Search Results

Search found 22480 results on 900 pages for 'internet archive'.

Page 811/900 | < Previous Page | 807 808 809 810 811 812 813 814 815 816 817 818  | Next Page >

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• How to make a Windows Vista boot / recovery cd from a running system without using an original CD / DVD

  - by Giorgio

  I have just repaired a friends computer (replaced motherboard) and now I am trying to repair the Windows (Windows Vista) partitions. Unfortunately, probably due to the fact that he tried to start it several times after the old motherboard had stopped working (no signal on video) now the partition table or the file systems (or both?) appear to be damaged. I managed to boot Windows a couple of times but could not complete the boot. I tried to repair the partition table and file systems using Linux RIP (booting from USB stick) but the Linux utilities say that the file system is damaged and I should run chkdsk /f from Windows. So I now need a Windows boot CD from which I can boot and run chkdsk or any other Windows utilities that can repair the file system. Is there an easy way to create such a CD? Or can I download it for free somewhere? All the links to Windows Vista boot / repair CD's I have found on the internet refer to non-free stuff. Any hint? EDIT I have a working laptop with Windows Vista installed. So one solution would be to make a bootable CD or USB from it so that I can boot the desktop and run the repair utilities. However, I do not have the Windows Vista installation DVD, because both computers were bought with Windows pre-installed.

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• Family server setup [closed]

  - by Manny

  Hi all, I really hope some of you can give me some direction. I have setup a linux server at home and through samba I can access files from different computers in my home. I would like to use this server as a file-server for my family (brothers, sisters and parents who all live in their own homes). I really like the way it is set up right now with user and permission controls, but I've read that it is bad idea to open up the samba port to the world. The requirements are simple: 1) it should be easy to access, by using standard web browsers or mounting the drive (shouldn't have to use any VPN setup or use putty etc) 2) should be somewhat secure. We just want to share family pictures instead of putting them on facebook or picasa or other web server, nothing top secret. Here is what I've looked into: 1)Webdav. It seems decent but seems like it windows7 doesn't like it very much, even with digest mode authentication. User controls and permissions are not as flexible as samba (or at least to my knowledge). I really like the user and group permissions in samba, but if I could live with webdav if it worked seamlessly with windows, it should just work shouldn't it? 2) I read somewhere to stay away from ftp as it is outdated and that there are newer and better internet file-server setups? Was that a reference to webdav? I am so confused, please help... Manny

  Read the article

• Equivalent of scp -l bandwidth_cap for .ssh/config?

  - by Mark Bennett

  Short form: You can limit the bandwidth the scp uses with the -l switch, you pass a number that's in kbits/sec. I'd rather set this in my .ssh/config file for certain names machines. What's the equivalent named setting for -l ? I haven't been able to find it. Followup question: Generally, not sure how to map back and forth between ssh command line options and config names, short of doing Google searches or manually comparing man pages on a case by case basis. Is there a table that directly equates the two? Longer form of first question, with context: I've started using ssh config quite a bit, especially now that I need to go through a proxy and do lots of port mappings. I even define the same machine more than once depending on what type of tunneling I need. However, when uploading a large file, it's difficult to do anything else on my machine. Even though I have more download bandwidth than up, I think that scp saturates the link so even my small requests can't reach the Internet. There's a fix for this, using the -l bandwidth command line switch for scp. scp -l 1000 bigfile.zip titan: I'd like to use this in my config instead, so I'd create an additional named entry called "titan-upload" and I'd use that as the target whenever I upload. So instead of: scp bigfile.zip titan: I'd say: scp bigfile.zip titan-upload Or even set different caps depending on where I am: scp bigfile.zip titan-upload-from-home vs. scp bigfile.zip titan-upload-from-work I'm generally on Mac and Linux.

  Read the article

• C# sends SQL data 4 times less from one box than from another

  - by Bobb

  W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

  Read the article

• Cheap Solution for Routing a Toll Free Number to a Standard POTS Number

  - by VxJasonxV

  I do some technical work for an Internet Radio Show/Podcast, and need to fix something that has been broken for a while. The hosts have a Skype-In number to take listener calls, and for convenience sake, I bought and paid for a toll free number for a period of time. I used to use Asterlink for routing calls, but they folded and sent my number to OneBox, but they're ridiculously expensive by comparison. I'm looking for a cheap solution for this one simple task. Forward toll free calls to a skype-in number. The definition of cheap is as cheap or cheaper than Asterlink was. I paid something like $2 a month, and then the termination/call rate, which was a fraction of a sent for termination, and only whole cents after some serious time on the call. A $20 preload lasted me months at a time. I don't want to be upsold too, I want a simple web based management screen (CDR/stats are fun!), and obviously, it needs to be reliable. What vendors out there are you a fan of that solves this need?

  Read the article

• rpmbuild gives seg fault

  - by Deepti Jain

  I am trying to build an rpm using the rpmbuild tool. I have source code which build binaries around 30 GB. This software for which I am making the rpm has dozens of executables. When I copy only the binaries of a single executable (Eg. init) my rpm builds successfully. But when I dump the entire build to the rpm, rpmbuild does everything but gives a seg fault in the end. Here is my spec file: # This is a sample spec file for wget %define _topdir /root/mywget %define name source %define release 1 %define version 1.12 %define _builddir /root/mywget/BUILD/glenlivet %define _buildrootdir /root/mywget/BUILDROOT %define _buildroot /root/mywget/BUILDROOT %define _sourcedir /root/mywget/SOURCES BuildRoot: %{_buildroot} Summary: GNU source License: GPL Name: %{name} Version: %{version} Release: %{release} Source: %{name}-%{version}.tar.gz Prefix: /usr Group: Development/Tools %description The GNU sample program downloads files from the Internet using the command-line. %prep %setup -q -n glenlivet %build cd %{_builddir} make all %install rm -rf %{_buildrootdir} mkdir -p %{_buildrootdir}/bin cp -p -r %{_builddir}/build/obj-x64/* %{_buildrootdir}/bin/ %files %defattr(-,root,root) /bin/* If I only copy some of the binaries (let say one utility and its dependent binaries) it works fine. But when I try to copy the entire build, I get a seg fault. I get the seg fault after rpmbuild has executed these sections: %prep %build %install rpmbuild also processes my source file. Processing files: source-1.12-1 Finding Provides: Finding Requires: Finding Supplements: Provides:...... Requires:...... Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Segmentation fault Any clue what wrong is going on or where does rpmbuild fails? Thanks in advance

  Read the article

• vSphere Promiscuous mode only receiving packets one way from network switch

  - by steve.lippert

  We have two network switches, a POE switch (SwitchA) to power our phones / users computers and a non-POE switch (SwitchB for the rest network.) Each switch is setup to do port mirroring to support our VoIP recording system. SwitchA does port mirroring on specific ports if we need to record a user. SwitchB mirrors one port to monitor our work at home users (Internet comes in from managed router, to switch, back out to our firewall.) These two port mirroring setups feed into one vmware vSphere 4.1 server, it has four total physical cards. The other two NICs feed into an unmanaged switch for connecting to the rest of the network. Once into the vSphere server all network ports go into a vSwitch, and then one of the servers (Windows 2008 R2) sniffs them out and does its thing. Everything is working fine and dandy from SwitchB. But on SwitchA we only receive one side of the VoIP packets (going out to the phone, nothing coming in from the phone). Troubleshooting steps I have taken so far: I hooked up my laptop to the monitor port on SwitchB and I see both sides of the packets. I swapped which network interface is plugged into the monitor port on SwitchA. Because everything feeds into one vSwitch / vNetwork and both sides of the conversation arrive just fine from SwitchB I believe everything is configured correctly on the vSphere server/guest. What could be causing one way packets to arrive on my guest machine from only one interface, but not the other? Could a bad cable be causing the problems from SwitchB?

  Read the article

• Update in grub.cfg file for loading new kernel image in Ubuntu 11.04

  - by user1627657

  I am new to Linux. I am compiling Linux kernel (ver: 2.6.34.12) in gcc in traditional manner in VMware machine in Ubuntu (kernel version - 2.6.38-8-generic) 11.04 version. I am unable to find, where to update about newly compiled kernel in the grub.cfg file. I updated the newly created image version name in the existing image. Then VMware didn't able to load new kernel. I have searched in internet but I didn't find. So anyone can help me, to update in the grub.cfg and to successfully load new kernel. Few things about what I have done: Make bzImage to create image file. Make modules_install && make install to install modules and then sudo mkinitramfs -o initramfs.img-2.6.34 2.6.34. Then sudo gedit grub.cfg. In that at the mementry I updated the version of vmlinuz and initrd from 2.6.38-8 to 2.6.34.12. This is I have done.

  Read the article

• Remote Desktop fails after VPN connection

  - by Samet Sorgut

  The local computer (comp 1) is connected to a remote computer (comp 2) with Remote Desktop. On the remote computer (comp 2), I try to establish an VPN connection to a different remote computer (comp 3). Once I try to establish the VPN connection from the remote computer (comp 2) to the second remote computer (comp 3), Remote Desktop freezes on comp 1. It is not possible to connect to comp 2 again via Remote Desktop. What can be done to connect to this remote computer (comp 2) after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest? EDIT: I want to use the internet connection of the VPN, so all traffic should go over the VPN but still RDP working. My IP: 100.0.0.1 The IP where I'm connecting via RDP: 200.0.0.20 (Mask: 255.255.255.192, Gateway: 200.0.0.193) Where the 200.0.0.1 connects to VPN the IP of the VPN is: 65.254.61.250 Will routing like this help (Command is issued in 200.0.0.20, the RDP location): route ADD 65.254.61.250 MASK 255.255.255.192 200.0.0.193 Couldn't add gives the error: The route addition failed: The parameter is incorrect. I tried before connecting to VPN.

  Read the article

• Router vs switch in a LAN [closed]

  - by servernewbie

  If I have a LAN and and connect it with a switch, I understand it uses a CAM table to route packets in layer 2 (by saving mac to port relations). So far all good. However, when using a router for a LAN (ONLY for a LAN, not to connect it to "the outside" WAN/internet/etc) I get a bit confused as to how it internally processes packets. I would first split this into two router scenarios: Router with buit-in switch In this scenario, I would expect that it will act exactly as a switch with a CAM table internally. This would probably benefit a bit in speed (guessing here?) compared to the next option. Router without built-in switch Here is where I get confused. If hostA wants to send a packet to hostB, it will ARP to find hostB's MAC address and send it there. Now, if we had a switch (above scenario) this would be easy. But how does it work now in a router WITHOUT a switch? If I would guess, hostA would send an Ethernet frame with hostB's MAC address to the line. The router would fetch the packet (even though the router has another MAC address, it would still fetch this packet even if it only contains hostB's MAC address). It would strip the Ethernet frame header and check the IP, and then check its own internal ARP table again for the MAC address. Now, this would seem like a waste of resources compared to a router with a built-in switch. But maybe it does not work like that at all. Does it also contain a CAM table? If that would be true, what would then the difference between these two routers really be?

  Read the article

• Apache returns HTTP 206 for GET /file.mp3

  - by javano

  I am making a get request to an SSL enabled site on apache (so wireshark isn't giving me anything to useful). In my Apache SSL access log I see the following entry: 1.2.3.4 - my.username [15/Nov/2012:16:52:01 +0000] "GET /uploads/file.mp3 HTTP/1.1" 206 534400 "https://site.com/uploads/layla.mp3" "Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/535.19 (KHTML, like Gecko) Ubuntu/12.04 Chromium/18.0.1025.168 Chrome/18.0.1025.168 Safari/535.19" Why is this happening? I'm not familiar with the HTTP 206 response code but searching the Internet I can see it is a partial content GET requests. I understand correctly, my browser is making a partial GET request not for the full file. Is that correct? If so, is this a browser issue or is the web server instructing my browser to do so? I have tested in Firefox also and in both browser, I am not sent the file. If I rename the file to file.jpg I can download it through my browser and rename it to .mp3 and it plays. How can I troubleshoot this issue?

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• use ssh tunnel with phpmyadmin

  - by JohnMerlino

  I been using ssh tunnel to bypass firewall of remote mysql server. On my Ubuntu 12.04 installation, it works via the terminal and it works when using a program called mysql workbench. However, that program freezes often and I want to try phpmyadmin as an alternative. However, I cannot connect to remote server using ssh tunnel on phpmyadmin, albeit I can connect locally. These are the steps I've tried: 1) Open a tunnel, listening on localhost:3307 and forwarding everything to xxx.xxx.xxx.xxx:3306 (used 3307 because MySQL on my local machine uses the default port 3306): ssh -L 3307:localhost:3306 [email protected] So now I have the port for tunnel open and I have my local mysql installation default port: $ netstat -tln Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3307 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN ... 2) Now I can easily connect to remote server via localhost using the terminal: $ mysql -u user.name -p -h 127.0.0.1 -P 3307 Notice that I expicitly identify 3307 as the port, so traffic forwards to the remote server, and hence it logs me in to the remote server. Unfortunately, the localhost/phpmyadmin local login interface doesn't allow you to specify a port option. So I modify the config-db.php file and change the $dbport variable to 3307, under the impression that the phpmyadmin interface will now work with port 3307: $ sudo vim /etc/phpmyadmin/config-db.php $dbport='3307'; Then I restart the mysql server. Unfortunately, it didn't work. When I use the remote credentials to login, it gives me error: #1045 Cannot log in to the MySQL server

  Read the article

• How to prevent eMule from jamming up the router?

  - by the searcher

  Usually, when eMule is started, after some time, I find that the router is jammed, so the internet connection on that computer stopped working, or it seemed to be waiting for some port to be freed up before it can connect to a website. This sometimes affect even other PCs or Macs using the same router. Is there a way to prevent eMule from hogging too much resource or ports? I see that there is under Options -> Connection "Max Sources/File" and a "Connection Limits - Maximum Connections". Right now I set them to really low numbers: the first to 120 and the second to 200, but what are good numbers to fill in there so that it can work well without jamming up the router or use up the network resource of the PC or Mac? Or could it be that the number of files that are "Waiting" is too high, and used up too much resource? (If so, can emule automatically limit the number to 10 or 20 to prevent using too much resource?) (This happened before on Linksys router, Netgear router, and the AT&T U-verse router.)

  Read the article

• Host Name Resolution - ISA 2006 - VPN PPTP

  - by Brian Lee Jackson

  We are running an ISA 2006 server and PPTP VPN connection works fine. Clients are able to connect to internet, access Outlook, CRM, etc. The problem we are encountering is that host name resolution is not working. Example, when connected via VPN I can’t ping any box other than the VPN server by the host name. Nslookup also fails. I can ping everything fine via IP address. But for clients, they need to be able to access their “mapped” drives over the VPN which all are mapped by host name. I recently took over this position and it sounds like this used to work. What would be the best place to check first? I haven’t had much exposure to ISA and have been reading up a bit on installation procedures, etc. DNS is hosted and running on our domain controller, as well as WINS. It isn’t on the ISA box. Is there a firewall policy that perhaps got removed? What usually is required for host name resolution to pass through. Any help would be appreciated, thanks!

  Read the article

• Hearing a clicking noise from soundcard all the time

  - by Mehrdad

  I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

  Read the article

• Computer won't start after installing new video card

  - by Vercas

  So, 1 year and 340 days ago I bought a desktop computer. Since then, it has served me well. But lately, I wanted an upgrade, so I bought a new video card. I documented myself about the compatibility, and it is okay. So I opened the case, cleaned up that... dust elemental living inside of it. Unscrewed the plastic thingie on the outside to unscrew the old video card. Because of the stupid arrangement of the ports, I had to unscrew the motherboard to unplug it. So I unscrewed it, removed the old card, put in the new one, moved the motherboard back, screwed it back in, screwed the video card on the holder... thingie, and screwed the plastic thingie back in. Everything went smoothly, nothing had to be forced in/out. I connected the external power supply, closed the computer case, put the tower back in it's place and all the cables back in. When I pressed the power button, the LED turned... some color I can't distinguish. It stayed that way for a second, and then it went off. I tried a bunch of things, including permuting the external power supply arrangement (1 connection, 2 connections and no connections), with no success. And here are some of the specifications: Motherboard manufacturer: Asrock Processor: AMD Athlon II X2 3.0 GHz RAM: 2 x 2GB (had only 1 initially, bought the second plate a bit later) OLD video card: AMD Radeon HD 5450 NEW video card: Gigabyte nVidia GeForce GTX 650 GPU, 1GB GDDR5 128bit PCI-E, Dual-link DVI-Dx2 / HDMI / D-Sub Power supply: 450W + all the requirements I managed to find on the internet are met (+12V 18A or something) More specific information is stored... On that computer. If required, I may open the case again and read the stickers to find more specific information. I can also provide photos if necessary. Any ideas? Suggestions? Something? :|

  Read the article

• Why can't I debug my ASP project through a remote desktop connection?

  - by Anthony Benavente

  I just asked this question in Stack Overflow but I figured this stack exchange forum is a better fit. It's been about a month of trying to figure out this problem and we've still not found a solution. We have about seven virtual machines on a server running Windows XP Professional w/ SP 3 all with Visual Studio Interdev and IIS 5.1 installed. Running the programs all work fine, but we just can't debug through remote desktop. When we are logged into the server console (through VM Sphere) and log into one of the virtual machines through there, we are able to debug properly. We figured the issue lies with some kind of permissions for Remote Desktop Users. We've tried nearly every article on the internet (exaggerating of course) and are about to give up hope. One more thing, when we are logged into the virtual machine through the server console and then remote in, the user that was logged into the console is kicked off but debugging works! Does remoting in trick the computer into giving us the correct permissions? I'm really not sure how it works. I know that this technology predates human history, but we are in the process of migrating from ASP Classic to ASP.NET Specs: - Windows XP Professional W/ SP3 - IIS 5.1 - Visual Studio 6 Interdev EDIT: By "debug" I mean running the project with breakpoints. Interdev doesn't stop at breakpoints.

  Read the article

• Frequent freezes with constant disk activity on SSD netbook

  - by SamsLembas

  I am running Arch Linux on an HP Mini 1000 with a SSD. The machine is a little under a year old and fairly heavily used. About a month ago the machine started freezing up. During the freezes, the system is almost completely unresponsive, seemingly especially for disk-intensive tasks such as launching an application for the first time since reboot. The disk activity led is always constantly illuminated during the freezes. After somewhere between 30 sec and 3 minutes, the machine returns to normal operation. I am pretty sure that the SSD is the source or the problem. Iotop reports a disk transfer rate of 0 during the freezes, so I think it must be getting "stuck" and simply not performing any r/w during the time. I can't seem to find any information on these symptoms on the Internet, so any input on exactly what might be the cause of this would be greatly appreciated. The machine is under warranty, but I would rather not deal with HP until I actually know what is going on. Thanks.

  Read the article

• Exchange 2010 - Certificate error on internal Outlook 2013 connections

  - by Lorenz Meyer

  I have an Exchange 2010 and Outlook 2003. The exchange server has a wildcard SSL certificate installed *.domain.com, (for use with autodiscover.domain.com and mail.domain.com). The local fqdn of the Exchange server is exch.domain.local. With this configuration there is no problem. Now I started upgrading all Outlook 2003 to Outlook 2013, and I start to get consistently a certificate error in Outlook : The Name on the security certificate is invalid or does not match the name of the site I understand why I get that error: Outlook 2013 is connecting to exch.domain.local while the certificate is for *.domain.com. I was ready to buy a SAN (Subject Alternate Names) Certificate, that contains the three domains exch.domain.local, mail.domain.com, autodiscover.domain.com. But there is a hindrance: the certificate provider (in my case Godaddy) requires that the domain is validated as being our property. Now it is not possible for an internal domain that is not accessible from the internet. So this turns out not to be an option. Create self-signed SAN certificate with an Enterprise CA is an other option that is barely viable: There would be certificate error with every access to webmail, and I had to install the certificate on all Outlook clients. What is a recommended viable solution ? Is it possible to disable certificate checking in Outlook ? Or how could I change the Exchange server configuration so that the public domain name is used for all connections ? Or is there another solution I'm not thinking of ? Any advice is welcome.

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

< Previous Page | 807 808 809 810 811 812 813 814 815 816 817 818  | Next Page >