Search Results

Search found 22688 results on 908 pages for 'framework installation'.

Page 797/908 | < Previous Page | 793 794 795 796 797 798 799 800 801 802 803 804  | Next Page >

• What is the solution to enable Dymo Turbo 400 Label Printer to work on Win 7 / 64-bit?

  - by mdpc

  It's Christmas time and time for printing labels for all those Christmas cards. I've upgraded to Windows 7 64-bit from XP. I've been unsuccessfully attempting to get the connected Dymo 400 Turbo label USB printer to work again. The latest manufacturer drivers have been successfully loaded and installed. The drivers are supposed to work on Windows 7/64-bit. The Win 7 system(s) in question are patched and up-to-date on that score. The Windows Update site responds with a driver when the USB cable is connected to this printer. The printer queue seems to be established correctly. What happens is that I submit a job to the printer (either using the DYMO s/w or not), it delays for a period of time, and then I get the message 'printing error'. Can't seem to locate the appropriate error in the new and improved event log. Several combinations of rebooting, re-installation and power cycling components fail to make the printer work. Sometimes during some type of reset it spits out the last thing to be submitted, but that seems intermittent. I have tried different USB cables and different USB (2.X) ports as well. I have run the Windows 7 troubleshooter it tries to fix the problem but alas it doesn't. Interestingly, trying the USB printer (and its associated manufacturer drivers and s/w) on another Windows 7 64-bit system has the identical failures noticed on the original system. I did not find anything on the manufacturers' site concerning this problem. The printer has no hardware problems or issues.

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• How do I change the default ftp folder in MacOS X 10.6?

  - by Wild_Eep

  I'm running WordPress 2.9.1 from a Mac running 10.6.3. WordPress is installed to the /Library/WebServer/Documents folder. WordPress has a feature called AutoUpdate. Clicking an autoupdate button will download and install updated versions of the WordPress software, or third-party plugin tools. It's a convenient way to keep things up to date. WordPress uses FTP to download the files. I've enabled FTP and set up a user account and opened the requisite ports in my firewall for FTP traffic. This doesn't seem to be enough for my self-hosted installation, though. I'm sure this feature was originally designed for someone who has access to a remote shared webserver, and that it's merely a configuration challenge related to the FTP setup. I feel that if I can adjust the initial directory that the FTP service presents to the AutoUpdate feature, everything else will work properly. So, my question is, how do I adjust what folder is presented when a given user connects to a Mac running 10.6.3 via FTP?

  Read the article

• Full Apache config migration

  - by Victor Rashkov

  I searched alot and didn't find an applicable answer. I have a working LAMP setup on Ubuntu machine and I have to migrate to a new server in a different country. The old server is 11.10, the new server is 12.04LTS. My problem is that I simply can not remember the steps I followed when I configured the current server which is not the basic LAMP install. It is Apache with FastCGI, SuEXEC, a GD library, worker MPM and all sitting on top of a mhddfs system. There are also other configs I've changed and I can not recall what they are. Because of the complexity of the setup, my attempts to migrate to the new server fail. I get permissions errors, cgi problems etc. Therefore my question is : Is there a sane way to simply tar a full backup of the current web server installation, including MySQL, Php amd the apache server with all configs, and then move it to the new machine? I shall be forever thankful on any advise. So far non of thise I found here gave me an answer. Thanks!

  Read the article

• Upgrading only certain packages via the getdeb repo

  - by intuited

  I'm a bit confused about how getdeb.net works now. The last time I got a package from there was a while ago; at that point the procedure was that you would just download a .deb for each package that you wanted to install/upgrade and then install it using dpkg -i. However the inexorable march of progress has lent its trumpets to this system as well, and getdeb installs are now done via their repo, which is registered with apt in /etc/apt/sources.list.d, after you install a single package that makes the changes to the apt database. I've installed that package, and I've discovered that aptitude dist-upgrade now wants to upgrade a lot of packages on my system that weren't ready for upgrades prior to the installation of the getdeb package. If I rename the file /etc/apt/sources.list.d/getdeb.list to something with a different extension, then do aptitude update && aptitude dist-upgrade, it stops wanting to upgrade packages. So I gather that the default behaviour is now to upgrade all packages to the version available at getdeb. This is not particularly appropriate, since these packages are not as well tested as the officially released versions. Is there a config setting somewhere that will prevent upgrading packages to versions from the getdeb repo unless this action is specifically selected? I'd like to be able to pick and choose what packages are upgraded via getdeb.

  Read the article

• Remote Desktop Services Licensing - Does server have to have a RDS role?

  - by transistor1

  I recently set up a "micro" size Windows 2008 Datacenter server on Amazon AWS. My small group needs several concurrent RDS users to be able to access the machine. Without installing the "Remote Desktop Server" role, it allows 2 concurrent connections. I read on MS' website that in order to set up multiple users, we needed to install the RDS role. I did so, but now the application we are trying to share is running much slower than it was before. Prior to the role installation, it was taking about 5 seconds to open; now it is taking a few minutes to open -- without any other users logged on except me. My assumption is that the RDS role may be too much for this micro instance to handle, and currently, changing to another size instance is not an option (it may be possible later if we were to receive enough funding). This leads me to the following questions: 1) Is it a sensible assessment to assume that it is the RDS role is slowing things down, or are there other things that I could look at to speed it up? We are talking about a machine with ~600MB of memory. 2) If I revert back to the pre-RDS role, is there any legitimate way (in terms of purchasing RDS licenses) to get more than 2 concurrent desktops? I did read this, and am not questioning that the answerer is knowlegeable; but someone else may have some other experience. I am also making it clear that we want to do this in a legitimate way. Thanks in advance for any assistance that can be provided! EDIT: if it is helpful in answering the question, the application in question is a Lotus Approach database. Also, I am asking this from a technical perspective: not a legal one. I want to know if it is possible to install valid licenses without the RDS role.

  Read the article

• How to get back the themes feature in Windows XP?

  - by Martín M.

  When I try to set a visual style in Windows XP (the standard Luna, for example), I get one of these two: "Access denied" error. It works, but when I restart the computer, I get the Classic look again, with no errors. Also, the "Windows and icons" dropdown is grayed out in the "Appearance". This is a list of things I have tried, with no results: Making sure "Use visual styles on windows" is checked on System Properties Advanced Performance. Restarting the "Themes" service. It starts cleanly, no errors. Applying these two fixes: Kelly's Corner and tweaks.com. Running sfc /scannow and checking the integrity of uxtheme.dll against a clean installation of XP Restoring the whole \Windows\Resources\Themes directory. Creating a new user. The new user does not seem to suffer this problem. Maybe this is the solution, create a new user and migrating all the data, but it would be a pain, and I would prefer reinstalling the whole thing. I am using Windows XP Professional SP3, with no spyware, no virus, and no other visible malfunctions. How can I fix this?

  Read the article

• How to fix Truecrypt MBR using Command Prompt or Linux live USB?

  - by Michal Stefanow

  I was playing with TrueCrypt and decided to make a fresh installation of Windows 7 from USB stick. Unfortunately Windows 7 installer: "setup was unable to create a new system partition" My entire HDD has been formatted and is visible as 320GB unallocated space, but no fdisk nor Windows 7 installer nor Windows XP installer could help. (Windows XP doesn't even see the HDD, it sees only USB stick and says "not enough space to install") It may be related to Truecrypt and pre-boot authentification, boot loader and/or MBR. As I don't have optical device I could not have created rescue disk. Right now I need a rescue of some kind, supposingly by erasing/fixing MBR using Linux live USB or using Command Promt. Another approach is to click "repair your comuter" menu from Windows 7 installer then click "restore your computer", then click OK upon error and get access to Command Prompt. Yet another another approach is to start computer without Linux USB I receive this: error:unknown filesystem. grub rescue> Any help would be greatly appreciated as my laptop is kind of not fully operational now. UPDATE: This was asked long time ago, ended up formatting everything (eventually it worked using different bootable USB)...

  Read the article

• Euro character messed up during FTP transfer

  - by djechelon

  My customer is using a very outdated ecommerce management system on my hosting service. For that product, no support is being provided anymore by the vendor. Brief explanation: the shop website, that claims to run under LAMP stack, is built by an old Visual Basic Windows application running on MS Access. The user constructs the shop, defines the HTML template, adds products and categories, etc. Then the VB exe builds the PHP pages (one for each template page) and the SQL script to run on MySQL. It also uploads everything via FTP and runs the installation/upgrade script on its own. The problem Browsing the website, many products' descriptions are cut before the euro sign. For example, what was supposed to be "Product price €1000" becomes "Product price" The analysis MySQL contains a cutted description until the € sign, so it's not PHP fault The Access databases contain full description with € sign, so it's not fault of the webmaster writing bad description or eDisplay cutting them The SQL that will run once the site gets uploaded, stored on my local machine before upload, contains the € sign The same script, after being FTPed by eDisplay and opened with nano from SSH, shows the € sign messed up like this: ^À vsftpd log reports (obfuscated for privacy) Sat Dec 15 11:16:57 2012 22 xxx.xxx.128.13 1112727 /srv/www/domains/xxxxxx.it/htdocs/db.sql b _ i r xxxxxxx ftp 0 * c which seems to be a binary transfer (and also a huge security vulnerability because you can download the whole database from unauthenticated HTTP) The eDisplay internal FTP client provides no option for ascii/binary transfer modes [Add] Trying to manually upload the SQL file via SFTP shows messing up euro [Add2] Trying to manually upload using Xftp client with explicit ASCII mode doesn't fix too It looks like the file gets uploaded as binary. Perhaps on the customer's previous host it all worked fine because that was a Windows host. The server It's an Azure virtual machine running openSUSE 12.2 with both vsftpd and openSSH The question Without asking the customer to manually upload files using FileZilla or replacing € with &euro;, because he refuses, what can I do on server side to prevent vsftpd to screw up euro sign?

  Read the article

• How do I disable tablet gestures in windows 8?

  - by ???

  I'm using a Wacom Intuos4 and I have recently upgraded to Windows 8. I don't have a problem when using Photoshop however I occasionally draw on flash based online boards. The problem is, when I drag the pen in a direction repetitively (which is basically all I do when drawing) it's detected as a gesture, sometimes causing Chrome to go to the previous page (left drag) and making me lose the entire thing. Is there a way to disable these "gestures"? I believe this is not something caused by Windows 8 (or Charms) because I run Windows in English although it's not the initial language that Windows was installed in. I changed to English long after the installation. When Windows takes a move as a gesture, a small text pops up next to the cursor informing me about what I have just done and those pop ups are not even in English. I'm sorry for failing to be any more specific here but these gestures could be a feature of either Windows (unlikely), the tablet, Chrome or the computer itself. It's an Acer Aspire and it has one of those little stickers on it that specifies some of the features and one of them reads "Multi-Gesture" (referring to the touchpad, I guess). Could it be that this Multi-Gesture feature somehow decided to expand and apply for my tablet as well? If so, how do I disable it?

  Read the article

• Lenovo System Update Breaks Windows Live

  - by wolfvilleian

  Hey everyone, I've been racking my brain (and fingers from typing) trying to solve this issue to no avail. I have a Lenovo computer and I install their system update tool to install all my missing drivers. However after this tool is installed Windows Live 2011 breaks, it will no longer sign in giving error number 8e5e0247 all the solutions online haven't helped. It appears that a language setting somewhere gets set to en_ms, and I'm en_ca. My computer is running Windows 7 x64. When i try to sign onto messenger it gives an error that (with some research) means your locale or language is not supported, I've searched my computer for any reference to en_ms but find none. Also a few other things seem to have broken, When a UAC box comes up it is no longer able to identify the publisher of anything, and also the indexing service does not work (I'm not sure if the indexing issue is related, but the UAC issue happened right after installation), I had this issue before but I don't remember how I fixed it, I believe it had something to do with environmental variables. When it goes to sign in it gets as far as the "Loading contacts" then stops and goes back to the sign in screen. Has anyone seen this before? Thanks

  Read the article

• Ubuntu 11.04 fresh install - "Input signal out of range" or "Mode not supported..."

  - by Dennis

  I recently installed Ubuntu 11.04 using a CD .iso. Installation went fine. Upon completion I rebooted and after a second or two I got a black screen with the message "Input signal out of range". And there it sits... Read a few things about how this could be related to screen resolution, refresh rate, etc. For the heck of it I tried a different monitor. The result is the same but the message provides some clues - "Mode not supported - H:92.7kHz, V:58.3Hz" (the latter is Hz; not kHz). So my thought is that I should probably be able to use the 11.04 install disc to "Try out Ubuntu", find and edit some file that was created by the install with the correct values. Problem is, I am not too sure what I am supposed to edit. Looked at the xorg.conf file but this is so minimal at this point I am not sure it is where I want to go. By the way, the monitor is an I-Inc ix191a. Anyone have any ideas on how to get around this?

  Read the article

• Take a regular Windows 7 clone with clonezilla (device-to-image)

  - by Mario De Schaepmeester

  I am unexperienced with cloning software and I've decided to use Clonezilla as it seemed best as freeware. I chose device image and left most options standard. I chose expert mode anyway to see what I could configure, and decided to try the lzop algorithm instead of the default one for compression. The rest was left at default. When Clonezilla asked me which partitions to clone (I chose parts to image), I chose the C:\ drive but Windows 7 also creates a 100MB partition on setup for system files (the actual boot partition?). I copied that into the image as well. The reason I didn't choose disk to image is that I also have a data partition that needs to stay intact. Now I'm simply not sure that this is the way to go, should I ever need to restore my disk image. Will Clonezilla know what to do with both partitions and will Windows 7 work perfectly after restoring? Edit: apparantly a similar question has been asked before. The link to the first article in the answer is not relevant to me since it covers a device-to-device clone. It appears the windows installation disk can repair the 100MB partition. As for Clonezilla, it copies "hidden data after the MBR" by default too. I don't know, I feel I'll be allright whether by restoring the partition with Clonezilla or repairing it with the Windows 7 disk.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• Updating ASUS BIOS on Windows 7 64bit

  - by joesavage

  I've recently decided that I want to try and utilize my two graphics cards so that I can have a dual monitor setup. Unfortunately Windows only seems to notice my most recent graphics card installation - and so I've been told that I should look into my BIOS and try to enable two graphics cards. I could not find this setting anywhere in my M2N68-AM Plus v0210 BIOS. After some further research I figured that I should perhaps upgrade my BIOS, so I searched and managed to download the latest version (v1804) as a ROM file. However I am having difficulty figuring out how to install it. I've tried using the Asus EZFlash feature built into my BIOS, but when trying to load up a variety of different ROMs that are for my motherboard/BIOS I get the error: Boot block in file is not valid! I'm not totally sure what I should do to fix this, so I'm looking into other methods of upgrading my BIOS - however I can't really find any solutions that seem to work. Asus Update is for 32-bit only, AFUDOS doesn't appear to work on my Windows 7 64-bit system (I think it's supposed to run in DOS or something - but that just sounds confusing since I know nothing about DOS). Could anybody help me with this?

  Read the article

• What could cause Windows 7 to hang whenever I install something?

  - by Larsenal

  I've had this problem when installing several different programs (iTunes, Adobe Acrobat Reader just to name two). Regardless of what the program is, the install usually gets at least 90% through the process and then just hangs. I don't see anything bad in the event log besides the following (and this didn't occur exactly at the time of install): wuaueng.dll (964) SUS20ClientDataStore: A request to write to the file "C:\Windows\SoftwareDistribution\DataStore\DataStore.edb" at offset 16252928 (0x0000000000f80000) for 32768 (0x00008000) bytes succeeded, but took an abnormally long time (185 seconds) to be serviced by the OS. This problem is likely due to faulty hardware. Please contact your hardware vendor for further assistance diagnosing the problem. I've run check disk and it passed. I've had some problems with BIOS settings in the past with Windows 7, but I'm not sure whether that could be related. Update... I also see this error in the event log: Volume Shadow Copy Service error: Unexpected error querying for the IVssWriterCallback interface. hr = 0x80070005, Access is denied. . This is often caused by incorrect security settings in either the writer or requestor process. Operation: Gathering Writer Data Context: Writer Class Id: {e8132975-6f93-4464-a53e-1050253ae220} Writer Name: System Writer Writer Instance ID: {33493f01-ac1b-4efb-a378-3053ab03100d} One last wrinkle.... I see "Previous versions" of c:\ which look like they correspond to the time of attempted installation.

  Read the article

• IDE compatability with SATA image

  - by Ormis

  We had an old CNC machine's hard-drive fail recently. The hard-drive is an old 1275MB IDE (Seagate) and there were defiantly bad sectors on it. I was able to image the contents of the drive onto a drive in my computer before it became completely unusable (I used DD, replacing all bad sectors w/ 0s). After running a couple chdsks, the SATA drive will boot off of the image. This is great, but there's one problem. The CNC machine old and requires IDE, I've attempted to copy the currently booting image off of the SATA drive and onto IDE drives numerous times in numerous ways and every time I do so the machines return that a boot device cannot be found. Some other information: The file system is fat32, running windows 98 The SATA drive is an 80gb drive I have tried copying the image to three 20gb and two 80gb IDE drives I have checked the jumper on the back of the IDE drives when using them If anyone has any ideas, questions, suggestions, etc. please let me know. P.S. I would just put a fresh install of win98 on the machine if i had the installation media (so that's out of the question). And if it comes to it, this is my last week working here, so I'll leave that to my co-worker. EDIT: Also, I have tried using Clonezilla as well as straight up DD to copy the image to the IDE drives.

  Read the article

• ssh hangs on "Last login" line

  - by Pavel H

  This happened for the first time three days ago - I ssh to the server, authenticate using a password, get the welcome message but it remains hanging on the "Last login:..." line. The command line doesn't show and the server doesn't react to my input. Other services on the server keep working ok (apache, tomcat, database, ..). The box has an out-of-band management using which I was able to restart it. After the restart the ssh worked ok again and I didn't find anything suspicious in the logs. Three days later the same problem occurs on this box again, and newly on yet another server in the cluster - 100% same symptoms. Both servers have about 2 month old installation of Debian Squeeze (6.0.2) and the problem never occurred before despite frequent ssh-ing, so it should not be a problem of settings. We haven't been installing anything new for quite some time now. I also made sure there is enough disk space on both servers. Since it started to happen all of a sudden on two servers at about the same time, I suspect some bug may have been introduced via Debian updates, yet I haven't been able to find anyone with the same problem. Most similar issues I have found: ssh freezes at the "Last Login Line" - in our case everything worked fine until recently, so nothing related to settings should be our problem. Diskspace checked, I couldn't check the memory but I would expect something would be in the logs if the system had been running out of it. Remote Fedora system unresponsive, odd but consistent behavior when trying to log in - problem with high load on the server; unlike in this case, nothing changes even if I wait for 10+ minutes

  Read the article

• Missing Boot Manager in Vista

  - by Selase

  I am in really deep trouble here and would need advice. A message just pop up on my screen and I had to restart my laptop. Upon restarting the Boot Manager got corrupted. I am running Windows Vista 32 bit by the way. I got onto Google with a friend's PC and found two basic ways of fixing it. The first one that requires Windows to automatically fix it using Startup repair ends up with the error message: Startup REpair cannot repair this computer automatically The second option that requires me to rebuild the BCD scans my system and finds the operating system on drive D:\Windows which I believe should be C:. If I hit Y(yes) for the rebuild process to take place I get the message The required system device cannot be found I then try the second option which requires me to recreate the BCD Store. It ends up with an error message that says: The store export operation has failed. The requested system device cannot be found Proceeding from there is meaningless since the system device cannot be found. I somehow believe the device cannot be found because it's identifying the Windows installation on D: instead of C: but how to change that I have no idea. I don't know how it happens to identify an operating system on D: when there's none there. How do I go about fixing the Boot Manager? I have very important files on my system and can't afford to reinstall Windows. I really need to fix this.

  Read the article

• Lost Windows 7 boot after EasyBCD with EFI

  - by drent

  I've got a Lenovo Y580 with a 64GB SSD and a 1TB HDD setup using GPT and setup to boot from (U?)EFI. I was trying to get my Linux Mint installation on the Windows boot manager using EasyBCD (I didn't realise EFI but it wiped my boot partition/loader and I cannot seem to get Windows back (and I still can't get a bootable Linux Mint). Using the System Recovery utility, Startup Repair can't "see" windows (it might be because I'm using a 7 Pro disk to recover Home Premium?). In command prompt, Bootrec tools don't do anything and bootsect can't run because it says that it's for BIOS only and I've booted with EFI. I can see the EFI data on the 200mb SSD partition using diskpart but I don't know how to add Windows back onto whatever bootloader I have/need. At the moment the only options I can see are: Do a fresh install of Windows and hope that the setup remains as fast as the default one (the SSD is some kind of cache for Windows but I can't quite see how it works given that the rest of the SSD is unpartitioned space). This seems like overkill given that Windows was working fine til EasyBCD deleted it. Try forcing BIOS mode and see if that somehow magically fixes things Try converting from GPT to MBR to try and use the bootrec/bootsect tools (and maybe back again) which seems like a really bad idea. Anyone have any ideas?

  Read the article

• Intel HD Graphics vs NVIDIA Quadro FX 380 PCI-E

  - by Michael

  I recently purchased an Acer Veriton which has an i5-650 processor, Windows 7 Pro (64 bit) and Intel HD Graphics listed as the video card. I also purchased a PNY nVIDIA Quadro FX 380 PCI-E card for improved picture and home video viewing and editing. I have already replaced the original 300 wattt power supply to a 430 watt Antec Truepower I had on hand and boosted the RAM to 8 gigs from the original 4. Question 1) Am I getting any improvement in visual quality or system speed with the Quadro or is it a waste of money and I should just save up to buy a bigger video card? This card was on sale for $115. If I am getting improvement then I need to ask another question. Question 2) Instructions for the Quadro installation are as follows... 1--Uninstall the existing VGA driver. -Remove the existing Display Driver via "Add or Remove Porgrams". -Shut down your computer. 2--Remove your Existing Graphics Board (or Disable Integrated 3D Graphics Controller). skipping instructions on how to remove existing graphics board -Systems with integrated (also know as on-board) 3D graphics may require you to disable the integrated 3D graphics system. Consult the owners or vendor manual that came with your PC on how to properly do this. So is the Intel HD Graphics considered a 3D graphics controller? If so should I just contact Acer or can anyone give me instructions? Thanks in advance for any help.

  Read the article

• can't register a soft phone to asterisk11

  - by Tom

  I have a VM (on oracle vbox) running Fedora17. I've installed asterisk 11 on it from sources. I've followed the wiki for installation (https://wiki.asterisk.org/wiki/display/AST/Creating+SIP+Accounts) to the letter. The ip on the VM machine running fedora is 192.168.1.7 and I can ping it from the host machine (Ubuntu 12.04), which is at 192.168.1.2 I've tried registering with ekiga with the following settings: user: [email protected]. Password: verysecretpassword registar: 192.168.1.7 but I'm getting an error "transport fail". Also, while trying to register I'm logged in to the asterisk CLI with verbose level 3 and debug level 4 and nothing appears. some more relevant data: I've added the following code to the end of my sip.conf.sample file: [demo-alice] type=friend host=dynamic secret=verysecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 [demo-bob] type=friend host=dynamic secret=othersecretpassword context=users deny=0.0.0.0/0 permit=192.168.1.0/255.255.255.0 After I changed the sip.conf.sample file, I've created a copy of it and named it sip.conf. then I logged in to the asterisk CLI and typed sip reload. Then I'm trying to register and ekiga client from my host machine at 192.168.1.2 but it doesn't work and nothing appears on the asterisk CLI while in verbose mode level 3. BTW, If there is missing information about my question, please don't close it. comment about what you need to know and I'll edit it in to the question. tnx.

  Read the article

• Grub rescue, unknown file system. Can't boot into Windows 7

  - by Sam J

  So, I'm confused, so I'm also going to use this question to get clarification and fix my computer. So, some background: I had Windows 7 on a 1 TB HDD and decided to partition my hard drive into two ~500 GB, one for Windows 7 and one for Ubuntu or whatever flavour I desired (like a sandbox partition...) I installed Ubuntu but the installation had issues so I decided to uninstall. Note before uninstallation I had to press f12 when I turned on to boot from my primary HDD, then choose what OS I wanted to use. Undesirable, but it worked. Anyway, after I decided to uninstall Ubuntu I went into Windows 7 Start Computer Manage and deleted the EXT4 filesystem (Ubuntu parition) giving me 4xx GB of free space. However when I restarted Windows 7, I am now unable to boot Windows. When I DON'T hit f12, I see a blank screen with a flashing underscore. When I DO hit f12, I choose my primary HDD, and then I get a GRUB error: Unknown filesystem: grub rescue _ Something I'm unclear of: GRUB boots linux partitions, right? What boots Windows? Is GRUB "overwriting" the Windows bootloader? How can I completely get Windows back to normal? (IE, It boots automatically without hitting f12.) Thanks for any help, I'm on a live CD version of Ubuntu right now until I can get back on Windows.

  Read the article

• Can't ssh from CentOS 6.5 to SUSE LINUX 10.1

  - by Pavel Tankov

  We have a quite old installation of SUSE LINUX 10.1 (i586) in the office. The problem shortly: I can successfully ssh to it from machines in the same LAN (192.168.1.0) and not from others (that are in 10.23.0.0). The SuSE has SSH server openssh-4.2p1-18.12. I have ruled out the firewall and hosts.allow and hosts.deny files. When my ssh login attempt fails, here is what the logs say: on the client: $ ssh -vvv 192.168.1.5 OpenSSH_5.3p1, OpenSSL 1.0.1e-fips 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.1.5 [192.168.1.5] port 22. debug1: Connection established. debug1: identity file /home/nbuild/.ssh/identity type -1 debug1: identity file /home/nbuild/.ssh/identity-cert type -1 debug1: identity file /home/nbuild/.ssh/id_rsa type -1 debug1: identity file /home/nbuild/.ssh/id_rsa-cert type -1 debug1: identity file /home/nbuild/.ssh/id_dsa type -1 debug1: identity file /home/nbuild/.ssh/id_dsa-cert type -1 on the server: Aug 21 16:34:25 serverhost sshd[20736]: debug3: fd 4 is not O_NONBLOCK Aug 21 16:34:25 serverhost sshd[20736]: debug1: Forked child 20739. Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: entering fd = 7 config len 403 Aug 21 16:34:25 serverhost sshd[20736]: debug3: ssh_msg_send: type 0 Aug 21 16:34:25 serverhost sshd[20736]: debug3: send_rexec_state: done Aug 21 16:34:25 serverhost sshd[20739]: debug1: rexec start in 4 out 4 newsock 4 pipe 6 sock 7 Aug 21 16:34:25 serverhost sshd[20739]: debug1: inetd sockets after dupping: 3, 3 Aug 21 16:34:25 serverhost sshd[20739]: debug3: Normalising mapped IPv4 in IPv6 address Aug 21 16:34:25 serverhost sshd[20739]: Connection from 10.23.1.11 port 44340 The above log on the server is when I enable DEBUG3 log level. However, with the default log level (INFO), the only thing the server logs is this: Aug 21 16:38:32 serverhost sshd[20749]: Did not receive identification string from 10.23.1.11 Any hints? I feel I've tried everything already.

  Read the article

• debian lenny email server

  - by Dal

  Hi I am a newbie and set up a debian lenny at home and set up the web and email server in the default installation. I followed the instructions for Exim and ran dpkg-reconfigure exim4-config and set it up for mydomainhere.com. I created a one line message file and attempted to test exim by running the command exim [email protected] < msgfile. I also tried using exim4 Exim but i get same error -bash: Exim: command not found. Obviously I am ignorant on how to run exim and test. I also tried to run a php file that sends a test mail and had no success. That script is tested and works fine if I send it from my hosting isp on a different domain. So I know the php script is good. I set up the debian system behind a netgear firewall and uses 192.168.1.x ip . The web server works great and users can visit my site. But I am lack the knowledge on how to get the email working. Appreciate is someone can guide me.

  Read the article

< Previous Page | 793 794 795 796 797 798 799 800 801 802 803 804  | Next Page >