Search Results

Search found 20931 results on 838 pages for 'mysql insert'.

Page 794/838 | < Previous Page | 790 791 792 793 794 795 796 797 798 799 800 801  | Next Page >

  • VirtualBox guest responds to ping but all ports closed in nmap

    - by jeremyjjbrown
    I want to setup a test database on a vm for development purposes but I cannot connect to the server via the network. I've got Ubuntu 12.04vm installed on 12.04 host in Virtualbox 4.2.4 set to - Bridged network mode - Promiscuous Allow All When I try to ping the virtual guest from any network client I get the expected result. PING 192.168.1.209 (192.168.1.209) 56(84) bytes of data. 64 bytes from 192.168.1.209: icmp_req=1 ttl=64 time=0.427 ms ... Internet access inside the vm is normal But when I nmap it I get nothin! jeremy@bangkok:~$ nmap -sV -p 1-65535 192.168.1.209 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:39 CST Nmap scan report for jeremy (192.168.1.209) Host is up (0.0032s latency). All 65535 scanned ports on jeremy (192.168.1.209) are closed Service detection performed. Please report any incorrect results at http://nmap.org/submit/ Nmap done: 1 IP address (1 host up) scanned in 0.88 seconds ufw and iptables on VM... jeremy@jeremy:~$ sudo service ufw stop [sudo] password for jeremy: ufw stop/waiting jeremy@jeremy:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have scanned around and have no reason to believe that my router is blocking internal ports. jeremy@bangkok:~$ nmap -v 192.168.1.2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:44 CST Initiating Ping Scan at 18:44 Scanning 192.168.1.2 [2 ports] Completed Ping Scan at 18:44, 0.00s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 18:44 Completed Parallel DNS resolution of 1 host. at 18:44, 0.03s elapsed Initiating Connect Scan at 18:44 Scanning 192.168.1.2 [1000 ports] Discovered open port 445/tcp on 192.168.1.2 Discovered open port 139/tcp on 192.168.1.2 Discovered open port 3306/tcp on 192.168.1.2 Discovered open port 80/tcp on 192.168.1.2 Discovered open port 111/tcp on 192.168.1.2 Discovered open port 53/tcp on 192.168.1.2 Discovered open port 5902/tcp on 192.168.1.2 Discovered open port 8090/tcp on 192.168.1.2 Discovered open port 6881/tcp on 192.168.1.2 Completed Connect Scan at 18:44, 0.02s elapsed (1000 total ports) Nmap scan report for 192.168.1.2 Host is up (0.0017s latency). Not shown: 991 closed ports PORT STATE SERVICE 53/tcp open domain 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 445/tcp open microsoft-ds 3306/tcp open mysql 5902/tcp open vnc-2 6881/tcp open bittorrent-tracker 8090/tcp open unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 0.08 seconds Answer... Turns out all of the ports were open to the network. I installed open ssh and confirmed it. Then I edited my db conf to listen to external IP's and all was well.

    Read the article

  • Apache : Illegal override option FileInfo

    - by Kave
    I have installed a new Ubuntu 12.04 Server and setup Apache and MySQL. I am just trying to replicate what I have in my current server and came across one single problem. - FileInfo Within these two files below: /etc/apache2/sites-available/default-ssl /etc/apache2/sites-available/default I need to add some overrides for the apache server. Original: <Directory /var/www/MySite> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> New: <Directory /var/www/MySite> Options Indexes FollowSymLinks MultiViews AllowOverride FileInfo, Indexes Order allow,deny allow from all </Directory> I have installed the following mods for Apache: sudo apt-get install lamp-server^ -y sudo apt-get install apache2.2-common apache2-utils openssl openssl-blacklist openssl-blacklist-extra -y sudo apt-get install curl libcurl3 libcurl3-dev php5-curl -y sudo apt-get install php5-tidy -y sudo apt-get install php5-gd -y sudo apt-get install php-apc -y sudo apt-get install memcached -y sudo apt-get install php5-memcache -y sudo a2enmod ssl sudo a2enmod rewrite sudo a2enmod headers sudo a2enmod expires sudo a2enmod php5 So When I do a restart with AllowOverride None, its all ok. sudo /etc/init.d/apache2 restart * Restarting web server apache2 ... waiting [OK] But as soon as I change the AllowOverride to FileInfo, Indexes Syntax error on line 11 of /etc/apache2/sites-enabled/000-default: Illegal override option FileInfo, Action 'configtest' failed. The Apache error log may have more information. ...fail! I can't see anything unusual in the error.log [Wed Jun 06 08:23:51 2012] [notice] caught SIGTERM, shutting down [Wed Jun 06 08:23:52 2012] [warn] RSA server certificate CommonName (CN) `mySite.com' does NOT match server name!? [Wed Jun 06 08:23:52 2012] [warn] RSA server certificate CommonName (CN) `mySite.com' does NOT match server name!? [Wed Jun 06 08:23:52 2012] [notice] Apache/2.2.22 (Ubuntu) PHP/5.3.10-1ubuntu3.1 with Suhosin-Patch mod_ssl/2.2.22 OpenSSL/1.0.1 configured -- resuming normal operations I get that warning because its a test server, nonetheless I get the same warning with AllowOverride None and yet it restarts the Apache server correctly. Therefore this warning should be harmless. Have I missed something? Thanks,

    Read the article

  • PHP 5.3.2 + Fcgid 2.3.5 + Apache 2.2.14 + SuExec => Connection reset by peer: mod_fcgid: error reading data from FastCGI server

    - by Zigzag
    I'm trying to use PHP 5.3.2 + Fcgid 2.3.5 + Apache 2.2.14 but I always have the error : "Connection reset by peer: mod_fcgid: error reading data from FastCGI server". And Apache returns an error 500 each time I tried to execute a php page : I have compiled the Apache with this options: ./configure --with-mpm=worker --enable-userdir=shared --enable-actions=shared --enable-alias=shared --enable-auth=shared --enable-so --enable-deflate \ --enable-cache=shared --enable-disk-cache=shared --enable-info=shared --enable-rewrite=shared \ --enable-suexec=shared --with-suexec-caller=www-data --with-suexec-userdir=site --with-suexec-logfile=/usr/local/apache2/logs/suexec.log --with-suexec-docroot=/home Then PHP: ./configure --with-config-file-path=/usr/local/apache2/php --with-apxs2=/usr/local/apache2/bin/apxs --with-mysql --with-zlib --enable-exif --with-gd --enable-cgi Then FCdigd: APXS=/usr/local/apache2/bin/apxs ./configure.apxs The VHOST is: <Directory /home/website_panel/site/> FCGIWrapper /home/website_panel/cgi/php .php ... ErrorLog /home/website_panel/logs/error.log </Directory> cat /home/website_panel/logs/error.log [Sun Mar 07 22:19:41 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:41 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:41 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:41 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:42 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:42 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:43 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:43 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php The Suexec log: root:/usr/local/apache2# cat /var/log/apache2/suexec.log [2010-03-07 22:11:05]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:11:15]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:11:23]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:41]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:41]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:42]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:43]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php root:/usr/local/apache2# cat logs/error_log [Sun Mar 07 22:18:47 2010] [notice] suEXEC mechanism enabled (wrapper: /usr/local/apache2/bin/suexec) [Sun Mar 07 22:18:47 2010] [notice] mod_bw : Memory Allocated 0 bytes (each conf takes 32 bytes) [Sun Mar 07 22:18:47 2010] [notice] mod_bw : Version 0.7 - Initialized [0 Confs] [Sun Mar 07 22:18:47 2010] [notice] Apache/2.2.14 (Unix) mod_fcgid/2.3.5 configured -- resuming normal operations root:/usr/local/apache2# /home/website_panel/cgi/php -v PHP 5.3.2 (cli) (built: Mar 7 2010 16:01:49) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies If someone has got an idea, I want to hear it ^^ Thanks !

    Read the article

  • gmail dkim=neutral (no signature)

    - by Bretticus
    After testing much and retracing my steps, I still cannot get google mail to validate. My mail server is Debian 5.0 with exim Exim version 4.72 #1 built 31-Jul-2010 08:12:17 Copyright (c) University of Cambridge, 1995 - 2007 Berkeley DB: Berkeley DB 4.8.24: (August 14, 2009) Support for: crypteq iconv() IPv6 PAM Perl Expand_dlfunc GnuTLS move_frozen_messages Content_Scanning DKIM Old_Demime Lookups: lsearch wildlsearch nwildlsearch iplsearch cdb dbm dbmnz dnsdb dsearch ldap ldapdn ldapm mysql nis nis0 passwd pgsql sqlite Authenticators: cram_md5 cyrus_sasl dovecot plaintext spa Routers: accept dnslookup ipliteral iplookup manualroute queryprogram redirect Transports: appendfile/maildir/mailstore/mbx autoreply lmtp pipe smtp Fixed never_users: 0 Size of off_t: 8 GnuTLS compile-time version: 2.4.2 GnuTLS runtime version: 2.4.2 Configuration file is /var/lib/exim4/config.autogenerated My remote smtp transport configuration: remote_smtp: debug_print = "T: remote_smtp for $local_part@$domain" driver = smtp helo_data = mailer.mydomain.com dkim_domain = mydomain.com dkim_selector = mailer dkim_private_key = /etc/exim4/dkim/mailer.mydomain.com.key dkim_canon = relaxed .ifdef REMOTE_SMTP_HOSTS_AVOID_TLS hosts_avoid_tls = REMOTE_SMTP_HOSTS_AVOID_TLS .endif .ifdef REMOTE_SMTP_HEADERS_REWRITE headers_rewrite = REMOTE_SMTP_HEADERS_REWRITE .endif .ifdef REMOTE_SMTP_RETURN_PATH return_path = REMOTE_SMTP_RETURN_PATH .endif .ifdef REMOTE_SMTP_HELO_FROM_DNS helo_data=REMOTE_SMTP_HELO_DATA .endif The path to my private key is correct. I see a DKIM header in my messages as they end up in my gmail account: DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=mydomain.com; s=mailer; h=Content-Type:MIME-Version:Message-ID:Date:Subject:Reply-To:To:From; bh=nKgQAFyGv<snip>tg=; b=m84lyYvX6<snip>RBBqmW52m1ce2g=; However, gmail headers always report dkim=neutral (no signature): dkim=neutral (no signature) [email protected] My DNS results: dig +short txt mailer._domainkey.mydomain.com mailer._domainkey. mydomain.com descriptive text "v=DKIM1\; k=rsa\; t=y\; p=LS0tLS1CRUdJ<snip>M0RRRUJBUVV" "BQTRHTkFEQ0J<snip>GdLamdaaG" "JwaFZkai93b3<snip>laSCtCYmdsYlBrWkdqeVExN3gxN" "mpQTzF6OWJDN3hoY21LNFhaR0NjeENMR0FmOWI4Z<snip>tLQo=" Note that the base64 public key is 364 chars long so I had to break up the key using bind9. $ORIGIN _domainkey. mydomain.com. mailer TXT ("v=DKIM1; k=rsa; t=y; p=LS0tLS1CRUdJTiBQVUJM<snip>U0liM0RRRUJBUVV" "BQTRHTkFEQ0JpUUtCZ1<snip>15MGdLamdaaG" "JwaFZkai93b3lDK21MR<snip>YlBrWkdqeVExN3gxN" "mpQTzF6OWJDN3hoY21L<snip>Ci0tLS0tRU5E" "IFBVQkxJQyBLRVktLS0tLQo=") Can anyone point me in the right direction? I would really appreciate it.

    Read the article

  • How to use bzdiff to find difference between 2 bzipped files with diff -I option?

    - by englebip
    I'm trying to do a diff on MySQL dumps (created with mysqldump and piped to bzip2), to see if there are changes between consecutive dumps. The followings are the tails of 2 dumps: tmp1: /*!40101 SET SQL_MODE=@OLD_SQL_MODE */; /*!40014 SET FOREIGN_KEY_CHECKS=@OLD_FOREIGN_KEY_CHECKS */; /*!40014 SET UNIQUE_CHECKS=@OLD_UNIQUE_CHECKS */; /*!40101 SET CHARACTER_SET_CLIENT=@OLD_CHARACTER_SET_CLIENT */; /*!40101 SET CHARACTER_SET_RESULTS=@OLD_CHARACTER_SET_RESULTS */; /*!40101 SET COLLATION_CONNECTION=@OLD_COLLATION_CONNECTION */; /*!40111 SET SQL_NOTES=@OLD_SQL_NOTES */; -- Dump completed on 2011-03-11 1:06:50 tmp2: /*!40101 SET SQL_MODE=@OLD_SQL_MODE */; /*!40014 SET FOREIGN_KEY_CHECKS=@OLD_FOREIGN_KEY_CHECKS */; /*!40014 SET UNIQUE_CHECKS=@OLD_UNIQUE_CHECKS */; /*!40101 SET CHARACTER_SET_CLIENT=@OLD_CHARACTER_SET_CLIENT */; /*!40101 SET CHARACTER_SET_RESULTS=@OLD_CHARACTER_SET_RESULTS */; /*!40101 SET COLLATION_CONNECTION=@OLD_COLLATION_CONNECTION */; /*!40111 SET SQL_NOTES=@OLD_SQL_NOTES */; -- Dump completed on 2011-03-11 0:40:11 When I bzdiff their bzipped version: $ bzdiff tmp?.bz2 10c10 < -- Dump completed on 2011-03-11 1:06:50 --- > -- Dump completed on 2011-03-11 0:40:11 According to the manual of bzdiff, any option passed on to bzdiff is passed on to diff. I therefore looked at the -I option that allows to define a regexp; lines matching it are ignored in the diff. When I then try: $ bzdiff -I'Dump' tmp1.bz2 tmp2.bz2 I get an empty diff. I would like to match as much as possible of the "Dump completed" line, though, but when I then try: $ bzdiff -I'Dump completed' tmp1.bz2 tmp2.bz2 diff: extra operand `/tmp/bzdiff.miCJEvX9E8' diff: Try `diff --help' for more information. Same thing happens for some variations: $ bzdiff '-IDump completed' tmp1.bz2 tmp2.bz2 $ bzdiff '-I"Dump completed"' tmp1.bz2 tmp2.bz2 $ bzdiff -'"IDump completed"' tmp1.bz2 tmp2.bz2 If I diff the un-bzipped files there is no problem: $diff -I'^[-][-] Dump completed on' tmp1 tmp2 gives also an empty diff. bzdiff is a shell script usually placed in /bin/bzdiff. Essentially, it parses the command options and passes them on to diff as follows: OPTIONS= FILES= for ARG do case "$ARG" in -*) OPTIONS="$OPTIONS $ARG";; *) if test -f "$ARG"; then FILES="$FILES $ARG" else echo "${prog}: $ARG not found or not a regular file" exit 1 fi ;; esac done [...] bzip2 -cdfq "$1" | $comp $OPTIONS - "$tmp" I think the problem stems from escaping the spaces in the passing of $OPTIONS to diff, but I couldn't figure out how to get it interpreted correctly. Any ideas? EDIT @DerfK: Good point with the ., I had forgotten about them... I tried the suggestion with the multiple level of quotes, but that is still not recognized: $ bzdiff "-I'\"Dump.completed.on\"'" tmp1.bz2 tmp2.bz2 diff: extra operand `/tmp/bzdiff.Di7RtihGGL'

    Read the article

  • ffmpeg hangs when creating a video

    - by FearUs
    I am trying to insert an audio channel with a video: first of all I extract the audio from the original video for processing: ffmpeg -i lotr.mp4 lotr.wav I then extract all frames for later processing too: ffmpeg -i lotr.mp4 -f image2 %d.jpg When done processing audio and video streams, I try to create the video ffmpeg -f image2 -r 15 -i %d.jpg new.mp4 then merge with the audio: ffmpeg -i new.mp4 -i lotr.wav -map 0:0 -map 1:0 new_w_audio.mp4 Result: CPU activity = 100%, the process hangs and never returns. PS: I even tried it without modifying the images or the audio (so just trying to unpack then repack the video) but still the same output FFmpeg version SVN-r26400, Copyright (c) 2000-2011 the FFmpeg developers built on Jan 18 2011 04:07:05 with gcc 4.4.2 configuration: --enable-gpl --enable-version3 --enable-libgsm --enable-libvorb is --enable-libtheora --enable-libspeex --enable-libmp3lame --enable-libopenjpeg --enable-libschroedinger --enable-libopencore_amrwb --enable-libopencore_amrnb --enable-libvpx --disable-decoder=libvpx --arch=x86 --enable-runtime-cpudetect - -enable-libxvid --enable-libx264 --enable-librtmp --extra-libs='-lrtmp -lpolarss l -lws2_32 -lwinmm' --target-os=mingw32 --enable-avisynth --enable-w32threads -- cross-prefix=i686-mingw32- --cc='ccache i686-mingw32-gcc' --enable-memalign-hack libavutil 50.36. 0 / 50.36. 0 libavcore 0.16. 1 / 0.16. 1 libavcodec 52.108. 0 / 52.108. 0 libavformat 52.93. 0 / 52.93. 0 libavdevice 52. 2. 3 / 52. 2. 3 libavfilter 1.74. 0 / 1.74. 0 libswscale 0.12. 0 / 0.12. 0 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'new.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2mp41 creation_time : 1970-01-01 00:00:00 encoder : Lavf52.93.0 Duration: 00:00:29.66, start: 0.000000, bitrate: 193 kb/s Stream #0.0(und): Video: mpeg4, yuv420p, 200x134 [PAR 1:1 DAR 100:67], 192 k b/s, 15 fps, 15 tbr, 15 tbn, 15 tbc Metadata: creation_time : 1970-01-01 00:00:00 [wav @ 01fed010] max_analyze_duration reached Input #1, wav, from 'lotr.wav': Duration: 00:00:29.90, bitrate: 176 kb/s Stream #1.0: Audio: pcm_s16le, 11025 Hz, 1 channels, s16, 176 kb/s File 'new_w_audio.mp4' already exists. Overwrite ? [y/N] y [buffer @ 01b03820] w:200 h:134 pixfmt:yuv420p Output #0, mp4, to 'new_w_audio.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2mp41 creation_time : 1970-01-01 00:00:00 encoder : Lavf52.93.0 Stream #0.0(und): Video: mpeg4, yuv420p, 200x134 [PAR 1:1 DAR 100:67], q=2-3 1, 200 kb/s, 15 tbn, 15 tbc Metadata: creation_time : 1970-01-01 00:00:00 Stream #0.1: Audio: aac, 11025 Hz, 1 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding

    Read the article

  • Local, Multiple-Blog (ie Dashboard) Blogging Software as Alternative to Blogger [closed]

    - by Synetech inc.
    FOR RE-OPENING: I don’t see how it is “too localized”. Plenty of people like to run their own web-apps instead of relying on third-party services. If that were not true, then WordPress, phpBB, Apache, PHP, etc. would not be available for general use. As for “Internet audience at large”, I must have missed the part where it was a rule that you are only allowed to ask for help for things that applies to everyone else too; I thought you were allowed to ask for help. Besides, if someone knows of software that fulfills the question, then it is relevant to whomever would download it, and so is not only applicable to an “extraordinarily narrow situation”. (Besides, the reason that I was asking was because Google had announced that it was discontinuing FTP support for Blogger and so many people were affected—read NOT TOO LOCALIZED—and were trying to find alternatives.) Hi, I am trying to find software (for Windows, PHP, MySQL/SQLite/flat, free, open-source) to localize all of my software and service so that I can keep my files and host when needed from my own system instead of some remote computer. I’ve already selected things like web, FTP, and db servers. I’ve chosen forum and wiki software, as well as an RCS system. At this point, all I’m still looking for—actually, I still need to choose bug-tracking software, but besides that—is blogging software. I still use Blogger and am trying to find something that I can use to import my Blogger stuff and store on (and publish to) my home system. I have read of various blogging software including WordPress, MovableType, and TextPattern. The problem is that I am trying to find something that is like Blogger (which from what I can tell is not available on Google Code as open-source). What I specifically need is multiple-blog support. That is, multiple blogs ala the Blogger Dashboard, not multiple user accounts (although that is important as well). The closest thing that I have been able to find is using Wordpress categories to simulate multiple blogs, but that’s not really what I want. I want software that I can run locally that has a multi-blog dashboard like Blogger. Any ideas? Thanks a lot!

    Read the article

  • Indirect Postfix bounces create new user directories

    - by hheimbuerger
    I'm running Postfix on my personal server in a data centre. I am not a professional mail hoster and not a Postfix expert, it is just used for a few domains served from that server. IIRC, I mostly followed this howto when setting up Postfix. Mails addressed to one of the domains the server manages are delivered locally (/srv/mail) to be fetched with Dovecot. Mails to other domains require usage of SMTPS. The mailbox configuration is stored in MySQL. The problem I have is that I suddenly found new mailboxes being created on the disk. Let's say I have the domain 'example.com'. Then I would have lots of new directories, e.g. /srv/mail/example.com/abenaackart /srv/mail/example.com/abenaacton etc. There are no entries for these addresses in my database, neither as a mailbox nor as an alias. It's clearly spam from auto-generated names. Most of them start with 'a', a few with 'b' and a couple of random ones with other letters. At first I was afraid of an attack, but all security restrictions seem to work. If I try to send mail to these addresses, I get an "Recipient address rejected: User unknown in virtual mailbox table" during the 'RCPT TO' stage. So I looked into the mails stored in these mailboxes. Turns out that all of them are bounces. It seems like all of them were sent from a randomly generated name to an alias that really exists on my system, but pointed to an invalid destination address on another host. So Postfix accepted it, then tried to redirect it to another mail server, which rejected it. This bounced back to my Postfix server, which now took the bounce and stored it locally -- because it seemed to be originating from one of the addresses it manages. Example: My Postfix server handles the example.com domain. [email protected] is configured to redirect to [email protected]. [email protected] has since been deleted from the Hotmail servers. Spammer sends mail with FROM:[email protected] and TO:[email protected]. My Postfix server accepts the mail and tries to hand it off to hotmail.com. hotmail.com sends a bounce back. My Postfix server accepts the bounce and delivers it to /srv/mail/example.com/bob. The last step is what I don't want. I'm not quite sure what it should do instead, but creating hundreds of new mailboxes on my disk is not what I want... Any ideas how to get rid of this behaviour? I'll happily post parts of my configuration, but I'm not really sure where to start debugging the problem at this point.

    Read the article

  • IP failover with 2 nodes on different subnet: cannot ping virtual IP from second node?

    - by quanta
    I'm going to setup redundant failover Redmine: another instance was installed on the second server without problem MySQL (running on the same machine with Redmine) was configured as master-master replication Because they are in different subnet (192.168.3.x and 192.168.6.x), it seems that VIPArip is the only choice. /etc/ha.d/ha.cf on node1 logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth1 node2.ip keepalive 1 node node1 node node2 crm respawn /etc/ha.d/ha.cf on node2: logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth0 node1.ip keepalive 1 node node1 node node2 crm respawn crm configure show: node $id="6c27077e-d718-4c82-b307-7dccaa027a72" node1 node $id="740d0726-e91d-40ed-9dc0-2368214a1f56" node2 primitive VIPArip ocf:heartbeat:VIPArip \ params ip="192.168.6.8" nic="lo:0" \ op start interval="0" timeout="20s" \ op monitor interval="5s" timeout="20s" depth="0" \ op stop interval="0" timeout="20s" \ meta is-managed="true" property $id="cib-bootstrap-options" \ stonith-enabled="false" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="Heartbeat" \ last-lrm-refresh="1338870303" crm_mon -1: ============ Last updated: Tue Jun 5 18:36:42 2012 Stack: Heartbeat Current DC: node2 (740d0726-e91d-40ed-9dc0-2368214a1f56) - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, unknown expected votes 1 Resources configured. ============ Online: [ node1 node2 ] VIPArip (ocf::heartbeat:VIPArip): Started node1 ip addr show lo: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet 192.168.6.8/32 scope global lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I can ping 192.168.6.8 from node1 (192.168.3.x): # ping -c 4 192.168.6.8 PING 192.168.6.8 (192.168.6.8) 56(84) bytes of data. 64 bytes from 192.168.6.8: icmp_seq=1 ttl=64 time=0.062 ms 64 bytes from 192.168.6.8: icmp_seq=2 ttl=64 time=0.046 ms 64 bytes from 192.168.6.8: icmp_seq=3 ttl=64 time=0.059 ms 64 bytes from 192.168.6.8: icmp_seq=4 ttl=64 time=0.071 ms --- 192.168.6.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.046/0.059/0.071/0.011 ms but cannot ping virtual IP from node2 (192.168.6.x) and outside. Did I miss something? PS: you probably want to set IP2UTIL=/sbin/ip in the /usr/lib/ocf/resource.d/heartbeat/VIPArip resource agent script if you get something like this: Jun 5 11:08:10 node1 lrmd: [19832]: info: RA output: (VIPArip:stop:stderr) 2012/06/05_11:08:10 ERROR: Invalid OCF_RESK EY_ip [192.168.6.8] http://www.clusterlabs.org/wiki/Debugging_Resource_Failures Reply to @DukeLion: Which router receives RIP updates? When I start the VIPArip resource, ripd was run with below configuration file (on node1): /var/run/resource-agents/VIPArip-ripd.conf: hostname ripd password zebra debug rip events debug rip packet debug rip zebra log file /var/log/quagga/quagga.log router rip !nic_tag no passive-interface lo:0 network lo:0 distribute-list private out lo:0 distribute-list private in lo:0 !metric_tag redistribute connected metric 3 !ip_tag access-list private permit 192.168.6.8/32 access-list private deny any

    Read the article

  • Why is 50.22.53.71 hitting my localhost node.js in an attempt to find a php setup

    - by laggingreflex
    I just created a new app using angular-fullstack yeoman generator, edited it a bit to my liking, and ran it with grunt on my localhost, and immediately upon starting up I get this flood of requests to paths that I haven't even defined. Is this a hacking attempt? And if so, how does the hacker (human or bot) immediately know where my server is and when it came online? Note that I haven't made anything online, it's just a localhost setup and I'm merely connected to the internet. (Although my router does allow 80 port incoming.) Whois shows that the IP address belongs to a SoftLayer Technologies. Never heard of it. Express server listening on 80, in development mode GET / [200] | 127.0.0.1 (Chrome 31.0.1650) GET /w00tw00t.at.blackhats.romanian.anti-sec:) [404] | 50.22.53.71 (Other) GET /scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/pma/scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /db/scripts/setup.php [404] | 50.22.53.71 (Other) GET /dbadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /myadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /mysql/scripts/setup.php [404] | 50.22.53.71 (Other) GET /mysqladmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /typo3/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin1/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin2/scripts/setup.php [404] | 50.22.53.71 (Other) GET /pma/scripts/setup.php [404] | 50.22.53.71 (Other) GET /web/phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /xampp/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /web/scripts/setup.php [404] | 50.22.53.71 (Other) GET /php-my-admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /websql/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2/scripts/setup.php [404] | 50.22.53.71 (Other) GET /php-my-admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2.5.5/index.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2.5.5-pl1/index.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/ [404] | 50.22.53.71 (Other) GET /phpmyadmin/ [404] | 50.22.53.71 (Other) GET /mysqladmin/ [404] | 50.22.53.71 (Other)

    Read the article

  • PHP 5.3.2 + Fcgid 2.3.5 + Apache 2.2.14 + SuExec => Connection reset by peer: mod_fcgid: error readi

    - by Zigzag
    Hi, I'm trying to use PHP 5.3.2 + Fcgid 2.3.5 + Apache 2.2.14 but I always have the error : "Connection reset by peer: mod_fcgid: error reading data from FastCGI server". And Apache returns an error 500 each time I tried to execute a php page : I have compiled the Apache with this options: ./configure --with-mpm=worker --enable-userdir=shared --enable-actions=shared --enable-alias=shared --enable-auth=shared --enable-so --enable-deflate \ --enable-cache=shared --enable-disk-cache=shared --enable-info=shared --enable-rewrite=shared \ --enable-suexec=shared --with-suexec-caller=www-data --with-suexec-userdir=site --with-suexec-logfile=/usr/local/apache2/logs/suexec.log --with-suexec-docroot=/home Then PHP: ./configure --with-config-file-path=/usr/local/apache2/php --with-apxs2=/usr/local/apache2/bin/apxs --with-mysql --with-zlib --enable-exif --with-gd --enable-cgi Then FCdigd: APXS=/usr/local/apache2/bin/apxs ./configure.apxs The VHOST is: <Directory /home/website_panel/site/> FCGIWrapper /home/website_panel/cgi/php .php ... ErrorLog /home/website_panel/logs/error.log </Directory> cat /home/website_panel/logs/error.log [Sun Mar 07 22:19:41 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:41 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:41 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:41 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:42 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:42 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php [Sun Mar 07 22:19:43 2010] [warn] [client xx.xx.xx.xx] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Sun Mar 07 22:19:43 2010] [error] [client xx.xx.xx.xx] Premature end of script headers: test.php The Suexec log: root:/usr/local/apache2# cat /var/log/apache2/suexec.log [2010-03-07 22:11:05]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:11:15]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:11:23]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:41]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:41]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:42]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php [2010-03-07 22:19:43]: uid: (1001/website_panel) gid: (1001/website_panel) cmd: php root:/usr/local/apache2# cat logs/error_log [Sun Mar 07 22:18:47 2010] [notice] suEXEC mechanism enabled (wrapper: /usr/local/apache2/bin/suexec) [Sun Mar 07 22:18:47 2010] [notice] mod_bw : Memory Allocated 0 bytes (each conf takes 32 bytes) [Sun Mar 07 22:18:47 2010] [notice] mod_bw : Version 0.7 - Initialized [0 Confs] [Sun Mar 07 22:18:47 2010] [notice] Apache/2.2.14 (Unix) mod_fcgid/2.3.5 configured -- resuming normal operations root:/usr/local/apache2# /home/website_panel/cgi/php -v PHP 5.3.2 (cli) (built: Mar 7 2010 16:01:49) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies If someone has got an idea, I want to hear it ^^ Thanks !

    Read the article

  • Django + gunicorn + virtualenv + Supervisord issue

    - by Florian Le Goff
    Dear all, I have a strange issue with my virtualenv + gunicorn setup, only when gunicorn is launched via supervisord. I do realize that it may very well be an issue with my supervisord and I would appreciate any feedback on a better place to ask for help... In a nutshell : when I run gunicorn from my user shell, inside my virtualenv, everything is working flawlessly. I'm able to access all the views of my Django project. When gunicorn is launched by supervisord at the system startup, everything is OK. But, if I have to kill the gunicorn_django processes, or if I perform a supervisord restart, once that gunicorn_django has relaunched, every request is answered with a weird Traceback : (...) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/__init__.py", line 77, in connection = connections[DEFAULT_DB_ALIAS] File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 50, in load_backend raise ImproperlyConfigured(error_msg) TemplateSyntaxError: Caught ImproperlyConfigured while rendering: 'django.db.backends.postgresql_psycopg2' isn't an available database backend. Try using django.db.backends.XXX, where XXX is one of: 'dummy', 'mysql', 'oracle', 'postgresql', 'postgresql_psycopg2', 'sqlite3' Error was: cannot import name utils Full stack available here : http://pastebin.com/BJ5tNQ2N I'm running... Ubuntu/maverick (up-to-date) Python = 2.6.6 virtualenv = 1.5.1 gunicorn = 0.12.0 Django = 1.2.5 psycopg2 = '2.4-beta2 (dt dec pq3 ext)' gunicorn configuration : backlog = 2048 bind = "127.0.0.1:8000" pidfile = "/tmp/gunicorn-hc.pid" daemon = True debug = True workers = 3 logfile = "/home/hc/prod/log/gunicorn.log" loglevel = "info" supervisord configuration : [program:gunicorn] directory=/home/hc/prod/hc command=/home/hc/prod/venv/bin/gunicorn_django -c /home/hc/prod/hc/gunicorn.conf.py user=hc umask=022 autostart=True autorestart=True redirect_stderr=True Any advice ? I've been stuck on this one for quite a while. It seems like some weird memory limit, as I'm not enforcing anything special : $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Thank you.

    Read the article

  • Bladecenter-E Power Module fault

    - by Lihnjo
    We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

    Read the article

  • my multi boot can't boot to XP 'resumeobject' is missing

    - by GwenKillerby
    In my multi boot set up, booting to vista and 7 goes fine, but when I try to boot to XP, i get an error Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: 1. Insert your Windows installation disc and restart your computer. 2. Choose your language settings, and then click "Next." 3. Click "Repair your computer." If you do not have this disc, contact your system administrator or computer manufacturer for assistance. File: \NTLDR Status: 0xc000000e Info: The selected entry could not be loaded because the application is missing or corrupt. See below. Clearly the resumeobject seems to be missing in the XP entry ("Real Mode Boot sector"), only I don't know how to restore it. Vista is on **C:**, Win7 is on **F:** (as is the bootmgr ??? ) and WinXP is on **E:** What I've tried: [1] I've used about 5 windows discs, that is the Recovery Consoles from real XP install CD's and 3 virtual Recovery Consoles. All failed. The real CD's work ONE time, but won't let me finish, I only got as far as [b]fixboot E:[/b] Then they shut the laptop down, I kid you not. On a next startup, all 5 CD's ask me for some Admin password that I've never added! [2] I have VisualBCD and EasyBCD, but the most obvious things I tried there didn't solve the problem. So know I don't exactly know what to do with them. [3] I CAN boot into XP with the FIX NTLDR workaround of http://milescomer.com/tinyempire.com/notes/ntldrismissing.htm, but it doesn't fix it permanently QUESTION: How do I fix it permanently? bcdedit /enum output: Windows Boot Manager -------------------- identifier {bootmgr} device partition=F: path \bootmgr description Windows Boot Manager locale en-US default {current} displayorder {current} {812e27a9-27b7-11e4-8fb4-dfa8174ae8dc} {812e27ac-27b7-11e4-8fb4-dfa8174ae8dc} timeout 30 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Vista locale nl-NL osdevice partition=C: systemroot \Windows resumeobject {73d8b5bc-2764-11e4-b181-806e6f6e6963} Windows Boot Loader ------------------- identifier {812e27a9-27b7-11e4-8fb4-dfa8174ae8dc} device partition=F: path \Windows\system32\winload.exe description Daisy Etta locale en-US osdevice partition=F: systemroot \Windows resumeobject {b8c234a4-27b0-11e4-b8b3-806e6f6e6963} Real-mode Boot Sector --------------------- identifier {812e27ac-27b7-11e4-8fb4-dfa8174ae8dc} device partition=E: path \NTLDR description XP Thank you.

    Read the article

  • Cliq Wireless questions

    - by Nathan Adams
    Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

    Read the article

  • XP OEM licensing when reinstalling Windows XP

    - by mindas
    My wife has managed to buy a Dell laptop she was using at her ex-employer that just went bust. The problem with it is the OS (Windows XP) which takes ages to boot and is generally disproportionally slow to the hardware of the machine. So my aim is to sacrifice a day and reinstall it. The problem I am slightly worried about is the licensing/registration/activation hell. Apart from the sticker (with WinXP license key), the laptop has no other paperwork proving this license is legitimate. I believe this was originally an OEM license. Unfortunately, I don't have the the installation CD. This computer also has MS Office installed (which I would like to retain) but it none of MS Office apps would launch due to some obscure error complaining about lack of free disk space (which computer has plenty of). I have absolutely no clue what kind of license this MS Office was. And because the company has gone into the administration, there is no way of getting this information nor installable media. I believe that by buying the hardware I have also acquired the software which I can use as I see fit. Correct me if I'm wrong. Above said, my question would be: What is the easiest way of reinstalling the XP? By easiest I mean avoiding spending my time to prove Microsoft support I've got the right to use the software (insert your computer says noooo joke here) but still being able to get to fresh virgin activated legal state of the XP. I used to work as a sysadmin many years ago so I am not afraid of any technical difficulties. The same question applies to MS Office. I imagine the process would consist of backing up all the data, pulling some bits from the registry and using that on the fresh install. As for reinstall I'd expect to use some sort of OEM Windows repair CD from Dell, right? Are those freely available? My other box (HP) has such a thing and it can't be used on any other brand. I'm sure somebody had to go through this licensing hell and could share his/her tips. Thanks in advance.

    Read the article

  • Dual booting Windows 7 & 8.1, using the Windows 8 Startup Options Menu, when Windows 8.1 is already installed and you want to add Windows 7

    - by Josh
    There are many excellent guides out there that explain how to dual-boot Windows 7 & 8. However, they are written for people starting with a Windows 7 installation and add a Windows 8 installation to separate partition. From what I'm reading, following this procedure will result in Windows 8 installing and configuring the Startup Options Menu with an option to boot Windows 7 & 8. However, in my situation I have a Windows 8.1 machine that I want to install Windows 7 on, and enable dual-boot, where I can use the Startup Options Menu to select the OS to boot. I haven't been able to determine how to do this. From everything I've been able to find, it looks like if I install Windows 7, it is going to take over the boot loader process, and I won't have access to the Windows 8 "Startup Options Menu." This answer suggests I boot to VHD, but notes a drawback: You can't do this if the C:\drive is encrypted using ANY encryption shceme. Be that BitLocker or 3rd party. The location of the .VHD file you are booting to must reside on an unencrypted volume. Well, that's a bummer, because that's exactly what I wanted to do--I wanted my Windows 7 partition to be encrypted, and my Windows 8 partition to also be encrypted. The idea being that when OS was booted, it was completely locked out from accessing data on the other OS's partition. At this point, I'm thinking my only option is to install Windows 7, and then re-install Windows 8, which will give me the dual-boot option... am I right? Or is there a way to make this work. I'm thinking that I would need to figure out a process like this: Configure the Windows Startup Options Menu with a "blank" entry for Windows 7, pointing to an empty partition Insert the Windows 7 installation media, install Windows 7, and somehow restrict it to that partition (i.e., prevent it from "taking over" from the Startup Options Menu" Is this possible, and if so, how can I accomplish this? My concern is that if I simply install Windows 7 to a separate partition, Windows 7 will take over the entire boot process and I won't be able to get to my Windows 8 installation any more.

    Read the article

  • NTPD issue - syncs then slowly loses ground

    - by ethrbunny
    RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

    Read the article

  • IIS URL Rewrite - Redirect any HTTPS traffic to sub-domain

    - by uniquelau
    We have an interesting hosting environment that dictates all secure traffic must travel over a specific sub domain. E.g. http://secure.domain.com/my-page I'd like to handle this switch using URL Rewrite, i.e. at server level, rather than application level. My cases are: https://secure.domain.com/page = NO CHANGE, remains the same https://domain.com/page = sub-domain inserted, https://secure.domain.com/page https://www.domain.com/page = remove 'www', insert sub-domain In my mind the logic is: INPUT = Full Url = http://www.domain.com/page If INPUT contains HTTPS Then check Full URL, does it contain 'secure'? If YES do nothing, if no add 'secure' If INPUT contains 'www' remove 'www' The certificate is not a wild card (e.g. top level domain) and is issues to: https://secure.domain.com/ The website could also be hosted in a staging environment. E.g. https://secure.environment.domain.com/ I do not have control over 'environment' or 'domain' or the 'tld'. Laurence - Update 1, 19th August So as mentioned below, the trick here is to avoid a redirect loop that could drive anyone well loopy. This is what I propose: One rule to force certain traffic to the secure domain: <rule name="Force 'Umbraco' to secure" stopProcessing="true"> <conditions logicalGrouping="MatchAll"> <add input="{REQUEST_URI}" pattern="^/umbraco/(.+)$" ignoreCase="true" /> <add input="{HTTP_HOST}" negate="true" pattern="^secure\.(.+)$" /> </conditions> <action type="Redirect" url="https://secure.{HTTP_HOST}/{R:0}" redirectType="Permanent" /> </rule> Another rule, that then removes the secure domain, expect for traffic on the secure domain. <rule name="Remove secure, expect for Umbraco" stopProcessing="true"> <match url="(.*)" ignoreCase="true" /> <conditions logicalGrouping="MatchAll"> <add input="{HTTP_HOST}" pattern="^secure\.(.+)$" /> <add input="{REQUEST_URI}" negate="true" pattern="^/umbraco/(.+)$" ignoreCase="true" /> </conditions> <!-- Set Domain to match environment --> <action type="Redirect" url="http://staging.domain.com/{R:0}" appendQueryString="true" redirectType="Permanent" /> </rule> This works for a single directory or group of files, however I've been unable to add additional logic into those two rules. For example you might have 3 folders that need to be secure, I tried adding these as Negate records, but then no redirection happens at all. Hmmm! L

    Read the article

  • XP OEM licensing when reinstalling Windows XP

    - by mindas
    My wife has managed to buy a Dell laptop she was using at her ex-employer that just went bust. The problem with it is the OS (Windows XP) which takes ages to boot and is generally disproportionally slow to the hardware of the machine. So my aim is to sacrifice a day and reinstall it. The problem I am slightly worried about is the licensing/registration/activation hell. Apart from the sticker (with WinXP license key), the laptop has no other paperwork proving this license is legitimate. I believe this was originally an OEM license. Unfortunately, I don't have the the installation CD. This computer also has MS Office installed (which I would like to retain) but it none of MS Office apps would launch due to some obscure error complaining about lack of free disk space (which computer has plenty of). I have absolutely no clue what kind of license this MS Office was. And because the company has gone into the administration, there is no way of getting this information nor installable media. I believe that by buying the hardware I have also acquired the software which I can use as I see fit. Correct me if I'm wrong. Above said, my question would be: What is the easiest way of reinstalling the XP? By easiest I mean avoiding spending my time to prove Microsoft support I've got the right to use the software (insert your computer says noooo joke here) but still being able to get to fresh virgin activated legal state of the XP. I used to work as a sysadmin many years ago so I am not afraid of any technical difficulties. The same question applies to MS Office. I imagine the process would consist of backing up all the data, pulling some bits from the registry and using that on the fresh install. As for reinstall I'd expect to use some sort of OEM Windows repair CD from Dell, right? Are those freely available? My other box (HP) has such a thing and it can't be used on any other brand. I'm sure somebody had to go through this licensing hell and could share his/her tips. Thanks in advance.

    Read the article

  • Varnish + Plesk : vhost broken

    - by Raphaël
    I have an e-commerce site with 300,000 products and 20,000 categories. It is slow and currently in production. I decided to install Varnish to speed up. The trouble is that during installation, I got a Guru Meditation. Since the site is in production, I am not allowed to leave this error more than a second, thinking to have made an enormous stupidity. I followed the following tutorial: http://www.euperia.com/linux/setting-up-varnish-with-apache-tutorial I'm sure I followed all without error. I say that there may be a specific configuration with plesk. Has anyone already installed Varnish on a ubuntu 11.04 server with plesk 10? Does anyone have a better resource? I know it is "very vague" as an error, but maybe some of you have had this problem. edit 24/11/2011 I continued to work on Varnish + Plesk ... but it still does not work. 1) I changed the port for apache in plesk General # mysql -uadmin -p`cat /etc/psa/.psa.shadow` -D psa -e'replace into misc (param, val) values ("http_port", 8008)' 1.1) I rebuild the server conf # /usr/local/psa/admin/bin/httpdmng --reconfigure-all 2) I changed the apache conf files (if those were not taking full plesk top) vim /etc/apache2/ports.conf NameVirtualHost *:8008 Listen 8008 2.1) I do the same with /etc/apache2/sites-enables/000-default 3) I changed the port of my vhost (a single server) vim /var/www/vhosts/MYDOMAIN.COM/conf/XXXXXXXXX.http.include Replace the port 80 by this I want. Rebuild the vhost conf /usr/local/psa/admin/sbin/websrvmng --reconfigure-vhost --vhost-name=<domain_name> with without www (See my issue in serverfault: Edit vhost port in plesk 10.3 ) 4) I installed varnish by following this tutorial : http://www.euperia.com/linux/setting-up-varnish-with-apache-tutorial 5) I restart apache 2 + varnish service apache2 restart service varnish restart When I go to my site, I come across a page of apache It works! This is the default web page for this server. The web server software is running but no content has been added, yet. Can somebody help me ? This means that my vhost does not point to the right place. Why? What to do? How?

    Read the article

  • Why can't I use SSL certs imported via Server Admin in a custom Apache install?

    - by morgant
    I've got a couple of Mac OS X 10.6.8 Server web servers that run a custom AMP255 (Apache 2.x, MySQL 5.x, and PHP 5.x) stack installed using MacPorts. We've got a lot of Mac OS X Server servers and generally install SSL certs via Server Admin and they "just work" in the built-in services, however, these web servers have always had SSL certs installed in a non-standard location and used only for Apache. Long story short, we're trying to standardize this part of our administration and install certs via Server Admin, but have run into the following issue: when the certs are installed via Server Admin and referenced in our Apache conf files, Apache then prompts for a password upon trying to start. It does not seem to be any password we know, certainly not the admin or keychain passwords! We've added the _www user to the certusers (mainly just to ensure they have the proper access to the private key in /etc/certificates/). So, with the custom installed certs we have the following files (basically just pasted in from the company we purchase our certs from): -rw-r--r-- 1 root admin 1395 Apr 10 11:22 *.domain.tld.ca -rw-r--r-- 1 root admin 1656 Apr 10 11:21 *.domain.tld.cert -rw-r--r-- 1 root admin 1680 Apr 10 11:22 *.domain.tld.key And the following in the VirtualHost in /opt/local/apache2/conf/extra/httpd-ssl.conf: SSLCertificateFile /path/to/certs/*.domain.tld.cert SSLCertificateKeyFile /path/to/certs/*.domain.tld.key SSLCACertificateFile /path/to/certs/*.domain.tld.ca This setup functions normally. If we use the certs installed via Server Admin, which both Server Admin & Keychain Assistant show as valid, they're installed in /etc/certificates/ as follows: -rw-r--r-- 1 root wheel 1655 Apr 9 13:44 *.domain.tld.SOMELONGHASH.cert.pem -rw-r--r-- 1 root wheel 4266 Apr 9 13:44 *.domain.tld.SOMELONGHASH.chain.pem -rw-r----- 1 root certusers 3406 Apr 9 13:44 *.domain.tld.SOMELONGHASH.concat.pem -rw-r----- 1 root certusers 1751 Apr 9 13:44 *.domain.tld.SOMELONGHASH.key.pem And if we replace the aforementioned lines in our httpd-ssl.conf with the following: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCertificateChainFile /etc/certificates/*.domain.tld.SOMELONGHASH.chain.pem This prompts for the unknown password. I have also tried httpd-ssl.conf configured as follows: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCertificateChainFile /etc/certificates/*.domain.tld.SOMELONGHASH.concat.pem And as: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCACertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.chain.pem We've verified that the certificate is configured to allow all applications access it (in Keychain Assistant). A diff of the /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem & *.domain.tld.key files shows the former is encrypted and the latter is not, so we're assuming that Server Admin/Keychain Assistant is encrypting them for some reason. I know I can create an unencrypted key file as follows: sudo openssl rsa -in /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem -out /etc/certificates/*.domain.tld.SOMELONGHASH.key.no_password.pem But, I can't do that without entering the password. I thought maybe I could export an unencrypted copy of the key from Keychain Admin, but I'm not seeing such an option (not to mention that the .pem options are greyed out in all export options). Any assistance would be greatly appreciated.

    Read the article

  • Squid Proxy: url_regex acl is not working?

    - by bharathi
    I am using squid proxy 3.1 in ubuntu machine. I want to allow only urls matching our pattern through our proxy server. I configured acl like below. Acl for dstdomain is working fine. If i access any url besides .zmedia.com , I got proxy connection refused. But the url_regex is not working. What i am trying here is. Allow only request from ".zmedia.com" domain and the request url should be in "/blog" context. # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 ::1 acl urlwhitelist url_regex -i ^http(s)://([a-zA-Z]+).zmedia.com/blog/.*$ acl allowdomain dstdomain .zmedia.com acl Safe_ports port 80 8080 8500 7272 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl SSL_ports port 7272 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager http_access deny !allowdomain http_access allow urlwhitelist http_access allow CONNECT SSL_ports http_access deny CONNECT !SSL_ports # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user #http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 3128 # We recommend you to use at least the following line. hierarchy_stoplist cgi-bin ? # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/spool/squid 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/spool/squid append_domain .zmedia.com # Add any of your own refresh_pattern entries above these. refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 Please correct me , If i did anything wrong?

    Read the article

  • How to connect to a Virtualbox guest from the host when network cable unplugged

    - by Greg K
    I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

    Read the article

  • Impossible to create/format install window 7 on unpartioned HD

    - by fra pet
    Hi guys i am getting nut reinstalling windows 7 on one of those Acer aspire all-in-one... The original OS(windows professional x64) was not starting, after the initial screen the bios was prompted. So step 1: i tried to access the system partition and reinstall everything but could not get at the point step 2: i set the bios to native ide and i tried to insert my original copy of windows professional and do a clean installation, but it does not allow me to format/create other partion form the installation mask step 3: my BAD, i tried to install ubuntu and i clean the whole hard drive, i was getting an error at some point during installation so i decided to get back to windows step 4: Windows 7 again, at the disk screen of the windows installation i entered into the prompt and played around with DISKPART... -i listed the disk and the HD was disk 0. -i selected disk 0. -i CLEAN disk 0 successfully. -i tried to create a CREATE PARTITION PRIMARY but gave an error cache corrupt and disk not up-to-date (after i try to create a partiton in disk 0 it disappear when i try LIST DISK and i have to restart before he can list DISK 0 again, RESCAN did not worked). -tried CLEAN ALL(2 hours) and succeeded. -try again to create primary partition and failed, same errors -try to install my old copy of windows xP pro and it seems to work, it create a partition, format(only quick worked, slow mode was at 0% after 1 hour so i stop), it start installing and around 90% installation said it could not copy a file and he stop -back on windows 7 again, it says that the hard drive has 490+gb unpartitioned but won't create a partition and format. -i tried again DISKPART as i though i messed up with the MBR when i installed ubuntu, so i did all of the instruction below http://www.sevenforums.com/tutorials/20864-mbr-restore-windows-7-master-boot-record.html http://support.microsoft.com/kb/927392 the errors were: on bootsect: the systne partiton was not found, Data error cyclic redundancy check on bootrec /FixMbr: A device attached to the system is not functioning but did not worked, and still can not partiton/format/install on a blank HD i tried some bootable clean disk tool and start infinite loop on the same errors the bios setting are: sata: native ide. if i put AHCL(or something like that does not load the HD and the DVD). quick start/quite start: disabled. Are there any other option or tools i can try before i try change the HD(That is my last option)? Thanks to everyone.

    Read the article

< Previous Page | 790 791 792 793 794 795 796 797 798 799 800 801  | Next Page >