Search Results

Search found 2154 results on 87 pages for 'bios'.

Page 79/87 | < Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >

• How do I find the cause for a huge difference in performance between two identical Ubuntu servers?

  - by the.duckman

  I am running two Dell R410 servers in the same rack of a data center. Both have the same hardware configuration, run Ubuntu 10.4, have the same packages installed and run the same Java web servers. No other load. One of them is 20-30% faster than the other, very consistently. I used dstat to figure out, if there are more context switches, IO, swapping or anything, but I see no reason for the difference. With the same workload, (no swapping, virtually no IO), the cpu usage and load is higher on one server. So the difference appears to be mainly CPU bound, but while a simple cpu benchmark using sysbench (with all other load turned off) did yield a difference, it was only 6%. So maybe it is not only CPU but also memory performance. I tried to figure out if the BIOS settings differ in some parameter, did a dump using dmidecode, but that yielded no difference. I compared /proc/cpuinfo, no difference. I compared the output of cpufreq-info, no difference. I am lost. What can I do, to figure out, what is going on?

  Read the article

• EC2 AMI won't boot after edit

  - by Eric Lars0n

  I did something stupid, I got a new laptop and copied everything over to the new one, then wiped the old one clean. Then I realized that I forgot to copy the private key out of .ssh that I use to connect to my AWS EBS backed instance. So I can't log in to my custom AMI. So I created a new Volume from the Snapshot of the AMI, then started up a public instance and attached the Volume to it, edit the sshd_config to allow for password log in. Unmounted the volume, detached it, made a snapshot of it, then made a new AMI from the snapshot. The new AMI launches, but never passes the Status Checks and is not reachable. What am I doing wrong? Or alternatively how can I fix my problem? Edit: Adding some of the console output Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize NET: Registered protocol family 2 Registering block device major 8 XENBUS: Timeout connecting to devices! Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,0)

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• CPU not working on a specific motherboard

  - by Shaman

  I'm making a computer for someone and I met a weird problem. The CPU that I have doesn't work on this motherboard. The CPU is an Intel Pentium D 925 and the motherboard is an ECS G41T-M6, which in theory should work together. The only thing reused is the power source(400W). When I start the computer, the fans start, and that's it. The BIOS doesn't boot. I tried my own power source (600W Corsair) and nothing. Removed the RAM, no warning. In desperation I tried the last thing, swaped my own CPU with this one (Core2Duo E7200). Lo and behold, it worked. Both. The Core2Duo worked on the ECS with the old power source and the RAM that I used in the first place, and the Pentium D worked on my Gigabyte G31M-ES2L. What I discovered was that the Pentium D didn't receive power on the ECS, because I tried running it without the cooler and it remained at room temperature. On a side note, I also removed the HDDs just in case. So, in conclusion, any ideas? I can't return it, and I can still use it to upgrade another PC, but I would really prefer not to buy another CPU if possible.

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• Computer not finding hard drives on boot -sometimes-

  - by todd.pund

  Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

  Read the article

• Can I clone my hard drive to an external and boot from the clone?

  - by willbuntu

  First thing: I am not asking what software I'm supposed to use. I already know the answer: Ghost (proprietary), Clonezilla, and dd (if I'm careful). What I really want to know is if it is possible to (essentially) bit-for-bit clone my entire installation (OS, installed software, activation(s), etc.) to an external USB hard-drive, and then boot off of that (if I need to, I know how to edit BIOS settings and use Plop boot manager), and work with it day-to-day as if there was virtually no difference from using my internal HDD now. Again, I'm not asking how to install Windows to an external (because I know I'd need to do some special workaround), I'm asking if I can clone everything and boot off of it. In case you're wondering why I'm going to this trouble: I'm using a Lenovo Essentials laptop that has an unmodifiable partition table (due to recovery crap), and has all 4 of its partitions spoken for (3 primary, one extended, cannot change the extended). Anyway, my thought is that if I can clone everything and boot off of it when I need to, and just have a Linux distro on the internal HDD, then that could work.

  Read the article

• Starting old computer - nothing shown on screen at boot

  - by Jonas

  I'm trying to start an about 10 years old PC computer. But nothing is shown on the screen, and it beeps everytime I press a key on the keyboard. I can press Ctrl+Alt+Del to reboot the computer. The monitor is newer and seem to work with other computers. I don't see anything from POST/BIOS at start or later. I have tried to change to another graphic card, but it didn't change anything. What can I do to solve this problem? Update: I have now tried with another computer (the one where the "another graphic card" came from) and I got the same problem. I doesn't show anything on the screen. Both these computers had a GeForce2 MX 400 graphic card. I tried with another computer screen it didn't work - it was showing "signal out of range". So is the graphic card GeForce2 MX 400 too old for newer TFT-monitors? I tried with a third computer so I know that the monitors are working, and both monitors work fine with that computer.

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• What could cause Windows 7 to hang whenever I install something?

  - by Larsenal

  I've had this problem when installing several different programs (iTunes, Adobe Acrobat Reader just to name two). Regardless of what the program is, the install usually gets at least 90% through the process and then just hangs. I don't see anything bad in the event log besides the following (and this didn't occur exactly at the time of install): wuaueng.dll (964) SUS20ClientDataStore: A request to write to the file "C:\Windows\SoftwareDistribution\DataStore\DataStore.edb" at offset 16252928 (0x0000000000f80000) for 32768 (0x00008000) bytes succeeded, but took an abnormally long time (185 seconds) to be serviced by the OS. This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. I've run check disk and it passed. I've had some problems with BIOS settings in the past with Windows 7, but I'm not sure whether that could be related. Update... I also see this error in the event log: Volume Shadow Copy Service error: Unexpected error querying for the IVssWriterCallback interface. hr = 0x80070005, Access is denied. . This is often caused by incorrect security settings in either the writer or requestor process. Operation: Gathering Writer Data Context: Writer Class Id: {e8132975-6f93-4464-a53e-1050253ae220} Writer Name: System Writer Writer Instance ID: {33493f01-ac1b-4efb-a378-3053ab03100d} One last wrinkle.... I see "Previous versions" of c:\ which look like they correspond to the time of attempted installation.

  Read the article

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• need to bring back win 7

  - by user290513

  I like making music and playing games and occasionally do some Photoshop. I had a windows 8 computer but my mouse pointer always got stuck, so to try out something new I installed Ubuntu. here is how I installed it: Went to advanced statup options clicked on "use a device" after plugging in my bootable USB with Ubuntu replaced my windows 8 and installed Ubuntu 14.04 LTS I hope I did it correctly though. So after a few months I could've really find out a good Audio Production (not LMMS, because I use Stagelight) software nor something that could be familiar to the UI of Photoshop. So I decided to bring back Windows, but because of the bad experience of 8 I thought about bringing back win 7 So I used an app named WinUSB to make my bootable USB drive after formatting it to NTFS in GParted But when I go to my grub menu, my USB doesn't show up and my PC being a UEFI device. I don't know how to get to the bios of my device. Can somebody tell how to install Windows 7 completely and deleting Ubuntu or at least give me a link to a tutorial. I have a netbook: it is an Acer Aspire One 725. I'm fine with using commands in terminal and another thing that my laptop doesn't have a CD drive or reader, I can't put a CD inside

  Read the article

• New PC: win7 install issues with 2x3TB in RAID1

  - by goober

  Background / Components Not sure what I've done wrong. Built one PC before successfully in a similar way but this one seems to be struggling. I have the following components: ASUS P8Z68-V/Pro Gen 3 (updated to latest firmware) 16GB (2x8GB) RAM corsair hx850 power supply 2x3TB drives on the intel z68 controller 1x128GB SSD on the Marvel controller sapphire 7950 The problem I set up my 3 TB disks in RAID1 controller appears to recognize them fine during boot as one 2.7TB raid1 volume windows setup sees two disks, both 746 GB, but will only let me install to one and appears to work fine. windows appears to install fine after installer reboots, I receive "windows failed to start" error referencing code 0xc000000e and "\Windows\system32\winload.exe every time I do an install, a new additional "win7" entry is added to the boot menu; all lead to this error. What I've tried: updated the BIOS to the latest firmware attempted to repair the install tried clearing / removing raid / re-raiding drives tried formatting the drives during install attempted to clear the menu Of entries (can't figure out how to do that) No matter how many times I destroy the raid array, format the disks, etc. the boot entries keep piling up. Any idea where I'm going wrong?

  Read the article

• Can a OS be copied from one hard drive to another and still boot?

  - by AlexMorley-Finch

  Background My computer gets stuck on the make and model screen after the BIOS screen, aka the Toshiba screen. After some research I've realized that the problem is the hard drive. I'm using an old 250gb model that USED to be used for backup purposes, however I loaded windows 7 ultimate onto it This hard drive has trouble getting up to full RPM therefore cannot boot correctly until its warmed up. meaning that my pc needs to be restarted several times before it boots (once it took my 13 reboots to get my pc on!) From my research its either that, or lack of power supply, and I've tried multiple PSUs. Question I have my OS and all my files on this 250gb HDD... If I were to literally open the explorer, and copy EVERYTHING (including hidden files obviously) from this 250gb, to a spare 500gb I've got knocking about... Will it boot if I just copy everything? I cannot be bothered to load another OS onto my PC so if there is a way I can just copy the existing one over from one HDD to another and have it boot normally. This would be epic! I've heard about HDD cloning software. But before I purchase and/or download this software, I need to know if i can just copy the OS over through the windows explorer

  Read the article

• Getting a "CPU over temperature error", but temperatures seem to be normal

  - by Luis Parker

  I built a PC with the following parts: CPU: i5-2500 Motherboard: Asus P8H67-M EVO rev 3.0 RAM: G-Skill Ripjaws Series 8GB (2 x 4GB) DDR3 1333 Video: GTX 560-Ti 1GB I used a crappy (but functioning) old case and a 500W Powercooler supply. The rig also includes 3 HDs and a DVD-RW. Whenever I push the system mildly it resets right away (looks more like power off/power on) and gives me a "CPU over temperature error". However, BIOS always reports <65ºC for the CPU at the moment of the reset, same as Core Temp and RealTemp. This is RealTemp's log since launching BF3 until the reset (just over 1 minute, as you can see) Just to be sure I've checked the CPU cooler and re-applied the thermal paste twice, but nothing changed. I'm not overclocking at all. What am I missing here? Could it be that the old power supply is generating this error? Maybe the mobo isn't reporting temperatures correctly? I don't have a clue on how to troubleshoot this, help Thanks in advance!

  Read the article

• Monitor attached to motherboard is out of frequency

  - by Neilvert Noval

  I don't know if this is appropriate to ask it here in superuser. Please, just route this to appropriate stackexchange site if found unrelevant. Here's my scenario. I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is: Out of frequency. Current frequency is 89Hz. The operating output of my monitor is (around) 60-70Hz. I would like to get this thing work. How can I let my CRT display properly? I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info: My monitor is attached directly to the built-in video adaptor of my motherboard. (No additional video cards) Install of OS is complete without errors. Please help.

  Read the article

• Compatibility of Fedora install on a Hybrid drive

  - by kjh

  I recently bought un ultrabook with a 500gb/32gb sdd hdd hybrid drive, and I'm having trouble replacing windows on it with fedora seventeen. it errors out saying there was an unhandled exception. Is linux compatible with hybrid drives? or can the operating system on a hybrid drive not be replaced? Edit: here are the steps I select special storage devices because it ignores my hard drives otherwise at this point i get the message: "Disk contains bios raid meta data, disk sda will be ignored" I can pick a hostname, select my timezone and set a password at the install type screen, no matter what I select (use all free space, replace linux systems, create custom partition etc..) once I click next, it says "an unhandled exception" has occured. and I can no longer proceed with installation. Here is the error message: anaconda 17.29 exception report Traceback (most recent call first); File "/usr/lib64/python2.7/size-packages/pyanaconda/bootloader.py"; line 183 self.stage1_drive=self_drives[0] File "/usr/lib64/python2.7/site-packages/pyanaconda/rw/cleardisks_gui.ph"; line... and tons of more lines like that

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• Latitude D600 USB port problem

  - by Moab

  Both USB ports stopped communicating on my D600, they have power, my optical mouse still lights up, no device works on the ports, everything is fine in Device manager in Dual boot XP and W7. Checked the bios, not much in there for USB. No usb device shows up when I use the F12 boot device menu either, so it must be some hardware issue. I have another hard drive with Ubuntu on it, popped it in and USB does not communicate with it either. Appears to have 5v but no communication, any Ideas besides another motherboard or USB card for the pcmcia slot (these don't work to well from my research)? I mostly use them for mass storage devices and pcmcia slots don't supply enough power for these devices. Thanks to all who answer with last ditch efforts. I hate to give up on it, its been good to me and still runs rather well for its vintage. EDIT: I did inspect the ports with a flashlight and did a partial disassembly of the laptop in an attempt to check the solder joints, but would require complete motherboard removal to see them, that is where I stopped. .

  Read the article

• Get Matrox Millenium video card working in Ubuntu 9.10

  - by wcoenen

  I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

< Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >