Search Results

Search found 2154 results on 87 pages for 'bios'.

Page 78/87 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Two VGA monitors on Lenovo IdeaCentre H520 Desktop

  - by Sebastian-Laurentiu Plesciuc

  I recently bought a Lenovo IdeaCentre H520 computer and two VGA LED monitors. This particular PC has a dedicated NVIDIA Geforce GT630 video card and an integrated Intel HD Graphics 2500 video card. Both cards have VGA out. The Geforce card also has a HDMI out. I have installed Windows 8 and I can't seem to use both cards. I have connected both monitors, one to the VGA out of the Geforce card and one to the VGA out of the integrated card. I looked through the BIOS options for Video and I can only select the dedicated one, the integrate one or the Auto option. This kinda sucks. I was wondering what kind of options I have available. I have a VGA female to DVI A male adaptor, I was wondering if it could work if I can hook it to a DVI A female to HDMI male adaptor and plug one monitor into the VGA out of the Geforce video card and the other through both adapters to the HDMI out. Any chance this could work? I was looking online for a VGA to HDMI live cable but it's kind of expensive.

  Read the article

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• Building My First Computer And Suprise It Isn't Working

  - by BobbShots

  I've had many years of experience working on and around computers, but this was my first foray into building one completely from scratch. So far that foray has been a disaster. My rig is completely assembled, and on its maiden power-up plus many power cycles I noticed three things: There were a few beeps from the BIOS POST upon powering up the first time, but I wasn't paying attention completely to the sequence. However, every time after that there are 0 POST beeps, even after taking off all hardware except the CPU and MB. There was no video being sent to the monitor. I run a HDMI cable from my video card to the monitor. The video card was LOUD. My card is a Sapphire Radeon HD 5870 which is known for not only being a powerhouse, but being pretty quiet. A few times during my power cycles it ran a lot quieter, but most of the time it was just super loud. Can anyone provide help for any of these issues? My MB, CPU, and Video Card are: MB: ASUS P6X58D Premium LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX Intel Motherboard CPU: i7 920 Video Card: Sapphire Radeon HD 5870

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• Gigabit LAN not working on ASUS M2N-MX

  - by chmod

  Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

  Read the article

• configure a Macbook Pro to use external monitor at boot (Debian Linux)

  - by Eric

  In the spirit of reuse, I've installed Debian (version 6.0.5 "squeeze") on my wife’s old Macbook Pro (circa 2009 or so), to repurpose it for various tasks. The catch is the display is flaky. It will last a random amount of time, between 2 minutes and 2 hours, before freezing and graying out. This is a known issue with that generation of MBP. Fortunately it’s no problem for me, as I plan to use it with an external monitor anyway. Which brings us to the problem: How do I configure this thing to output to the external display by default, and hopefully disable the built-in LCD? The ideal solution would be to modify a setting in the EFI (BIOS), but I’m not holding out much hope for that. Next best thing would be a kernel option I can pass to the NVIDIA driver. What won’t work is a solution that doesn’t give me a display until X starts. I need to have console access, especially given that the built-in LCD is dying, and any day now might give out completely. So far I haven’t been able to find anything online. lspci says I’ve got an NVIDIA GeForce 9400M Help is much appreciated! Eric PS if this question is better suited to the Unix & Linux area, pls advise and I will move it.

  Read the article

• no administrator password for Windows 7

  - by huskergirl78

  I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

  Read the article

• Dell PowerEdge T710, add a new hard disk, how to?

  - by user1340802

  I need to add a new hard disk to a PowerEdge T710 running on Vmware EXSI 4. this hard disk is a 'normal' desktop hard disk 1TB (that is it is not coming from Dell, I also have no rack for it to plug it inside any of the front bay) I would like to add this disk for a virtual machine needing space, the most easily as possible. I have find that there is an avaiable sata cable with its electric power, so may I just add the disk plugging these and using the empty 5"1/4 slot available under the CD drive (with a 5"1/4 - 3"1/2 bay adaptater) ? (even if this way it seems that i bypass the raid controller that own the front bay with racks)) that way i think could be easier than adding the disk to the already defined Raid (btw i am also not sure on how to do these but i would not risk to mess the already working things) what are the other operations that i would have to do to ? (sorry I am a real beginner on Vmware EXSI and PowerEdge management :/ i have seen that there is some management from Bios (CTRL+R as start up) so that the disk will be seen or initialize it. I am really not sure of the steps needed...) thank you, best.

  Read the article

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• XP VM not detecting USB keyboard or mouse from Windows 7 host

  - by Ian Kemp

  I've been using a Windows XP Pro VM (32-bit, SP3) for months on my work PC (Windows 7 64-bit) with no problems, with a PS/2 keyboard and a standard optical USB mouse. Today I copied this VM onto my home PC, which is also Windows 7 64-bit but with a G15 USB keyboard and MX518 USB mouse. For some reason the VM does not accept input from the keyboard or mouse, which makes it almost impossible to use. (Unity works but is not an option). Both my home and work PC are running VMware player 3.1.0. My keyboard and mouse show up as USB devices in the bottom-right of the VMware Player window, and if I click them I have the standard option to "Connect (Disconnect from host)". I have selected this option for the keyboard, and then the VM happily accepts keyboard input, but of course my host PC no longer does. It seems like VMware is seeing my keyboard and mouse as USB devices and not input devices. I've tried sending the keyboard input to the guest and reinstalling VMware Tools, but that achieved nothing. I'm certain it's a problem with the VM, and not the XP install, as I also can't use F12 to enter the VMware BIOS when the VM is powering up.

  Read the article

• Booting Ubuntu as VM with KVM on Ubuntu 12.04

  - by CrazycodeMonkey

  I am trying to boot my very first VM using KVM. I have Ubuntu 12.04 installed, i made sure the BIOS had the right virtualization flag enabled for intel processor by running kvm-ok. I have researched this on google and all the instructions that i have found so far are outdated. for e.g. most instructions talk about booting a virtual machine with the following commands qemu-img create -f qcow2 foo.img 100G --- create a virtual disk for your VM kvm --name foo -m 1024 -hda foo.img -cdrom whatever.iso -boot d -- This runs kvm. This command line is incomplete. First you need to be root to run this. Second- it is missing option for the video device. When you run this command you get the following error "Could not initialize SDL(No available video device) - exiting" Googled this error and looked it up on stackover flow http://stackoverflow.com/questions/4841908/sdl-init-failure-reason-is-no-available-video-device The answer provided here does not work on Ubuntu 12.04 Googled this problem further and found out that i need to specify a video device so I finally ran the following command sudo kvm --name mymachine -m 8096 -hda myimage.img --cdrom ubuntu.iso -boot d -vga cirruss -k en-us -vmc :0 This was after I had created the myimage.img image on the drive. Now this command does not give me an error but it just hangs. Does anyone have clear instructions on how to run a VM using KVM on Ubuntu?

  Read the article

• Hard Drive Compatibility with Motherboard

  - by Wesley

  Here are the current specs to put things in context: ECS P4VXASD2+ V5.0 Intel Pentium 4 Northwood 2.8 GHz 2x 512MB PC2100 DDR266 SDRAM Maxtor DiamondMax 10 250 GB PATA (IDE) HDD Gigabyte 52x CD-ROM NVIDIA TNT2 Pro 16 MB OKIA 300W ATX PSU USB bracket Modem PCI Before, I actually had a 300 GB hard drive installed. However, I read the FAQ for the motherboard and discovered that a maximum of 250 GB hard drive was supported. So I ended up finding the one listed above and put that in. However, upon booting up, I reset the BIOS to defaults and auto-detected all the drives installed. The 250 GB came up as something like 251.0 GB. I didn't think much about it until I tried to boot up a Windows XP installation disc. It booted up successfully and run for about a minute before the computer randomly rebooted. I've made sure that all the jumpers and settings are correct and everything has been installed correctly. I've tried running it without the addons and one stick of RAM but still the same thing. What else could be causing this problem?

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• PC dies when running at 100% CPU

  - by user155631

  I recently wrote some Java code to generate images of the Mandelbrot set (fractal). I made use of the new Fork/Join facility in Java 7 to run separate threads on all four cores (2 real, 2 virtual)simultaneously, using a large number of iterations for greater accuracy. The problem is, the process runs fine for about a minute, and then it's as if someone has pulled the plug and the PC just dies. I thought it must be the CPUs overheating, so I ran Real Temp to monitor the temperature. It's an Intel i3 processor. I can see the temperature creeping up to 70 degrees, and then it seems to level off there and run for about another 30 seconds before dying. According to Real Temp, there's still a gap of 35 degrees between the actual temperature and TJ max. I also tried disabling "CPU TM function" in the BIOS, but the problem still occurs. A colleague suggested that it might be a power supply problem, so I borrowed a more powerful PSU (can't remember what wattage it was, but it's higher than mine which is 500W). The exact same thing still happens though. Is anyone able to suggest what the problem might be, or what I can try next?

  Read the article

• HP EliteBook 8440P - USB ports stop working on docking station

  - by r0ca

  I have a HP Elitebook 8440P running Windows XP Pro SP3. I installed it on my docking station and everything went smooth for a while. Last week, my mouse and any other USB devices stoped working sudenly... It was working fine on my laptop itself but nothing on my docking station. LCD attached monitor works and same for LAN and PS2 keyboard. I updated the BIOS, Chipset, Video Drivers, also changed my docking station by a brand new one but the problem still comes back. I also noticed something in Device Manager... A Generic USB Root Hub has an error on it, a Yellow/Orange exclamation mark. I tried to update that driver but no luck. Windows is unable to process it. This seems to be the problem but can't fix it. I may only re-image my laptop but for me, I need to avoid that since I have so many apps installed on it. If anybody has any advice, I'll take it!

  Read the article

• How can I add a second hard drive to a previously configured UEFI/ACHI Windows 8 machine?

  - by pflyer

  Recently purchased a new Windows 8 PC. It came with one hard drive. I want to a second hard drive to it. This second hard drive is my data hard drive from my previous computer. However, I have run into issues when the system accesses it. The drive is found in the BIOS. But is not seen by Explorer or Disk Management. I have added the drive to the next available SATA slot: SATA 2. The machine is a UEFI/ACHI based machine. In my reading I have found people documenting the following: 1) adding multiple partitioned hard drives (like mine is) to UEFI based machines is not possible 2) I have seen it suggested that you can only add blank hard drives to UEFI based machines. However, in doing so, I did not have success. I tried to add it as a hard drive with unallocated space and then as a hard drive with a single simple partition. Both attempts failed. My ultimate question: What is the proper procedure for adding a second hard drive to a UEFI/ACHI machine? I do not want to reinstall the OS and start from scratch as I have seen suggested elsewhere. There has to be a way to accomplish this without all that hassle. Thanks in advance for your help.

  Read the article

• SATA DVD drive refuses to read movie DVDs

  - by poke

  Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

  Read the article

• DVD-burner disappears when using grub

  - by drblah

  This is a rather annoying problem I have with Linux on my laptop. Whenever I install any Linux distro that relies on grub (which is about 99 % apparently) it will mess up my DVD-drive and the drive will not be recognized after booting, no matter the OS (Ubunntu, Arch, Windows Vista or 7). I know the problem has nothing to do the DVD-drive itself, because I bought a new one a few months ago. I am also sure that grub is messing the drive up, because I have tried to use LILO, which worked fine (except for horrible boot times.) This problem have persisted through about 3-4 years and it is a pretty bad show stopper whenever I want to work with Linux. I had hoped it would get fixed over time, but no one seems to have the exact problem I have. The drive is connected with an IDE connection. Update: The old drive was a Toshiba Samsung SN-S082. I don't know the model number of the new one, but it is HP (I think). Things I have tried to fix it: Mess about with some BIOS settings like enabling AHCI and change some IDE settings. Installing a different boot loader DOES fix the problem but I would like to use grub.

  Read the article

• Docking Station Sound Doesn't Work on Dell D830 with Windows 7

  - by cisellis

  EDIT: I can only mark one answer as the correct one but the actual solution was a combination of two comments (updating the BIOS to A15 AND installing the Sigmatel audio drivers). I have a Dell Latitude D830 laptop that is running Windows 7 Enterprise x64. I connect to a docking station during the day with multiple monitors, a keyboard and a mouse. Everything runs with no problems including most of the docking station ports (usb, monitors, etc.) However, the sound port from the docking station does not work since the upgrade to Windows-7. Even with the laptop plugged in, the sound always comes out of the laptop, not the headphones plugged into the docking station. Here's what I've tried: I've seen other issues like via Google this that seem to be mostly unanswered. I found one or two that referenced using the Vista x64 drivers, especially the Nvidia drivers. I do not have an Nvidia chipset but I've reinstalled the sound drivers and that has not helped. I don't have a support contract and considering the cost is usually high to call Dell, that's not an option. Dell's forums are pretty much a wasteland and I've found no help there. Since this is a docking station I thought I might need to try the SATA or Intel chipset drivers from the dell site instead, however I'm not really sure and I need to work on this laptop in the meantime. I can't really afford the downtime to experiment with random drivers all day in case they turn out to be incompatible (Dell still hasn't added Windows 7 to their support site as far as I can tell). Does anyone have any other ideas? Has anyone had this issue and solved it? If so, how? Thanks in advance for your help.

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• CPU operating temperature ranges

  - by osij2is

  I have an AMD Phenom II 960T with 2 cores unlocked for a total of 6 cores. I don't overclock at all. I have a Arctic Cooling ACALP64 Heatsink/Fan installed. I'm currently running ESXi 5.0 so I have to go into the BIOS to read the CPU temperatures, which at idle seem to be in the 71-74C range. To me, this is pretty high, but I cannot find any official temperature ranges that AMD says the CPU can work well within. There seems to be a lot of questions on superuser and numerous forums around CPU temperatures but no one seems to have a clear consensus as to what the manufacturer temperature ranges are for specific CPUs. I've tried searching through AMDs site to no avail. At this point, I'd be willing to shut off the 2 extra cores if it keeps the heat down but until I get some sort of tolerance or range for temperature, I have no idea if the CPU is being damaged or not. Can anyone point to a direct source, article, FAQ from AMD that specifically states their CPUs temperature range? Or are CPU temperature ranges so varying that there's no possible baseline? Am I being too paranoid about this? To me, anything over 65C is a bit much and if I'm in the low-mid 70s range with NO VMs running, what can I expect if I have several VMs running?

  Read the article

• Windows 8 Install Hanging at first white-font boot splash

  - by Omega

  I'm trying to install the Windows 8 preview on my Samsung Series 9 (2012, Ivy Bridge). I've done a bit of a custom scheme with this one: I'm using EFI/UEFI on this system. I've seen no indication that this system supports secure boot (yay!) My SSD is set up with GPT Ubuntu is already installed and working great via UEFI. I'm trying to boot the Windows 8 install from a USB stick via UEFI I don't have access to a CD drive. The problem is that the boot seems to hang at the very first splash screen that looks like this. White windows font, the little beads don't show up. My USB stick has an activity light and it does blink for the first few seconds, but then goes back to it's "nobody is talking to me" idle pulse. What I know: UEFI booting is definitely working. Windows 8 for those few seconds seems to have some kind of access to the USB drive. My Series 9 is running the latest BIOS/firmware. Any idea what I might be able to do to get Windows 8 installed??

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >