Search Results

Search found 20671 results on 827 pages for 'android device'.

Page 761/827 | < Previous Page | 757 758 759 760 761 762 763 764 765 766 767 768  | Next Page >

  • How to create btrfs RAID-1 filesystem (assertion error in mkfs.btrfs)?

    - by amcnabb
    I tried to make a btrfs RAID-1 filesystem in "degraded mode" by following the btrfs UseCases instructions but hit a fatal assertion error. Why is this failing, and is there any workaround? The instructions I followed are at: https://btrfs.wiki.kernel.org/articles/u/s/e/UseCases_8bd8.html The output of the mkfs.btrfs and btrfs filesystem show commands is: # mkfs.btrfs -m raid1 -d raid1 /dev/sdd1 /dev/loop1 WARNING! - Btrfs Btrfs v0.19 IS EXPERIMENTAL WARNING! - see http://btrfs.wiki.kernel.org before using failed to read /dev/sr0 adding device /dev/loop1 id 2 mkfs.btrfs: volumes.c:802: btrfs_alloc_chunk: Assertion `!(ret)' failed. zsh: abort (core dumped) mkfs.btrfs -m raid1 -d raid1 /dev/sdd1 /dev/loop1 # btrfs filesystem show failed to read /dev/sr0 Label: none uuid: 773908b8-acca-4c30-85c5-6642b06de22b Total devices 1 FS bytes used 28.00KB devid 1 size 223.13GB used 2.04GB path /dev/sda5 Label: none uuid: 0f06f1a8-5f5f-4b92-a55c-b827bcbcc840 Total devices 2 FS bytes used 24.00KB devid 2 size 2.00GB used 0.00 path /dev/loop1 devid 1 size 1.36TB used 20.00MB path /dev/sdd1 Btrfs Btrfs v0.19 # EDIT: It turns out that the filesystem isn't mountable: # mount /dev/sdd1 /mnt/big2 mount: wrong fs type, bad option, bad superblock on /dev/sdd1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # So, why did the mkfs fail, and is there any workaround?

    Read the article

  • Defeating the RAID5 write hole with ZFS (but not RAID-Z) [closed]

    - by Michael Shick
    I'm setting up a long-term storage system for keeping personal backups and archives. I plan to have RAID5 starting with a relatively small array and adding devices over time to expand storage. I may also want to convert to RAID6 down the road when the array gets large. Linux md is a perfect fit for this use case since it allows both of the changes I want on a live array and performance isn't at all important. Low cost is also great. Now, I also want to defend against file corruption, so it looked like a RAID-Z1 would be a good fit, but evidently I would only be able to add additional RAID5 (RAID-Z1) sets at a time rather than individual drives. I want to be able to add drives one at a time, and I don't want to have to give up another device for parity with every expansion. So at this point, it looks like I'll be using a plain ZFS filesystem on top of an md RAID5 array. That brings me to my primary question: Will ZFS be able to correct or at least detect corruption resulting from the RAID5 write hole? Additionally, any other caveats or advice for such a set up is welcome. I'll probably be using Debian, but I'll definitely be using Linux since I'm familiar with it, so that means only as new a version of ZFS as is available for Linux (via ZFS-FUSE or so).

    Read the article

  • How to set up a serial connection to a Windows 7 computer

    - by oli_arborum
    I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

    Read the article

  • Sharing files between 2 different routers

    - by Chris
    I realize this has been asked before and I have read as much as I could find on the topic but I still need help with this because there are so many different approaches and the ones I am trying aren't working. So I have 2 routers, lets call them A and B. Both have a wireless feature and are active. A is in the basement and receives the internet. There is a TV on the ground floor that is connected to A through an ethernet wire. B is upstairs and gets the internet from A through an ethernet wire. Connected to B, is a desktop running Plex Media Server. What I want to do is make sure devices connected to both routes can access the Plex Media Server. So what I have read is that I should plug in the ethernet wire connecting B to a into a LAN port instead of the WAN port. After that I should turn off DHCP. I have tried this and B stops receiving internet. What am I doing wrong? Another thing I have read is to use Router B in bridge mode but Router B is running openwrt and I have QoS on it so gaming/VoIP/browsing is unaffected by heavy downloading/uploading. I would prefer to keep this active. I realize it might be ineffective if a device in Router A is doing some hardcore downloading but all that stuff is done on Router B anyway so it doesn't matter. Router A can't get openwrt because it is a shitty one provided by Bell. So, how do I proceed with this?

    Read the article

  • Microsoft Arc Mouse OS X

    - by meepz
    I recently bought a new Mac Book Pro with Mountain Lion 10.8 on it. The only portable mouse I have is my Microsoft Arc Mouse. I wanted to use it with the laptop so I installed the IntelliPoint 8.2 for Mac from Microsofts website. According to their website, this driver is for OS X 10.4-10.7. Now I thought that wouldnt be too much of an issue but unfortunately for me, the driver installs fine and the mouse is detected but I get no movement and when I click the buttons nothing happens. I took the mouse with me on a business trip to EU and before I left I checked if the mouse worked with my desktop which is running Windows 7 and it worked without any hiccups. I'm not too sure where the OS differs from 10.7 to 10.8. I found an article online but it doesn't pertain to my mouse, although it could be of assistance. I have tried my version of their adjustment but I am not too knowledgable on low level hardware/software modifications so I may have done it wrong. heres the link: http://refluxions.wordpress.com/2008/08/18/mac-os-x-mouse-madnessfixed/ I get the following details when I check mouse info in the IntelliPoint preferences pane: The following Microsoft mouse devices are currently connected to your Macintosh driven by the Intellipoint software. Arc Mouse Vendor name: Microsoft Product name: Microsoft AE 2.4GHz Transceiver 5.0 Vendor ID: 045E Product ID: 074F Device version: 0140 if anyone has any suggestions on how to fix this it would be greatly appreciated! I love the mouse and im here in EU for another two weeks. Thanks

    Read the article

  • ATI HDMI Audio disappears in Windows 7 when a TV is connected

    - by jsalonen
    So far I have unsuccessfully googled for HOURS with no luck fixing this very annoying problem. The settings is the following: I have PC running Windows 7 RC (64-bit) Video card is a ATI Radeon 4850 series card (Sapphire HD 4850 512MB to be exact) The video card has HDMI out with built-in audio chip I have an HDMI cable connecting the PC to a TV (Sony Bravia series) The problem is that when I connect the HDMI cable to the TV, the ATI HDMI Sound output device disappears completely from the list of playback devices in Windows. As a workaround I can restore the audio by re-installing the HDMI audio driver. However, when I disconnect the TV the driver disappears again. So basically, every time I want to watch stuff on my TV, I have to reinstall audio driver, which of course is VERY annoying. EDIT: I have figured out that I do not need to re-istall the HDMI audio driver to restore sound; I only need to reboot my computer with the HDMI cable plugged in to restore the audio driver. This suggests that the problem has something to do with information passed from TV to computer, which makes my HDMI Audio driver disappear. Are there any other, more elegant workarounds for this problem? All help is much appreciated!

    Read the article

  • How to get a higher resolution on Ubuntu 11.04 using an intel chipset

    - by Saif Bechan
    I have a bit slow PC here, so I decided to put Ubuntu 11.04 on it. It use to run Windows Vista on a resolution of 1280x1024, so both my hardware and monitor support it. Now I'm on Ubuntu, but can only run 1024x768, and the screen is not that bright. Its like when you don't have the right drivers on a Windows machine. Now i'm new to linux, so I do not know what do do. I have an onboard Intel chipset i965. Maybe this is some useful information, I read something about it on a forum: lspci 00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 02) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) Can someone please tell me how I can get the screen better? saif@sodium:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9

    Read the article

  • Virtual Wifi Issue Windows 7

    - by Matt
    Lately I've been trying to use my laptop as a wireless router in my room. I have it connected to my school's network through ethernet, and I want to set up wireless so that I can use Wifi on my Android phone and iPod Touch. In the past, I used Connectify, but I started having an issue where my phone would find the network, connect, attempt to get the IP, and then suddenly the network would disappear. Then it'd pop up again, and the same process would happen over and over. I decided that I'd totally uninstall Connectify, but after that, neither Virtual Router Manager nor the command prompt could create a viable network either. My phone and even my iPod now encounter the same problem. Neither can successfully connect. So evidently there is something wrong with the laptop's virtual wifi feature, and I have no idea what that could be. I've tried enabling certain services that virtual wifi supposedly relies on, but some of them don't start, namely Remote Access Connection Manager. But I also have read that these enable on their own and that if they are normally not enabled it's fine. Furthermore, I even uninstalled and reinstalled the drivers for my wireless card. Any ideas as to why my virtual wifi won't function? Anything? I really would love to get this working...

    Read the article

  • lm-sensors - always returns 32 degrees (celsius) for temperature

    - by mopoke
    On my VIA EPIA motherboard (using VIA VT8231 ISA bridge), I get strange output for the lm-sensors temperature reading. It always returns 32 degrees (celsius). I have previously had correct output for temperature (my munin graphs show temperatures typically in the range of 50 to 60 degrees. I've tried uninstalling (and purging) the lm-sensors package, have re-run sensors-detect a number of times and rebooted but nothing seems to change the output. I am running Ubuntu Karmic Koala (9.10). Anyone got any bright ideas on what I might have missed? uname -a: Linux george 2.6.31-16-386 #53-Ubuntu SMP Tue Dec 8 06:39:34 UTC 2009 i686 GNU/Linux cpuinfo: processor : 0 vendor_id : CentaurHauls cpu family : 6 model : 7 model name : VIA Samuel 2 stepping : 3 cpu MHz : 399.000 cache size : 64 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu de tsc msr cx8 mtrr pge mmx 3dnow up bogomips : 800.04 clflush size : 32 power management: lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05) 00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP] 00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10) 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51) 01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a) sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +32.0°C (crit = +60.0°C)

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Openldap with ppolicy

    - by nitins
    We have working installation of OpenLDAP version 2.4 which is using shadowAccount attributes. I want to enable ppolicy overlays. I have gone through the steps provided at OpenLDAP and ppolicy howto. I have made the changes to slapd.conf and imported the password policy. On restart OpenLDAP is working fine and I can see the password policy when I do a ldapsearch. The user object looks like given below. # extended LDIF # # LDAPv3 # base <dc=xxxxx,dc=in> with scope subtree # filter: uid=testuser # requesting: ALL # # testuser, People, xxxxxx.in dn: uid=testuser,ou=People,dc=xxxxx,dc=in uid: testuser cn: testuser objectClass: account objectClass: posixAccount objectClass: top objectClass: shadowAccount shadowMax: 90 shadowWarning: 7 loginShell: /bin/bash uidNumber: 569 gidNumber: 1005 homeDirectory: /data/testuser userPassword:: xxxxxxxxxxxxx shadowLastChange: 15079 The password policy is given below. # default, policies, xxxxxx.in dn: cn=default,ou=policies,dc=xxxxxx,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE I do not what should be done after this. How can the shadowAccount attributes be replaced with the password policy.

    Read the article

  • SATA Blu-Ray drive not detected via USB adapter

    - by LTR
    I'm using an SATA blu-ray drive (Lite-On IHOS104), connected via a USB adapter to my Windows 7 (32-bit) notebook. The first time I plugged the adapter in, it worked perfectly. The drive appeared in Explorer, and my player software was able to play an encrypted Blu-Ray disc just fine. After the first reboot, it never worked again. Now it shows up as "removable media" with a size of 0 bytes, irregardless of whether a disk is inserted or not. The drive does not show up under the green "eject USB device" icon in the taskbar. The adapter is powered using a separate power adapter. I have tried: disconnecting all other USB devices testing with a DVD instead of a Blu-Ray disc letting Windows search for updated drivers for the drive - there are none using the same drive and adapter on another Win7 (but x64) computer. They work perfectly. using other USB ports on the same notebook - tried them all. using a different SATA/USB-adapter What else can I do to diagnose this problem?

    Read the article

  • Online resizing of kvm guest root filesystem?

    - by Bittrance
    I have a Linux guest that uses an LVM volume directly as root file system (that is, there is no partition table). libvirt config looks thus: <os> <type arch='x86_64' machine='rhel6.4.0'>hvm</type> <kernel>/boot/vmlinuz-X.Y.Z.el6.x86_64</kernel> <initrd>/boot/initramfs-X.Y.Z.el6.x86_64.img</initrd> <cmdline>console=ttyS0 root=/dev/vda</cmdline> <boot dev='hd'/> </os> <disk type='block' device='disk'> <driver name='qemu' type='raw' cache='none' io='native'/> <source dev='/dev/vg/guest'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> From inside the guest: $ mount /dev/vda on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) Is it possible to resize the guest's root partition without rebooting the guest? Just doing lvextend on the host and resize2fs from the guest does not seem to be enough.

    Read the article

  • [URGENT HELP PLEASE]USB Flash Drive Problem!

    - by Daren
    Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

    Read the article

  • Connecting XRAID to Sunfire via LSI FC card - Drives not showing up

    - by Matthew Watson
    Hi, I've got a Sunfire T1000 machine ( Solaris 10 10/09 s10s_u8wos_08a SPARC ) with a LSI7404EP-LC fibre channel card in it. This is plugged into an XRAID. The system seems to have picked up the card > /usr/platform/`uname -i `/sbin/prtdiag IO Location Type Slot Path Name Model ----------- ----- ---- --------------------------------------------- ------------------------- --------- MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/PCIE0 PCIE 0 /pci@780/fibre-channel fibre-channel MB/NET0 PCIE MB /pci@7c0/pci@0/network@4 network-pci14e4,1668 MB/NET1 PCIE MB /pci@7c0/pci@0/network@4,1 network-pci14e4,1668 MB/NET2 PCIX MB /pci@7c0/pci@0/pci@8/network@1 network-pci108e,1648 MB/NET3 PCIX MB /pci@7c0/pci@0/pci@8/network@1,1 network-pci108e,1648 MB/PCIX PCIX MB /pci@7c0/pci@0/pci@8/scsi@2 scsi-pci1000,50 LSI,1064 However it doesn't seem to be able to see the xraid attached to it, lsiutil only reports the onboard SAS controller. > /usr/local/bin/lsiutil ~ LSI Logic MPT Configuration Utility, Version 1.62, January 14, 2009 1 MPT Port found Port Name Chip Vendor/Type/Rev MPT Rev Firmware Rev IOC 1. mpt0 LSI Logic SAS1064 A3 105 010a0000 0 Select a device: [1-1 or 0 to quit] I've tried adding the configuration to /kernal/drv/sd.conf and /kernal/drv/ssd.conf as per this thread, however format still cannot see any drives on the xraid. I'm not sure where to go next. Any suggestions? From what I've read..this should pretty much just eb plug it in and they show up in format..

    Read the article

  • No signal on monitor after plug it to a linux box

    - by yaroot
    I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

    Read the article

  • Microsoft Windows DHCP: Steering IPv4 clients into specific scopes based on MAC

    - by Easter Sunshine
    We have visitors on our campus who bring their own laptops and devices and use our wireless and wired networks. When we receive a copyright infringement notice (typically BitTorrenting), we are required to quarantine that MAC address so that it no longer has Internet access. No matter what website it tries to visit, it is sent to a web page explaining to the user that the device has been quarantined. We have thus far implemented this in ISC DHCP on Linux. We have multiple VLANs with one or more public-IP subnets and one RFC1918 quarantine subnet each. All clients are leased IPs in the public-IP subnet(s) unless you're in a list of known bad MACs. Then, you are sent to the quarantine subnet so that your traffic is unroutable on the Internet (you are isolated by subnet only, not by VLAN). We would like to move to Windows DHCP in light of the IPAM role but I cannot figure out how to replicate this in Windows DHCP 2012 (Assign DHCP IPs for specific MAC prefixes on Windows Server 2008 R2 suggests it was not possible in 2008 R2), even while using policies. So here's what I'd like: The administrator/help desk provides and maintains a list of MAC addresses that are to be quarantined. The DHCP server places those MACs into the quarantine subnet on the respective VLAN, no matter which VLAN the client is in. I don't think reservations would work: We currently have about 300 registered bad MACs and about 12 VLANs. I don't want to make 300 x 12 reservations nor have to add 12 reservations per new MAC address. Not to mention all of the quarantine subnets are /24s. We do not have NPS/NAC. You do not have to register your MAC address get network access. We use Cisco routers/switches. Thanks.

    Read the article

  • Ubuntu lucid, maverick high iowait

    - by netom
    I'm using Ubuntu, and I've got the same problem with Lucid and Maverick. From time to time, especially a few minutes after boot, the iowait goes between 50-100% and the box is unusable. Everything that tries to access the disk freezes. I have the following setup: Hard disk: Model Family: Western Digital Caviar Green family Device Model: WDC WD15EADS-00P8B0 Serial Number: WD-WMAVU0391287 Firmware Version: 01.00A01 User Capacity: 1.500.301.910.016 bytes I have a quad core Intel Core2 Q6600 processor, and 4G of memory. When the high iowait occurs, usually 4 processes are active: kdmflush (two procs) jbd2/dm-0-8 jbd2/db-1-8 and a few more starving user processes of course. I know this from top and iotop. Any suggestions about why this is happening? There are a lot of q/a-s about linux and high iowait, but none of them helped so far, I even tweaked the hard disk not to park the head in every 8 seconds (Load cycle count is 50334!!!!! :o ), but nothing. Problem persists. Thank you in advance.

    Read the article

  • Best way to 'harden' embedded ext4 file server against unexpected loss of power?

    - by Jeremy Friesner
    Hi all, First, a little background: my company makes an audio streaming device that is a headless, rack-mounted Linux box with a couple of SSDs attached. Each SSD is formatted with ext4. The users can connect to the system using Samba/CIFS to upload new audio files or access existing ones. There is also custom software for streaming out audio over the network. This is all fine. The only problem is that the users are audio people, not computer people, and see the system as a 'black box', not as a computer. Which means that at the end of the day, they aren't going to ssh in to the box and enter "/sbin/shutdown -h"; they are just going to cut power to the rack and leave, and expect things to still work properly the next day. Since ext4 has journalling, journal checksumming, etc, this mostly works. The only time it doesn't work is when someone uploads a new file via Samba and then cuts power to the system before the uploaded data has been fully flushed to the disk. In that case, they come in the next day and find that their new file has been truncated or is missing entirely, and are unhappy. My question is, what is the best way to avoid this problem? Is there a way to get smbd to call "sync" at the end of every upload? (Performance on uploads isn't so important, since they only happen occasionally). Or is there a way to tell ext4 to automatically flush within a few seconds of any change to a file? (Again, performance can be sacrificed for safety here) Should I set a particular write-ordering mode, activate barriers, etc?

    Read the article

  • Stream video from a computer to a tablet

    - by NullOrEmpty
    I would like to watch presentations and college videos I have on my computer, from my tablet. There are almost a hundred of GB in videos, so I would like to watch them in streaming from my computer. My wife has also tons of videos so I have decided to do a kind of streaming local service to watch the videos from our tablets. I have found an article about how to do it with Internet Information Server, but the article is relaying in an application that is not free (Expression Encoder). Since this is for home fun, I am not willing to pay, so I would like to ask for some free encoder that can do the trick. I have no idea about streaming. Actually, I tried to hang the files directly on IIS, and the browser tried first to download some of them and some other (mp4?) got played badly, so I could not get a smooth video experience. What is missing? What is the deal with H.264 ? Can I roll with VC-1 and play videos in my Android tablet with streaming with an acceptable quality through my WLAN home network? Any better solution? Thanks.

    Read the article

  • best-practices to block social sites

    - by adopilot
    In our company we have around 100 workstation with internet access, And day by day situation getting more worst and worst from perspective of using internet access for the purpose of doing private jobs, and wasting time on social sites. Open hearted I am not for blocking sites like Facebook, Youtube, and others similar but day by day my colleagues do not finishing his tasks and while I looking at their monitor all time they are ruining IE or Mozilla and chat and things like that. In other way Ill like to block youtube sometime when We have very poor internet access speed, Here is my questions: Do other companies blocking social sites ? Do I need dedicated device for that like hardware firewall, super expensive router Or I can do that whit my existing FreeBSD 6.1 self made router with two lan cards and configured nat to act like router. I was trying do that using ipfw and routerfirewall but without success, My code looks like ipfw add 25 deny tcp from 192.168.0.0/20 to www.facebook.com ipfw add 25 deny udp from 192.168.0.0/20 to www.facebook. ipfw add 25 deny tcp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny udp from 192.168.0.0/20 to www.dernek. ipfw add 25 deny tcp from 192.168.0.0/20 to www.youtube. ipfw add 25 deny udp from 192.168.0.0/20 to www.youtube.com

    Read the article

  • How do I create a wifi network bridge with qemu on OS X?

    - by a paid nerd
    I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

    Read the article

  • Dual boot windows 8 pro and windows 7 on XPS 8500 Special Edition

    - by Jesse
    I am trying to install a dual boot with windows 7 premium and windows 8 Pro on an XPS 8500 special edition. I created a new primary partition on my C: drive, inserted the windows 8 install disk, and rebooted my computer from DVD. I select custom install and the dialog box saying "Where do you want to install windows at?" pops up but none of my drives are listed. Please help me determine what is going on. I don't understand why none of my drives are showing up on this menu. Not even the original drive. When I go to load driver and click on the partition I created it tells me "No signed device drivers were found. Make sure the installation media contains the correct drivers, and then click OK." resolved above issue by running setup from the source folder on the install disk instead of booting from DVD. Was able to locate my new partition and start install. It completes the first step of "Copying windows files" just fine but then on the next step "Getting files ready for installation" my computer restarts and attempts to load windows 8 but keeps telling me my pc needs to restart. This keeps going on in an infinite boot loop. Please help, this has been a nightmare!

    Read the article

  • Shadow copy referencing invalid volume from symboliclink

    - by ccook
    I recently replaced my motherboard after the last one failed (was shorting and causing random reboots). I'm sure this was not healthy for the machine, and that a clean install would do wonders, but I'd like to fix the current install. That aside, I've been tracking down a pair of errors in the application log. Volume Shadow Copy Service error: Error calling a routine on a Shadow Copy Provider {b5946137-7b9f-4925-af80-51abd60b20d5}. Routine details IVssSnapshotProvider::QueryVolumesSupportedForSnapshots(ProviderId,29,...) [hr = 0x80042302, A Volume Shadow Copy Service component encountered an unexpected error. Check the Application event log for more information. ]. Operation: Query volumes supported by this provider Context: Provider ID: {b5946137-7b9f-4925-af80-51abd60b20d5} Snapshot Context: 29 Followed by Volume Shadow Copy Service error: Unexpected error calling routine Error calling CreateFile on volume '\?\Volume{f4bda86e-049d-11e1-9255-bcaec56690a1}\'. hr = 0x80070020, The process cannot access the file because it is being used by another process. This error is reproducible at command line, creating the two event log entries C:\Windows\system32>vssadmin list volumes vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool (C) Copyright 2001-2005 Microsoft Corp. Error: The shadow copy provider had an unexpected error while trying to process the specified command. Using WinObj from Sysinternals, I have tracked down the global object. '\?\Volume{f4bda86e-049d-11e1-9255-bcaec56690a1}\' - SymbolicLink - '\Device\HarddiskVolume8' Running DISKPART, and running the command "list volume" within it lists volumes 0 through 6, there is not a HarddiskVolume8. How can I remove this reference to HarddiskVolume8, and get shadow copy up and running?

    Read the article

  • Starting airplay from command line, to send output of 'Say' Mac OS X command to airplay

    - by Fabien
    Ok, Sunday question :) Trying to make a little joke... 1) if you open a terminal, and type "say -a ?", Mac OS X will give you the list of devices it can send spoken words to. On mine, it says: 39 AirPlay 47 Built-in Output 2) I have a Denon airplay-ready received in my living room and I'm trying to send spoken words to my wife downstairs... I can send music without any problem using iTunes so, from an infrastructure standpoint, I'm all set. 3) I want my computer to say (out of the blue) "Honey, why don't you bring me a cup of coffee". I can make it say that locally on my internal laptop speakers, but I can't seem to send that to device 39 successfully. I am suspecting that there are a few other things that need to be setup before it works, i.e. setting up airplay output to "denon", maybe opening a channel and reserving it. I don't know. Has anyone played with this? Is there a way to setup airplay from the command line? That would be awesome :)

    Read the article

< Previous Page | 757 758 759 760 761 762 763 764 765 766 767 768  | Next Page >