Search Results

Search found 26977 results on 1080 pages for 'input device'.

Page 778/1080 | < Previous Page | 774 775 776 777 778 779 780 781 782 783 784 785  | Next Page >

• No headphone or speakers plugged in - Windows 7 issue

  - by Amit Ranjan

  I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

  Read the article

• Load balanced IIS. Should I use NLB, or linux-based reverse proxy, or something else?

  - by growse

  What would be the best approach for load-balancing at least 2-3 Windows 2008 R2 IIS webservers running a multitude of .NET applications? My choices appear to be: 1) Hardware-based network device load balancer, like a Cisco CSS 2) Windows NLB 3) Some sort of linux based proxy, either haproxy or other The three servers sit as VMs on a vSphere farm, so I have the ability to clone to up the instance count in times of high load. I control the switch that the vSphere hosts are plugged into (Cisco 3750), but don't control the switching/routing infrastructure beyond that to the clients. (1) Is too expensive, and probably overkill for my needs. I've included this in case someone figures out a cunning way to do it on my existing network kit, which I doubt. (2) would seem to be the obvious "built-in" option, but seems to be quite fiddly messing around with network interfaces, multicast, and generally other things that seem to be needlessly complex. It's also fairly stupid, in that it can't remove hosts from the pool if they start throwing 500 errors or otherwise go wrong (3) is the most interesting option, as it would appear to offer the most flexibility and customizability, but without having to mess around with the network. However, while I'm familiar with the reverse-proxy capabilities of lighttpd etc, I'm not that well read on other options like HAProxy, which might be able to offer a lot more. Which would you go for, and is there anything I've not thought of?

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

• How to disable "safely remove hardware"

  - by Matt

  I have some windows 7 virtual machines in xen that have devices showing up in "safely remove hardware". I don't want users to ever be able to remove/eject any hardware at all. I'm told vmware has a hotplug option. xen doesn't seem to provide this for pci passthrough devices, therefore I'm looking for a reliable solution to prevent users from ejecting devices. This issue is not necessarily related just to virtual machines but seems to be a common problem with devices that get wrongly reported as removable. I'm ideally looking for a way to prevent all devices from appearing or just prevent the safely remove hardware option from ever coming up. I've tried setting device capabilities for specific devices on boot with a script but this for some reason doesn't always seem to work reliably. Is there a way to prevent this icon from appearing in the notification area completely, either by registry key or group policy? I should point out that setting this in group policy to "Administrators" did not seem to work. [Computer ConfigurationWindows SettingsSecurity SettingsLocal PoliciesSecurity Optionsevices:Allowed to format and eject removable media]

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Can I get ethernet out of my Verizon FIOS set-top box?

  - by Tom Hughes

  Setup: my home network is long & skinny, and the FIOS-connected router is all the way at one of the apartment. At the other end, far away (and a floor higher) is my HD TV, which gets a cable-TV signal from a Verizon set-top box that is coax-connected back to the FIOS on-premises equipment. Wi-Fi won't work, the apartment is too stretched out, with old, thick walls and floors. Goal: I think there are three ways to get ethernet back to where the HD TV is: 1) run a cable! this isn't crazy but isn't cheap either (my building won't let me do it, it involves hiring an electrician because the cable would run partly through the public hallway ceiling) 2) split the coax near the TV and put in... a MoCA device? 3) somehow tease the set-top box, which has an RJ-11 (ethernet) port on the back, to give me network access. Question: any other choices? and, is one choice better than the others? #3 is by far the most desirable because it would involve the least wiring -- but I can't find any resources to help make it happen. #2 is a bit scary, I don't want to degrade service to the TV or anywhere else for that matter.

  Read the article

• Linux commands shows different results

  - by ClydeFrog

  I'm really having a hard time to process these results on my Ubuntu server. I have a major problem with my JBoss server where I get FileNotFoundExceptions along with "No space left on device" errors. And I thought "maybe I'm out of disk space", and used df command to figure out how much I have left: root@ubuntu1:/# df -h Filsystem Storlek Anvnt Tillg Anv% Monterat på /dev/mapper/ubuntu1-root 36G 13G 21G 38% / none 2,0G 192K 2,0G 1% /dev none 2,0G 0 2,0G 0% /dev/shm none 2,0G 64K 2,0G 1% /var/run none 2,0G 0 2,0G 0% /var/lock /dev/sda1 228M 23M 193M 11% /boot /dev/mapper/vgdata-lvdata 79G 9,2G 66G 13% /data And as you can see, I have plenty of space left. And I also checked if I'm out of i-nodes: root@ubuntu1:/# df -i Filsystem Inoder IAnv IFria IAnv% Monterat på /dev/mapper/ubuntu1-root 2346512 61992 2284520 3% / none 505380 773 504607 1% /dev none 507383 1 507382 1% /dev/shm none 507383 30 507353 1% /var/run none 507383 2 507381 1% /var/lock /dev/sda1 124496 230 124266 1% /boot /dev/mapper/vgdata-lvdata 10486784 233945 10252839 3% /data But then i used du: root@ubuntu1:/# du -s -h /* 7,5M /bin 23M /boot 19G /data 192K /dev 11G /eniro 5,3M /etc 112K /home 0 /initrd.img 183M /lib 0 /lib64 16K /lost+found 12K /media 4,0K /mnt 4,0K /opt du: kan inte komma åt "/proc/20452/task/20452/fd/3": Filen eller katalogen finns inte du: kan inte komma åt "/proc/20452/task/20452/fdinfo/3": Filen eller katalogen finns inte du: kan inte komma åt "/proc/20452/fd/3": Filen eller katalogen finns inte du: kan inte komma åt "/proc/20452/fdinfo/3": Filen eller katalogen finns inte 0 /proc 18M /root 8,2M /sbin 4,0K /selinux 8,0K /srv 0 /sys 40K /tmp 691M /usr 1,2G /var 0 /vmlinuz Notice that /data and /eniro are 30G combined! How is it possible? Do I have a memory leak somewhere? Or is it something else? ----- EDIT 1 ----- Ok, I figured out that /data has its own mount so it's not possible to combine /data and /eniro because they aren't on the same mount. But how come it says 9,2G on the first command when it says 19G on the third on directory /data?

  Read the article

• Is current SATA 6 gb/s equipment simply unreliable?

  - by korkman

  I have a 45-disk array of Seagate Barracuda 3 TB ST3000DM001 (yes these are desktop drives I'm aware of that) in a Supermicro sc847 JBOD, connected via LSI 9285. I have found a solution for the problem description below by reducing speed via MegaCli -PhySetLinkSpeed -phy0 2 -a0; for i in $(seq 48); do MegaCli -PhySetLinkSpeed -phy${i} 2 -a0; done and rebooting. The question remains: Is this typical for current 6 gb/s equipment? Is this the sad state of SATA storage? Or is some of my equipment (the sff-8088 cables come to mind) bad? The Problem was: Synchronizing HW RAID-6, disks kept offlining. Fetching SMART values reveiled that those which offlined did not increase powered-on hours anymore. That is, their firmware (CC4C) seems to crash. Digging into the matter by switching to Software RAID-6, with the disks passed-through, I got tons of kernel messages scattered across all disks, with 6 gb/s: sd 0:0:9:0: [sdb] Sense Key : No Sense [current] Info fld=0x0 sd 0:0:9:0: [sdb] Add. Sense: No additional sense information And finally, when a disk offlines: megasas: [ 5]waiting for 160 commands to complete ... megasas: [35]waiting for 159 commands to complete ... megasas: [155]waiting for 156 commands to complete ... megaraid_sas: pending commands remain after waiting, will reset adapter. Ugly controller reset here, then minutes later: megaraid_sas: Reset successful. sd 0:0:28:0: Device offlined - not ready after error recovery ... sd 0:0:28:0: [sdu] Unhandled error code sd 0:0:28:0: [sdu] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK sd 0:0:28:0: [sdu] CDB: Read(10): 28 00 23 21 2f 40 00 00 70 00 sd 0:0:28:0: [sdu] killing request Reduced speed to 3 gb/s like written above, all problems vanished.

  Read the article

• "Safe" personal router use on apartment-wide network

  - by noisetank

  I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

  Read the article

• Finding a shared HDD attached to the network from my F-13 machine

  - by Ramy

  Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

  Read the article

• Eee PC Seashell series netbook screen is cut off at bottom no matter the resolution

  - by Yzmir Ramirez

  I have an Eee PC 1015PE Seashell netbook running Windows 7 Home Premium with an Intel Graphics Media Accelerator 3150 (8.14.10.2230) with a "Generic Non-PnP Monitor" detected. I tried: Changing the resolution (Control Panel = Appearance and Personalization = Display = Screen Resolution) to 1024x768 Updating the video driver (to 8.14.10.2230) Uninstalling the driver and rebooting Pressing the Windows Key + "-" (magnifier) Pressing Ctrl + Mouse Scroll only resizes the desktop items Pressing Fn + F4 shows 1024x600 (which I think is what I should be using, but nothing happens) EDIT: Changed from Landscape to Portrait and it works Attached an External Monitor and when I extend or set as desktop it works only on the External Monitor (shows up as "Generic PnP Monitor in Device Manager) Basically the bottom inch of my desktop is off-screen hiding my start bar, but my wigets are in their proper position (the start bar is not hidden). Pressing Ctrl + Esc shows the start menu but its cut-off. I'm pretty sure I should be using 1024x600 resolution, any advice? What's odd is that this only started happening recently. EDIT2: Here are some screenshots showing the problem: Resized Window to fit: Opened Start Menu - notice it cut off: Maximized window and then scrolled down - notice no Start Menu: I downgraded my graphic driver I downloaded from the Intel Download Center for the Graphic Media Accelerator 3150 (now: 8.14.10.1972) and now my "Generic non-PnP Montior" detects as "Digital Flat Panel (1024x768 60Hz)".

  Read the article

• Wireless driver activation problem in compaq c700 in ubuntu 9.04

  - by Fazil

  I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

  Read the article

• Reliable applicance for routing IT emergency calls (SIP and ISDN)

  - by chiborg

  We have a fairly big IT installation and our IT staff needs to be reachable 24/7. At the moment we have the following setup for "emergency" calls to our IT staff on our main Asterisk box: An incoming emergency number (connected via SIP trunk and a BRI card in case the SIP trunk goes down). When the number is called during the office hours, all the SIP phones of the IT staff are called simultaneously. When the number is called out of office hours interface, a list of mobile phone numbers is called, one after another until someone picks up. The list can be changed by the IT staff via command line script. The setup works well, but the Asterisk is heavily used in a call center, has experienced some outages and misconfigurations, each of them bringing down the IT emergency number. So we'd like to put the IT emergency call functionality on a separate device. This does not need to be a big server, it even does not need to be Asterisk, it only has one purpose and should do it reliably. It should be very low-maintenance. Any suggestions for hard- and software?

  Read the article

• USB 3.0 hard disk not detected on a particular host controller?

  - by Alvin Wong

  I have a USB 3.0 hard disk which has always been working on my desktop with an XHCI. Now I just bought a notebook with an XHCI (something with Intel's Ivy Bridge setup). The first time I plug the hard disk in its 3.0 port it is detected and working. A few hours later I try to connect it again, but seems that the notebook just ignored it! The light on the hard disk didn't blink as usual (instead it is hold at on). I then tested it with my desktop again and it is working perfectly. It gets trickier when I plug it in the USB 2.0 port of that notebook it is detected and working perfectly (despite the slower speed). Then I try to plug in an USB 2.0 USB flash drive to that USB 3.0 port, and it is detected (of course as USB 2.0). So, there are two USB 3.0 ports on my notebook's XHCI. Both of them are not working with my hard disk but working perfectly fine with my USB 2.0 UFD. What's wrong with it? When I plug in the hard disk, device manager doesn't change. I've tried re-installing the driver for the XHCI, but it changes nothing. Had I broke the USB 3.0-specific pins of both USB 3.0 ports?

  Read the article

• Expand disk space on Ubuntu 10.04 (VMWare Guest)

  - by Jason Clawson

  I need to resize the disk space of an ubuntu guest in VMWare Workstation. After using the expand disk utility in vmware workstation, I need to do some linux magic to resize the parition. I have searched and found a lot of posts about resizing it. Unfortunately I don't really understand it all that well. Can anyone help me out with this? df -h gives me: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 19G 2.6G 16G 15% / none 496M 172K 495M 1% /dev none 500M 0 500M 0% /dev/shm none 500M 64K 500M 1% /var/run none 500M 0 500M 0% /var/lock none 500M 0 500M 0% /lib/init/rw none 19G 2.6G 16G 15% /var/lib/ureadahead/debugfs /dev/sda1 228M 36M 181M 17% /boot lvs says: LV VG Attr LSize Origin Snap% Move Log Copy% Convert root ubuntu -wi-ao 18.88g swap_1 ubuntu -wi-ao 884.00m fdisk -l says: Disk /dev/sda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00033718 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 2611 20719617 5 Extended /dev/sda5 32 2611 20719616 8e Linux LVM I really appreciate the help.

  Read the article

• How to reinstall Windows Boot Manager on EFI partition

  - by joaocandre

  So I've been trying to install Ubuntu on a second HDD on my desktop, which has W8 installed on a SSD (UEFI-only boot). Thing is, during Ubuntu installation I made the mistake of choosing to install the bootloader (GRUB) to the first disk (the SSD), and after install I could not boot into W8 (the entries in GRUB didn't work). Following these instructions, I managed to be able to get "Windows Boot Manager" back, however I lost GRUB in the process, and got a duplicate "Windows Boot Manager" entry in BIOS, along with the "Ubuntu" entry, which then I used to boot into Ubuntu. Later, I decided to reinstall Ubuntu, and formatted the HDD from within windows, however, the entries in BIOS stayed the same, and, while I had the HDD connected to the motherboard, I could not boot into an Ubuntu Live USB (in order to reinstall Ubuntu). I made another mistake by updating the BIOS, which cleared all of the EFI boot entries in BIOS, and, right now, I get an error when boot from the SSD: grub: device not found (...) So it seems that grub is still installed in the EFI partition of the SSD, and since I don't have the WBM entry in BIOS anymore, I cannot even boot into Windows, and the previous instructions don't work anymore. Is there another way to reset W8 EFI partition to the default?

  Read the article

• Possible to host CentOS netinstall files on a local HTTP/FTP?

  - by garlicman

  I'm running XenServer on an Dell R610 and am running into a catch-22. During install from DVD, CentOS can't find the DVD package catalogue. It's a reported error for some, XenServer + CentOS6 + DVD install in some hardware configurations = failed install. Yes, I checked the MD5 and let the disc test pass. In every reported case, the netinstall was the solution. The issue is my net access is required to go through a web proxy that prompts before you can download a file. This naturally breaks any download automation. I've been waiting on our IT to put in an exception rule to allow my lab to bypass the prompt, but it's been over 3 weeks now and they don't seem responsive. (I've been working on this a day or two a week) I want to try and host the netinstall files local in my Xen network. Right now I only have a bunch of Windows based VMs, CentOS won't install so I don't have any Linux tools. I had tried simply hosting all the DVD contents off one of the Windows servers using Mongoose. (I didn't want to setup IIS) I copied them to a hosted sub-directory similar to all the mirrors out there (e.g. http:///centos/6.2/os/i386/) with no auth or anything. Then in the netinstall I correctly pointed to it. I now realize just copying the DVD files over won't work. The repodata will point to a local device, not the site I'm hosting. (e.g. the DVD repodata includes xml that points to where the packages are) Clearly I'm hosting them over HTTP, not from a DVD. Is there an easy way to sort this out? I'm just trying to install CentOS6 on Xen. If there's a turnkey downloadable Xen image with CentOS 6.2 on it, or a downloadable repo image, I'll take that too! Thank you in advance!

  Read the article

• Microsoft SQL Server Management Studio causing system freeze

  - by CRoshanLG

  I'm experiencing very slow response from MSSMS and it causes other applications to slow down. Specially Skype crashes after few seconds from opening MSSMS, showing an error called "Disk I/O Error". I'm regularly using few applications (Sublime text, MS Word, Firefox, Outlook, Skype and one or two other apps) simultaneously. The system works fine when MSSMS is not in use! But as soon as MSSMS is opened, all the apps start to freeze (MSSMS also responds very slow). This problem has been there for about a week now (I haven't installed any apps or haven't made any changes to the system during that time). -- System Specifications -- Processor: Core i3 (3.1 GHz) RAM: 4 GB OS: Windows 7 Professional (64 bit) Free space in C drive: ~ 100 GB MS SQL Server 2008 R2 Microsoft SQL Server Management Studio version - 10.50.1600.1 I've tried to find a reason for this but there are no helpful information in the web! There are some solutions suggested (in forums and in Skype Support pages) for the Skypes' "Disk I/O Error", all of which I tried but does not solve the problem. Has anyone faced the same senario? (and hopefully) knows a solution? Systems Log I don't have much knowledge in interpreting the System Log, but I think the Critical and Warnings are not helpful. But there are lots of Error logs which might be useful. In source Kernal-General there are few similar errors saying "An I/O operation initiated by the Registry failed unrecoverably.The Registry could not flush hive (file): <some file>" In source atapi also there are few similar errors -- "The driver detected a controller error on \Device\Ide\IdePort0." (all errors has occurred in 'IdePort0') In Application Error, there are several errors logged, and following is the latest one. Both the Errors which has occurred today is similar (to this one). As it is from Ssms.exe, I guess this is relevant to the cause of problem. But as I said above I can't understand what it means!

  Read the article

• Debian - starting UFW (Uncomplicated Firewall) before network interfaces are operational

  - by Tomasz Zielinski

  I want to install UFW on Debian Lenny. Everything looks straightforward except that I don't know where to plug UFW startup script so that it configures iptables before hax0rs can break in. I've reviewed runlevel directories and in /etc/rc0.d, /etc/rc6.d and /etc/rcS.d there are items like these: S35networking -> ../init.d/networking S36ifupdown -> ../init.d/ifupdown Runlevel 0 and 6 are for shutdown and reboot so I guess nothing should be changed there, but runlevel S advertises itself (in README) like something for me: The scripts in this directory whose names begin with an 'S' are executed once when booting the system, even when booting directly into single user mode. The following sequence points are defined at this time: * After the S40 scripts have executed, all local file systems are mounted and networking is available. All device drivers have been initialized. (What bothers me is that both rc0/6.d and rcS.d point to the same networking and ifupdown scripts, but after looking at sources I believe those scripts are smart enough to figure out where to start and where to stop networking.) Now, I think that I should plug my /lib/ufw/ufw-init into /etc/rcS.d, with priority higher that the one of ifupdown and networking, i.e. <= 38 for my /etc/rcS.d. Am I right in this "analysis" ?

  Read the article

• Tidy up old Windows Server Backup snapshots

  - by dty

  Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

  Read the article

• recursive grep started at / hangs

  - by Martin

  I have used following grep search pattern on multiple platforms: grep -r -I -D skip 'string_to_match' / For example on FreeBSD 8.0, FreeBSD 6.4 and Debian 6.0(squeeze). Command does a recursive search starting from root directory, assumes that binary files do not have the 'string_to_match' and skips devices, sockets and named pipes. FreeBSD 8.0 and FreeBSD 6.4 use GNU grep version 2.5.1 and Debian 6.0 uses GNU grep version 2.6.3. On FreeBSD 6.4, last information printed to stderr was "grep: /dev/cuad0: Device busy". After this grep just idles as according to "top -m io -o total" the I/O usage of grep is nonexistent. Same behavior is true under FreeBSD 8.0, but last information sent to stderr is "grep: /tmp/.wine-0: Permission denied" on my installation. In case of Debian, last output to stderr is "grep: /proc/sysrq-trigger: Input/output error". If I check the I/O usage of grep process under Debian, it is following: root@Debian:~# iotop -bp 22439 Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 22439 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % grep -r -I -D skip 10.10.10.99 / ^Croot@Debian:~# What might cause this? Is there a way to view which file grep is currently processing in case lsof is not present? I'm able to use lsof under Debian and looks like the problematic file name there is "0xc6b2c230 file struct, ty=0, op=0xc0d34120". I'm not sure what this is.. I'm not able to use lsof or fstat under FreeBSD. PS: I know I could use find utility, but this is not the question.

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• MAMP Pro .xip.io, fixing urls with htaccess

  - by user3540018

  I've got all my websites set up with MAMP Pro. For instance, I got it set up, so when I go to example.com, the browser displays the website that's set up on my iMac. Now, I wanna get MAMP Pro to work so I can view my website on my other computers/devices (which are all hooked up on the same network.) So far all I had to do is check the checkbox "via Xip.io (LAN only)", and now I can view my website on my other computers/devices within my LAN by simply going to example.com.10.0.1.13.xip.io. Problem is, whenever I'm on this other computer/device, when I click on the links, I get 404 error. ie. whenever I go to example.com/news, I get the 404. But when I go to example.com.10.0.1.13.xip.io/news, THEN I get the right page. So in order to solve my problem I need to rewrite the urls. So whenever someone clicks on a link ie. goes straight to example.com/news, he'll go to example.com.10.0.1.13.xip.io/news. I don't want to change all the links in my MySQL file, but I believe I can do it simply with the htaccess file. I've opened the htaccess file and added the last two lines, but it just doesn't work. <IfModule mod_rewrite.c> RewriteEngine On # Send would-be 404 requests to Craft RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !^/(favicon\.ico|apple-touch-icon.*\.png)$ [NC] RewriteRule (.+) index.php?p=$1 [QSA,L] RewriteCond %{HTTP_HOST} ^example\.com RewriteRule ^(.*)$ http://www.example.com.10.0.1.13.xip.io/$1 [R=permanent,L] </IfModule> Or perhaps I don't need to change the htaccess file, is there something that I could be missing in the MAMP Pro settings, or perhaps a MAMP extension that I need?

  Read the article

• how would it be possible to discover a cable modem's MAC remotely?

  - by amateurenthusiast

  i was reading the back archives of a canadian privacy law blog, and he linked to a judicial decision. apparently as part of an investigation in which were used yahoo chat and google's old 'hello' image trading program the officer was able to determine a suspect's modem's MAC address: In order to determine who STEPHTOSH was, the officer did a trace on a programme called WHO IS in an effort to learn from where STEPHTOSH was coming. WHO IS is a command program available to the public. The officer was able to ascertain that the person using the name STEPHTOSH was a Rogers Internet customer. The officer was able to obtain the Internet Protocol address, also known as the I.P. There is only one location for an I.P., which is unique to that subscriber. By use of the website known as DNS STUFF.com, one is able to find with which company this I.P. is registered. It was ascertained that the I.P. address used by STEPHTOSH was registered to Rogers Cable, from the Toronto area. The officer also learned the Cable Modem MAC address used by STEPHTOSH. This was all the information the officer was able to amass. now it was my understanding that the MAC address of any given device can only be accessed if you're only one 'hop' away on the Internet. the suspect in question was in Markham and the officer part of the Toronto Police, so it's conceivable that they both might have used Rogers internet. but would that still put them only one 'hop' away from each other? i thought the first hop after the modem was usually the ISP? and if he'd used a netBIOS query against this guy's machine it would return the ethernet card's MAC, not the modem's. so is this guy on the same rogers subnet as the suspect's cable modem, is that functionality part of google's Hello (i could only think that it would be possible if Hello operated as a virtual LAN or something), does the officer have remote access to the arp caches of the routers at Rogers or is he just full of crap and lying to make his case stronger?

  Read the article

< Previous Page | 774 775 776 777 778 779 780 781 782 783 784 785  | Next Page >