Search Results

Search found 23062 results on 923 pages for 'multiple models'.

Page 753/923 | < Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >

  • Modem doesn't seem to pass internet connection to router

    - by Vian Esterhuizen
    I was supplied a Cisco DPC3825 modem by my ISP and use a Cisco E4200 as my main router. Today the Internet just stopped working, just out of the blue, I can't think of anything that would have triggered it. It's been working pretty good for the past month except for a few random blips here and there. After some trouble shooting I realized that a direct wired connection to the modem would get me Internet access but if I was wired to the router as I was before I would have no connection. Assuming it was router I connected a TP-Link WR841N but it had the exact same problem. Also, connecting to the router via Wi-Fi from multiple devices will connect me to the router but I still can't get access to the Internet. From these test, it seems that the modem just won't send Internet through to the router but is clearly connecting and able to directly connect to my PC. What I've Tried A full reset and factory reset on the E4200 A full reset on the modem (but I believe my ISP has remote access to the modem because the passwords and so on are always set back). My ISP has remotely reconfigured the modem What I Should Try What else can I try? What should I do to try to narrow down the issue? Can you figure out what the problem might be based on this information?

    Read the article

  • Virtual Machines Renaming/Backing up/Sharing

    - by evan
    I've started using VMware virtual machines for all of my software development projects and have a few questions for others doing the same thing. First, how can you rename the virtual machine and the name of the virtual hard drive? I have a base development machine that I clone for different projects. I'd like to name the machine and it's hard drive according the the project (right now when I copy them via cut and paste, the file names remain the same and I can only organize them by putting them in a specific directory). Second, what is the best way to back up a virtual machine? Is it possible (by breaking the virtual hard drive up into chunks instead of one big file) to get incremental backups working? It seems time machine always tries to make a copy of the whole thing which is time consuming because each virtual machine is around 30GB. Finally, how slow would it be to have a virtual machine shared on an NFS mount on a wireless N network and used from multiple computers (but with only one person using it at a time.) Would it be more reasonable on a gigabit lan connection? Thanks for your input! And please feel free to share any advice or wisdom about using virtual machines for software development and the best ways to speed them up!

    Read the article

  • Apache2 config problem

    - by Hellnar
    For using my Debian VPS for multiple domains , I did such actions: removed the default one from sites-enabled/ and sites-available/ (config and the symbolic link) and I added this under sites-available/www.mysite.com : <VirtualHost MYIP:80> ServerName mysite.com ServerAlias www.mysite.com Alias /media/ /home/myuser/mysite/media/ Alias /admin_media/ /home/myuser/django/Django-1.2/django/contrib/admin/media/ WSGIScriptAlias / /home/myuser/mysite/wsgi.py ErrorLog /home/myuser/mysite/logs/error.log CustomLog /home/myuser/mysite/logs/access.log combined </VirtualHost> And I have changed my ports.conf to: NameVirtualHost MYIP:80 Listen 80 <IfModule mod_ssl.c> # SSL name based virtual hosts are not yet supported, therefore no # NameVirtualHost statement here Listen 443 </IfModule> Lastly I enabled the new domain via the command: a2ensite www.mysite.com After restart I get this error: myuser:~# /etc/init.d/apache2 restart Restarting web server: apache2apache2: Syntax error on line 281 of /etc/apache2/apache2.conf: Syntax error on line 1 of /etc/apache2/sites-enabled/www.birertek.com: /etc/apache2/sites-enabled/www.birertek.com:1: <VirtualHost> was not closed. failed! Please help this poor soul.

    Read the article

  • How to stop SophosAV from scanning directories under source control

    - by user26453
    From googling it seems its well known that SophosAV as well as other AV programs have issues with how they interact and can inhibit source control utilities like TortoiseHG or TortoiseSVN. One solution is to exclude directories under source control from on-access scanning as detailed here on Sophos's support site. There is a corollary article that mentions some issues related to this, namely need to place multiple entries for exclusions based on the possibility of the location being accessed through the short vs. long name (e.g., Progra~1 vs. "Program Files"). One other twist is I am using a junction to relocate my user directory, C:\Users\Username, to a second hard drive, E:. Since I am not sure how this interacts I have included the source control directory as they are nested in both locations. As a result, I have included the two exclusions for the on-access scanning exclusions (and to be on the safe side on-demand exclusions as well, although this should only come into play when I select a parent directory of the exclusion to be scanned on-demand, but still). You'll notice I have no need to add extra exclusions for those locations based on short vs. long name distinctions. The two exclusion I have then, for both on-access and on-demand scanning exclusions are: C:\Users\Username\source-control-directory E:\source-control-directory However, this does not seem to work as TortoiseHG still lags terribly in response to any request as AV software starts scanning when the directory is accessed via TortoiseHG. I can verify without a doubt that Sophos is causing the problems: I can completely disable on-access scanning. Once this is done TortoiseHG responds very fast to all operations. I cannot leave this disabled obviously, but since the exclusion don't seem to be working, what next?

    Read the article

  • Setting up ProxyPass for a Virtualmin virtual server

    - by Andy Ibanez
    I am trying to set up my web server so that I can server multiple Ghost.org blogs. I am stuck in one crucial step. To be honest, my knowledge in servers is not so big, so I request your help to do this. Basically, a tutorial I'm reading suggests I set up a VirtualHost in this way: NameVirtualHost *:80 <VirtualHost *:80> ServerName your-url.com ServerAlias www.your-url.com ProxyRequests off ProxyPass / http://127.0.0.1:2368/ ProxyPassReverse / http:/127.0.0.1:2368/ </VirtualHost> So I have gone to the Virtual site on Virtualmin to try to add everything as is. Services Configure Website Edit Directives The problem is, the previous page (Services Configure website) says I can't edit the port: This Apache virtual host belongs to the Virtualmin server linguist.andyibanez.com, so the address, port, base directory and hostname cannot be changed here. And whenever I try to add the ProxyRequests off (the other two can be added fine) directive in Edit Directives manually, I'm simply told that the directive can't be there. So what is the right way to "add" the last three directives in the VirtualHost above to my sub server? Maybe I'm missing a menu item that will help me with this? I request your help as I have looked for a while, Google keeps thinking I want to serve Webmin via Apache when I google "Set up Virtualmin proxypass", and I have no clue what to do.

    Read the article

  • Getting at fsid under Linux? Or an alternate way of identifying filesystems?

    - by larsks
    In an environment with automounted home directories, such that the same filesystem exported by a fileserver may be mounted multiple times on the client, I would like to authoritatively be able to identify whether two mountpoints are in fact the same filesystem. That is, if the remote server exports: /home And the local client has: # mount fileserver:/home/l/lars on /home/lars type nfs (rw...) fileserver:/home/b/bob on /home/bob type nfs (rw...) I am looking for a way to identify that both /home/lars and /home/bob are in fact the same filesystem. In theory this is what the fsid result of the statvfs structure is for, but in all cases, for both local and remote filesystems, I am finding that the value of this structure member is 0. Is this some sort of client-side issue? Or do most modern NFS servers simply decline to provide a useful fsid? The end goal of all of this is to robustly interpret the output from the quota command for NFS filesystems. For example, given the example above, running quota as myself may return something like: Disk quotas for user lars (uid 6580): Filesystem blocks quota limit grace files quota limit grace otherserver:/vol/home0/a/alice 12 52428800 52428800 4 4294967295 4294967295 fileserver:/home/l/lars 9353032 9728000 10240000 124018 0 0 ...the problem here being that there exists a quota for me on otherserver which is visible in the results of the quota command, even though my home directory is actually on a different device. My plan was to look up the fsid for each mountpoint listed in the quota output and check to see if it matched the fsid associated with my home directory. It looks like this won't work, so...any suggestions?

    Read the article

  • Exchange 2007 two node cluster setup on Windows 2008 Enterprise, install error

    - by Shadow00Caster
    I am installing Microsoft Exchange 2007 x64 in a two node environment using Microsoft Windows 2008 Enterprise x64. The Failover Cluster is all setup properly and following best practices for setting up the windows clustering for use with Exchange 2007. All the validation tests pass on the cluster and all of that portion is working fine. The problem is when I go to install the first Exchange node as an Active mailbox in configuration for a two node CCR. It gets all the way through the first 3 steps (Copy Exchange Files, Management Tools, Mailbox Role) and then fails on the 4th step 'Clustered Mailbox Server' with the following error: Error: The clustered mailbox server's group 'XXXX' was not found, and should already exist. Firewalls are all disabled, DNS is all setup properly, the environment has 3 domain controllers all 2k8 ent x64, all replication works. The name I pick for the CCR cluster (XXX) does not exist in AD or in DNS. I have attempted this install from both of the two Exchange nodes and multiple times .. tried with different names. I have been banging my head against the wall for days working on this and would appreciate any feedback on the issue.

    Read the article

  • unreadable corrupted ntfs partition - lost clusters reported

    - by Eduardo Martinez
    partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

    Read the article

  • Does any Certificate Authority support both SAN and wildcards?

    - by nicholas a. evans
    My basic quandry is that wildcard certificates don't support subdomains of subdomains, nor do they help with alternate domain names. Basically, if my CN is example.com, I want a Subject Alternative Name field that looks roughly like so: DNS:example.com DNS*.example.com DNS:*.beta.example.com DNS:example.net DNS:*.example.net DNS:*.beta.example.net Using a self-signed cert, I verified that the browsers will work just fine with this. Unfortunately, none of the Certificate Authorities that I looked into (Thawte, GoDaddy, Verisign, Digicert) seemed to support both wildcard certs and Subject Alternative Name (sometimes referred to as "Multiple Domain UCC"). I even called up GoDaddy tech support to confirm. Is there a CA (trusted by 99% of browsers) that supports wildcards for the Subject Alternative Name? One little restriction: I'm saddled with Amazon EC2's single Elastic IP per instance limitation. Here are what I see as my backup plans: set up three extra EC2 instances, each configured for a different IP address and cert, and nginx reverse proxy from three of them into the app server(s) introduces latency(?), and even the cheapest EC2 instance isn't that cheap instead of dedicated reverse proxy instances, setup the four or more almost identical EC2 app servers, with nginx using the port to determine which cert to deliver, and use haproxy to distribute the traffic amongst themselves. complicated to configure and manage? I'm not using the cheapest EC2 instance type for my app servers. If I don't need 4+ app servers for the load, it raises the cost. set up an external server (outside of EC2) that doesn't have EC2's Elastic IP address restrictions, setup all of the alternate IP addresses and certificates on that server, and nginx reverse proxy from that server into the EC2 app servers. extra IP addresses are almost free (still need to pay for the server of course), but don't come with the robust "elasticity" that Amazon's Elastic IPs provide. even more latency than in the first scenario. Are these approaches crazy or reasonable? Do you have another one to suggest?

    Read the article

  • 426 Connection closed; transfer aborted.

    - by Jiaoziren
    Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

    Read the article

  • Apache Caching and Expires configuration

    - by mcondiff
    I'm looking for a best possible caching/expires configuration for my specific situation. I realize that some sites have advocated turning etags off: Header unset ETag, FileETag None I know that I should use either Expires or Cache-Control. In additions, I know that I should use either Last-modified or ETAGs (Per ySlow docs). I inherited a clients server that uses the following in .htaccess: <FilesMatch "\.(ico|pdf|flv|jpg|jpeg|png|gif|js|css|swf|xml|txt|html|htm)$"> Header set Cache-Control "max-age=172800, public, must-revalidate" </FilesMatch> With this server I am not going to be able to rely on staff to rename images, css and js in web applications so I do not want to set the expires far in the future without knowing (with a good certainty) that "most/all" browsers will check to see if content has changed. What I do not want to happen is someone call me and say the website is broken because they replaced an image and it's not showing up. But I do want to take the most advantage I can with caching and expires while still maintaining that mostly all browsers will check with the server to see if components have changed. I have access to both the .htaccess and apache .conf file and it is a single server, the content is not deployed on multiple servers. What would be the best .htaccess or .conf configuration for me to achieve my goals for this clients server? Thanks for your help

    Read the article

  • How to automatically remove Flash history/privacy trail? Or stop Flash from storing it?

    - by Arjan van Bentem
    Many people have heard about third-party cookies, and some browsers even block those by default. Some people may even be using Private Browsing modes. However, only few seem to realise that Adobe's Flash player also leaves a cross-browser trail on your local hard drive, and allows for sending cookie-like information back to the server, including third-party sites. And because it is a plugin, Flash does not take any of the browser's privacy settings into account. Sorry for the long post, but first some details about why using Flash raises a privacy concern, followed by the results of my tests: The Flash player keeps a cross-browser history of the domain names of the Flash-sites your computer has visited. Unlike your browser's history, this history is not limited to a certain number of days. History is also recorded while using so-called Private Browsing modes. It is stored on your hard drive (though, as described below, without going to Adobe's site you won't know what is stored). I am not sure if any date and time information is kept about each visit, but to see the domain names: right-click on some Flash content, open the settings dialog, and click the Help icon or click the Advanced button within the Privacy tab. This opens a browser to the help pages on Adobe.com, where one can click through to the Website Storage Settings panel. One can clear the existing list, but one cannot stop it from being recorded again. Flash allows for storing data on your local hard drive, using so-called Local Shared Objects (aka "Flash Cookies"). Just like HTTP cookies, this data can be sent back to the server, for tracking purposes. They are cross-browser, have no expiration date, and no user defined maximum lifetime can be set in the Flash preferences either. These not being HTTP cookies, they are (of course) not blocked by a browser's cookies preferences and are not removed when the normal HTTP cookies are deleted. Adobe has announced that version 10.1 will obey Private Browsing in most popular browsers, but unfortunately no word about also removing the data whenever normal cookies are deleted manually. And its implementation might be confusing: [..] if the browser is in normal browsing mode when the Flash Player instance is created, then that particular instance will forever be in normal browsing mode (private browsing is turned off). Accordingly, toggling private browsing on or off without refreshing the page or closing the private browsing window will not impact Flash Player. Local Shared Objects are not limited to the site you visit, and third-party storage is enabled by default. At the Global Storage Settings panel one can deselect the default Allow third-party Flash content to store data on your computer. Because of the cross-browser and expiration-less nature (and the fact that few people know about it), I feel that the cross-browser third-party Flash Cookies are more dangerous for visitor tracking than third-party normal HTTP cookies. They are even used to restore plain HTTP cookies that the user tried to delete: "All advertisers, websites and networks use cookies for targeted advertising, but cookies are under attack. According to current research they are being erased by 40% of users creating serious problems," says Mookie Tenembaum, founder of United Virtualities. "From simple frequency capping to the more sophisticated behavioral targeting, cookies are an essential part of any online ad campaign. PIE ["Persistent Identification Element"] will give publishers and third-party providers a persistent backup to cookies effectively rendering them unassailable", adds Tenembaum. [..] To justify this tracking mechanism, UV's Tenembaum said, "The user is not proficient enough in technology to know if the cookie is good or bad, or how it works." When selecting None (zero KB) for Specify the amount of disk space that website websites that you haven't yet visited can use to store information on your computer, and checking Never ask again then some sites do not work. However, the same site might work when setting it to None but without selecting Never ask again, and then choose Deny whenever prompted. Both options would result in zero KB of data being allowed, but the behaviour differs. The plugin also provides a Flash Player cache for Adobe-signed files. I guess these files are not an issue. So: how to automatically delete that information? On a Mac, one can find a settings.sol file and a folder for each visited Flash-website in: $HOME/Library/Preferences/Macromedia/Flash Player/macromedia.com/support/flashplayer/sys/ Deleting the settings.sol file and all the folders in sys, removes the trail from the settings panels. However, the actual Local Shared Ojects are elsewhere (see Wikipedia for locations on other operating systems), in a randomly named subfolder of: $HOME/Library/Preferences/Macromedia/Flash Player/#SharedObjects But then: how to remove this automatically? Simply removing the folders and the settings.sol file every now and then (like by using launchd or Windows' Task Scheduler) may interfere with active browsers. Or is it safe to assume that, given the cross-browser nature, the plugin would not care if things are removed while it is active? Only clearing during log-off may not work for those who hibernate all the time. Firefox users can install BetterPrivacy or Objection to delete the Local Shared Objects (for all others browsers as well). I don't know if that also deletes the trail of website domain names. Or: how to stop Flash from storing a history trail? Change of plans: I'm currently testing prohibiting Flash to write to its own sys and #SharedObjects folders. So far, Flash has not tried to restore permissions (though, when deleting the folders, Flash will of course recreate them). I've not encountered any problems but this may take some while to validate, using multiple browsers and sites. I've not yet found a log that reports errors. On a Mac: cd "$HOME/Library/Preferences/Macromedia/Flash Player/macromedia.com/support/flashplayer" rm -r sys/* chmod u-w sys cd "$HOME/Library/Preferences/Macromedia/Flash Player" # preserve the randomly named subfolders (only preserving the latest would suffice; see below) rm -r \#SharedObjects/*/* chmod -R u-w \#SharedObjects I guess the above chmods cannot be achieved on an old Windows system (I'm not sure about XP and Vista?). Though maybe on Windows one could replace the folders sys and #SharedObjects with dummy files with the same names? Anyone? Obviously, keeping Flash from storing those Local Shared Objects for all sites may cause problems. Some test results (Flash 10 on Mac OS X): When blocking the sys folder (even when leaving the #SharedObjects folder writable) then YouTube won't remember your volume settings while viewing multiple videos. Temporarily allowing write access to the blocked folders while visiting trusted sites (to only create folders for domains you like, maybe including references in settings.sol) solves that. This way, for YouTube, Flash could be allowed to write to sys/#s.ytimg.com and #SharedObjects/s.ytimg.com, while Flash could not create new folders for other domains. One may also need to make settings.sol read-only afterwards, or delete it again. When blocking both the sys and #SharedObjects folders, YouTube and Vimeo work fine (though they might not remember any settings). However, Bits on the Run refuses to even show the video player. This is solved by temporarily unblocking the #SharedObjects folder, to allow Flash to create a subfolder with some random name. Within this folder, it would create yet another folder for the current Flash website (content.bitsontherun.com). Removing that website-specific folder, and blocking both #SharedObjects and the randomly named subfolder, still seems to allow Bits on the Run to operate, even though it still cannot write anything to disk. So: the existence of the randomly named subfolder (even when write protected) is important for some sites. When I first found the #SharedObjects folder, it held many subfolders with random names, some created on the very same day. I wonder when Flash decides it wants a new folder, and how it determines (and remembers) that random name. For a moment I considered not blocking write access for sys and #SharedObjects, but explicitly creating read-only folders for well-known third-party tracking domains (like based on a list from, for example, AdBlock Plus). That way, any other domain could still create Local Shared Objects. But the list would be long, and the domains from AdBlock Plus are probably all third-party domains anyway, so disabling Allow third-party Flash content to store data on your computer might have the very same result. Any experience anyone? (Final notes: if the above links to the settings panels do not work in the future, then use the URL that is known to Flash player as a starting point: www.adobe.com/go/settingsmanager. See also "You Deleted Your Cookies? Think Again" at Wired.com -- which uses Flash cookies itself as well... For the very suspicious using Time Machine: you may want to exclude both folders, for each user, and remove the trace that is already on your backup.)

    Read the article

  • Developer's PC - worth getting more than 8GB RAM?

    - by Borek
    I'm building a developer PC and am wondering whether to get 8GB or 12GB. It's a Core-i7 860 system, i.e., 1156 motherboards with 4 slots for RAM sticks, dual channel, usually up 16GB (as opposed to 1366 sockets where 6 banks / triple-channel are used). 8GB would be cheaper to get especially because price per GB is lower with 4x2GB compared to 2x4GB. Also the availability is worse for 4GB DIMMs here where I live; those are the main practical advantages of 8GB. (Edit: I should have stressed the price difference more - in the eshop I'm buying from, the difference between 12GB and 8GB is so big that I could almost buy a whole new netbook for it.) However, I understand that more RAM can never do harm which is the point of this question - how much of a difference will 12GB make as opposed to 8GB? Honestly, I've always been on 3.2GB systems (4GB but 32bit system) and never felt much pain from having too little memory - of course there could be more but for instance compiler's performance was usually held back by slow I/O or not utilizing multiple cores on my CPU. Still, I'm not questioning that 8GB will be useful, however, I'm not sure about the additional 4GB difference between 8 and 12 gig. Anyone has experience with 8GB / 12GB systems? The software I usually run all the time: Visual Studio or Eclipse (both should be fine with ~2GB RAM, after that I feel their performance is I/O bound) Firefox (it can never have enough RAM can it? :) Office (~500MB RAM should be enough) ... and then some smaller apps like Skype, other browsers, some background services etc.

    Read the article

  • prevent IE8 tabs from opening tabs in stack in taskbar

    - by Nano8Blazex
    This may have been asked before too... But, anyways. I'm using Windows 7 Ultimate, and IE 8, and have the taskbar in icon view. I'm not sure how to explain this, but I'm amazed at how each tab in IE8 seems to act like a new "process" in the taskbar (as if each tab was a window). Like... each tab acts like a different window in the taskbar although they are actually running in the same window. Now when I use IE 8 it looks (in the taskbar) like there's 15 windows open when in fact the taskbar is simply showing the 15 tabs. More simply put, it's displaying a "stack" for all of the tabs when I'd rather have the icon act like, for example, firefox so that a stack is only shown for the multiple windows. I know that they are meant to be running as separate processes to prevent crashing and the such... but is there a way to disable this strange "taskbar" effect? I'd rather have the taskbar show the main window and not the tabs individually. There has to be a simple way to do this...

    Read the article

  • Amazon AWS EC2 + Puppet, get Puppet to know AWS instance tags

    - by Piotr Jasiulewicz
    I am having a problem with my AWS deployment, fairly new to AWS and Puppet. So coming to my question - can you distinguish puppet nodes with AWS machine tags or CNAME domains? A little background about the plan: have multiple clusters of machines, one php cluster, one legacy php cluster, one java cluster, one perl cluster control configuration with puppet - still pretty new to puppet but as a developer I like the idea of being able to version control configuration of servers have autoscaling enabled on those clusters - obviously the main benefit of the cloud that makes the much hight cost when it comes to any reasonable performance worth it (those amazon machines are slower than my phone...) deployment controlled by Capistrano, this makes things a lot easier So in AWS you get those super nasty public/private machine dns's... no way you can identify machines on those. In order to easer the problem, seams like AWS want's you to tag everything - so I did. Found a script that makes a CNAME record for each machine with the tag "ShortName" thanks to the Route53 API. Every machine has a ShortName tag that becomes its CNAME, unfortunately puppet still resolves the private dns name. I'd like to have node 'perl-cluster'{} in puppet, anyone any clue ho to achieve this? Thanks

    Read the article

  • NRPE unable to read output, but why?

    - by ticktockhouse
    I have this problem with NRPE, all the stuff I've found so far on the net seems to point me at things I've already tried. # /usr/local/nagios/plugins/check_nrpe -H nrpeclient gives NRPE v2.12 as expected. Running the command by hand (as defined in nrpe.cfg on "nrpeclient", gives the expected response nrpe.cfg: command[check_openmanage]=/usr/lib/nagios/plugins/additional/check_openmanage -s -e -b ctrl_driver=0 bat_charge "Expected response" But if I try to run the command from the Nagios server I get the following: # /usr/local/nagios/plugins/check_nrpe -H comxps -c check_openmanage NRPE: Unable to read output Can anyone think of anywhere else I might have made a mistake with this? I've done the same thing on multiple other servers with no problem. The only difference I can think of with this is that this box is RHEL 5 based, whereas the others are RHEL 4 based. Those two bits above that I've tested are the what most people seem to suggest when people have had this problem. I should mention that I get a weird error in the logs when I restart nrpe: nrpe[14534]: Unable to open config file '/usr/local/nagios/etc/nrpe.cfg' for reading nrpe[14534]: Continuing with errors... nrpe[14535]: Starting up daemon nrpe[14535]: Warning: Daemon is configured to accept command arguments from clients! nrpe[14535]: Listening for connections on port 5666 nrpe[14535]: Allowing connections from: bodbck,combck,nam-bck Even though, it's plainly reading that /usr/local/nagios/etc/nrpe.cfg file to get the stuff it's talking about further down..

    Read the article

  • Bash script 'while read' loop causes 'broken pipe' error when run with GNU Parallel

    - by Joe White
    According to the GNU Parallel mailing list this is not a GNU Parallel-specific problem. They suggested that I post my problem here. The error I'm getting is a "broken pipe" error, but I feel I should first explain the context of my problem and what causes this error. It happens when trying to use any bash script containing a 'while read' loop in GNU Parallel. I have a basic bash script like this: #!/bin/bash # linkcheck.sh while read domain do host "$domain" done Assume that I want to pipe in a large list (250mb say). cat urllist | ./linkcheck.sh Running host command on 250mb worth of URLs is rather slow. To speed things up I want to break up the input into chunks before piping it and then run multiple jobs in parallel. GNU Parallel is capable of doing this. cat urllist | parallel --pipe -j0 parallel ./linkcheck.sh {} {} is substituted by the contents of urllist line-by-line. Assume that my systems default setup is capable of running 500ish jobs per instance of parallel. To get round this limitation we can parallelize Parallel itself: cat urllist | parallel -j10 --pipe parallel -j0 ./linkcheck.sh {} This will run 5000'ish jobs. It will also, sadly, cause the error "broken pipe" (bash FAQ). Yet the script starts to work if I remove the while read loop and take input directly from whatever is fed into {} e.g., #!/bin/bash # linkchecker.sh domain="$1" host "$1" Why will it not work with a while read loop? Is it safe to just turn off the SIGPIPE signal to stop the "broken pipe" message, or will that have side effects such as data corruption? Thanks for reading.

    Read the article

  • When using procmail with maildir, it returns error with code I found

    - by bradlis7
    I'm not an expert at procmail, but I have this code: DROPPRIVS=yes DEFAULT=$HOME/Maildir/ :0 * ? /usr/bin/test -d $DEFAULT || /bin/mkdir $DEFAULT { } :0 E { # Bail out if directory could not be created EXITCODE=127 HOST=bail.out } MAILDIR=$HOME/Maildir/ But, when the directory already exists, sometimes it will send a return email with this error: 554 5.3.0 unknown mailer error 127. The email still gets delivered, mind you, but it sends back an error code. I fixed this temporarily by commenting out the EXITCODE and HOST lines, but I'd like to know if there is a better solution. I found this block of code in multiple places across the net, but couldn't really find why this error was coming back to me. It seems to happen when I send an email to a local user, sometimes the user has a .forward file to send it on to other users, sometimes not, but the result has been the same. I also tried removing DROPPRIVS, just in case it was messing up the forwarding, but it did not seem to affect it. Is the line starting with * ? /usr/bin/test a problem? The * signifies a regex, but the ? makes it return an integer value, correct? What is the integer being matched against? Or is it just comparing the integer return value? Thanks for the help.

    Read the article

  • Running Mathematica-5 remotely

    - by oxinabox.ucc.asn.au
    I have Mathematica 5 - a powerful CAS. I have a cheap netbook (running Windows XP), wich not only is too slow to run mathmatica on, I doubt it has the harddrive space. I do however have remote access to a number of very powerful computers, (most of wich run variose Linuxes, but one of which is Windows Server 2008, though I'ld rather not use this one*). Mostly over SSH but other protocols can be arraged for some, I'm sure. So I'ld like to install Mathematica onto one of these machine and then run it remotely. Either from the command line via Putty or via some other method. I glanced through the mathematical documentation and read something about using some MathLink program, which links the front end installed on my computer to a remote kernel. Anyone have any experience with this? I'm not sure if this belongs here or in SuperUser. At the moment, it's being tinkered with, and when the tinkering stops it'll likely be used to run multiple thin terms. As compared to the Linux machines: I have access to a dual 2.4 Xeon with 3GB RAM, which the rest of the world seems to have completely forgotten about (runs freeBSD!).

    Read the article

  • Issues resolving DNS entries for multi-homed servers

    - by I.T. Support
    This is difficult to explain, so bear with me. We have 2 domain controllers, each multi-homed to straddle 2 internal subnets, (subnet A and subnet B) and provide dns, dhcp, and ldap authentication. Both domain controllers each have 2 DNS entries. both entries have identical host names, but correspond to subnet A & subnet B respectively (example entries shown): dc1 host 192.168.8.1 dc1 host 192.168.9.1 dc2 host 192.168.8.2 dc2 host 192.168.9.2 We also have a 3rd subnet for our dmz, (subnet C) which neither domain controller has an IP address on, but our firewall/routing tables provide access to subnet A from subnet C and vice versa, but don't allow access to subnet B from subnet C. Here's my issue. How can I force/determine which dns entry is used when a server on subnet C queries either domain controller by host name? Right now it seems to randomly pick one of the two entries, swaps out the name for the IP address and that's that. The problem is if it randomly selects the entry that corresponds to the 9.x subnet B (no access from subnet C), then the server fails to resolve. If it picks the entry for the 8.x subnet A then it resolves (firewall/routing tables defined for communication between these 2 subnets) Here's what I'd like to know: What are Best Practices (if any) for dealing with DNS resolution on subnets that the DNS servers don't have a presence on? Can I control something akin to a metric value to force an order of DNS resolution when there are multiple entries for the same host name that correspond to different IP subnets? Should I even have 2 DNS HOST entries for the same name? Here's what I'd like to avoid: Making edits to the HOSTS files of servers on subnet C to force DNS resolution of the hostname to the appropriate subnet Adding NIC's to the DC's to have them straddle the DMZ as well, thus obtaining a third DNS entry that corresponds to subnet C Again, my apologies if this was too verbose / unclear. Thanks!

    Read the article

  • Changing externally visible IP on a multi-IP router?

    - by AlternateZ
    I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

    Read the article

  • Windows Terminal Server: occasional memory violation for applications

    - by syneticon-dj
    On a virtualized (ESXi 4.1) Windows Server 2008 SP2 32-bit machine which is used as a terminal server, I occasionally (approximately 1-3 event log entries a day) see applications fail with an 0xc0000005 error - apparently a memory access violation. The problem seems quite random and only badly reproducable - applications may run for hours, fail with 0xc0000005 and restart quite fine or just throw the access violation at startup and start flawlessly at the second attempt. The names of executables, modules and offset addresses vary, although a single executable tends to fail with same modules and the same memory offset addresses (like "OUTLOOK.EXE" repeatedly failing on module "olmapi32.dll" with the offset "0x00044b7a") - even across multiple user's logons and with several days passing without a single failure inbetween. The offset addresses seem to change across reboots, however. Only selective executables seem affected by the problem, although I may simply not be seeing a sufficient number of application runs from the other ones. I first suspected a possible problem with the physical machine's RAM, but ruled this out as a rather unlikely cause - the memory comes with ECC and I've already moved the virtual machine across several times, without any perceptable change. I've seen that DEP was enabled in "OptOut" mode on this machine: C:\Users\administrator>wmic OS Get DataExecutionPrevention_SupportPolicy DataExecutionPrevention_SupportPolicy 3 and tried changing the policy to OptIn via startup options: bcdedit.exe /set {current} nx OptIn but have yet to see any effect - I also would expect Outlook 12 or Adobe Reader 9 (both affected applications) to play well with DEP. Any other ideas why the apps may be failing?

    Read the article

  • Python easy_install confused on Mac OS X

    - by slf
    environment info: $ echo $PATH /opt/local/bin:/opt/local/sbin:/sw/bin:/sw/sbin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin:/usr/X11R6/bin:/opt/local/bin:/Developer/Platforms/iPhoneOS.platform/Developer/usr/bin:~/.utility_scripts $ which easy_install /usr/bin/easy_install specifically, let's try the simplejson module (I know it's the same thing as import json in 2.6, but that isn't the point) $ sudo easy_install simplejson Searching for simplejson Reading http://pypi.python.org/simple/simplejson/ Reading http://undefined.org/python/#simplejson Best match: simplejson 2.1.0 Downloading http://pypi.python.org/packages/source/s/simplejson/simplejson-2.1.0.tar.gz#md5=3ea565fd1216462162c6929b264cf365 Processing simplejson-2.1.0.tar.gz Running simplejson-2.1.0/setup.py -q bdist_egg --dist-dir /tmp/easy_install-Ojv_yS/simplejson-2.1.0/egg-dist-tmp-AypFWa The required version of setuptools (>=0.6c11) is not available, and can't be installed while this script is running. Please install a more recent version first, using 'easy_install -U setuptools'. (Currently using setuptools 0.6c9 (/System/Library/Frameworks/Python.framework/Versions/2.6/Extras/lib/python)) error: Setup script exited with 2 ok, so I'll update setuptools... $ sudo easy_install -U setuptools Searching for setuptools Reading http://pypi.python.org/simple/setuptools/ Best match: setuptools 0.6c11 Processing setuptools-0.6c11-py2.6.egg setuptools 0.6c11 is already the active version in easy-install.pth Installing easy_install script to /usr/local/bin Installing easy_install-2.6 script to /usr/local/bin Using /Library/Python/2.6/site-packages/setuptools-0.6c11-py2.6.egg Processing dependencies for setuptools Finished processing dependencies for setuptools I'm not going to speculate, but this could have been caused by any number of environment changes like the Leopard - Snow Leopard upgrade, MacPorts or Fink updates, or multiple Google App Engine updates.

    Read the article

  • Online Storage and security concerns

    - by Megge
    I plan to set up a small fileserver. I already own a small server at HostEurope (VirtualServer L, 250GB space), but they don't offer enough space (there is the HostEurope Cloud, but paying for bandwidth isn't an option here, video-streaming should be possible) Requirements summarized: Storage: 2TB, Users: ~15, Filesizes: < 100GB, should be easily reachable (Mount as a networkdrive or at least have solid "communication" software) My first question would be: Where can I get halfway affordable online storages? And how should I connect them to my server? Getting an additional server is a bit overkill, as I know no hoster which allows 2 TB on a small 2 Ghz Dual Core 2 GB RAM thingy (that would be enough by far, I just need much space), and connecting it via NFS or FTP over Internet seems a bit strange and cripples performance. Do you have any advice where I could get that storage service from? (I sent HostEurope a custom request today, but they didn't answer till now. If they can provide me with that space, this question will be irrelevant, but the 2nd one is the more important one anway, don't do much more than recommend me some based on experience, you don't have to crawl hours through hosting services) livedrive for example offers 5 TB for 17€ / month, I'd be happy with 2 TB for 20 €, the caveat is: It doesn't allow multiple users, which leads me to my second question: Where are the security problems? Which protocol is sufficient (I want private and "public" folders etc. the usual "every user has its own and a public space"-thing), secure and fast? (I'd tend to (S)FTP, problem with FTP is: Most of those hosting services don't even allow FTP with mutliple users and single users lead me into "hacking" a solution (you could map the basic folder structure on the main server and just mount every subfolder from the storage, things get difficult with a public folder with 644 permissions though) Is useing something like PKI or 802.1X overkill for private uses?

    Read the article

  • Can't get an IBM xSeries 345 server to load Windows Server 2003 using ServerGuide utility

    - by Kyle Noland
    I have a client that has an IBM xSeries 345 eServer. Per the IBM support website, I have downloaded the ServerGuide Setup 7.4.17 installation ISO and burned a bootable CD. The CD boots fine and loads the utility. I walk through the following screens without any issue: Set the date and Time Detect the IBM ServeRAID card and install the latest firmware Clear the hard disks Set up the RAID array The next step is format the NOS partition. I select my partition size and the utility goes through the following steps: Creating NOS partition Formatting NOS partition (NTFS) Copying W32 files The copying W32 files takes about 10 minutes. I see the CD drive and disks working hard. When the copying is complete, I'm taken to a blank page just NOS Partitioning at the top. At the bottom of the screen are the familiar Back and Exit buttons. I see the place where the Next button should be, and if I click on it I can tell there is something there, but the space is empty. No button is displayed and clicking the empty spot doesn't ever take me to the next screen. I can't load the OS until I get past this part. I have already tried: Burning multiple copies and versions of the ServerGuide CD Letting the final screen just sit there over the weekend thinking it might advance after syncing the drives or something Has anybody else seen this? I'm really at a loss here. EDIT: I found another person who has the exact same problem as me: http://www.ibm.com/developerworks/forums/thread.jspa?messageID=14451763

    Read the article

< Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >