Search Results

Search found 25400 results on 1016 pages for 'enable manual correct'.

Page 774/1016 | < Previous Page | 770 771 772 773 774 775 776 777 778 779 780 781  | Next Page >

• Wake On Lan only works on first boot, not sequent ones

  - by sp3ctum

  I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

  Read the article

• Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

  - by jamieb

  I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

  Read the article

• Cannot change PostgreSQL port

  - by Jerec TheSith

  I run Postgresql 8.4 as a service on a CentOS 6.2 server. I set port = 21444 and listen_addresses = '*' in /var/lib/pgsql/data/postgresql.conf and I changed 5432 to 21444 in postmaster.opts and restarted postgres, but when I run netstat -lntp postgresql is still running on port 5432 tcp 0 0 0.0.0.0:5432 0.0.0.0:* LISTEN 20276/postmaster When I restart postgresql I get a writting error warning on /proc/self/oom_adj, but the service starts anyway. I read that we could get this error when using virtualized servers, but I don't really know if this has inpact on postgresql listening port. The correct pgsql config file is loaded in /var/lib/pgsql/data : [root@srv02 ~]# ps -ef | grep postgres root 1358 22140 0 09:42 pts/0 00:00:00 grep postgres postgres 9519 1 0 Mar16 ? 00:00:01 /usr/bin/postmaster -p 5432 -D /var/lib/pgsql/data postgres 9573 9519 0 Mar16 ? 00:00:00 postgres: logger process postgres 9575 9519 0 Mar16 ? 00:00:05 postgres: writer process postgres 9576 9519 0 Mar16 ? 00:00:03 postgres: wal writer process postgres 9577 9519 0 Mar16 ? 00:00:01 postgres: autovacuum launcher process postgres 9578 9519 0 Mar16 ? 00:00:01 postgres: stats collector process any thought ? thanks, Jerec

  Read the article

• Replacing all disks in a non-OS RAID 5 volume

  - by molecule

  Hi all, We currently have a server with 8 x HDD slots. It is a HP DL380G5 with a P400 controller. 2 x HDD are in a RAID 1+0 config and this hosts the OS. 6 x HDD are in a RAID 5 config and holds an Oracle DB. Basically the RAID 5 volume is running out of space and we would like to swap all 6 with higher capacity disks. Excuse my ignorance as I am pretty new to this... I believe we will need to backup the data, delete the RAID volume, insert the new disks, recreate the volume, and restore the data. 2 questions: Do we need to worry about the OS partition or is it completely independent so we can simply take out the 6 and insert 6 new disks and get the controller to recognize the 6 new disks and form a new RAID 5 volume? We should not need to reinstall OS or Oracle correct? Since we are going to restore the data on the volume from another source (our vendor will take care of this) but we would like to keep the existing data on the 6 disks just in case we run into issues and want to fall back, is this possible? Thanks in advance.

  Read the article

• Windows Server task manager displays much higher memory use than sum of all processes' working set s

  - by Sleepless

  I have a 16 GB Windows Server 2008 x64 machine mostly running SQL Server 2008. The free memory as seen in Task Manager is very low (128 MB at the moment), i.e. about 15.7 GB are used. So far, so good. Now when I try to narrow down the process(es) using the most memory I get confused: None of the processes have more than 200MB Working Set Size as displayed in the 'Processes' tab of Task Manager. Well, maybe the Working Set Size isn't the relevant counter? To figure that out I used a PowerShell command [1] to sum up each individual property of the process object in sort of a brute force approach - surely one of them must add up to the 15.7 GB, right? Turns out none of them does, with the closest being VirtualMemorySize (around 12.7 GB) and PeakVirtualMemorySize (around 14.7 GB). WTF? To put it another way: Which of the numerous memory related process information is the "correct" one, i.e. counts towards the server's physical memory as displayed in the Task Manager's 'Performance' tab? Thank you all! [1] $erroractionpreference="silentlycontinue"; get-process | gm | where-object {$.membertype -eq "Property"} | foreach-object {$.name; (get-process | measure-object -sum $_.name ).sum / 1MB}

  Read the article

• Motherboard running rather hot while gaming

  - by I take Drukqs

  Case: Antec 1200 Mobo: Gigabyte GA-X58A-UD3R CPU: Intel i7 950 (stock cooler) GPU: EVGA GeForce 570 GTX RAM: 2x 2 GB (4 GB total) DDR3 dual-channel Corsair OS: Windows 7 Home Premium 64-bit This is my first build and it's brand new. I had no problems putting it all together in a few hours one evening and I consider myself to be pretty good with computers. Not to brag or anything like that! Just saying I've been fiddling with them since I was in diapers and I have a good amount of experience under my belt, just not with certain things yet. Recently while playing many of the latest games maxed out without a hitch my motherboard has been running hot and like anyone who's ever built a computer it scares the life out of me. I checked HWMonitor and saw that my motherboard sometimes reached temperatures of around 52 - 78c (the number 78 obviously being what's scaring me). I was wondering if such a temperature is normal and if not what the problem could be. Air flow in my case is phenomenal and besides having to ship back a faulty GPU and reseat my CPU my first build has been a very large success which I am enjoying tremendously. There is literally almost no dust in my case due to it being very new as previously mentioned and my RAM sticks are in the correct slots for dual-channel mode. My cable management is pretty great in my opinion with only cables from my PSU lingering in the bottom of the case. At any given opportunity I ran my cables behind my mobo. Air flow should definitely not be a problem because my CPU only goes up to about 60c and my GPU only goes up to about 80c. Thank you very much in advance.

  Read the article

• Access router set up as a bridge behind another router

  - by Alari Truuts

  I have a problem my ISP is refusing to help me with, even though they put up the whole system. Specifications: There's a Thomson TG784 router through which the internet comes in to the building, Behind that (for some reason) is a Juniper NetScreen 5XT - 105 Firewall/Router? which leads to an AMX nxa-enet24 switch that carries the connections all over the building and a series of Apple AirPorts for wifi. Problem: The first router (Thomson) is required for ipTV (by Elion). The tv or ipTV box has to be connected straight to the Thomson router. My service provider cannot see the Thomson router from their side, but see the Juniper, so we might think the Thomson has been configured as a bridge. I need a way to access the Thomson router and see it's configurations, because currently, when connecting a Samsung tv to that router (with elion app for ipTV viewing) or even a computer, it cannot access the internet and even if it could, it would update the Thomson router software, losing it's configurations which I need to preserve. I'm unable to find out the Thomson routers ip address to connect to it, and when directly conencting with a cat5 cable, it doesn't give me an ip address. Hope someone can show me the correct direction for solving my issue. Thank you all for reading, and I appreciate any help, Alari Truuts

  Read the article

• Split MPEG video from command line?

  - by Tim

  I have a homemade DVD that I'm effectively trying to insert chapters into and rearrange - the original author burned it as one long chapter, and I'd like to rip it into smaller pieces and re-encode it into a new DVD. I ripped the DVD with the following command: mplayer dvd:// -dvd-device /dev/sr2 -dumpstream -dumpfile raw.vob I'm running Gentoo Linux with mplayer version 1.0-rc2_p20090731 (the latest available in Portage). I have a list of times that the chapters are supposed to span (for example 30:11-33:25), so my first thought was to rip the entire DVD and use mpgtx to cut out certain pieces of the file. My issue is that running mpgtx -i on the file reports quite a few timestamp jumps: Time stamps jumped from 59.753789 to 0.001622 at position 1d29800 Time stamps jumped from 204963823030450.343750 to 31.165900 at position 2d4f800 Time stamps jumped from 60.077878 to 0.001622 at position 43cc000 Time stamps jumped from 60.024233 to 0.001622 at position 65c5000 Time stamps jumped from 204963823068631.718750 to 52.549244 at position 7fd1000 I've tried to fix the indexes using: mencoder raw.vob -oac copy -ovc copy -forceidx -o fixed.vob -of mpeg But mpgtx will still report timestamp issues. My immediate question: is there a way to take the ripped movie I have and correct its timestamps so I can cut it with mpgtx? If I can get that one issue out of the way, building the rest of the DVD will be smooth sailing. If it's not possible to fix the timestamps on this file: is there a better way to rip small chunks of the DVD into separate files for recompilation later? I'd very much like this to be done on Linux, and it'd be even better if I could script it somehow (feed in a list of start and end positions, or start times and durations, and get out a series of ripped files). If need be, I also have a Mac OS X machine available, but no Windows. Edit: I wound up finding another solution involving HandBrake and ffmpeg (with help from this question), but the question stands. Edit again: Turns out my other solution didn't quite work - the audio desynchronized by about five seconds, in about half of my cut mpgs - so I'm back to square one. Anyone?

  Read the article

• Can not access SQLServer database

  - by btrey

  I'm trying to convert an Access database to use a SQLServer backend. I've upsized the database and everything works on the server, but I'm unable to access it remotely. I'm running SQLServer Express 2005 on Windows Server 2003. The server is not configured as a domain controller, nor connected to a domain. The computers I'm trying to access the server from are part of a domain, but there are no local domain controllers. I'm at a remote location and the computers are configured and connected to the domain at the home office, then shipped to us. We normally log in with cached credentials and VPN into the home office when we need to access the domain. I can use Remote Desktop Connection to access the 2k3 server which is running SQLServer. If I log into the server with my username, I can bring up the database, access it via the Trusted Connection, and the database works. If I try to run the database locally, however, I get the Server Login dialog box. I can not use a Trusted Connection because my local login is to the home office domain and is not recognized by the SQLServer machine. If I try to use the username/password that is local to the SQLServer, I get a login failed error. I've tried entering the username as "username", "workgroup/username" (where "workgroup" is the name of the workgroup on the SQLServer), "sqlservername/username" and "[email protected]" where "1.2.3.4" is the IP of the SQLServer. In all cases, I get a login failed error. As I said, I can login to the server via Remote Desktop Connection with the same username and password and use the database, so permissions for the username appear to be correct for both a remote connection and for database access. Not sure where to go from here and any assistance would be appreciated.

  Read the article

• Add shortcuts to (Windows + X) context menu

  - by KasiyA

  I want to add services.msc into Win+X context menu in windows 8 (x64). I know similar question is in here but it's not good with using Win+X Editor, because it doesn't add Underlined key for shortcuts that added with that and it's not good without having quickly underlined key. I want do that for maually Context menu folder is: C:\Users\User_Name\AppData\Local\Microsoft\Windows\WinX And hide desktop.ini files is as bellows (in ...\WinX\group2\desktop.ini) [LocalizedFileNames] 1 - Run.lnk=@%SystemRoot%\system32\shell32.dll,-12710 4 - Control Panel.lnk=@%SystemRoot%\system32\shell32.dll,-4161 5 - Task Manager.lnk=@%SystemRoot%\system32\authui.dll,-12139 3 - Windows Explorer.lnk=@%SystemRoot%\system32\shell32.dll,-22067 2 - Search.lnk=@%SystemRoot%\system32\shell32.dll,-30517 I copied sevices.msc shortcut into above path in group2 folder and add this line 6 - Sevices.lnk=@%SystemRoot%\system32\sevices.msc,????? in desktop.ini file. First Question: I don't know If this line 6 - Sevices.lnk=@%SystemRoot%\system32\sevices.msc,-????? that I added is correct or not? Also I don't know what to use instead of -????? Last Question: Why desktop.ini contents is not Sorted. I triyed to manually sort them but when I restart Explorer again it was become out of order.Why?

  Read the article

• Question About mk-table-checksum Results

  - by stevenmusumeche

  Hello, I have 1 master and 2 slaves. I am using MySQL 5.1.42 on all servers. I am attempting to use mk-table-checksum to verify that their data is in sync, but I am getting unexpected results on one of the slaves. First, I generate the checksums on the master like this: mk-table-checksum h=localhost --databases MYDB --tables {$table_list} --replicate=MYDB.mk_checksum --chunk-size=10M My understanding is that this runs the checksum queries on the master which then propagate via normal replication to the slaves. So, no locking is needed because the slaves will be at the same logical point in time when they run the checksum queries on themselves. Is this correct? Next, to verify that the checksums match, I run this on the master: mk-table-checksum --databases MYDB --replicate=IRC.mk_checksum --replicate-check 1 h=localhost,u=maatkit,p=xxxx If there are any differences, I repair the slaves like this: mk-table-sync --execute --verbose --replicate IRC.mk_checksum h=localhost,u=maatkit,p=xxxx After doing all of this, I repaired both slaves with mk-table-sync. However, everytime I run this sequence (after everything has already been repaired), one slave is perfectly in sync but one slave always has a few tables out of sync. I am 99.999% sure that the data on the slaves matches, since I repaired everything and the tables were not even updated on the master between runs of the checksum script. What would cause a few tables to always show out of sync on only one of the slaves? I am stuck. Here is the output: Differences on h=x.x.x.x,p=...,u=maatkit DB TBL CHUNK CNT_DIFF CRC_DIFF BOUNDARIES IRC product 10 0 1 product_id = 147377 AND product_id < 162085 IRC post_order_survey 0 0 1 1=1 IRC mk_heartbeat 0 0 1 1=1 IRC mailing_list 0 0 1 1=1 IRC honey_pot_log 0 0 1 1=1 IRC product 12 0 1 product_id = 176793 AND product_id < 191501 IRC product 18 0 1 product_id = 265041 IRC orders 26 0 1 order_id = 694472 IRC orders_product 6 0 1 op_id = 935375

  Read the article

• How to move my data from my old MacBook Pro to my new one?

  - by Tim Büthe

  I just purchased a new MacBook Pro and already got an 2008 model. I wonder how I move all my data over to the new one. My first idea was, to use my Time Machine backup and restore from it, which seems to be a good idea and should work just fine regarding to this link: http://blog.duncandavidson.com/2008/01/restoring-from-time-machine.html. But, since my current MacBook got older Software on it, like iLife '08 instead of iLife '09 I would have to upgrade this afterwards. Is this correct, or does Time Machine does some magic to exclude well known software? And is it possible to reinstall or upgrade iLife with the included installation DVDs? My second idea is, to just swap the hard drives instead of using the Time machine backup. If it is not too complicated to remove the hdd, this should be the fastest way. This also has the benefit, that the 2008er MacBook then contains a brand new installation and I don't have to remove all my stuff or reinstall Mac OS before I give it away. My question on that second idea would be: does snow leopard handle this stuff correctly? I reboot with the new hardware and all just works fine? So in a nutshell: What would you do: restore from backup or swap drives? And what about the new software?

  Read the article

• Postfix with relayhost - relay access denied for bounces

  - by Alex

  I have set up a Postfix Mailserver, outgoing mail is being sent through a smarthost/relayhost which requires authentification. That works great, internal clients can send to foreign recipients though this relayhost. However, when an external mail for a local, non-existent user arrives at the server, postfix tries to send a non-delivery notification to the sender. This mail is also sent through the relayhost obviously, but it fails with error 554 5.7.1 : Relay access denied This gets logged to the mail.log: Nov 9 10:26:42 mail postfix/local[5051]: 6568CC1383: to=<[email protected]>, relay=local, delay=0.13, delays=0.02/0.02/0/0.09, dsn=5.1.1, status=bounced (unknown user: "test") Nov 9 10:26:42 mail postfix/cleanup[5045]: 85DF9BFECD: message-id=<[email protected]> Nov 9 10:26:42 mail postfix/qmgr[4912]: 85DF9BFECD: from=<>, size=3066, nrcpt=1 (queue active) Nov 9 10:26:42 mail postfix/bounce[5052]: 6568CC1383: sender non-delivery notification: 85DF9BFECD Nov 9 10:26:42 mail postfix/qmgr[4912]: 6568CC1383: removed Nov 9 10:26:43 mail postfix/smtp[5053]: 85DF9BFECD: to=<[email protected]>, relay=mail.provider.com[168.84.25.111]:587, delay=0.48, delays=0.02/0.01/0.26/0.18, dsn=5.7.1, status=bounced (host mail.provider.com[168.84.25.111] said: 554 5.7.1 <[email protected]>: Relay access denied (in reply to RCPT TO command)) Nov 9 10:26:43 mail postfix/qmgr[4912]: 85DF9BFECD: removed According to this error, I suppose that postfix does not login at the relayhost when sending those bounces. Why? Normal outgoing mail works just fine. This is how my main.cf looks like: http://pastebin.com/Uu1Dryxy And of course /etc/postfix/sasl_password contains the correct credentials for the relayhost. Thanks in advance!

  Read the article

• cannot connect to <server_name>\sqlexpress

  - by Jackson Sunuwar

  I have tried disabling firing wall and checked sqlbrowser is started but for some reason I cannnot connect to my datbase... called server_name\sqlexpress.. I have a virtual machine and a full scale MS SQL Server 2008 R2 running on it... and I have several other vm running sqlexpress. they run fine and I can connect to them using sqlexpress... but when i try to access from sqlserver... I get this error. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) Digging deep into the error, I found this Error Number: -1 Severity: 20 State: 0 and finally this... Program Location: at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server) at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser() Firewall is turned off on the VM that's running mssqlserver... I turned of firewall on one of the vm that's running the sqlexpress but I still get the error... can someone please help... thank you

  Read the article

• Secretary cannot add appointments to boss's calendar after exchange restore from backup

  - by therulebookman

  The calendar is the Boss's calendar on Exchange. I have set permissions for it through his Outlook to give the secretary and a few other people "Editor" access to his calendar. All the editors can view the calendar, but only he can add new appointments. Anyone else who tries to add an appointment gets "The item cannot be saved in this folder. The folder was deleted or moved or you do not have permission." The permissions are correct, editor. The item hasn't been deleted or moved. It's in his mailbox on exchange. The message says something about the mailbox size, but he is well under the size limit anyway. He is using Outlook 2003, and I have tried accessing it from 2003 and 2007, but I don't think that is related I tried clearing the forms cache and enabling disabled items: no disabled items and clearing cache didn't help. I also tried "Allow all forms" but this apparently doesn't apply in this scenario as we are not using any custom forms. Is there any way to delete just his calendar and then I can exmerge it back in (after exporting to PST of course)? I really can't exmerge out his mailbox, delete it, and exmerge it back in because he works all sorts of hours, but if this is the only way, then I'll have to do it. Is there any other possible solution?

  Read the article

• Specify default group and permissions for new files in a certain directory

  - by mislav

  I have a certain directory in which there is a project shared by multiple users. These users use SSH to gain access to this directory and modify/create files. This project should only be writeable to a certain group of users: lets call it "mygroup". During an SSH session, all files/directories created by the current user should by default be owned by group "mygroup" and have group-writeable permissions. I can solve the permissions problem with umask: $ cd project $ umask 002 $ touch test.txt File "test.txt" is now group-writeable, but still belongs to my default group ("mislav", same as my username) and not to "mygroup". I can chgrp recursively to set the desired group, but I wanted to know is there a way to set some group implicitly like umask changes default permissions during a session. This specific directory is a shared git repo with a working copy and I want git checkout and git reset operations to set the correct mask and group for new files created in the working copy. The OS is Ubuntu Linux. Update: a colleague suggests I should look into getfacl/setfacl of POSIX ACL but the solution below combined with umask 002 in the current session is good enough for me and is much more simple.

  Read the article

• Backing up Excel Files to a different Directory

  - by Joe Taylor

  In Excel 2007 in the Save As box there is an option to 'Create a Backup' which simply backs up the file whenever it is saved. Unfortunately it backs up the file to the same directory as the original. Is there a simple way to change this directory to another drive / folder? I have messed about with macros to do this, coming up with: Private Sub Workbook_BeforeClose(Cancel As Boolean) 'Private Sub Workbook_BeforeSave(ByVal SaveAsUI As Boolean, Cancel As Boolean) 'Saves the current file to a backup folder and the default folder 'Note that any backup is overwritten Application.DisplayAlerts = False ActiveWorkbook.SaveCopyAs Filename:="T:\TEC_SERV\Backup file folder - DO NOT DELETE\" & _ ActiveWorkbook.Name ActiveWorkbook.Save Application.DisplayAlerts = True End Sub This creates a backup of the file ok the first time, however if this is tried again I get: Run-Time Error '1004'; Microsoft Office Excel cannot access the file 'T:\TEC_SERV\Backup file folder - DO NOT DELETE\Test Macro Sheet.xlsm. There are several possible reasons: The file name or path does not exist The file is being used by another program The workbook you are trying to save has the same name as a... I know the path is correct, I also know that the file is not open anywhere else. The workbook has the same name as the one I'm trying to save over but it should just overwrite. I have posted the question about the coding on Stack Overflow but wondered if there is an easier way to do this. Any help would be much appreciated. Joe

  Read the article

• Secure openVPN using IPTABLES

  - by bob franklin smith harriet

  Hey, I setup an openVPN server and it works ok. The next step is to secure it, I opted to use IPTABLES to only allow certain connections through but so far it is not working. I want to enable access to the network behind my openVPN server, and allow other services (web access), when iptables is disabaled or set to allow all this works fine, when using my following rules it does not. also note, I already configured openVPN itself to do what i want and it works fine, its only failing when iptables is started. Any help to tell me why this isnt working will appreciated here. These are the lines that I added in accordance with openVPN's recommendations, unfortunately testing these commands shows that they are requiered, they seem incredibly insecure though, any way to get around using them? # Allow TUN interface connections to OpenVPN server -A INPUT -i tun+ -j ACCEPT #allow TUN interface connections to be forwarded through other interfaces -A FORWARD -i tun+ -j ACCEPT # Allow TAP interface connections to OpenVPN server -A INPUT -i tap+ -j ACCEPT # Allow TAP interface connections to be forwarded through other interfaces -A FORWARD -i tap+ -j ACCEPT These are the new chains and commands i added to restrict access as much as possible unfortunately with these enabled, all that happens is the openVPN connection establishes fine, and then there is no access to the rest of the network behind the openVPN server note I am configuring the main iptables file and I am paranoid so all ports and ip addresses are altered, and -N etc appears before this so ignore that they dont appear. and i added some explanations of what i 'intended' these rules to do, so you dont waste time figuring out where i went wrong : 4 #accepts the vpn over port 1192 -A INPUT -p udp -m udp --dport 1192 -j ACCEPT -A INPUT -j INPUT-FIREWALL -A OUTPUT -j ACCEPT #packets that are to be forwarded from 10.10.1.0 network (all open vpn clients) to the internal network (192.168.5.0) jump to [sic]foward-firewall chain -A FORWARD -s 10.10.1.0/24 -d 192.168.5.0/24 -j FOWARD-FIREWALL #same as above, except for a different internal network -A FORWARD -s 10.10.1.0/24 -d 10.100.5.0/24 -j FOWARD-FIREWALL # reject any not from either of those two ranges -A FORWARD -j REJECT -A INPUT-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT-FIREWALL -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT-FIREWALL -j REJECT -A FOWARD-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT #80 443 and 53 are accepted -A FOWARD-FIREWALL -m tcp -p tcp --dport 80 -j ACCEPT -A FOWARD-FIREWALL -m tcp -p tcp --dport 443 -j ACCEPT #192.168.5.150 = openVPN sever -A FOWARD-FIREWALL -m tcp -p tcp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -m udp -p udp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -j REJECT COMMIT now I wait :D

  Read the article

• Why is it necessary to chmod o+r parent directory to fix 403 access forbidden error with Nginx and P

  - by davenolan

  This may be an Nginx wrinkle, or it may be because I don't understand Unix permissions. We're using Hudson CI to deploy our staging instance. So RAILS_ROOT is /var/lib/hudson/jobs/JOBNAME/workspace. Hudson runs as hudson user Nginx runs as www-data user hudson and nginx are both members of the www group root of my nginx conf points to RAILS_ROOT/public as per normal. RAILS_ROOT/config/environment.rb is owned by www-data (so Passenger runs as www-data) RAILS_ROOT and everything in it is owned by the www group and group has r/w/x permissions As it stood, Nginx threw 403 permission denied when requesting any url. error.log contained entries like this: public/index.html" is forbidden (13: Permission denied). These did not fix the or change the error (each with a stop/start of Ngnix): chmod 777 -R RAILS_ROOT chgrp www -R /var/lib/hudson I also tried Nginx as root, and passenger complained that it could not find config/environment (despite the path displayed on the error page being correct). The fix was to ensure everybody has read permissions on each directory in the heirachy. In this case chmod o+r /var/lib/hudson. But if the group has read permissions on the directory, and nginx is a member of the owner group of the directory, why was it necessary to allow everyone read permissions? Is there something have not grokked about permissions? $nginx -V nginx version: nginx/0.7.61 built by gcc 4.4.1 (Ubuntu 4.4.1-4ubuntu8) configure arguments: --prefix=/opt/nginx --add-module=/usr/lib/ruby/gems/1.8/gems/passenger-2.2.5/ext/nginx --with-http_ssl_module --with-pcre=~/src/pcre-8.00/ --with-http_stub_status_module $cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=9.10 DISTRIB_CODENAME=karmic DISTRIB_DESCRIPTION="Ubuntu 9.10"

  Read the article

• Mail.app doesn't detect sender in Address Book

  - by CoreSandello

  I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

  Read the article

• FTP not listing files behind firewall (setsockopt (ignored): Permission denied)

  - by KennyDs

  We are developing a Magento application that has a module that works with FTP. Today we deployed this on the testing environment which is setup in the following way: Gateway server which has the following iptables rules: # iptables -L -n -v Chain INPUT (policy ACCEPT 2 packets, 130 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 165 13720 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED Chain FORWARD (policy ACCEPT 7 packets, 606 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- eth1 eth0 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 15 965 ACCEPT all -- eth0 eth1 0.0.0.0/0 0.0.0.0/0 0 0 REJECT all -- eth1 eth1 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 126 packets, 31690 bytes) pkts bytes target prot opt in out source destination These are set at runtime via the following bash script: #!/bin/sh PATH=/usr/sbin:/sbin:/bin:/usr/bin # # delete all existing rules. # iptables -F iptables -t nat -F iptables -t mangle -F iptables -X # Always accept loopback traffic iptables -A INPUT -i lo -j ACCEPT # Allow established connections, and those not coming from the outside iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the LAN side. iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT # Masquerade. iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE # Don't forward from the outside to the inside. iptables -A FORWARD -i eth1 -o eth1 -j REJECT # Enable routing. echo 1 > /proc/sys/net/ipv4/ip_forward The gateway server is connected to the WAN via eth1 and is connected to the internal network via eth0. One of the servers from eth1 has the following problem when trying to list files over ftp: $ ftp -vd myftpserver.com Connected to myftpserver.com 220 Welcome to MY FTP Server ftp: setsockopt: Bad file descriptor Name (myftpserver.com:magento): XXXXXXXX ---> USER XXXXXXXX 331 User XXXXXXXX, password please Password: ---> PASS XXXX 230 Password Ok, User logged in ---> SYST 215 UNIX Type: L8 Remote system type is UNIX. Using binary mode to transfer files. ftp> ls ftp: setsockopt (ignored): Permission denied ---> PORT 192,168,19,15,135,75 421 Service not available, remote server has closed connection When I try listing the files in passive mode, same result. When I run the same command on the gateway server, everything works fine so I believe that the issue is happening because of the iptables rules not forwarding properly. Does anyone have an idea which rule I need to add to make this work?

  Read the article

• How to force Debian to boot new Kernel?

  - by ThE_-_BliZZarD

  I'm running Debian 6, Debian GNU/Linux, with Linux 2.6.32-5-amd64 under Grub2 ( 1.98+20100804-14+squeeze1) on a remote system (no possibility to view the pre-boot messages). I compiled and installed a new kernel, but I can not get it to boot. What I have done: Installed the packages via: dpkg -i linux-headers-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb linux-image-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb This updated the Grub configuration. My /boot/grub/grub.cfg now contains: menuentry 'Debian GNU/Linux, with Linux 3.5.3.20120914-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 3.5.3.20120914-amd64 ...' linux /vmlinuz-3.5.3.20120914-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-3.5.3.20120914-amd64 } menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 2.6.32-5-amd64 ...' linux /vmlinuz-2.6.32-5-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-2.6.32-5-amd64 } I used grub-set-default "Debian GNU/Linux, with Linux 2.6.32-5-amd64" to set the old kernel as default and then grub-reboot "Debian GNU/Linux, with Linux 3.5.3.20120914-amd64" to boot into the new kernel once. After update-grub I rebooted the system, but everytime it comes back up with the old kernel (2.6). I tried setting the new one as default (grub-set-default 0, update-grub, reboot) but, still the old one. The Syslogs contain NO hint whatsoever about trying to boot the new kernel - only the old one. Would there be any hints regarding problems with a kernel? Is there a way to enable debug-logging in grub? What am I doing wrong? How can I force the system to boot the new kernel? Edit: Hardware of remote machine. CPU cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 5 model name : AMD Athlon(tm) II X4 605e Processor stepping : 3 cpu MHz : 2294.898 cache size : 512 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt bogomips : 4589.77 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate (copied only the first, 3 more follow) The server is a Fujitsu PRIMERGY MX130 S1.

  Read the article

• Real benefits of tcp TIME-WAIT and implications in production environment

  - by user64204

  SOME THEORY I've been doing some reading on tcp TIME-WAIT (here and there) and what I read is that it's a value set to 2 x MSL (maximum segment life) which keeps a connection in the "connection table" for a while to guarantee that, "before your allowed to create a connection with the same tuple, all the packets belonging to previous incarnations of that tuple will be dead". Since segments received (apart from SYN under specific circumstances) while a connection is either in TIME-WAIT or no longer existing would be discarded, why not close the connection right away? Q1: Is it because there is less processing involved in dealing with segments from old connections and less processing to create a new connection on the same tuple when in TIME-WAIT (i.e. are there performance benefits)? If the above explanation doesn't stand, the only reason I see the TIME-WAIT being useful would be if a client sends a SYN for a connection before it sends remaining segments for an old connection on the same tuple in which case the receiver would re-open the connection but then get bad segments and and would have to terminate it. Q2: Is this analysis correct? Q3: Are there other benefits to using TIME-WAIT? SOME PRACTICE I've been looking at the munin graphs on a production server that I administrate. Here is one: As you can see there are more connections in TIME-WAIT than ESTABLISHED, around twice as many most of the time, on some occasions four times as many. Q4: Does this have an impact on performance? Q5: If so, is it wise/recommended to reduce the TIME-WAIT value (and what to)? Q6: Is this ratio of TIME-WAIT / ESTABLISHED connections normal? Could this be related to malicious connection attempts?

  Read the article

• How do I delete hardlinks, symbolic links, junction points, etc please?

  - by jonny

  I could be wrong, but I'm yet to hear a valid argument for the exploitability that these things deliver...outweighing their very dubious / debatable functionality. They seem to me to be marginally handy, but I don't think I have any need for them. I do have a need for security, however. How can I delete their entire functionality permanently from my hard drive, please? Microsoft only has pages on how to create them; which seems almost peculiar to the point of being dubious (at least, to me...) And just a dumb command line question, am I correct in assuming fsutil hardlink list c: will enumerate every single hardlink on that drive? C:\Windows\system32>fsutil hardlink list c: \Windows\System32 Also, how do I delete symbolic links please ;) But I'd just rather have all symbolic linking and recursion-creating stuff removed, if that's possible? C:\Windows\system32>fsutil behavior query symlinkevaluation Local to local symbolic links are enabled. Local to remote symbolic links are enabled. Remote to local symbolic links are disabled. Remote to remote symbolic links are disabled.

  Read the article

• Xorg input devices fail without udev

  - by Sampo

  What I am trying to do: Launch Xorg server without udev device manager. What I have tried to do: Make sure that /dev/ has all required nodes, such as /dev/input/*. Make sure that all required kernel modules are loaded. Launch Xorg. What happens: Xorg starts up as excepted. Xorg loads correct GPU driver and sets right screen resolution. Xorg blocks all input devices (keyboard, mouse), Alt+F[1-12] does not work (can't go back to tty1). Unraw'ing keyboard to take its control from X removes blocking and after unraw I can Alt+F1 back to tty1. Xorg still does not handle any input. Why I think that it should work: Same configuration works well if udev is loaded. Loading udev does not add or modify /dev/ contents, all nodes stays same. My main question is: How to make Xorg input devices work without udev? Any additional information about how Xorg really uses/detects/grabs keyboard would be helpful. And any additional information about what udev really does (other than populating /dev/) would also be helpful.

  Read the article

< Previous Page | 770 771 772 773 774 775 776 777 778 779 780 781  | Next Page >