Search Results

Search found 23062 results on 923 pages for 'multiple models'.

Page 772/923 | < Previous Page | 768 769 770 771 772 773 774 775 776 777 778 779  | Next Page >

  • Hostname vs webpage domain.

    - by Mark
    Hi All, Im just starting to look at deploying a webpage and get into the joy of DNS etc. And im wondering how you set up multiple web-servers all with thier own hostnames/public IP addresses, and yet have them serve up a webpage from one domain. For example, lets say you have a website example.com, and an A record in DNS that points at it's IP address of 1.2.3.4 . You want to have two servers, prod1 and prod2 with some kind of load balancer in front of them for fail over reasons. The way I see it you would want to have the hostnames of these servers as prod1.example.com and prod2.example.com and perhaps loadb.example.com. How would you set up the DNS so this would all work. ie you could ssh to any of the server domains, prod1.example.com, prod2.example.com or loadb.example.com and also just use the www.example.com url to go to the website. And would all these server names be resolvable from the public internet and is that safe? This would be a linux environment, for arguments sake ubuntu, a django framework dynamic website, running in apache 2.2 Cheers Mark

    Read the article

  • Website latency and bad tcp packets

    - by Mistero Lupo
    I have multiple websites hosted on a Linode VPS and I'm having an issue with one of them: every page that I try to load has about 10 seconds latency. Apache logs are clean and the other websites on the same machine are running well. At a first glance I tought it was a memory problem since the VPS has got only 512M, but from the linode dashboard CPU and Disk I/O are normal. Anyway here we have the ram status: $ free -m total used free shared buffers cached Mem: 487 463 23 0 2 55 -/+ buffers/cache: 404 82 Swap: 255 155 100 Only 23M free, but if it was a memory problem why other websites are going as usual? I took a live capture with wireshark, and there are some duplicates SYN ACK packets just before the 10 seconds gap. I'm out of ideas, looking for some clues. Wireshark live capture screenshot As you can see from the image, the gap is after the last bad tcp. Thank you in advance. UPDATE I've checked Apache2 logs in debug error level, and this is where something is appening: 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'index.php' 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (1) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] pass through /home/fmaisi/sites/www.fmaisi.it/public_html/index.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] strip per-dir prefix: /home/fmaisi/sites/www.fmaisi.it/public_html/wp-content/plugins/wp-filebase/wp-filebase_css.php -> wp-content/plugins/wp-filebase/wp-filebase_css.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'wp-content/plugins/wp-filebase/wp-filebase_css.php' As you can see there is a gap of 14 seconds after the pass through of index.php. Any suggestions? I'm out of ideas again.

    Read the article

  • Interaction between two Clouds

    - by Snehal Masne
    I have setup the Cloud-A with 1 - [CLC+CC] and 2 - [NC] computers. I have another Cloud-B with same configuration using the Ubuntu Enterprise Cloud Both of them working fine individually, in the same LAN. Now if I want to add the NC of Cloud-A to CC of Cloud-B, [in case the resources of Cloud-B are exhausted] how can I make it possible ? I guess this calls for the interoperability stuff... Could you please explain what happens exactly when we ask for instance, the direct interaction happens between the client and NC or it goes through the CLC and CC ? What I want to say is, say there are multiple cloud providers. A user is subscribed to any one of them, say Cloud-A for IaaS. As the requirements are dynamic, all the resources of Cloud-A may get exhausted. There may be another Cloud-B which can provide the services but that Cloud-A can't ask the client to go for Cloud-B. So if it is possible to have some co-ordination between this two providers to share resources mutually, making client fully unaware of whats going on in the background....?

    Read the article

  • Limited bandwidth and transfer rates per user.

    - by Cx03
    I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

    Read the article

  • "Document in ADF" on Canon MX340

    - by Michael Donohue
    I have a Canon MX340 multifunction printer. Recently, it keeps saying "Document in ADF" when I turn on the printer. I've tried clearing this multiple times, but as soon as the feeder wheels stop turning, in an attempt to clear the document feeder, it just pops up the same error again. This is particularly annoying, as it blocks all functions on the device - I cannot print, even though printing has no interaction with the document feeder. I've opened up the feeder device, as much as can be done with fingers alone. There just doesn't seem to be anything in there. I ran a sheet of paper through about six times, just to see if some dust might be getting in the way, and I've blown out the feeder with air. Still nothing. At this point, I don't care too much about the ADF working, I just want to disable whatever sensor is tripping this error message. Any ideas? I found this thread online, where a user has the same problem. But no resolution was reached there.

    Read the article

  • Replicated filesystem and EC2 MySQL

    - by El Yobo
    I'm currently investigating migrating our infrastructure over to run on Amazon's EC2 and am trying to figure out the best way to set up a MySQL service. I'm leaning towards running our own MySQL instances, rather than going with Amazon's RDS, but am still considering the best approach for performance and cost on the instance itself. In order to have persistent data, the MySQL data needs to be on an EBS volume (with some form of striped RAID, e.g. RAID0 or RAID10) to improve persistence. However, EBS IO is limited by the network interface (gigabit, so a theoretical maximum of 128 MB/s), while the ephemeral volumes have no such problem. I did see a suggestion for running two MySQL servers on an instance, with a master running on the ephemeral disk (which we would also RAID) and a slave storing changes to an EBS volume, but this has some additional overhead and complexity (two servers). What I was imagining is using some form of replicated file system such that I could have a filesystem on top of a RAID0 of ephemeral volumes to maximise performance all changes from the above immediately replicated to another RAID1 volume backed by multiple EBS volumes to ensure no data loss The advantages of this would be best possible IO performance for the DB server; no network delay in IO decreased IO on EBS volumes (as all read IO will be done on the ephemeral volumes) so decreased cost good data security, as it's backed onto redundant EBS volumes However, I haven't seen an appropriate system to replicate all changes from one volume to the other; is there a filesystem, or any other approach, which will do this? The distributed file systems, e.g. GlusterFS, DRBD etc seem to focus on replicating disks between servers, can they be set up to do what I'm interested in here? I also haven't seen anything about other's taking this approach. Do I have a solution in need of a problem here (i.e. is performance good enough, so this whole idea is redundant)? Is there some flaw in the plan?

    Read the article

  • Can't access certain web sites - reset router, any ideas?

    - by IniTech
    EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

    Read the article

  • Graphics artifacts/distortion with Win7 and nVidia

    - by Gepard
    Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

    Read the article

  • Remote Desktop leaves host unresponsive

    - by Jeff Dalley
    I have my desktop PC at home set up to accept remote connections, and I often connect to it from work on my laptop via mstsc.exe. However, every time I remote to it, I find when I go home that despite the monitor being on - it's not receiving an image and it looks as though the computer is hibernating/asleep. I basically have to restart it whenever I get home and I know there's an answer for why its doing this. More details: When exiting the remote session, I have tried both logging off the account, and closing the RDP window without logging off; both give the same result. When I get home to the desktop I of course try moving the mouse, ctrl+alt+del to see if its responsive to restart, multiple key-press to see if I can get any audio out of it; It seems pretty obvious its sleeping/hibernating in some way: Nothing happens in any of these cases and a physical restart is necessary. Both desktop and laptop are running Windows 7 Ultimate. I'm thinking it really is sleeping/hibernating it, and I'm not sure why because left alone my desktop's power options are set to never turn off the HDD or change its state - I leave it on 24/7. This could be a stupid error on my part but I just can't see it! Thanks.

    Read the article

  • Many clients on a wireless AP for UDP broadcast packets

    - by distorteddisco
    I asked this question on StackOverflow and was directed over here, so I'd appreciate any advice. I'm deploying a smartphone application as part of a live music performance that depends on receiving UDP broadcast packets from a wireless access point. I'm guessing that between 20 and 50 clients will be connected at any one time. I'm aware that a maximum of 20 clients per access point is advised, but as the UDP broadcast packets are ground through the LAN, how would I be able to link multiple APs together? I'm looking for recommendations on a suitable AP for this. The actual data transmission rates are very low - only a few kB/s - as I'm just sending small messages to the smartphone apps, and there will be no WAN internet connection. I tried it with a few connected peers on an adhoc wireless connection without any problems, but ran into dropped packet issues on an old WRT54G running ddwrt, though it's in pretty rough shape. What's the best way to do this? I suppose I could limit concurrent wireless connections to 20 clients... but more would be nice. EDIT: I should also say that it's purely one-way communication; the smartphone application is only receiving broadcast packets, not sending anything.

    Read the article

  • Unnamed, hidden partitions on my 500 GB HD, HP Pavilion dm4 Laptop

    - by emotionull
    I have multiple doubts here. Its a Seagate 500GB 7200RPM HD. I had installed it few months back after my original Laptop HD stopped working. The current drives on my latop, as shown by the Windows Disk Management are: After installing the new HD, I had done a complete clean install of Windows 7 and I didn't create any parition myself, manually. So there are 4 drives. Even previously, before I installed this new HD, my laptop had 4 Partitions. But the there were no un-named partitions like the two in this case. The other two were HP tools and Recovery or something. It was pre-configured, Factory installed Windows. Also, now when I right cick on the unnamed Drives from Disk Management, all the options are greyed out (see image) except the delete partition image. So how do I know what's inside those partitions? Will it be ok if I delete them? I want install Ubuntu and dual boot it with my current windows installation. I cannot do it in current setup as there are already 4 partitions of my HD and if I will try to make a new partition, it will be a logical one (correct me if I am wrong here). So can I delete the un-named, hidden partitions and use them for Ubuntu? A bit unrelated question. As a backup option, can I use the Windows 7's Backup and Restore facility to keep a complete backup of all the drivers and system softwares.

    Read the article

  • Why Are SPF Records Failing?

    - by robobobobo
    Ok I've been going through various different sites, resources and topics here trying to figure out what is wrong with my SPF records but no matter what I do they don't seem to pass. Here's what I have "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" I've tried multiple different tools to check my spf records, some give me a pass, some don't. But I can't send mail to certain google app accounts, they just bounce back all the time which is very annoying. Anyone got any ideas? I have noticed that the source IP address is not the IPV4 addresses I've defined, but Cpanel wouldn't let me add that address into it.. And here's the result of tests I'm getting back from port25.com. I'm running WHM by the way and have enabled spf and dkim. Summary of Results SPF check: fail DomainKeys check: neutral DKIM check: pass Sender-ID check: fail SpamAssassin check: ham Details: HELO hostname: server1.viralbamboo.com Source IP: 2a01:258:f000:6:216:3eff:fe87:9379 mail-from: ###@viralbamboo.com SPF check details: Result: fail (not permitted) ID(s) verified: smtp.mailfrom=###@viralbamboo.com DNS record(s): viralbamboo.com. SPF (no records) viralbamboo.com. 13180 IN TXT "v=spf1 +a +mx +ip4:217.78.0.92 +ip4:217.78.0.95 -all" viralbamboo.com. AAAA (no records) viralbamboo.com. 13180 IN MX 0 viralbamboo.com. viralbamboo.com. AAAA (no records) DomainKeys check details: Result: neutral (message not signed) ID(s) verified: header.From=###@viralbamboo.com DNS record(s): DKIM check details: Result: pass (matches From: ###@viralbamboo.com). ID(s) verified: header.d=viralbamboo.com Canonicalized Headers: content-type:multipart/alternative;'20'boundary="4783D1BE-5685-41CF-B91B-1F15E91DD1E3"'0D''0A' date:Mon,'20'1'20'Jul'20'2013'20'21:30:47'20'+0000'0D''0A' subject:=?utf-8?Q?test?='0D''0A' to:"[email protected]?="'20''0D''0A' from:=?utf-8?Q?Rob_Boland_-_Viralbamboo?='20'<###@viralbamboo.com'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=viralbamboo.com;'20's=default;'20'h=Content-Type:Date:Subject:To:From:MIME-Version;'20'bh=CJMO7HYeyNVGvxttf/JspIMoLUiWNE6nlQUg5WjTGZQ=;'20'b=;

    Read the article

  • Wildcard subdomain setup ... want to change host IP throws off client A records... what to do...

    - by Joe
    Here is the current set up (in a nutshell). The site is set up with a wildcard subdomain, so *.website.com is accessible. Clients can then domain map their own domains with an A record to the server IP address and it will translate the to appropriate *.website.com with re directions and env variables in htaccess. Everything is working perfect... but now comes the problem. The site has grown larger than a single DQC Xeon server can handle at peak times. Looking at cloud options seems tempting, but clients are pointing their domains to a single IP address with the A record (our server). Now, this was probably bad planing from the start, but the question is, if this was to be done today, how would we set it up so that clients use a CNAME perhaps to point their domains to our server rather than an A record. And, if that is not possible for the root domain, how can we then use multiple IP addresses on our side to translate the incoming http request? Complex enough? Hope I've explained it well!

    Read the article

  • Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

    - by Brandon Bearden
    Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

    Read the article

  • How to set up a server without a hosting control panel

    - by A4J
    I have always used a control panel on my dedicated servers - from cPanel to Plesk to Virtualmin, and I am now considering ditching a CP altogether and manually editing config files. My requirements are fairly simple, I will host multiple sites on the server; some Apache with PHP & Mysql and some Passenger with Rails & Postgres. All will require email smtp/pop. FTP/Stats will not be required. Could someone please give me a quick run-down of what I would need to do - in terms of installing software and configuration? My server will come with a base install of CentOS 6.4 minimal. My thoughts so far: Install/update latest versions of MySQL & Postgres (are they 'safe' out of the box? Or do I need to do anything else like set up root passwords etc?) Install Apache & PHP (again, are the base installs good to go or do they require security tweaks?) Set up nameservers/hostnames/reverse DNS etc (Any guides on how to do this please?) Install Rubygems Install and configure Dovecot and Postfix (any tips on doing this? Or links to how-tos that cover it please?) Set up each website - any links to guides on how to do this? Install/configure firewall (or is the default install good to go?) Any other tips or advice would be greatly appreciated, as would links to guides or how-tos.

    Read the article

  • Is there a way to use VirtualBox without using it's resource registry?

    - by Catskul
    Summary VirtualBox seems to want everything to be "registered" which makes it much more annoying to work with on the command line. I'm attempting to create an automated script which will create, move, start, stop, and destroy virtual machines and virtual disks. Requiring registration will complicate the task for the following reasons. leaves state information around that can cause unpredicted edgecases causing scripts to fail. creates potential name space collisions for multiple process creating VMs with the same name moving/copying resources on the same machine is more complicated because references in the registry need to be updated copying resources (disk + vm combination) to another machine require reconfiguration once they reach their target machine, and require the transfer of extra meta data to do the reconfiguration. If something unexpectedly fails, and an unregister thus fails to happen, left over configuration information can cause problems in subsequent runs. Use Case My specific use case is for a continuous integration server which creates and destroys VMs and Disk images potentially with the same name, and would require more logic to deal with the registry's statefulness. Imaginary Example It seems that I should just be able to for example (using some imaginary and/or incorrect commands): mkdir foobar customdiskimg_script ./foo/foo.vdi vboxmanage createvm --name "foo" --ostype Linux --basefolder ./foo/foo.xml vboxmanage storagectl ./foo/foo.xml --name foo --add ide vboxmanage storageattach --storagectl foo --medium ./foo/foo.vdi ./foo/foo.xml vboxmanage startvm ./foo/foo.xml TLDR Is there a way to use virtualbox without "registering" harddisks and VMs?

    Read the article

  • Security Token for Mac/Linux/Windows, self-managed, pref. open source?

    - by DevelopersDevelopersDevelopers
    I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

    Read the article

  • Enterprise Redirection Services?

    - by Aaron Alton
    This is probably a case of "if I new what it was called, I could google it in 5 minutes" - but I don't know what it's called. It's probably best to explain the requirement using an example. We have a number of services (vpn, owa, etc) which we host from one of our datacenters. We have a number of datacenters, and we technically have the infrastructure already in place to support these services at a number of our datacenters. To provide access to these "services", I would create an external DNS entry (ex. VPN.MyCompany.com Gateway IP for one of my DCs), and clients will connect to it via the DNS entry. Since I have multiple datacenters that can support this service, I could theoretically offer a "highly available, geographically dispersed" solution if I could point this DNS entry to some sort of third party who offers highly available "redirection" services. If my primary site goes down, I could just make a change via some management console and configure the redirector to point to a different DC. Of course, it would be fairly straightforward to set this sort of thing up on one of our servers, but that would kinda defeat the purpose of a highly available third party. Is anyone familiar with a service like this? I'm thinking something like DynDNS, but with Enterprise availability guarantees.

    Read the article

  • Wipe free space on LVM-LUKS (dm-crypt) Volume

    - by peter4887
    My three partitions for my system are created with LVM on a LUKS partition (dm-crypt). These are /home, / and swap. The filesystem is ext4. They are encrypted, because they are on my laptop and I don't want that some laptop thieves get my data. But I often share my laptop with other people so they can access my encrypted partitions. I don't want that these people can recover my cache and all the data I deleted. So I'm now trying to wipe all my free space on /home to prevent against recovering with tools like photorec. (one overwrite should do, the need of multiple overwriting is just a rumor) But still I haven't found any solution to wipe this free space successfully. I tried dd if=/dev/zero of=/home/fillitup bs=512 count=[count of free sectiors] so my partition was complete full of data. df /dev/mapper/home said 100% is used and there are 0 sectors available. But I could still recover gigs of data with photorec, although I selected to recover just form the free space. photorec displays: /dev/mapper/home - 340 GB / 317 GiB (RO) , but df displays that the size of /home is just 313G, why are there these differences and what did the 340GB means? It looks like there is a place on my /dev/mapper/home partition, that I can't access to overwrite, but I can access it to recover. I also checked for corrupted sectors, but there aren't any. Maybe this is the space between my existing files? Did anyone knows why I can't wipe my free space with dd, and how I can find the location of the loads of recoverable files, to securely delete them?

    Read the article

  • Moving from 1 Linux Partition to Many over USB Mount

    - by Mistiry
    We have devices which use Compact Flash for storage. They work OK, but we recently got industrial-grade CF cards to start using. One of the major problems we get is corruption on the flash card. As it is now, these flash cards run Debian with everything in a single partition. We want to have multiple partitions on the new industrial CF cards to help avoid some of the corruption problems. I booted up the device, and attached a USB CF reader. I then used fdisk to partition the CF card in the USB reader. How can I move the data to these partitions so that it works? I have a partition for each of these directories: /lib /var /root /boot /tmp /home /etc / swap space I imagine I can't just use rsync - do I need to attach a second CF reader with a copy of the CF card, so that it's not active and in-use - and then copy from the first reader to the second? How will the system know where to find its files? I know I'd have to change fstab, but that resides in /etc, which will be on a separate partition...how will it find the fstab file if it can't find /etc? And what about grub? I'm at a loss, perhaps its just because I'm under the weather, or I'm just missing a piece of logic here... Any help is greatly appreciated, this is somewhat urgent as our existing stock is nearing its end and we don't want to purchase anything but these industrial cards, but need to get it working with partitions.

    Read the article

  • Best solution top keep data secure

    - by mrwooster
    What is the simplest and most elegant way of storing a small amount of data in a reasonably secure way? I am not looking for ridiculous levels of advanced encryption (AES-256 is more than enough) and I am only looking to encrypt a small number of files. The files I wish to encrypt are mostly comprised of password lists and SSH keys for servers. Unfortunately it is impossible to keep track of ever changing passwords for my servers (and SSH keys) and so need to keep a list of the passwords. Obviously this list needs to be secure, and also portable (I work from multiple locations). At the moment, I use a 10MB encrypted disk image on my mac (std .dmg AES-256) and just mount it whenever I need access to the data. To my knowledge this is very secure and I am very happy using it. However, the data is not very portable. I would like to be able to access my data from other machines (especially ones running linux), and I am aware that there are quite a few issues trying to mount an encrypted .dmg on linux. An alternative I have considered is to create a tar archive containing the files and use gpg --symmetric to encrypt it, but this is not a very elegant solution as it requires gpg to be installed on every system. So, what over solutions exist, and which ones would you consider to be the most elegant? Ty

    Read the article

  • What is the risk of introducing non standard image machines to a corporate environment

    - by Troy Hunt
    I’m after some feedback from those in the managed desktop or network security space on the risks of introducing machines that are not built on a standard desktop image into a large corporate environment. This particular context relates to the standard corporate image (32 bit Win XP) in a large multi-national not being suitable for a particular segment of users. In short, I’m looking at what hurdles we might come across by proposing the introduction of machines which are built and maintained by a handful of software developers and not based on the corporate desktop image (proposing 64 bit Win 7). I suspect the barriers are primarily around virus definition updates, the rollout of service packs and patches and the compatibility of existing applications with the newer OS. In terms of viruses and software updates, if machines were using common virus protection software with automated updates and using Windows Update for service packs and patches, is there still a viable risk to the corporate environment? For that matter, are large corporate environments normally vulnerable to the introduction of a machine not based on a standard image? I’m trying to get my head around how real the risk of infection and other adverse events are from machines being plugged into the network. There are multiple scenarios outside of just the example above where this might happen (i.e. a vendor plugging in a machine for internet access during a presentation). Would a large corporate network normally be sufficiently hardened against such innocuous activity? I appreciate the theory as to why policies such as standard desktop images exist, I’m just interested in the actual, practical risk and how much a network should be protected by means other than what is managed on individual PCs.

    Read the article

  • Developing high-performance and scalable zend framework website

    - by Daniel
    We are going to develop an ads website like http://www.gumtree.com/ (it will not be like this one but just to give you an ideea) and we are having some issues regarding performance and scalability. We are planning on using Zend Framework for this project but this is all that I'm sure off at this point. I don't think a classic approch like Zend Framework (PHP) + MySQL + Memcache + jQuery (and I would throw Doctrine 2 in there to) will fix result in a high-performance application. I was thinking on making this a RESTful application (with Zend Framework) + NGINX (or maybe MongoDB) + Memcache (or eAccelerator -- I understand this will create problems with scalability on multiple servers) + jQuery, a CDN for static content, a server for images and a scalable server for the requests and the rest. My questions are: - What do you think about my approch? - What solutions would you recommand in terms of servers approch (MySQL, NGINX, MongoDB or pgsql) for a scalable application expected to have a lot of traffic using PHP?...I would be interested in your approch. Note: I'm a Zend Framework developer and don't have to much experience with the servers part (to determin what would be best solution for my scalable application)

    Read the article

  • Laptop keyboard stopped functioning properly

    - by galdikas
    Basically today out of blue my laptop keyboard started acting up. For example I press "s" but I see "`s" on the screen. Some keys don't work at all. And the weird thing is it keeps changing, in a sense that for example in the morning I press "s" and I get "`s", then few hours later "s" works correctly.. but pressing some other key output multiple characters. Then sometimes it spontaneously will start outputting some character onto any input field that is available as soon as I click on it to gain focus. And it will just keep on going and going, as if I keep a button pressed (which I don't). At first I thought this was a virus, but I have a dual boot of Windows 7 and Ubuntu, and I get same problem on both. I even tried to boo live CD, and still had same problem. Anyone had this kind of problem? It's a Toshiba Satellite c660-258. It is around year old, but quite well kept. Never spilled anything on it, or dropped it. And my wireless USB keyboard works perfectly on it (appart from the spontaneous character inputs, which I can stop by hitting NUM LOCK key)

    Read the article

  • What needs to be considered when setting up for Linux Development? [closed]

    - by user123586
    I want to set up a box for Linux development. I have a working linux install with the usual toolchain and an IDE. I'm looking for advice on how to approach structuring accounts and folders for development. As the Perl folks say "There's always more than one way to do it." Left to my own devices, I'll come up with several unproductive ways of doing it before figuring out what an experienced Linux programmer would think obvious. I'm not looking for instructions to follow for a specific set of tools or a specific software package. Instead, I'm looking for insight into what decisions need to be made and how to make them, with understanding of the advantages and disadvantages of each individual choice. These are some of the questions that come up: Where to put sources Where to put built object files and libraries where to install what to set in environment variables what compiler flags matter and how do you manage them across several types of builds what configuration entries to make in an IDE how to manage libraries to support multiple environments how to handle different build versions such as debug vs release, or cross platform builds If you are an experienced Linux developer, the answers to these questions may seem trivial and obvious. I'd like to learn to make decisions about these questions that result in as little manual configuration as possible, given some existing sources, a particular IDE, or no IDE at all, a paticular set of development libraries etc. At this point you're probably thinking: Can you be more specific? Sure. But remember that I'm trying to learn how to think about this stuff, not just follow a recipie for a specific set of results. Example: Setup a project that uses CMake for some of its components, autogen.sh followed by configure for others and just configure for a few more: debug builds without an IDE debug builds in NetBeans debug builds in Eclipse debug build in Visual Studio all of the above with release builds for Linux, Mac and Windows. So... **What are your thoughts on an approach that works for all four? Do you have any advice on what to read?**

    Read the article

< Previous Page | 768 769 770 771 772 773 774 775 776 777 778 779  | Next Page >