Search Results

Search found 25284 results on 1012 pages for 'test driven'.

Page 784/1012 | < Previous Page | 780 781 782 783 784 785 786 787 788 789 790 791  | Next Page >

• Using smartctl to get vendor specific Attributes from ssd drive behind a SmartArray P410 controller

  - by Lairsdragon

  Recently I have deployed some HP server with SSD's behind a SmartArray P410 controller. While not official supported from HP the server work well sofar. Now I like to get wear level info's, error statistics etc from the drive. While the SA P410 supports a passthru of the SMART Command to a single drive in the array the output I was not able to the the interesting things from the drive. In this case especially the value the Wear level indicator is from interest for me (Attr.ID 233), but this is ony present if the drive is directly attanched to a SATA Controller. smartctl on directly connected ssd: # smartctl -A /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0000 100 000 000 Old_age Offline In_the_past 0 4 Start_Stop_Count 0x0000 100 000 000 Old_age Offline In_the_past 0 5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 8561 12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 55 192 Power-Off_Retract_Count 0x0002 100 100 000 Old_age Always - 29 232 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 0 233 Unknown_Attribute 0x0002 088 088 000 Old_age Always - 0 225 Load_Cycle_Count 0x0000 198 198 000 Old_age Offline - 508509 226 Load-in_Time 0x0002 255 000 000 Old_age Always In_the_past 0 227 Torq-amp_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 228 Power-off_Retract_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 smartctl on P410 connected ssd: # ./smartctl -A -d cciss,0 /dev/cciss/c1d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net (Right, it is complety empty) smartctl on P410 connected hdd: # ./smartctl -A -d cciss,0 /dev/cciss/c0d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Current Drive Temperature: 27 C Drive Trip Temperature: 68 C Vendor (Seagate) cache information Blocks sent to initiator = 1871654030 Blocks received from initiator = 1360012929 Blocks read from cache and sent to initiator = 2178203797 Number of read and write commands whose size <= segment size = 46052239 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 3363.25 number of minutes until next internal SMART test = 12 Do I hunt here a bug, or is this a limitation of the p410 SMART cmd Passthru?

  Read the article

• Puppet file transfer slow

  - by Noodles

  I have a puppet master and slaves in different datacenters. The latency between them is ~40ms. When I run "puppet agent --test" on a slave to apply the latest manifest it takes ~360 seconds to finish. After doing some digging I can see the main cause of the slow down is file transfers. It seems it's taking ~10 seconds to transfer each file. The files are only small (configuration files) so I can't understand why they would take so long. This is an example of a file in my manifest: file { "/etc/rsyncd.conf" : owner => "root", group => "root", mode => 644, source => "puppet:///files/rsyncd/rsyncd.conf" } Running puppet-profiler I see this: 10.21s - File[/etc/rsyncd.conf] It also seems I cannot update more than one server at once using puppet. If I run two servers at the same time then puppet takes twice as long. I have changed the puppet master from using webrick to mongrel, but this doesn't seem to help. This is making deploying changes painful. A simple config change can take an hour to roll out to all servers.

  Read the article

• Is it possible to be a professional studying on your own?

  - by Marc Jr

  I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

  Read the article

• How do I make dnsmasq serve IP addresses via IPoIB?

  - by Matt

  I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

  Read the article

• Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

  - by Shadow00Caster

  I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

  Read the article

• Run FTP session from bash script

  - by Adam Salkin

  I'm trying to write a BASH script to test if an FTP site that I own is running. I therefore want the bash script to connect to the FTP site, log in with a dummy account and redirect the output to a file that I can then grep to confirm that the login succeeded. (I know that putting user/pass in a file is not recommended, but this dummy account is chrooted to one empty directory and can't escape to the shell, and in any case I'm the only user who can login to a shell prompt.) I'm using the BASH shell on Ubuntu. I created a file called "ftp-dummy" which looks like this username password And I then did this from the prompt: adam$ ftp my.ftpsite.com < ftp-dummy This does not work - I don't see the normal welcome message and the output is: Password:Name (my.ftpsite.com:adam) : I tried removing the space between the < and the filename - same result. If I redirect the output to a testfile, the testfile shows: Name (my.ftpsite.com:adam): ?Invalid command And I still get a Password prompt on STDOUT I also tried using echo and get the same result: echo -e "username \npassword \n" | ftp my.ftpsite.com I don't see why I'm not seeing the normal welcome message or why the input is not being read from the file. Any help would be much appreciated. Thanks, Adam

  Read the article

• Installing Linux on an Asus p8z68-m PRO Motherboard

  - by Holland

  Here is a challenge: how is this done? I've tried disabling the ASM1061 controller in the Onboard Devices section, using Wubi, booting from USB (as I don't have a DVD drive, yet), and even booting from RAID/IDE (with AHCI as the default) to do this. Still, no dice. Google shows up virtually nothing related about Linux and this mobo, apart from a people just saying "disable ASMedia" (which, I assume is the ASM1061 controller, as that's all I see - apart from the USB 3.0, which I disabled already) and it hasn't really helped much. Thus, what is wrong here? Edit My problem is that I cannot boot Linux via USB or a simple Windows installer such as Wubi (for Ubuntu). I wind up getting error messages along the lines of write cache failed, along with many other cryptic error messages similar to the following: [ 1400.351374] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled [ 1400.353433] sd 4:0:0:0: [sdb] Asking for cache data failed [ 1400.356601] sd 4:0:0:0: [sdb] Assuming drive cache: write through This seems to be common for Asus P8Z68-M Pro motherboards, with the only notable solution being to "disable ASMedia", which, as I said before, I'm guessing is the ASM1061 controller on the motherboard. Despite already disabling this, I have tried this with both Fedora and Ubuntu without any success. I need to know what I can do about this; has anyone ran into something similar or heard about this issue before? I know these motherboards are relatively new...

  Read the article

• How to Change the Kerberos Default Ticket Lifetime

  - by user40497

  Our KDC servers are running either Ubuntu Dapper (2.6.15-28) or Hardy (2.6.24-19). The Kerberos software is the MIT implementation of Kerberos 5. By default, a Kerberos ticket lasts for 10 hours. However, we'd like to increase it a bit (e.g. 14 hours) to suit our needs better. I had done the following but the ticket lifetime still stays at 10 hours: 1) On all the KDC servers, set the following parameter under [realms] in /etc/krb5kdc/kdc.conf and restarted the KDC daemon: max_life = 14h 0m 0s 2) Via "kadmin", changed the "maxlife" for a test principal via "modprinc -maxlife 14hours ". "getprinc " shows that the maximum ticket life is indeed 14 hours: Maximum ticket life: 0 days 14:00:00 3) On a Kerberos client machine, set the following parameters under [libdefaults], [realms], [domain_realm], and [login] in /etc/krb5.conf (everywhere basically since nothing I tried had worked): ticket_lifetime = 13hrs default_lifetime = 13hrs With the above settings, I suppose that the ticket lifetime would be capped at 13 hours. When I do "k5start -l 14h -t ", I see that the end time for the "renew until" line is now 14 hours from the starting time: Valid starting Expires Service principal 04/13/10 16:42:05 04/14/10 02:42:05 krbtgt/@ renew until 04/14/10 06:42:03 "-l 13h" would make the end time in the "renew until" line 13 hours after the starting time. However, the ticket still expires in 10 hours (04/13 16:42:05 - 014/14 02:42:05). Am I not changing the right configuration file(s)/parameter(s), not specifying the right option when obtaining a Kerberos ticket, or something else? Any feedback is greatly appreciated! Thank you!

  Read the article

• WT-NMP - PHP-CGI randomly stops running with no error log

  - by alexfontaine

  We have recently installed WT-NMP and are currently running Php-Cgi with php 5.4.24. We are running fairly simple php scripts and when testing everything is running fine. Over the weekend we wanted to keep the server running test it over a longer period of time. The server and scripts ran fine all day on Friday, but sometime late on Saturday, the php-cgi stopped running. There are no errors in the error log (C:\WT-NMP\log). In the configuration (php.ini) I have the following options set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On html_errors = On error_log = "c:/wt-nmp/log/php_error.log" We also have the standard nginx.conf error logs: access_log "c:/wt-nmp/log/nginx_access.log"; error_log "c:/wt-nmp/log/nginx_error.log" warn; So, since the log directory is empty, I am assuming that the running php scripts and general nginx operations are not causing the php-cgi to stop. So my questions are: What else could cause the php-cgi to stop running? Are there any other options for logging that we could turn on that could help us track this down? Are there other log locations that we should be looking at? Thanks!

  Read the article

• A Domain Admin user doesn't have effective Administrative rights on a Domain Computer

  - by rwetzeler

  I am a developer who is setting up a virtual domain environment of testing purposes and am having trouble with the setup. I have created a new DC on a new Forest... call it dev.contoso.com. I have setup a virtual internal network for all machines that are going to be apart of this virtual test environment and have given each machine a static IP address in the 192.169.150.0 subnet. I have added machine1.dev.contoso.com to the domain dev.contoso.com. I have also provisioned a user account (adminuser) in the domain and made that user a member of Domain Admins group. Upon logging into machine1 using my newly created Domain Admin account, I cannot access/run any files on machine1. When I go into the advanced permissions for the c:\ folder and goto properties - Security Tab - Advanced - Effective Permissions and search for the dev\adminuser (mentioned above), I get an error saying: Windows can't calculate the effective permissions for admin user What do I need to do to get Administrative rights on Machine1? I am using Server 2008 R2 for both the AD controller and machine1.

  Read the article

• Cannot print certain colours on Ubuntu with HP Laser Printer

  - by ILMV

  We have a load of machines running Ubuntu in our office, they are either on 8.04 or 9.10. We have a server which connects a HP JetDirect that connects to a HP 3550 Colour Laser printer using CUPS. The problem we are having is we cannot print red, magenta or yellow at 100%, I've got a picture of the Ubuntu test page to demonstrate my problem: This is obviously a pretty big problem as we are constantly receiving documents with these colours and cannot successfully print them off, we cannot just switch the grayscale, our business depends on being able to print colour (seems trivial but we handle lots of artwork). We're using the recommended driver HP Color LaserJet 3550 footmatic/pxljr (recommended), there is another driver in the list labelled HP Color LaserJet 3550 footmatic/hpijs. These are production printers so need to make sure any setting change won't kick is in the nuts. It would appear HPIJS is for HP Inkjets, makes sense I guess. The problem doesn't occur in Windows. RESOLVED I've managed to solve the problem, I did indeed use the HPIJS driver (apparently for inkjets) but it seems to have worked, we're going to roll with it for now to see how we get on with it.

  Read the article

• How to connect to local instance of SQL Server 2008 Express

  - by Billy Logan

  I just installed SQL Server 2008 Express on my windows 7 machine. I previously had 2005 on here and used it just fine with the old SQL Server Management Studio Express. I was able to connect with no problems to my PC-NAME\SQLEXPRESS instance. I uninstalled 2005 and SQL Server Management Studio Express. I then installed SQL Server 2008 Express on my machine and elected to have it install SQL Server Management Studio. Now, when I try to connect to PC-NAME\SQLEXPRESS (with Windows Authentication, like I always did), I get the following message: Cannot connect to PC-NAME\SQLEXPRESS. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 When I went to the help link it mentions, the help page suggests the following: * Make sure that the SQL Server Browser service is started on the server. * Use the SQL Server Surface Area Configuration tool to enable SQL Server to accept remote connections. For more information about the SQL Server Surface Area Configuration Tool, see Surface Area Configuration for Services and Connections. I did try starting the SQL Server Browser, but don't see that the Surface Area Configuration is installed with this express version. I had seen another user with an almost exact same issue that was missing the database engine on install. If that were the case how could i test for that and where would i go to download that install. Thanks in advance, Billy

  Read the article

• SQL Server Express backup/restore error: The Media Family on Device is Incorrectly Formed.

  - by Chris

  Basically, I'm having this issue: http://www.sqlcoffee.com/Troubleshooting047.htm What I'm doing is running a script I found online (http://pastebin.com/3n0ZfybL) to do a full backup, then rar'ing up the file and moving it to my computer. The CRC of the backup file inside the rar is correct on both computers, so there is no problem with data being corrupted when I transfer it. But then I go and try to restore the database on my dev computer here and I get the errors "sql server cannot process this media family" ... "msg 3013". Why is this happening? I'd test out the backup on the server I'm getting it from, but it's a production server. Edit: I was about to say how I wasn't doing anything stupid like trying to restore the database to an earlier version of SQL Server, but apparently I am: From: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) To: Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Feb 9 2007 22:47:07 Copyright (c) 1988-2005 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6001: Service Pack 1) Let me get back to this post after I reinstall this.

  Read the article

• Steps after installing vCenter Server?

  - by goober

  I'm working with: Two new ESX servers that I'm configuring A new Server 2008 R2 machine that I'm using for vCenter. I took the following steps: Installed the Hypervisor on the 2 ESX machines Checked their setup/connectivity (appears to be fine; can ping, etc.) Installed vCenter Server on the Win2k8R2 box. This included the install of a SQL Express database (we're a small shop) FYI, I changed some of the ports (443 -- 8443, 80 --8080, etc.) Installed vCenter Web Client Server on the Win2k8R2 box Problems my vSphere Client on my Desktop fails to connect. Part of this is that it asks me for a username and password, but I don't recall specifying one when I set up the install. I receive the error "vSphere Client could not connect to [machinename]. An unknown connection error occurred. (The request failed because of a connection failure. (Unable to connect to the remote server))" I have also tried to use local machine admin credentials, including the format machinename\localuseracct. I have also tried using my domain credentials which are an admin for that box. I have also checked and the service is running. I also tried to connect via vSphere client locally installed on the server. It translates "localhost" to the correct name but gives the same error. I cannot register the vCenter server from the vCenter Web Client Server. I'm not sure if this is necessary, as they're both on the same machine, but it seems like the logical next step. I also receive a "failed to connect" error in this case as well. FYI, both the vCenter server and the vCenter Web Client Server are installed on the same Win2k8R2 server. What am I missing here? What is the best way to test in this case?

  Read the article

• Debugging Samba/CUPS printer sharing with Windows

  - by mrdrbob

  I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

  Read the article

• wildcard deal with www as a subdomain

  - by Alaa Gamal

  i am using wildcard with apache my APACHE CONFIG: ServerAlias *.staronece1.com DocumentRoot /staronece1/domains my named file $ttl 38400 staronece1.com. IN SOA staronece1.com. email.yahoo.com. ( 1334838782 10800 3600 604800 38400 ) staronece1.com. IN NS staronece1.com. staronece1.com. IN A 95.19.203.21 www.staronece1.com. IN A 95.19.203.21 server.staronece1.com. IN A 95.19.203.21 mail.staronece1.com. IN A 95.19.203.21 ns1.staronece1.com. IN A 95.19.203.21 ns2.staronece1.com. IN A 95.19.203.21 staronece1.com. IN NS ns1.staronece1.com. staronece1.com. IN NS ns2.staronece1.com. staronece1.com. IN MX 10 mail.staronece1.com. * 14400 IN A 95.19.203.21 *.staronece1.com IN A 95.19.203.21 my php test file /staronece1/domains/index.php <?php function getBname(){ $bname=explode(".",$_SERVER['HTTP_HOST'],2); return $bname[0]; } echo 'SubDomain is :'.getBname(); ?> if i go to something.staronece1.com i get this result SubDomain is : something No the problem is if i go to www.staronece1.com i should get empty result, because www is not a sub domain but i get this result SubDomain is : www And if i go to www.something.staronece1.com i get firefox error message ( site not found ) How to fix this problem?? i think the solution is: added record for www in named file Thanks

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Apache no longer starts at Windows boot up

  - by w3d

  I have Apache installed as part of XAMPP - local test server. It is configured as a Windows (XP) Service. Startup type is "Automatic". For a long time now it has always started when Windows boots up, but recently this has stopped happening. I now need to start it manually via the XAMPP Control Panel - at which point it appears to start up perfectly OK. The only recent updates to the machine (that I recall) are Windows Updates - none of which appear to have "known issues" that relate to this. And updates to Google Chrome. Any ideas what could prevent Apache from starting automatically at Windows (XP) boot up? EDIT#1 There are 2 related Errors in my system event log regarding the Service Control Manager: Timeout (30000 milliseconds) waiting for the Apache2.2 service to connect. The Apache2.2 service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. When I manually start the Apache server after boot up there are 2 "information" events stating that it was "sent a start control" and that it "entered the running state". Although I notice it appears to take 19 seconds between the start control being sent and entering a running state - according to the event log. So, maybe 30 seconds during boot up isn't long enough (anymore) for Apache to start??

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• Windows 7 Not Starting and System Repair Not Loading

  - by Mark

  I have a Dell Inspiron 1545 running Windows 7 When turning on my PC I keep receiving a black screen with the option to use System Repair or Start Normally. Both options lead me to the System Repair background except no matter how long I wait the system restore options never show up. Choosing F8 and running all of the options including safe mode encounters the same result above. I tried to to use 2 system recovery disks 32x and 64x I downloaded and both lead to similiar results. When I choose System Repair running from the disk the System Repair Question asking to select a language pops ups but after this no matter how long I wait no other options appear. Next after restarting and selecting F8 (after hitting f12 and running from CD) I choose 'Run From Safe Mode with Command Prompt' I am able to run all of the options from System Restore with differing results: Startup Repair: Choosing this ends up in system repair indefinitely (left running 12 hrs) System Restore: Does Nothing. PC thinks for a second and then stops. When selecting ShutDown I see an error message stating there are no restore points. System Image Recovery: Service Cannot be started in Safe Mode Windows Memory Diagnostic: Runs test but then leads to system repair background which never loads system repair Command Prompt: chkdsk /r -Cannot Lock Current Drive...write protected. chkdsk /f -Cannot Lock Current Drive...write protected. bootcfg - Cannot open Boot.Ini file bootcfg - Ran all 3 (rebuildBcd, FixMbr and Fixboot) but PC still goes to System Repair background with no repair options popping up upon restart (without recovery CD). I'm on the verge of purchasing a boot utility disk for $50 unless there is anything else short of "take it to a computer shop" that somebody can suggest I try.

  Read the article

• SQL Server on Linux

  - by TimothyAWiseman

  For a particular project that is coming up, I am trying to expand my knowledge of Linux, so I am going to set up a Linux system at home. Rather than dual booting, I am thinking about putting SQL Server on a Windows Virtual Machine with Linux as the host at least until this project is over when I will probably switch back to Linux. So, I have a couple of different, but interrelated questions: How well does this work? This is only a test machine at home, so I can easily accept a fair bit of degradation, but if it is going to be a horrible reduction in performance I will dual boot instead. Is there a particular virtual machine manager I should look at to go this route? Since this is my personal machine, price is an issue but I am quite happy to pay a reasonable amount. And finally, given the choice of VMM, is there a particular Linux Distro I should be looking at? [This has been cross posted at Ask.SqlServerCentral.com . I think it may be appropriate at both sites. ]

  Read the article

• How to tackle dell support system? [closed]

  - by Nishant Kumar

  We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

  Read the article

• Best Practical RT, sorting email into queues automatically using procmail

  - by user52095

  I'm trying to get incoming e-mail to automatically go directly into whichever queue/ticket they are related to or create a new one if none exist and the right queue e-mail setup in the web interface is used. I will have too many queues to have two line items within mailgate per queue. A similar issue was discussed here (http://serverfault.com/questions/104779/procmail-pipe-to-program-otherwise-return-error-to-sender), but I thought it best to open a new case instead of tagging on what appeared to be an answer to that person's query. I'm able to send and receive e-mail (via PostFix) to the default rt user and this user successfully accepts all e-mail for the relative domain. I have no idea where the e-mail goes - it's successfully delivered, but it does not update existing tickets (with a Subject line match) and it does not create any new. Here's and example of my ./procmail.log: procmail: [23048] Mon Aug 23 14:26:01 2010 procmail: Assigning "MAILDOMAIN=rt.mydomain.com " procmail: Assigning "RT_MAILGATE=/opt/rt3/bin/rt-mailgate " procmail: Assigning "RT_URL=http://rt.mydomain.com/ " procmail: Assigning "LOGABSTRACT=all " procmail: Skipped " " procmail: Skipped " " procmail: Assigning "LASTFOLDER={ " procmail: Opening "{ " procmail: Acquiring kernel-lock procmail: Notified comsat: "rt@18337:./{ " From [email protected] Mon Aug 23 14:26:01 2010 Subject: RE: [RT.mydomain.com #1] Test Ticket Folder: { 1616 Does the notified comsat portion mean that it notified RT? The contents of my ./procmailrc: #Preliminaries SHELL=/bin/sh #Use the Bourne shell (check your path!) #MAILDIR=${HOME} #First check what your mail directory is! MAILDIR="/var/mail/rt/" LOGFILE="home/rt//procmail.log" LOG="--- Logging ${LOGFILE} for ${LOGNAME}, " VERBOSE=yes MAILDOMAIN="rt.mydomain.com" RT_MAILGATE="/opt/rt3/bin/rt-mailgate" #RT_MAILGATE="/usr/local/bin/rt-mailgate" RT_URL="http://rt.mydomain.com/" LOGABSTRACT=all :0 { # the following line extracts the recipient from Received-headers. # Simply using the To: does not work, as tickets are often created # by sending a CC/BCC to RT TO=`formail -c -xReceived: |grep $MAILDOMAIN |sed -e 's/.*for *<*\(.*\)>* *;.*$/\1/'` QUEUE=`echo $TO| $HOME/get_queue.pl` ACTION=`echo $TO| $HOME/get_action.pl` :0 h b w |/usr/bin/perl $RT_MAILGATE --queue $QUEUE --action $ACTION --url $RT_URL } I know that my get_queue.pl and get_action.pl scripts work, as those have been previously tested. Any help and/or guidance you can give would be greatly appreciated. Nicôle

  Read the article

• Why is /usr/bin/env permission denied to rails server?

  - by Eric Hopkins

  I've just set up rails on an apache server running on Ubuntu, and when I try to go to the root page it gives this error: /usr/bin/env: bash: Permission denied env and all the directories in the path all have permissions 755. I tried setting env to have permissions 777 but still got the same error. Rails is running as "nobody". Why is this happening? I don't know what else to try. In /etc/apache2/sites-available/api.conf: <VirtualHost *:80> ServerName api.thinknation.ca ServerAlias api.thinknation.ca DocumentRoot /var/www/api/public ErrorLog /var/www/logs/error.log CustomLog /var/www/logs/access.log combined RailsSpawnMethod smart <Directory /var/www/api/public> # This relaxes Apache security settings. AllowOverride all # MultiViews must be turned off. Options -MultiViews -Indexes # Uncomment this if you're on Apache >= 2.4: Order allow,deny Allow from all #Require all granted </Directory> </VirtualHost> From config/database.yml in my rails directory (with sensitive user names and passwords omitted): default: &default adapter: mysql2 encoding: utf8 pool: 5 username: root password: socket: /var/run/mysqld/mysqld.sock development: <<: *default database: api_development test: <<: *default database: api_test production: <<: *default url: <%= ENV['DATABASE_URL'] %> database: api username: ------------ password: ------------ Not sure what other details or files are relevant, I will add them if needed.

  Read the article

• vagrant and puppet security for ssl certificates

  - by Sirex

  I'm pretty new to vagrant, would someone who knows more about it (and puppet) be able to explain how vagrant deals with the ssl certs needed when making vagrant testing machines that are processing the same node definition as the real production machines ? I run puppet in master / client mode, and I wish to spin up a vagrant version of my puppet production nodes, primarily to test new puppet code against. If my production machine is, say, sql.domain.com I spin up a vagrant machine of, say, sql.vagrant.domain.com. In the vagrant file I then use the puppet_server provisioner, and give a puppet.puppet_node entry of “sql.domain.com” to it gets the same puppet node definition. On the puppet server I use a regex of something like /*.sql.domain.com/ on that node entry so that both the vagrant machine and the real one get that node entry on the puppet server. Finally, I enable auto-signing for *.vagrant.domain.com in puppet's autosign.conf, so the vagrant machine gets signed. So far, so good... However: If one machine on my network gets rooted, say, unimportant.domain.com, what's to stop the attacker changing the hostname on that machine to sql.vagrant.domain.com, deleting the old puppet ssl cert off of it and then re-run puppet with a given node name of sql.domain.com ? The new ssl cert would be autosigned by puppet, match the node name regex, and then this hacked node would get all the juicy information intended for the sql machine ?! One solution I can think of is to avoid autosigning, and put the known puppet ssl cert for the real production machine into the vagrant shared directory, and then have a vagrant ssh job move it into place. The downside of this is I end up with all my ssl certs for each production machine sitting in one git repo (my vagrant repo) and thereby on each developer's machine – which may or may not be an issue, but it dosen't sound like the right way of doing this. tl;dr: How do other people deal with vagrant & puppet ssl certificates for development or testing clones of production machines ?

  Read the article

< Previous Page | 780 781 782 783 784 785 786 787 788 789 790 791  | Next Page >