my ip> - # Log file, development <my ip> <my ip> Since the dev machine is, well, a dev machine, it is different in a number of ways; however, I can't track down which difference is causing this. The versions of Apache are the same (2.2.22), and I don't see anything relevant in any of the standard config files or /etc/sysconfig/httpd. And the rest of the system is reasonably similar, since they're built off the same CentOS 5 base image. I can't even tell from the Apache documentation whether REMOTE_ADDR is expected to exist or not as an environment variable, but it clearly works on one machine, whether by fluke or design, and the inconsistency is driving me mad.

  Read the article

• Why can't I get out of display mirror mode?

  - by Roy Smith

  I've been running Ubuntu (10.04.1 LTS, 64-bit) for a while and just replaced my hardware with a faster machine with an ATI Radeon HD 5700 video card. I've got twin 1920 x 1080 displays. I downloaded the latest driver (ati-driver-installer-10-9-x86.x86_64.run) from the ATI web site and installed that. I've gone through a few rounds of playing with /etc/X11/xorg.conf, and can't get things right. At the moment, it's in display mirroring mode, and I can't figure out how to get it out of mirror mode. If I run Monitor Preferences, there's a "Same image in all monitors" checkbox. If I uncheck that, the little preview window switches to show two monitors. When I click Apply, it asks me to log out and log back in again. When I do that, I'm right back to mirrored mode. What's really weird is that I'm currently running a copy of xorg.conf from a coworker's machine. He's got identical hardware, and his display works fine. So, I'm inclined to think there's something else going on other than the conf file. Any ideas what might be wrong?

  Read the article

• How to setup apache to catch a proxy_pass from nginx?

  - by Paté

  I have a working apache vhost such as <VirtualHost localhost:10006> DocumentRoot "/home/pate/***/git/kohana_site/public/site/" </VirtualHost> <VirtualHost *:10006> ServerName api.* DocumentRoot "/home/pate/***/git/kohana_site/public/api/" LogLevel debug </VirtualHost> If i point to localhost:10006 I get my website and api.localhost:10006 I get my api. Then I have haproxy setup on top of that, that runs on port 10010 and both localhost:10010 and api.localhost:10010 have the expected behaviour. Now I have nginx setup on port 80 with this configuration. server { listen 10000; server_name api.*; location / { proxy_pass http://legacy_server; } } server { listen 10000 default; server_name _; location /nginx_status { stub_status on; access_log off; } # images are accessed via the CDN over HTTP (not https) location /n/image { proxy_pass http://image_caching_server; } location / { return 301 https://$host:10014$request_uri; } } upstream legacy_server { server localhost:10010 fail_timeout=0; } the problem is that apache does not recognize the vhost properly and redirects api.localhost to the website instead of the api. I tried playing with set_proxy_header Host $host but it doesn't seem to do anything.

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

< Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >