Search Results

Search found 199 results on 8 pages for 'glitch'.

Page 8/8 | < Previous Page | 4 5 6 7 8

Second HDD not seen by Windows 7 on Dell Xps l501x

- by George

I have a Dell XPS Laptop (l501x). I have replaced the original Seagate 500GB hard drive with an SSD Intel 320 120GB when I first purchased it a year ago. It's been working great. The laptop is booting in about 23 seconds, so the SSD is great. I have an Acronis image created that I came back to every three months just to keep everything clean. The SSD is partitioned with one logical drive for my data. So, recently I thought since I am not using my optical drive often enough to swap it out with a HDD caddy and add my seagate 500gb hard drive. I ordered the caddy placed the HDD in it and now load Windows. It just hangs on the screen that should show the Windows logo. I have tried everything that I know and searched it online. I have uninstalled the SATA controller AHCI and let Windows install it. Still will not boot into windows. I wanted to mention that the Seagate 500GB drive was the one that came with my laptop before I switched to the Intel SSD. As you know Intel has this application called Intel Rapid Technology which loads once in a while and shows the second hard drive, but then, when I restart it hangs again and Windows will not load. As soon as I remove the HDD Caddy and restart it loads Windows fine. I also formated the Seagate 500GB HDD in NTFS and still Windows will not load. When I go into the BIOS it shows the Fixed SSD and also "Sata ODD 500GB" instead of the optical drive but it will not boot into Windows when the HDD caddy is present. There is nothing wrong with the caddy. I have another laptop (Asus) and I installed the HDD caddy and Windows 7 loads without any glitch. I don't get it. I have also flashed the BIOS because Dell had a new version (A08). I also wanted to add that I refreshed Disk Management and the Device Manager and the second drive does not display. At this point I think it's a Windows issue so before I reinstall Windows 7 Home Premium from scratch I wanted to see if there was anything I was missing. Any advice would be greatly appreciated.

Read the article
Possible HDD malfunction. Need help in diagnosing

- by Protheus

Today when using my PC as I did for almost 4 years I experienced the following: during opening new tab in Opera browser screen froze. Music (AIMP 3) continued to play for about 5 minutes and then stopped too. I tried Ctrl+Alt+Del, but win7 lock screen didn't appear. Caps\Scroll or Num locks didn't switch diodes on keyboard. I rebooted my PC and saw that BIOS suggests me to enter it's settings or load by default. I chose default. It don't see proper boot device (old faitful "insert proper boot" something). After second reboot it said that there is no ExpressGate installed (which i turned off in BIOS years ago). I went into BIOS setting to turn off ExpressGate and see configs: time was not set off, all hard drives present, temp and O.C. settings are nominal (no O.C.) I've inserted my Win7 install disk to try recovery. It did load awfully long (about few minutes) and didn't see current installation. PC was utilized in 24/7 mode for almost all these years. Hardware configuration: ASUS P5Q WS Core 2 Quad Q9300 (2.5GHz no O.C.) MSI geForce GTX 460 4x2 Gb GeIL EVO 2 (AFAIR) Seagate something 750Gb (4 years as system HDD 24/7) WD 1Tb (for random stuff, 5 y.o.) Hitachi 500Gb (for even more random stuff, 6 y.o.) NEC DVDRW (ALL DISKS ARE SATA) Cooler Master Silent Pro 700W Software: Windows 7 AND Kubuntu on the same drive with GRUB loader. Sorry I can't remember HDDs and can't see them right now, but I think their models aren't relevant anyway. My idea is that due to some system error or hard drive glitch i've wrecked my primary HDD's MBR. Nevertheless I don't exclude the possibility of other failure. May it's be that motherboard or it's SATA controller? Doubt it, because all drives are seen in BIOS and I could load from DVD. Maybe GRUB got bugged somehow, although I don't see how it's possible from Windows. But I did install KUbuntu from Windows (i wasn't myself then), maybe GRUB did write itself in some windows partition and got rewriteen in process? Right now I am at work with my flash drive with me and I need some advice how to fix MBR or to hear if it's not MBR. I'm going to buy new HDD (Hitachi 7k2000) because I think that my current HDD is compromised and it's unsafe to use it as system drive, especially 24/7.

Read the article
SQL SERVER – Signal Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

- by pinaldave

In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Signal Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Signal Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Signal Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the Signalwait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the Signal wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the Signal wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

Read the article
SQL SERVER – Single Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

- by pinaldave

In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Single Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Single Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Single Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the single wait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the single wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the single wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

Read the article
Using the “Settings.settings” functionalities in VB.NET can be tricky…

- by Vincent Grondin

Sometime you’re searching for something forever and when you find it, you realize it was right under your nose. Maybe you were distracted by other things around… or maybe that thing right under your nose was so well hidden that it deserves a blog post… That happened to me a few days ago while using the “Settings.settings” functionalities in my VB.NET application… I thought it was a cool feature and I decided to use it… So there I am adding new settings with “USER” scope and StringCollection as the data type, testing my application and everything works perfectly fine... That was before I decided to modify the “Value” of one of my settings… After changing the value of one of my settings, I start my application again and, to my surprise, my new values aren’t showing! Hmmm… That’s odd… My setting was a pretty long list of strings so I was rather angry at myself for not saving my work after I was done… So I open up the Settings.setting in the designer and click the ellipsis symbol to enter my string collection again, but to my great pleasure (and disbelief) my strings are there!!! Alright, you rock VB.NET! You’ve just save me a bunch of typing time and I’m thinking it’s just a simple Visual Studio glitch… I hit “Save” then “Save All” (just in case) and finally I rebuild everything and fire up my app once again. Huh? Where are my darn strings???????? Ok there’s a bug there… I open up the app.config and my new strings are there!!! Alright, let’s recap… My new strings are in the app.config, they show correctly in the Settings.settings designer UI but they aren’t showing at runtime… Hmmmm? Let’s try something else… Let’s start the application but outside Visual Studio this time… I fire up the exe and BAM! My strings where there! I “alt-tab” and hit “F5” and BOOM, no strings! So it’s a bug in the Visual Studio environment… or could it be a FEATURE? I must admit that I’m a little confused over what’s a bug and what’s a feature in Visual Studio… lol! Finally I found out there’s a “cache” for your Visual Studio located here: C:\Users\<your username>\AppData\Local\Microsoft\<your app name and a very weird temp ID>\<your app version>\user.config When using the “Settings.settings” with a setting of scope “user”, this file is out of sync with your app.config until you manually decide to update it… The button is right there… under your nose… at the top left corner of your screen in the settings designer… See the big “Synchronize” button there? Yep… Now that’s user friendly isn’t it? Oh, and wait until you see what it does when you click it… It prompts you and basically says: “Would you like your settings to start working inside Visual Studio now that you found out that I exist?” and of course the right answer is yes… or rather “OK”… Unfortunately, you have to do this every time you edit a value… On the other hand, adding and removing settings seem to work flawlessly without having to click this magical button… go figure! Oh and I almost forgot… this great “feature” is only available for VB.NET… A project in C# using Settings.settings will work perfectly EVEN when editing values… Here’s a screenshot that shows this important button: Button Using other data types appears to work perfectly well… Maybe it’s simply related to the StringCollection data type? If you are a VB.NET programmer, you should pay attention to this when you plan on using the settings functionalities and your scope is “user” and your data type is StringCollection… Happy coding all!

Read the article
How do I install on an UEFI Asus 1215b netbook?

- by Tarek

I'm trying to install Ubuntu 11.10 on a UEFI netbook Asus 1215b using an USB stick. I created a fat32 efi partition of 100MB, 2GB swap, and 2 ext4 partitions (for root (/ ) and /home, respectively). While installing, Ubuntu switches to CLI and starts running efibootmgr. After a few commands (sadly I don't have a screen grab), it stops displaying text but it's still running judging by the HDD led. Then, there's a weird graphic glitch and the screen turns off (HDD led still indicating activity). Finally, it just stops, but doesn't turn off. Not even a hard reboot works (holding down the power button a few secs). I have to plug the netbook off and remove the battery. After that, it still doesn't boot Ubuntu... Anyway, what can I do? I'm considering following the footsteps here and here. Edit: here is the syslog $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] BUG: unable to handle kernel paging request at 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] IP: [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] PGD 14ecc067 PUD 0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Oops: 0000 [#1] SMP $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CPU 0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Modules linked in: cryptd aes_x86_64 ufs qnx4 hfsplus hfs minix ntfs msdos xfs reiserfs jfs bnep parport_pc rfcomm dm_crypt ppdev bluetooth lp parport joydev eeepc_wmi asus_wmi sparse_keymap uvcvideo videodev v4l2_compat_ioctl32 snd_hda_codec_realtek snd_seq_midi snd_hda_codec_hdmi snd_hda_intel snd_hda_codec arc4 snd_rawmidi snd_hwdep psmouse snd_pcm snd_seq_midi_event ath9k serio_raw sp5100_tco i2c_piix4 k10temp snd_seq mac80211 snd_timer ath9k_common ath9k_hw snd_seq_device ath snd cfg80211 soundcore snd_page_alloc binfmt_misc squashfs overlayfs nls_iso8859_1 nls_cp437 vfat fat dm_raid45 xor dm_mirror dm_region_hash dm_log btrfs zlib_deflate libcrc32c usb_storage uas radeon video ahci libahci ttm drm_kms_helper drm wmi i2c_algo_bit atl1c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Pid: 28432, comm: efibootmgr Not tainted 3.0.0-12-generic #20-Ubuntu ASUSTeK Computer INC. 1215B/1215B $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RIP: 0010:[<ffff880066d44c1f>] [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RSP: 0018:ffff88005e2cbab0 EFLAGS: 00010082 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RAX: 00000000ffe1867c RBX: 0000000000000009 RCX: 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RDX: 0000000000000000 RSI: ffff88005e2cbbea RDI: ffff88005e2cbb40 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RBP: 00000000ffe1867c R08: 0000000000000000 R09: 0000000000000084 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] R10: ffffc9001101ff83 R11: ffffc90011018685 R12: 0000000000000001 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] R13: 0000000000000000 R14: ffffc9001101867c R15: ffff88005e2cbbe1 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] FS: 00007f9cdde13720(0000) GS:ffff880066a00000(0000) knlGS:0000000000000000 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CR2: 00000000ffe1867c CR3: 000000002dace000 CR4: 00000000000006f0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Process efibootmgr (pid: 28432, threadinfo ffff88005e2ca000, task ffff880014f0dc80) $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Stack: $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ffffc90011010000 ffff88005e2cbac8 0000000000010000 ffff880066d4401d $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] 000000000000007c ffff880009e84400 0000000000000090 ffff880066d45738 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ffffc9001101867c ffff880066d4331c 0000000000000009 ffffc9001101867b $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Call Trace: $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815e9efe>] ? _raw_spin_lock+0xe/0x20 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9c2d>] ? open+0x10d/0x1b0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff8116554b>] ? __dentry_open+0x2bb/0x320 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9b20>] ? bin_vma_open+0x70/0x70 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815e9efe>] ? _raw_spin_lock+0xe/0x20 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811849ee>] ? vfsmount_lock_local_unlock+0x1e/0x30 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff8104303b>] ? efi_call5+0x4b/0x80 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81042a7f>] ? virt_efi_set_variable+0x2f/0x40 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff814bb125>] ? efivar_create+0x1e5/0x280 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9d63>] ? write+0x93/0x190 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9de4>] ? write+0x114/0x190 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81167813>] ? vfs_write+0xb3/0x180 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81167b3a>] ? sys_write+0x4a/0x90 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815f22c2>] ? system_call_fastpath+0x16/0x1b $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Code: ec 01 75 f0 41 bc 01 00 00 00 e8 e5 fb ff ff e8 e4 fc ff ff 33 c0 44 0f b7 c0 66 3b c3 73 20 41 0f b7 c0 41 0f b7 d0 03 c5 8b c8 <8a> 00 42 38 04 3a 75 0a 66 45 03 c4 66 44 3b c3 72 e2 33 c0 66 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RIP [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RSP <ffff88005e2cbab0> $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CR2: 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ---[ end trace 493844b002da4787 ]---

Read the article
WPF ClickOnce Bootstrap Dection Failure on One Machine

- by Dexter Morgan

Hello Friend, I've decided to use ClickOnce technology to deploy my new WPF application. By and large, ClickOnce works as advertised but I've hit a minor glitch regarding Bootstrapping and framework detection. Some background: - I'm using the standard Visual Studio-generated publish.htm page as my launch page. - The only prerequisite is the .NET Framework 4.0 Client Profile. - All clients using IE 8. - All clients already have the .NET 4.0 Client Profile installed. ClickOnce works as advertised on the vast majority of machines. The VS-generated JScript correctly detects that the framework is installed and presents the user with a Run button. The app launches just fine. I'm getting odd results on one of the machines, however. On the offending machine, the VS-generated JScript tells the user that the prereqs may not be installed -- or rather, it FAILS to detect that the framework is already installed. The "launch" link successfully launches the application but the Run link points to the bootstrapper setup.exe. Why is it failing to detect the framework on this one machine? It occurred to me that framework detection is largely a matter of examining the useragent string that's submitted by the browser. So, what you see below are two UserAgent strings. The first is from a machine where things are working properly. The second is from the offending machine. THIS ONE WORKS: 2011-01-11 15:14:14 W3SVC1 192.168.0.36 GET /publish.htm - 80 - 72.130.187.100 Mozilla/4.0+(compatible;+MSIE+8.0;+Windows+NT+6.0;+Trident/4.0;+SLCC1;+.NET+CLR+2.0.50727;+Media+Center+PC+5.0;+.NET+CLR+3.5.21022;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+.NET4.0C) 304 0 0 THIS ONE DOESN'T: 2011-01-11 18:49:12 W3SVC1 192.168.0.36 GET /publish.htm - 80 - 76.212.204.169 Mozilla/4.0+(compatible;+MSIE+8.0;+Windows+NT+6.1;+WOW64;+Trident/4.0;+GTB6.6;+SLCC2;+.NET+CLR+2.0.50727;+.NET+CLR+3.5.30729;+.NET+CLR+3.0.30729;+Media+Center+PC+6.0;+.NET4.0C) 200 0 0 The useragent string of both machines clearly states, "hey the .NET 4.0 client profile is installed here" -- yet the second machine seems unable to detect it. I don't know enough about useragent strings to understand why the former works and the latter fails. The only difference as far as I can tell is that the offending machine is running 64bit. But that shouldn't make a difference. Should it? Any ideas? Dexter Morgan

Read the article
Do you use an exception class in your Perl programs? Why or why not?

- by daotoad

I've got a bunch of questions about how people use exceptions in Perl. I've included some background notes on exceptions, skip this if you want, but please take a moment to read the questions and respond to them. Thanks. Background on Perl Exceptions Perl has a very basic built-in exception system that provides a spring-board for more sophisticated usage. For example die "I ate a bug.\n"; throws an exception with a string assigned to $@. You can also throw an object, instead of a string: die BadBug->new('I ate a bug.'); You can even install a signal handler to catch the SIGDIE psuedo-signal. Here's a handler that rethrows exceptions as objects if they aren't already. $SIG{__DIE__} = sub { my $e = shift; $e = ExceptionObject->new( $e ) unless blessed $e; die $e; } This pattern is used in a number of CPAN modules. but perlvar says: Due to an implementation glitch, the $SIG{DIE} hook is called even inside an eval(). Do not use this to rewrite a pending exception in $@ , or as a bizarre substitute for overriding CORE::GLOBAL::die() . This strange action at a distance may be fixed in a future release so that $SIG{DIE} is only called if your program is about to exit, as was the original intent. Any other use is deprecated. So now I wonder if objectifying exceptions in sigdie is evil. The Questions Do you use exception objects? If so, which one and why? If not, why not? If you don't use exception objects, what would entice you to use them? If you do use exception objects, what do you hate about them, and what could be better? Is objectifying exceptions in the DIE handler a bad idea? Where should I objectify my exceptions? In my eval{} wrapper? In a sigdie handler? Are there any papers, articles or other resources on exceptions in general and in Perl that you find useful or enlightening.

Read the article
Windows MAchine Debugging

- by PrettyFlower

I've been learning how to program for Windows for some time now and am getting pretty comfy with COM. I had thought to go over to Linux and do some C++ programming there and I wished to run Rosetta Commons so I installed Fedora. I had tried installing Ubuntu a few months ago and things got messy. I had a glitch, maybe caused by one of the live cd creators, my video card or something I don't know. Who Crashed suggested it was my video card and I had regular messages about ntfs.sys and page file issues. At any rate I just installed Fedora and the same thing is happening again. I would like to think with the twenty five years of doing this that I might finally make some headway into debugging my system. I think I may have overlooked a lot of what could be done in favor of simply uninstalling, reinstalling and formatting and starting from scratch. I have opened up the folder windows debugging tools, quite accidentally and just before I was going to clean sweep again, and I found KD and WinDbg. I had never seen these before and I felt that maybe I should look into this. I am quite familiar with the modern machine that is known as the computer, I know what a Kernel is and am now pretty familiar with at the very least Windows Operating System Services. I wish to begin tracking my own machines errors. I understand that most kernel debugging is done on a second machine but I don't have one. And also I understand the goal of the debugger seems to be less about run of the mill errors and more about development time strategies but I'm sure there is more to this. This is my first go at this and I thought maybe I could get some suggestions on where to go from here. I would really like to learn ways to fix my machine and also maybe pick up some tricks on the dev side as well. I hope this isn't too broad a question or too generalized. I'm really just looking for the keywords and an overview of the more routine strategies used. thx

Read the article
Lag spikes at full CPU usage, lagy mouse, maybe video card

- by Roberts

My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now 01.04.2012 (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can). Update 02.04.2012 - 7:21 Forgot one thing, my hard disk is extrimly slow and I will upgrade it this week or next week so I will be installing same OS again. I am multi-tasker but I can't do much because of 1.8 GHz CPU and slow hard drive (Model ID - WDC WD800JD-60JRC0). The Windows Experience Index is back to normal. Actually "Spelu grafika" (Gaming graphics) are higher than month ago. During this test mouse was very lagy, but month ago there weren't any problems. WHY!?

Read the article
What Apache/PHP configurations do you know and how good are they?

- by FractalizeR

Hello. I wanted to ask you about PHP/Apache configuration methods you know, their pros and cons. I will start myself: ---------------- PHP as Apache module---------------- Pros: good speed since you don't need to start exe every time especially in mpm-worker mode. You can also use various PHP accelerators in this mode like APC or eAccelerator. Cons: if you are running apache in mpm-worker mode, you may face stability issues because every glitch in any php script will lead to unstability to the whole thread pool of that apache process. Also in this mode all scripts are executed on behalf of apache user. This is bad for security. mpm-worker configuration requires PHP compiled in thread-safe mode. At least CentOS and RedHat default repositories doesn't have thread-safe PHP version so on these OSes you need to compile at least PHP yourself (there is a way to activate worker mpm on Apache). The use of thread-safe PHP binaries is considered experimental and unstable. Plus, many PHP extensions does not support thread-safe mode or were not well-tested in thread-safe mode. ---------------- PHP as CGI ---------------- This seems to be the slowest default configuration which seems to be a "con" itself ;) ---------------- PHP as CGI via mod_suphp ---------------- Pros: suphp allows you to execute php scipts on behalf of the script file owner. This way you can securely separate different sites on the same machine. Also, suphp allows to use different php.ini files per virtual host. Cons: PHP in CGI mode means less performance. In this mode you can't use php accelerators like APC because each time new process is spawned to handle script rendering the cache of previous process useless. BTW, do you know the way to apply some accelerator in this config? I heard something about using shm for php bytecode cache. Also, you cannot configure PHP via .htaccess files in this mode. You will need to install PECL htscanner for this if you need to set various per-script options via .htaccess (php_value / php_flag directives) ---------------- PHP as CGI via suexec ---------------- This configuration looks the same as with suphp, but I heard, that it's slower and less safe. Almost same pros and cons apply. ---------------- PHP as FastCGI ---------------- Pros: FastCGI standard allows single php process to handle several scripts before php process is killed. This way you gain performance since no need to spin up new php process for each script. You can also use PHP accelerators in this configuration (see cons section for comment). Also, FCGI almost like suphp also allows php processes to be executed on behalf of some user. mod_fcgid seems to have the most complete fcgi support and flexibility for apache. Cons: The use of php accelerator in fastcgi mode will lead to high memory consumption because each PHP process will have his own bytecode cache (unless there is some accelerator that can use shared memory for bytecode cache. Is there such?). FastCGI is also a little bit complex to configure. You need to create various configuration files and make some configuration modifications. It seems, that fastcgi is the most stable, secure, fast and flexible PHP configuration, however, a bit difficult to be configured. But, may be, I missed something? Comments are welcome!

Read the article
Fix overscan in Linux with Intel graphics Vizio HDTV

- by Padenton

I am connecting my server to my HDTV so that I can conveniently display it there. My VIZIO HDTV cuts off all 4 edges. I already realize it is not optimal to be running a GUI on a server; this server will not have much external traffic so I prefer it for convenience. I have already spent countless hours searching for a fix, but all I could find required an ATI or NVIDIA graphics card, or didn’t work. In Windows, the Intel driver has a setting for underscan, though it seems only to be available by a glitch. Here’s my specs: Ubuntu Linux (Quantal 12.10) (Likely to switch to Arch) This is a home server computer, with KDE for managing(for now, at least) Graphics: Intel HD Graphics 4000 from Ivy Bridge Motherboard: ASRock Z77 Extreme4 CPU: Intel Core i5-3450 My monitors: Dell LCD monitor Vizio VX37L_HDTV10A 37" on HDMI input I have tried all of the following from both HDMI?HDMI and DVI?HDMI cables connected to the ports on my motherboard: Setting properties in xrandr Making sure drivers are all up to date Trying several different modes The TV was “cheap”; max resolution 1080i. I am able to get a 1920x1080 modeline, in both GNU/Linux and Windows, without difficulty. There is no setting in the menu to fix the overscan (I have tried all of them, I realize it’s not always called overscan). I have been in the service menu for the TV, which still does not contain an option to fix it. No aspect ratio settings, etc. The TV has a VGA connector but I am unsure if it would fix it, as I don’t have a VGA cable long enough, and am not sure it would get me the 1920x1080 resolution which I want. Using another resolution does not fix the problem. I tried custom modelines with the dimensions of my screen’s viewable area, but it wouldn’t let me use them. Ubuntu apparently doesn’t automatically generate an xorg.conf file for use. I read somewhere that modifying it may help solve it. I tried X -configure several times(with reboots, etc.) but it consistently gave the following error messages: In log file: … (WW) Falling back to old probe method for vesa Number of created screens does not match number of detected devices. Configuration failed. In output: … (++) Using config file: "/root/xorg.conf.new" (==) Using system config directory "/usr/share/X11/xorg.conf.d" Number of created screens does not match number of detected devices. Configuration failed. Server terminated with error (2). Closing log file. Tried using 'overscan' prop in xrandr: root@xxx:/home/xxx# xrandr --output HDMI1 --set overscan off X Error of failed request: BadName (named color or font does not exist) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 11 (RRQueryOutputProperty) Serial number of failed request: 42 Current serial number in output stream: 42 'overscan on', 'underscan off', 'underscan on' were all also tried. Originally tried with Ubuntu 12.04, but failed and so updated to 12.10 when it was released. All software is up to date. I am not opposed to reinstalling my OS, likely will anyways (my preference being Arch).

Read the article
Windows 7, HTTPS WebDav: Asks for password twice and fails. Any workarounds?

- by AutoDMC

Howdy. I have a Dav server running with PHP SabreDav (code.google.com/p/sabredav/wiki/Windows) on Cherokee at an HTTPS secured URL. It's set to use https, and uses Digest Authentication. I can log in with multiple browsers and a few third party clients (BitKinex and Java AnyClient can connect and browse as well, caveats below). However, when attempting to log in with Windows 7 (surprise, surprise), it asks for my password twice, then tells me that my folder is invalid. I have verified that the server is using Digest authentication. I've verified multiple times that third party software can connect. I even went out and bought a GoDaddy SSL certificate so my SSL wouldn't be self signed anymore. I've applied the registry hacks here: support.microsoft.com/kb/943280 (Note that the article says the "fix" already exists for Windows 7, I just need magical registry hax to get it to work) I've applied the registry hacks here: support.microsoft.com/kb/941050 I've applied the registry hacks here: support.microsoft.com/kb/841215 (Supposedly allows Basic Auth, which shouldn't apply, but why not?) All to no avail; Windows continues to ask for my password twice, then state that "The folder you entered does not appear to be valid. Please choose another." Try the command line? Sure: I've attempted to access with NET USE "https://dav.example.com/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/" (System error 1790) I've attempted to access with NET USE "https://dav.example.com/subdir/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/subdir/" (System error 1790) For good luck: ping dav.example.com ... works. And again, web browsers can access the share just fine, so can third party tools. Best I can tell at this point is "HAHA, NO WEBDAV FOR YOU ON WINDOWS 7" which would be fine except everyone who will be using this application... uses Windows 7. And most are not as persistent or pugnacious as I am. I feel like I've burned through every random suggestion I've found anywhere in the first 10 pages of Google on every search term I can think of. Any ideas? I need it to be Webdav, I need it to be over HTTPS, and I really do need a method to access it from Windows 7. EXTRA DETAIL: However, the "third party" programs I've tried have either been buggy, incomplete, or have silly ... "glitches." For example, BitKinex seems to fixate on any http error codes sent, so if there's a glitch reading a directory, BAM, that directory is always listed empty. Long directory listings also show up as blank, even though the transfer panel shows that directory listing is still taking place. In any case, BitKinex is useless for development purposes for the reasons above. And besides, I'm building this for people other than myself, people who will want to get this dav share working "the regular way."

Read the article
SQLAuthority News – Pluralsight Course Review – Practices for Software Startups – Part 2 of 2

- by pinaldave

This is the second part of the two part series of Practices for Software Startup Pluralsight Course. Please read the first part of this series over here. The course is written by Stephen Forte (Blog | Twitter). Stephen Forte is the Chief Strategy Officer of the venture backed company, Telerik. Personal Learning Schedule After these three sessions it was 6:30 am and time to do my own blog. But for the rest of the day, I kept thinking about the course, and wanted to go back and finish. I was wishing that I had woken up at 3 am so I could finish all at one go. All day long I was digesting what I had learned. At 10 pm, after my daughter had gone to bed, I sighed on again. I was not disappointed by the long wait. As I mentioned before, Stephen has started four to six companies, and all of them are very successful today. Here is the video I promised yesterday – it discusses the importance of Right Sizing Your Startup. The Heartbeat of Startup – Technology Stephen has combined all technology knowledge into one 30 minute session. He discussed how to start your project, how to deal with opinions, and how to deal with multiple ideas – every start up has multiple directions it can go. He spent a lot of time emphasized deciding which direction to go and how to decide which will be the best for you. He called it a continuous development cycle. One of the biggest hazards for a start-up company is one person deciding the direction the company will go, until down the road another team member announces that there is a glitch in their part of the work and that everyone will have to start over. Even though a team of two or five people can move quickly, often the decision has gone too long and cannot be easily fixed. Stephen used an example from his own life: he was biased for one type of technology, and his teammate for another. In the end they opted for his teammate’s choice , and in the end it was a good decision, even though he was unfamiliar with that particular program. He argues that technology should not be a barrier to progress, that you cannot rely on your experience only. This really spoke to me because I am a big fan of SQL, but I know there is more out there, and I should be more open to it. I give my thanks to Stephen, I learned something in this module besides startups. Money, Success and Epic Win! The longest, but most interesting, the module was funding your start-up. You need to fund the start-up right at the very beginning, if not done right you will run into trouble. The good news is that a few years ago start-ups required a lot more money – think millions of dollars – but now start-ups can get off the ground for thousands. Stephen used an example of a company that years ago would have needed a million dollars, but today could be started for $600. It is true that things have changed, but you still need money. For $600 you can start small and add dynamically, as needed. But the truth is that if you have $600, $6000, or $6 million, it will be spent. Don’t think of it as trying to save money, think of it as investing in your future. You will need money, and you will need to (quickly) decide what you do with the money: shares, stakeholders, investing in a team, hiring a CEO. This is so important because once you have money and start the company, the company IS your money. It is your biggest currency – having a percentage of ownership in the company. Investors will want percentages as repayment for their investment, and they will want a say in the business as well. You will have to decide how far you will dilute your shares, and how the company will be divided, if at all. If you don’t plan in advance, you will find that after gaining three or four investors, suddenly you are the minority owner in your own dream. You need to understand funding carefully. This single module is worth all the money you would have spent on the whole course alone. I encourage everyone to listen to this single module even if they don’t watch any of the others. Press End to Start the Game – Exists! The final module is exit strategies. You did all this work, dealt with all political and legal issues. What are you going to get out of it? The answer is simple: money. Maybe you want your company to be bought out, for you talent to bring you a profit. You can sell the company to someone and still head it. Many options are available. You could sell and still work as an employee but no longer own the company. There are many exit strategies. This is where all your hard work comes into play. It is important not to feel fooled at any step. There are so many good ideas that end up in the garbage because of poor planning, so that if you find yourself successful, you don’t want to blow it at this step! The exit is important. I thought that this aspect of the course was completely unique, and I loved Stephen’s point of view. I was lost deep in thought after this module ended. I actually took two hours worth of notes on this section alone – and it was only a three hour course. I am planning on attending this course one more time next week, just to catch up on all the small bits of wisdom I’m sure I missed. Thank you Stephen for bringing your real world experience with us! I recommend that everyone attends this course, even if they don’t want to begin their own start-up company. It was indeed a long day for me. Do not forget to read part 1 of this story and attend course Practices for Software Startup Pluralsight Course. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Best Practices, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

Read the article
Hard drive mounted at / , duplicate mounted hard drive after using MountManager

- by HellHarvest

possible duplicate post I'm running 12.04 64bit. My system is a dual boot for both Ubuntu and Windows7. Both operating systems are sharing the drive named "Elements". My volume named "Elements" is a 1TB SATA NTFS hard drive that shows up twice in the side bar in nautilus. One of the icons is functional and even has the convenient "eject" icon next to it. Below is a picture of the left menu in Nautilus, with System Monitor-File Systems tab open on top of it. Can someone advise me about how to get rid of this extra icon? I think the problem is much more deep-rooted than just a GUI glitch on Nautilus' part. The other icon does nothing but spit out the following error when I click on it (image below). This only happened AFTER I tried using Mount Manager to automate mounting the drive at start up. I've already uninstalled Mount Manager, and restarted, but the problem didn't go away. The hard drive does mount automatically now, so I guess that's cool. But now, every time I boot up now and open Nautilus, BOTH of these icons appear, one of which is fictitious and useless. According to the image above and the outputs of several other commands, it appears to be mounted at / In which case, no matter where I am in Nautilus when I try to click on that icon, of course it will tell me that that drive is in use by another program... Nautilus. I'm afraid of trying to unmount this hard drive (sdb6) because of where it appears to be mounted. I'm kind of a noob, and I have this gut feeling that tells me trying to unmount a drive at / will destroy my entire file system. This fear was further strengthened by the output of "$ fsck" at the very bottom of this post. Error immediately below when that 2nd "Elements" hard drive is clicked in Nautilus: Unable to mount Elements Mount is denied because the NTFS volume is already exclusively opened. The volume may be already mounted, or another software may use it which could be identified for example by the help of the 'fuser' command. It's odd to me that that error message above claims that it's an NTFS volume when everything else tell me that it's an ext4 volume. The actual hard drive "Elements" is in fact an NTFS volume. Here's the output of a few commands and configuration files that may be of interest: $ fuser -a / /: 2120r 2159rc 2160rc 2172r 2178rc 2180rc 2188r 2191rc 2200rc 2203rc 2205rc 2206r 2211r 2212r 2214r 2220r 2228r 2234rc 2246rc 2249rc 2254rc 2260rc 2261r 2262r 2277rc 2287rc 2291rc 2311rc 2313rc 2332rc 2334rc 2339rc 2343rc 2344rc 2352rc 2372rc 2389rc 2422r 2490r 2496rc 2501rc 2566r 2573rc 2581rc 2589rc 2592r 2603r 2611rc 2613rc 2615rc 2678rc 2927r 2981r 3104rc 4156rc 4196rc 4206rc 4213rc 4240rc 4297rc 5032rc 7609r 7613r 7648r 9593rc 18829r 18833r 19776r $ sudo df -h Filesystem Size Used Avail Use% Mounted on /dev/sdb6 496G 366G 106G 78% / udev 2.0G 4.0K 2.0G 1% /dev tmpfs 791M 1.5M 790M 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.0G 672K 2.0G 1% /run/shm /dev/sda1 932G 312G 620G 34% /media/Elements /home/solderblob/.Private 496G 366G 106G 78% /home/solderblob /dev/sdb2 188G 100G 88G 54% /media/A2B24EACB24E852F /dev/sdb1 100M 25M 76M 25% /media/System Reserved $ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00093cab Device Boot Start End Blocks Id System /dev/sda1 2048 1953519615 976758784 7 HPFS/NTFS/exFAT Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e8d9b Device Boot Start End Blocks Id System /dev/sdb1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sdb2 206848 392378768 196085960+ 7 HPFS/NTFS/exFAT /dev/sdb3 392380414 1465147391 536383489 5 Extended /dev/sdb5 1456762880 1465147391 4192256 82 Linux swap / Solaris /dev/sdb6 392380416 1448374271 527996928 83 Linux /dev/sdb7 1448376320 1456758783 4191232 82 Linux swap / Solaris Partition table entries are not in disk order $ cat /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> UUID=77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 defaults 0 1 UUID=F6549CC4549C88CF /media/Elements ntfs-3g users 0 0 $ sudo blkid /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ sudo blkid -c /dev/null (appears to be exactly the same as above) /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ mount /dev/sdb6 on / type ext4 (rw) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /media/Elements type fuseblk (rw,noexec,nosuid,nodev,allow_other,blksize=4096) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) /home/solderblob/.Private on /home/solderblob type ecryptfs (ecryptfs_check_dev_ruid,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs,ecryptfs_sig=76a47b0175afa48d,ecryptfs_fnek_sig=391b2d8b155215f7) gvfs-fuse-daemon on /home/solderblob/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=solderblob) /dev/sdb2 on /media/A2B24EACB24E852F type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) /dev/sdb1 on /media/System Reserved type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) $ ls -a . A2B24EACB24E852F Ubuntu 12.04.1 LTS amd64 .. Elements System Reserved $ cat /proc/mounts rootfs / rootfs rw 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev devtmpfs rw,relatime,size=2013000k,nr_inodes=503250,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 tmpfs /run tmpfs rw,nosuid,relatime,size=809872k,mode=755 0 0 /dev/disk/by-uuid/77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 rw,relatime,user_xattr,acl,barrier=1,data=ordered 0 0 none /sys/fs/fuse/connections fusectl rw,relatime 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 none /sys/kernel/security securityfs rw,relatime 0 0 none /run/lock tmpfs rw,nosuid,nodev,noexec,relatime,size=5120k 0 0 none /run/shm tmpfs rw,nosuid,nodev,relatime 0 0 /dev/sda1 /media/Elements fuseblk rw,nosuid,nodev,noexec,relatime,user_id=0,group_id=0,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 /home/solderblob/.Private /home/solderblob ecryptfs rw,relatime,ecryptfs_fnek_sig=391b2d8b155215f7,ecryptfs_sig=76a47b0175afa48d,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs 0 0 gvfs-fuse-daemon /home/solderblob/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0 /dev/sdb2 /media/A2B24EACB24E852F fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 /dev/sdb1 /media/System\040Reserved fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 gvfs-fuse-daemon /root/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=0,group_id=0 0 0 $ fsck fsck from util-linux 2.20.1 e2fsck 1.42 (29-Nov-2011) /dev/sdb6 is mounted. WARNING!!! The filesystem is mounted. If you continue you ***WILL*** cause ***SEVERE*** filesystem damage. Do you really want to continue<n>? no check aborted.

Read the article
Ogre 3d and bullet physics interaction

- by Tim

I have been playing around with Ogre3d and trying to integrate bullet physics. I have previously somewhat successfully got this functionality working with irrlicht and bullet and I am trying to base this on what I had done there, but modifying it to fit with Ogre. It is working but not correctly and I would like some help to understand what it is I am doing wrong. I have a state system and when I enter the "gamestate" I call some functions such as setting up a basic scene, creating the physics simulation. I am doing that as follows. void GameState::enter() { ... // Setup Physics btBroadphaseInterface *BroadPhase = new btAxisSweep3(btVector3(-1000,-1000,-1000), btVector3(1000,1000,1000)); btDefaultCollisionConfiguration *CollisionConfiguration = new btDefaultCollisionConfiguration(); btCollisionDispatcher *Dispatcher = new btCollisionDispatcher(CollisionConfiguration); btSequentialImpulseConstraintSolver *Solver = new btSequentialImpulseConstraintSolver(); World = new btDiscreteDynamicsWorld(Dispatcher, BroadPhase, Solver, CollisionConfiguration); ... createScene(); } In the createScene method I add a light and try to setup a "ground" plane to act as the ground for things to collide with.. as follows. I expect there is issues with this as I get objects colliding with the ground but half way through it and they glitch around like crazy on collision. void GameState::createScene() { m_pSceneMgr->createLight("Light")->setPosition(75,75,75); // Physics // As a test we want a floor plane for things to collide with Ogre::Entity *ent; Ogre::Plane p; p.normal = Ogre::Vector3(0,1,0); p.d = 0; Ogre::MeshManager::getSingleton().createPlane( "FloorPlane", Ogre::ResourceGroupManager::DEFAULT_RESOURCE_GROUP_NAME, p, 200000, 200000, 20, 20, true, 1, 9000,9000,Ogre::Vector3::UNIT_Z); ent = m_pSceneMgr->createEntity("floor", "FloorPlane"); ent->setMaterialName("Test/Floor"); Ogre::SceneNode *node = m_pSceneMgr->getRootSceneNode()->createChildSceneNode(); node->attachObject(ent); btTransform Transform; Transform.setIdentity(); Transform.setOrigin(btVector3(0,1,0)); // Give it to the motion state btDefaultMotionState *MotionState = new btDefaultMotionState(Transform); btCollisionShape *Shape = new btStaticPlaneShape(btVector3(0,1,0),0); // Add Mass btVector3 LocalInertia; Shape->calculateLocalInertia(0, LocalInertia); // CReate the rigid body object btRigidBody *RigidBody = new btRigidBody(0, MotionState, Shape, LocalInertia); // Store a pointer to the Ogre Node so we can update it later RigidBody->setUserPointer((void *) (node)); // Add it to the physics world World->addRigidBody(RigidBody); Objects.push_back(RigidBody); m_pNumEntities++; // End Physics } I then have a method to create a cube and give it rigid body physics properties. I know there will be errors here as I get the items colliding with the ground but not with each other properly. So I would appreciate some input on what I am doing wrong. void GameState::CreateBox(const btVector3 &TPosition, const btVector3 &TScale, btScalar TMass) { Ogre::Vector3 size = Ogre::Vector3::ZERO; Ogre::Vector3 pos = Ogre::Vector3::ZERO; Ogre::Vector3 scale = Ogre::Vector3::ZERO; pos.x = TPosition.getX(); pos.y = TPosition.getY(); pos.z = TPosition.getZ(); scale.x = TScale.getX(); scale.y = TScale.getY(); scale.z = TScale.getZ(); Ogre::Entity *entity = m_pSceneMgr->createEntity( "Box" + Ogre::StringConverter::toString(m_pNumEntities), "cube.mesh"); entity->setCastShadows(true); Ogre::AxisAlignedBox boundingB = entity->getBoundingBox(); size = boundingB.getSize(); //size /= 2.0f; // Only the half needed? //size *= 0.96f; // Bullet margin is a bit bigger so we need a smaller size entity->setMaterialName("Test/Cube"); Ogre::SceneNode *node = m_pSceneMgr->getRootSceneNode()->createChildSceneNode(); node->attachObject(entity); node->setPosition(pos); //node->scale(scale); // Physics btTransform Transform; Transform.setIdentity(); Transform.setOrigin(TPosition); // Give it to the motion state btDefaultMotionState *MotionState = new btDefaultMotionState(Transform); btVector3 HalfExtents(TScale.getX()*0.5f,TScale.getY()*0.5f,TScale.getZ()*0.5f); btCollisionShape *Shape = new btBoxShape(HalfExtents); // Add Mass btVector3 LocalInertia; Shape->calculateLocalInertia(TMass, LocalInertia); // CReate the rigid body object btRigidBody *RigidBody = new btRigidBody(TMass, MotionState, Shape, LocalInertia); // Store a pointer to the Ogre Node so we can update it later RigidBody->setUserPointer((void *) (node)); // Add it to the physics world World->addRigidBody(RigidBody); Objects.push_back(RigidBody); m_pNumEntities++; } Then in the GameState::update() method which which runs every frame to handle input and render etc I call an UpdatePhysics method to update the physics simulation. void GameState::UpdatePhysics(unsigned int TDeltaTime) { World->stepSimulation(TDeltaTime * 0.001f, 60); btRigidBody *TObject; for(std::vector<btRigidBody *>::iterator it = Objects.begin(); it != Objects.end(); ++it) { // Update renderer Ogre::SceneNode *node = static_cast<Ogre::SceneNode *>((*it)->getUserPointer()); TObject = *it; // Set position btVector3 Point = TObject->getCenterOfMassPosition(); node->setPosition(Ogre::Vector3((float)Point[0], (float)Point[1], (float)Point[2])); // set rotation btVector3 EulerRotation; QuaternionToEuler(TObject->getOrientation(), EulerRotation); node->setOrientation(1,(Ogre::Real)EulerRotation[0], (Ogre::Real)EulerRotation[1], (Ogre::Real)EulerRotation[2]); //node->rotate(Ogre::Vector3(EulerRotation[0], EulerRotation[1], EulerRotation[2])); } } void GameState::QuaternionToEuler(const btQuaternion &TQuat, btVector3 &TEuler) { btScalar W = TQuat.getW(); btScalar X = TQuat.getX(); btScalar Y = TQuat.getY(); btScalar Z = TQuat.getZ(); float WSquared = W * W; float XSquared = X * X; float YSquared = Y * Y; float ZSquared = Z * Z; TEuler.setX(atan2f(2.0f * (Y * Z + X * W), -XSquared - YSquared + ZSquared + WSquared)); TEuler.setY(asinf(-2.0f * (X * Z - Y * W))); TEuler.setZ(atan2f(2.0f * (X * Y + Z * W), XSquared - YSquared - ZSquared + WSquared)); TEuler *= RADTODEG; } I seem to have issues with the cubes not colliding with each other and colliding strangely with the ground. I have tried to capture the effect with the attached image. I would appreciate any help in understanding what I have done wrong. Thanks. EDIT : Solution The following code shows the changes I made to get accurate physics. void GameState::createScene() { m_pSceneMgr->createLight("Light")->setPosition(75,75,75); // Physics // As a test we want a floor plane for things to collide with Ogre::Entity *ent; Ogre::Plane p; p.normal = Ogre::Vector3(0,1,0); p.d = 0; Ogre::MeshManager::getSingleton().createPlane( "FloorPlane", Ogre::ResourceGroupManager::DEFAULT_RESOURCE_GROUP_NAME, p, 200000, 200000, 20, 20, true, 1, 9000,9000,Ogre::Vector3::UNIT_Z); ent = m_pSceneMgr->createEntity("floor", "FloorPlane"); ent->setMaterialName("Test/Floor"); Ogre::SceneNode *node = m_pSceneMgr->getRootSceneNode()->createChildSceneNode(); node->attachObject(ent); btTransform Transform; Transform.setIdentity(); // Fixed the transform vector here for y back to 0 to stop the objects sinking into the ground. Transform.setOrigin(btVector3(0,0,0)); // Give it to the motion state btDefaultMotionState *MotionState = new btDefaultMotionState(Transform); btCollisionShape *Shape = new btStaticPlaneShape(btVector3(0,1,0),0); // Add Mass btVector3 LocalInertia; Shape->calculateLocalInertia(0, LocalInertia); // CReate the rigid body object btRigidBody *RigidBody = new btRigidBody(0, MotionState, Shape, LocalInertia); // Store a pointer to the Ogre Node so we can update it later RigidBody->setUserPointer((void *) (node)); // Add it to the physics world World->addRigidBody(RigidBody); Objects.push_back(RigidBody); m_pNumEntities++; // End Physics } void GameState::CreateBox(const btVector3 &TPosition, const btVector3 &TScale, btScalar TMass) { Ogre::Vector3 size = Ogre::Vector3::ZERO; Ogre::Vector3 pos = Ogre::Vector3::ZERO; Ogre::Vector3 scale = Ogre::Vector3::ZERO; pos.x = TPosition.getX(); pos.y = TPosition.getY(); pos.z = TPosition.getZ(); scale.x = TScale.getX(); scale.y = TScale.getY(); scale.z = TScale.getZ(); Ogre::Entity *entity = m_pSceneMgr->createEntity( "Box" + Ogre::StringConverter::toString(m_pNumEntities), "cube.mesh"); entity->setCastShadows(true); Ogre::AxisAlignedBox boundingB = entity->getBoundingBox(); // The ogre bounding box is slightly bigger so I am reducing it for // use with the rigid body. size = boundingB.getSize()*0.95f; entity->setMaterialName("Test/Cube"); Ogre::SceneNode *node = m_pSceneMgr->getRootSceneNode()->createChildSceneNode(); node->attachObject(entity); node->setPosition(pos); node->showBoundingBox(true); //node->scale(scale); // Physics btTransform Transform; Transform.setIdentity(); Transform.setOrigin(TPosition); // Give it to the motion state btDefaultMotionState *MotionState = new btDefaultMotionState(Transform); // I got the size of the bounding box above but wasn't using it to set // the size for the rigid body. This now does. btVector3 HalfExtents(size.x*0.5f,size.y*0.5f,size.z*0.5f); btCollisionShape *Shape = new btBoxShape(HalfExtents); // Add Mass btVector3 LocalInertia; Shape->calculateLocalInertia(TMass, LocalInertia); // CReate the rigid body object btRigidBody *RigidBody = new btRigidBody(TMass, MotionState, Shape, LocalInertia); // Store a pointer to the Ogre Node so we can update it later RigidBody->setUserPointer((void *) (node)); // Add it to the physics world World->addRigidBody(RigidBody); Objects.push_back(RigidBody); m_pNumEntities++; } void GameState::UpdatePhysics(unsigned int TDeltaTime) { World->stepSimulation(TDeltaTime * 0.001f, 60); btRigidBody *TObject; for(std::vector<btRigidBody *>::iterator it = Objects.begin(); it != Objects.end(); ++it) { // Update renderer Ogre::SceneNode *node = static_cast<Ogre::SceneNode *>((*it)->getUserPointer()); TObject = *it; // Set position btVector3 Point = TObject->getCenterOfMassPosition(); node->setPosition(Ogre::Vector3((float)Point[0], (float)Point[1], (float)Point[2])); // Convert the bullet Quaternion to an Ogre quaternion btQuaternion btq = TObject->getOrientation(); Ogre::Quaternion quart = Ogre::Quaternion(btq.w(),btq.x(),btq.y(),btq.z()); // use the quaternion with setOrientation node->setOrientation(quart); } } The QuaternionToEuler function isn't needed so that was removed from code and header files. The objects now collide with the ground and each other appropriately.

Read the article
CodePlex Daily Summary for Tuesday, May 29, 2012

CodePlex Daily Summary for Tuesday, May 29, 2012Popular ReleasesDotNetNuke Azure Accelerator: DotNetNuke Azure Accelerator 6.2: Windows Azure deployments of DotNetNuke Community using virtual hard drive (cloud-drive) image that is created dynamically on the cloud. Enables the creation of new DotNetNuke host instances from on-premise to the cloud using a wizard that guides you on this process, creating the SQL Azure database, uploading the solution engine and associated service configurations. New features in this releaseModified the web roles endpoints to allow traffic on port 443 Changed the package unzip operati...Thales Simulator Library: Version 0.9.6: The Thales Simulator Library is an implementation of a software emulation of the Thales (formerly Zaxus & Racal) Hardware Security Module cryptographic device. This release fixes a problem with the FK command and a bug in the implementation of PIN block 05 format deconstruction. A new 0.9.6.Binaries file has been posted. This includes executable programs without an installer, including the GUI and console simulators, the key manager and the PVV clashing demo. Please note that you will need ...myManga: myManga v1.0.0.2: Fixed the 'Lost+Brain' error on MangaReader. The main download has this update. The second download is for those who have already downloaded the old v1.0.0.2. DELETE OLD EXE and DLLs before you copy the new files over.To update from v1.0.0.1:Extract new myManga EXE and DLLs from Zip to folder of choosing. Copy MangaInfo and MangaArchives folder from old myManga folder to new folder from step 1. ORDelete: The new myManga.exe contains the CoreMangaClasses.dll and Manga.dll internally. Delet...????: ????2.0.1: 1、?????。WiX Toolset: WiX v3.6 RC: WiX v3.6 RC (3.6.2928.0) provides feature complete Burn with VS11 support. For more information see Rob's blog post about the release: http://robmensching.com/blog/posts/2012/5/28/WiX-v3.6-Release-Candidate-availableJavascript .NET: Javascript .NET v0.7: SetParameter() reverts to its old behaviour of allowing JavaScript code to add new properties to wrapped C# objects. The behavior added briefly in 0.6 (throws an exception) can be had via the new SetParameterOptions.RejectUnknownProperties. TerminateExecution now uses its isolate to terminate the correct context automatically. Added support for converting all C# integral types, decimal and enums to JavaScript numbers. (Previously only the common types were handled properly.) Bug fixe...Indent Guides for Visual Studio: Indent Guides v12: Version History Changed in v12: background document analysis new options dialog with Quick Set selections for behavior new "glow" style for guides new menu icon in VS 11 preview control now uses editor theming highlighting can be customised on each line fixed issues with collapsed code blocks improved behaviour around left-aligned pragma/preprocessor commands (C#/C++) new settings for controlling guides in empty lines restructured settings storage (should be more reliable) ...callisto: callisto 2.0.29: Added DNS functionality to scripting. See documentation section for details of how to incorporate this into your scripts.ZXMAK2: Version 2.6.2.2: - implemented read port #7FFD glitch for ULA128 (fusetest) - fix unhandled exception inside open dialog - fix Z80 format serializer (support 55 bytes header & non compressed 128 blocks - thanks to Ralf) This release include SPRINTER emulation, but boot system disk image was removed.Phalanger - The PHP Language Compiler for the .NET Framework: 3.0 (May 2012): Fixes: unserialize() of negative float numbers fix pcre possesive quantifiers and character class containing ()[] array deserilization when the array contains a reference to ISerializable parsing lambda function fix round() reimplemented as it is in PHP to avoid .NET rounding errors filesize bypass for FileInfo.Length bug in Mono New features: Time zones reimplemented, uses Windows/Linux databaseSharePoint Euro 2012 - UEFA European Football Predictor: havivi.euro2012.wsp (1.1): New fetures:Admin enable / disable match Hide/Show Euro 2012 SharePoint lists (3 lists) Installing SharePoint Euro 2012 PredictorSharePoint Euro 2012 Predictor has been developed as a SharePoint Sandbox solution to support SharePoint Online (Office 365) Download the solution havivi.euro2012.wsp from the download page: Downloads Upload this solution to your Site Collection via the solutions area. Click on Activate to make the web parts in the solution available for use in the Site C...ScreenShot: InstallScreenShot: This is the current stable release.????SDK for .Net 4.0+(OAuth2.0+??V2?API): ??V2?SDK???: ????SDK for .Net 4.X???????PHP?SDK???OAuth??API???Client???。 ??????API?? ???????OAuth2.0???? ???：????????，DEMO??AppKey????????????????，?????AppKey，????AppKey???????????，?????“????>????>????>??????”.Net Code Samples: Code Samples: Code samples (SLNs).LINQ_Koans: LinqKoans v.02: Cleaned up a bitExpression Tree Visualizer for VS 2010: Expression Tree Visualizer Beta: This is a beta release, in this release some expression types are not handled and use a default visualization behavior. The first release will be published soon. Wait for it...Ulfi: Ulfi source: Build with Visual Studio 2010 Express C# or betterJayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.0 RC1 Refresh 2: JayData is a unified data access library for JavaScript developers to query and update data from different sources like webSQL, indexedDB, OData, Facebook or YQL. See it in action in this 6 minutes video: http://www.youtube.com/watch?v=LlJHgj1y0CU RC1 R2 Release highlights Knockout.js integrationUsing the Knockout.js module, your UI can be automatically refreshed when the data model changes, so you can develop the front-end of your data manager app even faster. Querying 1:N relations in W...Christoc's DotNetNuke Module Development Template: 00.00.08 for DNN6: BEFORE USE YOU need to install the MSBuild Community Tasks available from http://msbuildtasks.tigris.org For best results you should configure your development environment as described in this blog post Then read this latest blog post about customizing and using these custom templates. Installation is simple To use this template place the ZIP (not extracted) file in your My Documents\Visual Studio 2010\Templates\ProjectTemplates\Visual C#\Web OR for VB My Documents\Visual Studio 2010\Te...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.53: fix issue #18106, where member operators on numeric literals caused the member part to be duplicated when not minifying numeric literals ADD NEW FEATURE: ability to create source map files! The first mapfile format to be supported is the Script# format. Use the new -map filename switch to create map files when building your sources.New ProjectsActive Log Reader: The active log reader provides the ability for a client to subscribe to specific changes in a set of files in a directory. For example, it allows you to actively monitor all .log files in your C:\Windows directory (and sub-directories) and callback whenever the word "ERROR" shows up (or any regular expression you can come up with). The accompanying test project outlines example usage.ADO.NET light wrapper: ADO.NET light wrapper is thin IEnumerable layer about ADO.NET for provide easy way to access data with strong typing support. Allen Neighborhood Center: Allen Neighborhood Center data interactionsCildads: The first attempt at centryCMT: Course Management Tool ProjectCode Builder: this is the Builder project.Connect: this is the Connect project.Craig's Framework: A basic framework that is used to speed up building MVC applications and make certain things simpler.CRM 2011 Fetch XML Execute Tool: This is a dev tool used to execute fetch xml to get the results from the connected CRM 2011 instanceDallasDB: A struct based database. DallasDB will have no full functionality until at least version 0.0.1, and won't be ready for professional use until version 1.0.0. EasyMvc: It provides a trainning sample to develop a web application base on MVC3 EF4.0 SQL Compact 4. Besides, a common business permission, logging, configration have been applied simply. Share with some implement idea about web, mvc, jquery,orm. Appreciate your advice.Entity: this is the Entity project.FogLampz: FogLampz is a .NET wrapper around around the FogBugz API.Geeba: Geeba Forum for Students in BGU UniversityHibernate: this is the Hibernate project.JSense - IntelliSense for JavaScript: JSense provides JavaScript IntelliSense meta-automation for Visual Studio 2010 projectsMichael: this is Michael's project.ModAdder: Minecraft Mod InstallerMVVM ORM: The purpose of MVVM ORM is to create models and their interactions as defined in some database for WPF applications Models are derived from tables, views and stored procedures. Interactions include insert/update/delete, with FK relationships taken into account. nihao: The summary is required.Report: this is the Report project.REST Start Kit for BizTalk: This project enables BizTalk Server to expose RESTFul services through the WCF-Custom adapter. The library supports both receive and send, both XML and JSON with all HTTP verbs (GET, POST, PUT and DELETE). The solution is based on two custom WCF behaviors, one to be used on Receive Locations and one on Send Ports. Hopeully you'll find them easy to use, but if you have any issues, please use the discussions forum.RovignetaWinPhone7: bla bla blaScreenShot: A simple utility that enhances the experience of taking screenshots and annotating them. And all of it happens with the screenshot key that you are most used to. PrintScreen. Give it a try. You will forget the traditional tedious screenshot mechanism.SDM Exam 2012: This is an exam project for 4th semester.Struts: this is the Struts project.TheStoreDepot: depot for the StoreTibiaBot: TibiaBot is an open source application dedicated to extend your gaming experience in MMORPG game called Tibia. Besides of very many built-in functions, TibiaBot has implemented IronRuby script engine, which allows You to creating new functionality to base program.TopicInterDisciplinary: Topic inter-disciplinary owner: sherry, chen1984yangWebAppMatrix: ??WebApp??，?????！

Read the article
Why does an error appear every time I try to open the Ubuntu Software Center? [duplicate]

- by askubuntu7639

This question already has an answer here: How do I remove a broken software source? 3 answers There is a glitch on the Ubuntu Software Center and whenever I open it an error appears and it keeps loading and never opens. Why does this happen? I have installed Ubuntu 13.04 on a disk and partitioned it. Please help me and ask for excess information if you need it. If you know of any duplicates please show me them!! This is the output of a question someone asked me. SystemError: E:Type '<!DOCTYPE' is not known on line 1 in source list /etc/apt/sources.list.d/medibuntu.list This next output is the output of cat /etc/apt/sources.list.d/medibuntu.list </div> <div style="float:left;"> <div class="textwidget"><script type="text/javascript"> </div> Unixmen Archive Select Month September 2013 August 2013 July 2013 June 2013 May 2013 April 2013 March 2013 February 2013 January 2013 December 2012 November 2012 October 2012 September 2012 August 2012 July 2012 June 2012 May 2012 April 2012 March 2012 February 2012 January 2012 December 2011 November 2011 October 2011 September 2011 August 2011 July 2011 June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 November 2010 October 2010 September 2010 August 2010 July 2010 June 2010 May 2010 April 2010 March 2010 February 2010 January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 2009 December 2008 Tags Cloudandroid apache browser Centos chrome command line Debian eyecandy Fedora firefox games gaming gnome google karmic koala kde libreoffice Linux linux distribution LinuxMint lucid lynx maverick meerkat mysql news oneiric ocelot openoffice opensource opensuse oracle ppa Precise Pangolin release RHEL security server software themes tools ubuntu unix upgrade virtualbox vlc windows wine Unixmen Twitts Firefox 16, a treat for developers http://t.co/cnd27CzT Ubuntu 12.10 ‘Quantal Quetzal’: Beta 2 Sneak Peek http://t.co/hd4LwDOy Top 5 security Myths about Linux; and their realities http://t.co/zO1LgHST About Us Advertising Sitemap Privacy Contact Us Hire Us Copyright © 2008-2013 Unixmen.com . Maintained by Unixmen . /* */ jQuery(document).on('ready post-load', easy_fancybox_handler ); http://www.w3-edge.com/wordpress-plugins/ Page Caching using apc Database Caching 3/186 queries in 0.035 seconds using apc Content Delivery Network via 180016988.r.cdn77.net Served from: www.unixmen.com @ 2013-09-25 01:38:14 by W3 Total Cache

Read the article
Why does virtual assignment behave differently than other virtual functions of the same signature?

- by David Rodríguez - dribeas

While playing with implementing a virtual assignment operator I have ended with a funny behavior. It is not a compiler glitch, since g++ 4.1, 4.3 and VS 2005 share the same behavior. Basically, the virtual operator= behaves differently than any other virtual function with respect to the code that is actually being executed. struct Base { virtual Base& f( Base const & ) { std::cout << "Base::f(Base const &)" << std::endl; return *this; } virtual Base& operator=( Base const & ) { std::cout << "Base::operator=(Base const &)" << std::endl; return *this; } }; struct Derived : public Base { virtual Base& f( Base const & ) { std::cout << "Derived::f(Base const &)" << std::endl; return *this; } virtual Base& operator=( Base const & ) { std::cout << "Derived::operator=( Base const & )" << std::endl; return *this; } }; int main() { Derived a, b; a.f( b ); // [0] outputs: Derived::f(Base const &) (expected result) a = b; // [1] outputs: Base::operator=(Base const &) Base & ba = a; Base & bb = b; ba = bb; // [2] outputs: Derived::operator=(Base const &) Derived & da = a; Derived & db = b; da = db; // [3] outputs: Base::operator=(Base const &) ba = da; // [4] outputs: Derived::operator=(Base const &) da = ba; // [5] outputs: Derived::operator=(Base const &) } The effect is that the virtual operator= has a different behavior than any other virtual function with the same signature ([0] compared to [1]), by calling the Base version of the operator when called through real Derived objects ([1]) or Derived references ([3]) while it does perform as a regular virtual function when called through Base references ([2]), or when either the lvalue or rvalue are Base references and the other a Derived reference ([4],[5]). Is there any sensible explanation to this odd behavior?

Read the article
Calling popToRootViewControllerAnimated causing crash. How should I be doing this?

- by Lewis42

The app is for taking body measurements. The user can say I want to measure: legs, arms and neck, in the settings tab and in the main tab there is a view which loops round to take each measurement. This is achieved like so: i have tab controller the first tab has a navigation controller the first view controller on the storyboard and has one segue to itself the board loops round until it has all the measurements then it segues to a different controller the problem is: if the user changes which measurements they are taking in the settings tab, the first tab needs to completely reload, as if the app was just starting up, clearing down the whole nav stack etc. at the moment the tab controller calls popToRootViewControllerAnimated on the navigation controller in the measurements tab, but this is causing a crash. Each screen has a slider control and a call to titleForRow:forComponent: is being called on a deleted view causing it to crash. What am I doing wrong?! Here's the tab bar controller code // TabBarController.m // #import "TabBarController.h" #import "TodaysMeasurementObject.h" #import "AppDelegateProtocol.h" #import "AddMeasurementViewController.h" #import "ReadPerson.h" #import "AppDelegate.h" @interface TabBarController () <UITabBarControllerDelegate> @end @implementation TabBarController bool resetWizardView = false; - (id)initWithNibName:(NSString *)nibNameOrNil bundle:(NSBundle *)nibBundleOrNil { self = [super initWithNibName:nibNameOrNil bundle:nibBundleOrNil]; if (self) { } return self; } - (void)viewDidLoad { [super viewDidLoad]; // Do any additional setup after loading the view. self.delegate = self; [[UIDevice currentDevice] beginGeneratingDeviceOrientationNotifications]; [[NSNotificationCenter defaultCenter] addObserver:self selector:@selector(orientationChanged:) name:UIDeviceOrientationDidChangeNotification object:nil]; [[NSNotificationCenter defaultCenter] addObserver:self selector:@selector(measurementsSettingsUpdated:) name:@"MeasurementsSettingsUpdated" object:nil]; } - (void) measurementsSettingsUpdated:(NSNotification *) notification { // UINavigationController *navigationController = [self.viewControllers objectAtIndex:0]; // AddMeasurementViewController *addMeasurement = [[AddMeasurementViewController alloc] init]; // [navigationController setViewControllers: [[NSArray alloc] initWithObjects:addMeasurement, nil]]; resetWizardView = YES; } - (void) viewDidAppear:(BOOL)animated { if (![ReadPerson userHasRecords]) { [self setSelectedIndex:3]; } } - (void)orientationChanged:(NSNotification *)notification { // We must add a delay here, otherwise we'll swap in the new view // too quickly and we'll get an animation glitch [self performSelector:@selector(showGraphs) withObject:nil afterDelay:0]; } - (void)showGraphs { UIDeviceOrientation deviceOrientation = [UIDevice currentDevice].orientation; if (deviceOrientation == UIDeviceOrientationLandscapeLeft && !isShowingLandscapeView) { [self performSegueWithIdentifier: @"toGraph" sender: self]; isShowingLandscapeView = YES; } else if (deviceOrientation != UIDeviceOrientationLandscapeLeft && isShowingLandscapeView) { [self dismissModalViewControllerAnimated:YES]; isShowingLandscapeView = NO; } } - (void)viewDidUnload { [super viewDidUnload]; // Release any retained subviews of the main view. } - (void)dealloc { [[NSNotificationCenter defaultCenter] removeObserver:self]; [[UIDevice currentDevice] endGeneratingDeviceOrientationNotifications]; } - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { if(interfaceOrientation == UIInterfaceOrientationLandscapeRight) { [self performSegueWithIdentifier: @"toGraph" sender: self]; } return false; } - (void)tabBarController:(UITabBarController *)tabBarController didSelectViewController:(UIViewController *)viewController { int tbi = tabBarController.selectedIndex; if (tbi == 0) { [[viewController view] setNeedsDisplay]; if (resetWizardView) { [(UINavigationController*)[self.viewControllers objectAtIndex:0] popToRootViewControllerAnimated: NO]; // ******* POP CALLED HERE ****** resetWizardView = false; } } } - (TodaysMeasurementObject*) theAppDataObject { id<AppDelegateProtocol> theDelegate = (id<AppDelegateProtocol>) [UIApplication sharedApplication].delegate; TodaysMeasurementObject* theDataObject; theDataObject = (TodaysMeasurementObject*) theDelegate.theAppDataObject; return theDataObject; } - (BOOL)shouldAutorotate { return NO; } - (NSUInteger)supportedInterfaceOrientations { return UIInterfaceOrientationMaskPortrait; } @end UPDATED - (void) measurementsSettingsUpdated:(NSNotification *) notification { NSMutableArray *viewControllers = [[NSMutableArray alloc] initWithArray: self.viewControllers]; UINavigationController *navigationController = [viewControllers objectAtIndex:0]; AddMeasurementViewController *addMeasurement = [[AddMeasurementViewController alloc] init]; [navigationController setViewControllers: [[NSArray alloc] initWithObjects:addMeasurement, nil]]; [viewControllers setObject:navigationController atIndexedSubscript:0]; self.viewControllers = viewControllers; } and removed the code from - tabBarController:didSelectViewController: but still the same error. I think the problem is that it's trying to get a value for the slide control after the view has been deleted. But some part of the view must still be alive...? Anyway to kill that off? Or leave it all alive??

Read the article
PHP Email Form Sending Random Text

- by Doug

Hi, I did a webpage for a client that involved a series of text boxes asking for specific information such as a person's name, e-mail address, company, etc. Along with a button that would e-mail the information to my client. Whenever I tested the button it seemed to work perfectly, I uploaded the page and thought I was done. But, the other day my client got this email from the site: Name: rfhopzdgmx rfhopzdgmx Email: [email protected] Company: zUDXatAfoDvQrdH Mailing Address: AaSsXklqpHIsoCNcei gXsimMPRBYZqq vGLvZraZNdpOAV, ChsmuibE PoKzaSCubXPRI Home Phone: CIJbIfjMfjIaTqAlD Work Phone: JFLZBOvru Cell Phone: XlFJTTFGiTTiiFQfy Fax: UEJMOVZodWPkKxew Comments: sPvSCE hgetwoguderu,* [url=http://atyktjlxcznl.com/]atyktjlxcznl[/url], [link=http://nudvfcehwpyg.com/]nudvfcehwpyg[/link], http://lvvwkbzbhnzp.com/ Note: The * line contained HTML link code, I just don't know how to get this site to show it. Here is the PHP code in the site for the e-mail button. <?php //This Sends A Formatted Text Email Using The Text Boxes if ($_POST['submit']){ //This Gets The Form Data $fname = $_POST['fName']; $lname = $_POST['lName']; $email = $_POST['email']; $company = $_POST['co']; $address1 = $_POST['address1']; $address2 = $_POST['address2']; $city = $_POST['city']; $state = $_POST['state']; $zip = $_POST['zip']; $homep = $_POST['homeP']; $workp = $_POST['workP']; $cellp = $_POST['cellP']; $fax = $_POST['fax']; $comments = $_POST['txaOutputField']; //echo "<script language = 'javascript'>alert('YAY');</script>"; if ($fname && $lname && $email && $comments){ //Check If Required Fields Are Filled //This Sets The SMTP Configuration In php.ini ini_set("SMTP", "smtp.2ndsourcewire.com"); //This Replaces Any Blank Fields With 'None's if ($company == ""){ $company = "None"; } if ($address1 == ""){ $address1 = "None"; } if ($city == ""){ $city = "None"; } if ($state == ""){ $state = "None"; } if ($zip == ""){ $zip = "None"; } if ($homep == ""){ $homep = "None"; } if ($workp == ""){ $workp = "None"; } if ($cellp == ""){ $cellp = "None"; } if ($fax == ""){ $fax = "None"; } //This Creates The Variables Necessary For The Email $to = "CLIENT EMAIL WHICH I'M CENSORING"; $subject = "Email from 2ndSourceWire.com"; $from = "From: [email protected]"; $secondEmail = "MY EMAIL WHICH I'M ALSO CENSORING"; if ($address2 == ""){ $body = "Name: $fname $lname\n". "Email: $email\n". "Company: $company\n\n". "Mailing Address:\n". "$address1\n". "$city, $state $zip\n\n". "Home Phone: $homep\n". "Work Phone: $workp\n". "Cell Phone: $cellp\n". "Fax: $fax\n\n". "Comments:\n". "$comments"; } else { $body = "Name: $fname $lname\n". "Email: $email\n". "Company: $company\n\n". "Mailing Address:\n". "$address1\n". "$address2\n". "$city, $state $zip\n\n". "Home Phone: $homep\n". "Work Phone: $workp\n". "Cell Phone: $cellp\n". "Fax: $fax\n\n". "Comments:\n". "$comments"; } //This Sends The Email mail($to, $subject, $body, $from); mail($secondEmail, $subject, $body, $from); echo "<script language = 'javascript'>alert('The email was sent successfully.');</script>"; } else { //The Required Fields Are Not Filled echo "<script language = 'javascript'>alert('Please fill your first name, last name, email address, and your comment or question.');</script>"; } } ? I'm a little dumbfounded on how this happened, the client mentioned a couple e-mails of this, so I don't think it is a random glitch. Also, the e-mail address was formatted like an e-mail address, so someone or some program was interpreting the labels next to each text box. I also noticed that the first and last names entered are the same word, even though they were in different text boxes, I'm thinking its some spam program, but wouldn't they try to advertise something and make money, rather than just spouting out random text? Also, the comments section makes no sense to me at all, the links goto nowhere and they're all perfectly formatted, a random person just screwing around wouldn't know those tags, and a programmer doing it wouldn't bother with it, but also neither would a program. I have no idea what caused this or how to fix it, I'm drawing a blank here. Anyone have any ideas?

Read the article
a program similar to ls with some modifications

- by Bond

Hi, here is a simple puzzle I wanted to discuss. A C program to take directory name as command line argument and print last 3 directories and 3 files in all subdirectories without using api 'system' inside it. suppose directory bond0 contains bond1, di2, bond3, bond4, bond5 and my_file1, my_file2, my_file3, my_file4, my_file5, my_file6 and bond1 contains bond6 my_file7 my_file8 my_file9 my_file10 program should output - bond3, bond4, bond5, my_file4, my_file5, my_file6, bond6, my_file8, my_file9, my_file10 My code for the above problem is here #include<dirent.h> #include<unistd.h> #include<string.h> #include<sys/stat.h> #include<stdlib.h> #include<stdio.h> char *directs[20], *files[20]; int i = 0; int j = 0; int count = 0; void printdir(char *); int count_dirs(char *); int count_files(char *); int main() { char startdir[20]; printf("Scanning user directories\n"); scanf("%s", startdir); printdir(startdir); } void printdir(char *dir) { printf("printdir called %d directory is %s\n", ++count, dir); DIR *dp = opendir(dir); int nDirs, nFiles, nD, nF; nDirs = 0; nFiles = 0; nD = 0; nF = 0; if (dp) { struct dirent *entry = 0; struct stat statBuf; nDirs = count_dirs(dir); nFiles = count_files(dir); printf("The no of subdirectories in %s is %d \n", dir, nDirs); printf("The no of files in %s is %d \n", dir, nFiles); while ((entry = readdir(dp)) != 0) { if (strcmp(entry->d_name, ".") == 0 || strcmp(entry->d_name, "..") == 0) { continue; } char *filepath = malloc(strlen(dir) + strlen(entry->d_name) + 2); if (filepath) { sprintf(filepath, "%s/%s", dir, entry->d_name); if (lstat(filepath, &statBuf) != 0) { } if (S_ISDIR(statBuf.st_mode)) { nD++; if ((nDirs - nD) < 3) { printf("The directory is %s\n",entry->d_name); } } else { nF++; if ((nFiles - nF) < 3) { printf("The files are %s\n", entry->d_name); } //if } //else free(filepath); } //if(filepath) } //while while ((entry = readdir(dp)) != 0) { if (strcmp(entry->d_name, ".") == 0 || strcmp(entry->d_name, "..") == 0) { continue; } printf("In second while loop *entry=%s\n",entry->d_name); char *filepath = malloc(strlen(dir) + strlen(entry->d_name) + 2); if (filepath) { sprintf(filepath, "%s/%s", dir, entry->d_name); if (lstat(filepath, &statBuf) != 0) { } if (S_ISDIR(statBuf.st_mode)) { printdir(entry->d_name); } } //else free(filepath); } //2nd while closedir(dp); } else { fprintf(stderr, "Error, cannot open directory %s\n", dir); } } //printdir int count_dirs(char *dir) { DIR *dp = opendir(dir); int nD; nD = 0; if (dp) { struct dirent *entry = 0; struct stat statBuf; while ((entry = readdir(dp)) != 0) { if (strcmp(entry->d_name, ".") == 0 || strcmp(entry->d_name, "..") == 0) { continue; } char *filepath = malloc(strlen(dir) + strlen(entry->d_name) + 2); if (filepath) { sprintf(filepath, "%s/%s", dir, entry->d_name); if (lstat(filepath, &statBuf) != 0) { fprintf(stderr, "File Not found? %s\n", filepath); } if (S_ISDIR(statBuf.st_mode)) { nD++; } else { continue; } free(filepath); } } closedir(dp); } else { fprintf(stderr, "Error, cannot open directory %s\n", dir); } return nD; } int count_files(char *dir) { DIR *dp = opendir(dir); int nF; nF = 0; if (dp) { struct dirent *entry = 0; struct stat statBuf; while ((entry = readdir(dp)) != 0) { if (strcmp(entry->d_name, ".") == 0 || strcmp(entry->d_name, "..") == 0) { continue; } char *filepath = malloc(strlen(dir) + strlen(entry->d_name) + 2); if (filepath) { sprintf(filepath, "%s/%s", dir, entry->d_name); if (lstat(filepath, &statBuf) != 0) { fprintf(stderr, "File Not found? %s\n", filepath); } if (S_ISDIR(statBuf.st_mode)) { continue; } else { nF++; } free(filepath); } } closedir(dp); } else { fprintf(stderr, "Error, cannot open file %s\n", dir); } return nF; } The above code I wrote is a bit not functioning correctly can some one help me to understand the error which is coming.So that I improve it further.There seems to be some small glitch which is not clear to me right now.

Read the article
Phonegap / jquery mobile slide transition not workign properly on first call

- by Alexander Casassovici

I have an awkward visual glitch. I want nice transition when changing pages on the app. Unfortunately first time i change to another page, Instead of sliding current pagg out and new page in , current page is immediately replaces by the new page, then slides out... and when it's out of view it's the new page is shown... the second time around it works like a charm though !!! This is running on iphone with jquery mobile + phonegap I made a video to make the issue clear: http://www.youtube.com/watch?v=Ybvzh_wTnSE <body style="background-color: #000;"> <div id="container" style="display:none;"> <div id="side-menu" style="display:none;"> <div id="header_top"></div> <a href="#dives" onclick="showdives();"><div id="header_dives" class="selected"></div></a> <div id="header_spacer1"></div> <a href="#explore" onclick="showexplore();"><div id="header_explore"></div></a> <div id="header_spacer2"></div> <a href="#search" onclick="showsearch();"><div id="header_search"></div></a> <div id="header_spacer3"></div> <a href="#settings" onclick="showsettings();"><div id="header_settings"></div></a> <div id="header_bottom"></div> </div> <div id="slide_mask">  <div data-role="page" id="login"> <div id="home_frame"> <div id="home_logo"></div> <div id="home_fblogin" onclick="login()"></div> <div class="home_login"> <p>Email: <input type="text" name="user[email]" size="30"/></p> <p>Password: <input type="password" name="user[password]" size="30"/></p> <button onclick="show_page_home();">LOGIN</button> </div> </div> </div>   <div data-role="page" id="dives" class="right_pane"> <p>My dives !</p> </div> <div data-role="page" id="explore" class="hidden right_pane"> <p>My explore !</p> </div> <div data-role="page" id="search" class="hidden right_pane"> <p>My search !</p> </div> <div data-role="page" id="settings" class="hidden right_pane"> <p>My settings !</p> <button onclick="logout_db();">logout</button> </div>  </div> </div> <div id="log"></div> <div id="data"></div> </body> And the relevant CSS: body {margin: 0; font: 18px Helvetica; text-align: center; background-color: #000; background: url(../img/bg_big.png) repeat; -webkit-user-select: none; /* prevent copy paste for all elements */ } #container { width:320px; height:460px; overflow: hidden;} input{ -webkit-user-select: text; /* enable copy paste for elements with this class */} a {-webkit-user-select: none; /* prevent copy paste for all elements */} span {-webkit-user-select: none; /* prevent copy paste for all elements */} #side-menu {z-index: 1000 !important; position: fixed; height: 460px; width: 56.5px; background: url(../img/bg_big.png) no-repeat; display: inline-block; overflow: hidden; top: 0px; left: 0px; } #header_top {background: url(../img/header/header_top.png) no-repeat; background-size: 56.5px 48.96px; width: 56.5px; height: 48.96px; display: block;} #header_dives {background: url(../img/header/dives.png) no-repeat; background-size: 56.5px 51.75px; width: 56.5px; height: 51.75px; display: block;} #header_dives.selected{background: url(../img/header/dives_selected.png) no-repeat;} #header_spacer1{background: url(../img/header/header_space1.png) no-repeat; background-size: 56.5px 13.9px; width: 56.5px; height: 13.9px; display: block;} #header_explore{background: url(../img/header/explore.png) no-repeat; background-size: 56.5px 51.75px; width: 56.5px; height: 51.75px; display: block;} #header_explore.selected{background: url(../img/header/explore_selected.png) no-repeat;} #header_spacer2{background: url(../img/header/header_space2.png) no-repeat; background-size: 56.5px 15.33px; width: 56.5px; height: 15.33px; display: block;} #header_search{background: url(../img/header/search.png) no-repeat; background-size: 56.5px 51.75px; width: 56.5px; height: 51.75px; display: block;} #header_search.selected{background: url(../img/header/search_selected.png) no-repeat;} #header_spacer3{background: url(../img/header/header_space3.png) no-repeat; background-size: 56.5px 17.73px; width: 56.5px; height: 17.73px; display: block;} #header_settings{background: url(../img/header/settings.png) no-repeat; background-size: 56.5px 51.75px; width: 56.5px; height: 51.75px; display: block;} #header_settings.selected{background: url(../img/header/settings_selected.png) no-repeat;} #header_bottom{background: url(../img/header/header_bottom.png) no-repeat; background-size: 56.5px 160px; width: 56.5px; height: 160px; display: block;} .hidden {display: none;} .right_pane{width: 263.5px !important; background: url(../img/right_bg.png) no-repeat; background-size:263.5px 460px; width: 263.5px; height: 460px; left: 56.5px !important;} #slide_mask{ display: inline-block; overflow: hidden; padding-left: 56.5px; width: 263.5px; height: 460px; top: 0;} and the bit of JS: /////////////////////////////////// //MENU MECHANICS /////////////////////////////////// function showdives(){ $("#side-menu .selected").removeClass("selected"); $("#header_dives").addClass("selected"); } function showexplore(){ $("#side-menu .selected").removeClass("selected"); $("#header_explore").addClass("selected"); } function showsearch(){ $("#side-menu .selected").removeClass("selected"); $("#header_search").addClass("selected"); } function showsettings(){ $("#side-menu .selected").removeClass("selected"); $("#header_settings").addClass("selected"); } the onclick only add/remove the "selected" class to the menu items so... any hint ? been trying eveything for hours and still can't get it neat .. :(

Read the article
Problem with richfaces ajax datatable + buttons

- by Schyzotrop

Hello i have another problem with RichFaces this is my application and it shows how i want it to work : http://www.screencast.com/users/Schyzotrop/folders/Jing/media/a299dc1e-7a10-440e-8c39-96b1ec6e85a4 this is video of some glitch that i can't solve http://screencast.com/t/MDFiMGMzY the problem is that when i am trying to press any buttons on others than 1st category it won't do anything IF 1st category has less rows than the one i am calling it from from 1st category it works always i am using follwoing code in jsp for collumns : <h:form id="categoryAttributeList"> <rich:panel> <f:facet name="header"> <h:outputText value="Category Attribute List" /> </f:facet> <rich:dataTable id="table" value="#{categoryAttributeBean.allCategoryAttribute}" var="cat" width="100%" rows="10" columnClasses="col1,col2,col2,col3"> <f:facet name="header"> <rich:columnGroup> <h:column>Name</h:column> <h:column>Description</h:column> <h:column>Category</h:column> <h:column>Actions</h:column> </rich:columnGroup> </f:facet> <rich:column filterMethod="#{categoryAttributeFilteringBean.filterNames}"> <f:facet name="header"> <h:inputText value="#{categoryAttributeFilteringBean.filterNameValue}" id="input"> <a4j:support event="onkeyup" reRender="table , ds" ignoreDupResponses="true" requestDelay="700" oncomplete="setCaretToEnd(event);" /> </h:inputText> </f:facet> <h:outputText value="#{cat.name}" /> </rich:column> <rich:column filterMethod="#{categoryAttributeFilteringBean.filterDescriptions}"> <f:facet name="header"> <h:inputText value="#{categoryAttributeFilteringBean.filterDescriptionValue}" id="input2"> <a4j:support event="onkeyup" reRender="table , ds" ignoreDupResponses="true" requestDelay="700" oncomplete="setCaretToEnd(event);" /> </h:inputText> </f:facet> <h:outputText value="#{cat.description}" /> </rich:column> <rich:column filterMethod="#{categoryAttributeFilteringBean.filterCategories}"> <f:facet name="header"> <h:selectOneMenu value="#{categoryAttributeFilteringBean.filterCategoryValue}"> <f:selectItems value="#{categoryAttributeFilteringBean.categories}" /> <a4j:support event="onchange" reRender="table, ds" /> </h:selectOneMenu> </f:facet> <h:outputText value="#{cat.categoryID.name}" /> </rich:column> <h:column> <a4j:commandButton value="Edit" reRender="pnl" action="#{categoryAttributeBean.editCategoryAttributeSetup}"> <a4j:actionparam name="categoryAttributeID" value="#{cat.categoryAttributeID}" assignTo="#{categoryAttributeBean.id}" /> <a4j:actionparam name="state" value="edit" /> <a4j:actionparam name="editId" value="#{cat.categoryAttributeID}" /> </a4j:commandButton> <a4j:commandButton reRender="categoryAttributeList" value="Delete" action="#{categoryAttributeBean.deleteCategoryAttribute}"> <a4j:actionparam name="categoryAttributeID" value="#{cat.categoryAttributeID}" assignTo="#{categoryAttributeBean.id}" /> </a4j:commandButton> </h:column> <f:facet name="footer"> <rich:datascroller id="ds" renderIfSinglePage="false"></rich:datascroller> </f:facet> </rich:dataTable> <rich:panel id="msg"> <h:messages errorStyle="color:red" infoStyle="color:green"></h:messages> </rich:panel> </rich:panel> </h:form> and here is code of my backing bean @EJB private CategoryBeanLocal categoryBean; private CategoryAttribute categoryAttribute = new CategoryAttribute(); private ArrayList<SelectItem> categories = new ArrayList<SelectItem>(); private int id; private int categoryid; // Actions public void newCategoryAttribute() { categoryAttribute.setCategoryID(categoryBean.findCategoryByID(categoryid)); categoryBean.addCategoryAttribute(categoryAttribute); FacesContext.getCurrentInstance().addMessage("newCategoryAttribute", new FacesMessage("CategoryAttribute " + categoryAttribute.getName() + " created.")); this.categoryAttribute = new CategoryAttribute(); } public void editCategoryAttributeSetup() { categoryAttribute = categoryBean.findCategoryAttributeByID(id); } public void editCategoryAttribute() { categoryAttribute.setCategoryID(categoryBean.findCategoryByID(categoryid)); categoryBean.updateCategoryAttribute(categoryAttribute); FacesContext.getCurrentInstance().addMessage("newCategoryAttribute", new FacesMessage("CategoryAttribute " + categoryAttribute.getName() + " edited.")); this.categoryAttribute = new CategoryAttribute(); } public void deleteCategoryAttribute() { categoryAttribute = categoryBean.findCategoryAttributeByID(id); categoryBean.removeCategoryAttribute(categoryAttribute); FacesContext.getCurrentInstance().addMessage("categoryAttributeList", new FacesMessage("CategoryAttribute " + categoryAttribute.getName() + " deleted.")); this.categoryAttribute = new CategoryAttribute(); } // Getters public CategoryAttribute getCategoryAttribute() { return categoryAttribute; } public List<CategoryAttribute> getAllCategoryAttribute() { return categoryBean.findAllCategoryAttributes(); } public ArrayList<SelectItem> getCategories() { categories.clear(); List<Category> allCategory = categoryBean.findAllCategory(); Iterator it = allCategory.iterator(); while (it.hasNext()) { Category cat = (Category) it.next(); SelectItem select = new SelectItem(); select.setLabel(cat.getName()); select.setValue(cat.getCategoryID()); categories.add(select); } return categories; } public int getId() { return id; } public int getCategoryid() { return categoryid; } // Setters public void setCategoryAttribute(CategoryAttribute categoryAttribute) { this.categoryAttribute = categoryAttribute; } public void setId(int id) { this.id = id; } public void setCategoryid(int categoryid) { this.categoryid = categoryid; } and here is filtering bean : @EJB private CategoryBeanLocal categoryBean; private String filterNameValue = ""; private String filterDescriptionValue = ""; private int filterCategoryValue = 0; private ArrayList<SelectItem> categories = new ArrayList<SelectItem>(); public boolean filterNames(Object current) { CategoryAttribute currentName = (CategoryAttribute) current; if (filterNameValue.length() == 0) { return true; } if (currentName.getName().toLowerCase().contains(filterNameValue.toLowerCase())) { return true; } else { System.out.println("name"); return false; } } public boolean filterDescriptions(Object current) { CategoryAttribute currentDescription = (CategoryAttribute) current; if (filterDescriptionValue.length() == 0) { return true; } if (currentDescription.getDescription().toLowerCase().contains(filterDescriptionValue.toLowerCase())) { return true; } else { System.out.println("desc"); return false; } } public boolean filterCategories(Object current) { if (filterCategoryValue == 0) { getCategories(); filterCategoryValue = new Integer(categories.get(0).getValue().toString()); } CategoryAttribute currentCategory = (CategoryAttribute) current; if (currentCategory.getCategoryID().getCategoryID() == filterCategoryValue) { return true; } else { System.out.println(currentCategory.getCategoryID().getCategoryID() + "cate" + filterCategoryValue); return false; } } public ArrayList<SelectItem> getCategories() { categories.clear(); List<Category> allCategory = categoryBean.findAllCategory(); Iterator it = allCategory.iterator(); while (it.hasNext()) { Category cat = (Category) it.next(); SelectItem select = new SelectItem(); select.setLabel(cat.getName()); select.setValue(cat.getCategoryID()); categories.add(select); } return categories; } public String getFilterDescriptionValue() { return filterDescriptionValue; } public String getFilterNameValue() { return filterNameValue; } public int getFilterCategoryValue() { return filterCategoryValue; } public void setFilterDescriptionValue(String filterDescriptionValue) { this.filterDescriptionValue = filterDescriptionValue; } public void setFilterNameValue(String filterNameValue) { this.filterNameValue = filterNameValue; } public void setFilterCategoryValue(int filterCategoryValue) { this.filterCategoryValue = filterCategoryValue; } unfortunetly i can't even imagine what could cause this problem that's why i even made videos to help u understand my problem thanks for help!

Read the article

Search Results

Search found 199 results on 8 pages for 'glitch'.

Page 8/8 | < Previous Page | 4 5 6 7 8

- by George

- by Protheus

- by pinaldave

- by pinaldave

- by Vincent Grondin

- by Tarek

- by Dexter Morgan

- by daotoad

- by PrettyFlower

- by Roberts

- by FractalizeR

- by Padenton

- by AutoDMC

- by pinaldave

- by HellHarvest

- by Tim

- by askubuntu7639

- by David Rodríguez - dribeas

- by Lewis42

- by Doug

- by Bond

- by Alexander Casassovici

- by Schyzotrop

< Previous Page | 4 5 6 7 8