Search Results

Search found 26114 results on 1045 pages for 'zend config xml'.

Page 814/1045 | < Previous Page | 810 811 812 813 814 815 816 817 818 819 820 821  | Next Page >

• Centos VM serving multiple public IP: how to configure network interface?

  - by Glasnhost

  I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• PXELinux and compressed kernels/images

  - by Yvan JANSSENS

  Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

  Read the article

• PassEnv does not find ENV variables

  - by quodlibetor

  I've got this /etc/profile.d/myfile.sh: export MYVAR=myval I also have a PassEnv MYVAR line in a <virtualhost> section of an apache conf dir. That lets me do things like: $ echo $MYVAR myval $ python >>> import os; os.getenv('MYVAR') 'myval' $ sudo echo $MYVAR myval $ sudo -i root# echo $MYVAR myval But then, despite that being the case I get: root# /sbin/service httpd restart /sbin/service httpd restart Stopping httpd: [ OK ] Starting httpd: [Mon Oct 22 14:44:02 2012] [warn] PassEnv variable MYVAR was undefined [ OK ] And all of my attempts to access MYVAR from within my wsgi scripts just don't work. Thoughts? Am I doing something obviously wrong? EDIT for more detail I've got a swarm of computers/VMs and a swarm of developers working on a swarm of projects. I need a simple central place to keep environment information, the most common is the "environment" (dev/stage/prod). The scheme that we've got (modifying *.wsgi programmatically) is turning out to be more fragile than we'd like. The main options that I see are: put things in the shell environment put things in other config files Getting things into the shell environment is the best, because we won't need to write yet more duplicated "what is my environment" code.

  Read the article

• Skipping nginx PHP cache for certain areas of a site?

  - by DisgruntledGoat

  I have just set up a new server with nginx (which I am new to) and PHP. On my site there are essentially 3 different types of files: static content like CSS, JS, and some images (most images are on an external CDN) main PHP/MySQL database-driven website which essentially acts like a static site dynamic PHP/MySQL forum It is my understanding from this question and this page that the static files need no special treatment and will be served as fast as possible. I followed the answer from the above question to set up caching for PHP files and now I have a config like this: location ~ \.php$ { try_files $uri =404; fastcgi_cache one; fastcgi_cache_key $scheme$host$request_uri; fastcgi_cache_valid 200 302 304 30m; fastcgi_cache_valid 301 1h; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/php-fastcgi/php-fastcgi.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/example$fastcgi_script_name; fastcgi_param HTTPS off; } However, now I want to prevent caching on the forum (either for everyone or only for logged-in users - haven't checked if the latter is feasible with the forum software). I've heard that "if is evil" inside location blocks, so I am unsure how to proceed. With the if inside the location block I would probably add this in the middle: if ($request_uri ~* "^/forum/") { fastcgi_cache_bypass 1; } # or possible this, if I'm able to cache pages for anonymous visitors if ($request_uri ~* "^/forum/" && $http_cookie ~* "loggedincookie") { fastcgi_cache_bypass 1; } Will that work fine, or is there a better way to achieve this?

  Read the article

• How should I configure backup of my server?

  - by ed209

  I have just rented a dedicated server. If it helps this is the config I have: CPU1 Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (Cores 8) RAM 15975 MB Disk /dev/sda doesn't contain a valid partition table (=> /dev/sda doesn't) Disk /dev/sdc doesn't contain a valid partition table (=> /dev/sdc doesn't) Disk /dev/sdb doesn't contain a valid partition table (=> /dev/sdb doesn't) Disk /dev/sda: 120.0 GB (=> 114 GIB) Disk /dev/sdc: 3000.6 GB (=> 2861 GIB) Disk /dev/sdb: 3000.6 GB (=> 2861 GIB) /dev/sda is a 120GB SSD. This is where I have Ubuntu/lamp installed. It's the drive that will run my site. With the account I got two other drives of 3000GB each which I really don't need but they came with the account. I figured I could use these to back up my main 120gb drive. So a couple of things I wondered were: Should I use these for backups? How should I back up. The data I want to back up is a user uploads directory full of images and the database. Everything else is either in a code repo or backed up some other way. For example, it would be nice to know there is a disk image of the 120gb drive somewhere that I can copy over should there be any problems but equally I don't mind doing a fresh install of all the software and copying over just the images and database dump. Thanks for your advice! (also, happy to not use the two other drives and backup elsewhere if it's more sensible)

  Read the article

• sub application and virtual directory file permissions

  - by Zeus

  I have a website setup in IIS7, exampledomain.com. Under the application exampledomain.com lives a sub application cms. In a rather convoluted way, we have content in our cms system in this sub-app, under cms\content\{generatedfoldername}. So to access an image in this content, the full URL would be http://www.exampledomain.com/cms/cms/content/{generatedfoldername}/image.jpg, (yes, cms twice...) and this works just fine. Now, we have a virtual directory under the parent website, called stuff which points at the content of the cms. So I should be able to get to the image using the url http://www.exampledomain.com/stuff/{generatedfoldername}/image.jpg. Unfortunately this gives a server 500 error "There is a problem with the resource you are looking for, and it cannot be displayed." Whilst you do have to log into the cms system to access any of the admin pages within, I don't think the image files are protected by login, or else the first example URL wouldn't work, right? Also it's a server 500 error, rather than a 403. I'm sure I must be missing something obvious here- will the virtual directory be using the permissions defined in the parent application, or the subapplication to which it is pointing? Or is there some other permissions I may have missed? Sorry, that was a bit long, thanks for reading all the way down here! (I also must point out that I'm pretty new to the server management stuff.) edit: also, we have <location path="." inheritInChildApplications="false"> specified in the webconfig of the parent app, so it's hopefully not the issue described in this config file hierarchy article.

  Read the article

• D-Link wireless router losing outbound data

  - by gsteinert

  I have a Linux box running the Apache web server behind a D-Link wireless router (nothing fancy, just standard kit that comes with Virgin Media broadband). My issue is that when requesting web pages (from within the network or via the web), the back end of the page seems to be being dropped. For example, I tried to display a text-only file, and all I could get was the first 40-70% of the file (it changed slightly with each refresh). The apache access logs show that only part of the data was being sent (~6000 bytes instead of the 12000+ bytes of the file). Removing my router from the equation fixes the issue and I can download any files no matter the size with no problems. My theory is that the uploaded packets are either being dropped or held up by the config of the router. Is there anything I can do to alleviate the problem? (Perhaps a way of reconfiguring the router to upload packets harder/better/faster/stronger or an option in apache that provides a workaround) As a last resort I will get a second NIC for my Linux box and turn it into a router, but that would mean the box will be on 24/7... not the most ideal of circumstances. Gary

  Read the article

• MySQL Tables Missing/Corrupt After Recreation

  - by Synetech inc.

  Hi, Yesterday I dumped my MySQL databases to an SQL file and renamed the ibdata1 file. I then recreated it and imported the SQL file and moved the new ibdata1 file to my MySQL data directory, deleting the old one. I’ve done it before without issue, however this time something is not right. When I examine the (personal, not MySQL config) databases, they are all there, but they are empty… sort of. The data directory still has the .ibd files with the correct content in them and I can view the table list in the databases, but not the tables themselves. (I have file-per-table enabled, and am using InnoDB as default for everything.) For example with the urls database and its urls table, I can successfully open mysql.exe or phpMyAdmin and use urls;. I can even show tables; to see the expected table, but then when I try to describe urls; or select * from urls;, it complains that the table does not exist (even though it just listed it). (The MySQL Administrator lists the databases, but does not even list the tables, it indicates that the dbs are completely empty.) The problem now is that I have already deleted the SQL file (and cannot recover it even after scouring my hard-drive). So I am trying to figure out a way to repair these databases/tables. I can’t use the table repair function since it complains that the table does not exist, and I can’t dump them because again, it complains that the tables don’t exist. Like I’ve said, the data itself is still present in the .ibd files and the table names are present. I just need a way to get MySQL to recognize that the tables exist in the databases (I can find the column names of the tables in question in the ibdata1 file using a hex-editor). Any idea how I can repair this type of corruption? I don’t mind rolling up my sleeves, digging in, and taking a bunch of steps to fix it. Thanks a lot.

  Read the article

• Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

  - by Brandon Bearden

  Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

  Read the article

• Puppet: is it ok to "force" certname when you expect to shuffle nodes around?

  - by Luke404

  We all know (good example on SF) that Puppet hostname detection could be... fun. At our company (and I guess we're not alone at this) we usually pre-configure servers at our offices and test them before bringing the gear to a remote datacenter and rack them. Of course the reverse dns will change when doing that, even if we don't change the actual hostname of the system. We're slowly drafting our puppet setup and I'd like to be sure those moves won't create problems. My idea is to explicitly configure the desired full FQDN of the system as certname in puppet.conf at server provision time (before the very first puppet run). My process would look something like this: basic o.s. installation basic network configuration, enough to reach the internet and resolve dns install puppet and set up certname start puppet and let him manage the whole configuration test, fix problems in config (via puppet), re-test, and so on... manually stop puppet set up new network configuration for the datacenter network move the machine to DC turn it on puppet should automatically start and keep on doing its job The process is supported by detecting the environment in puppet's manifests (eg. based on subnet, like they do at Wikimedia) and modify configuration as needed (eg. resolv.conf contents appropriate for each network). Each node's certname will never change for the whole system life cycle. Is there any problem with this approach? Could it be improved?

  Read the article

• Join Domain from VM

  - by Adis

  I have two VMs running on VMWare Player. I use NAT adapter settings. The host machine for VMs is running on corporate network. First VM has Domain controller running and I can log in on that machine using domain credentials. I named domain wm.local When I run IP config on this machine: IP: 192.168.87.132 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 Second VM cannot join domain. When I try it with domain WM I'm propmted for credentials. And I enter Administrator credentials and than it waits for some time and I get response: "The specified domain either does not exist or could not be contacted" If i type wm.local as domain when trying to join it does not prompt me to login but just shows "An Active Directory Domain Controller (AD DC) for the domain wm.local could not be contacted. And here it takes no time to get this error message. Ipconfig on this machine: IP: 192.168.87.134 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 I can ping second VM from first one. And I disabled firewalls on both machines. Any ideas? Is there any manual for this?

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• Access an external SSH server through a restrictive proxy [on hold]

  - by Cyrille

  I'm a software developer. I wish to access my computer at home through SSH. For example, I sometime need to access my personal projects source code to check how I handled specific problems. Unfortunately, I currently work under an over-restrictive and anti-productive proxy that waste a hell of a lot of everyone's time (We often have to visit websites from our smartphones or use a web proxy to check very legitimates websites for answers, and don't get me started on other "security" overkill features we have to cope with...). Well, back to the subject, I can access my home computer from my phone (SSH, port 22 and 80 both redirected by router on port 22). It works, but it's quite uncomfortable. From my office computer, this is what I tried so far: export http_proxy=http://user:pass@proxyip:8080 echo "user:pass" > ~/.corkscrew-auth echo "ProxyCommand corkscrew proxyip 8080 %h %p /home/me/.corkscrew-auth" > ~/.ssh/config ssh 82.23.34.56 -l me -p 80 Proxy could not open connnection to 82.23.34.56: Forbidden ssh_exchange_identification: Connection closed by remote host (same without -p 80) Without corkscrew: ssh: connect to host 82.23.34.56 port 80: Connection timed out ssh: connect to host 82.23.34.56 port 22: Connection timed out Any other idea ?

  Read the article

• Why is there an extra HDD under /dev being added in my Linux Kernel?

  - by user1279156

  I have created a Linux kernel and for some reason an extra drive is always added at bootup. My hard drive is listed as /dev/sdb. /dev/sda is created too, and it is 8 MB in size. I can't find anything in the kernel config that is creating this, but if I use a different kernel it is not there. Kernel logs show it as an attached SCSI device, looks just like my hard drive but only 8 MB, and has no partition table. It also doesn't appear to be a physical device. I've tried the kernel on many different models of PCs and it is always there. Does anyone know how to remove it? /dev/disk/by-id gives me: scsi-1AMCC_U21413034D98EB000584 scsi-1AMCC_U21413034D98EB000584-part1 scsi-353333330000007d0 scsi-SATA_ST3250312AS_5VY7SH42 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part1 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part2 hdparm -i /dev/sda gives me an "invalid argument". dd if=/dev/sda of=sda.img the resulting file does not have any content sdparm results: /dev/sda: Linux scsi_debug 0004 Device identification VPD page: Addressed logical unit: designator type: T10 vendor identification, code set: ASCII vendor id: Linux vendor specific: scsi_debug 2000 designator type: NAA, code set: Binary 0x53333330000007d0 Target port: designator type: Relative target port, code set: Binary transport: Serial Attached SCSI (SAS) Relative target port: 0x1 designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007ce designator type: Target port group, code set: Binary transport: Serial Attached SCSI (SAS) Target port group: 0x100 Target device that contains addressed lu: designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007cd designator type: SCSI name string, code set: UTF-8 transport: Serial Attached SCSI (SAS) SCSI name string: naa.52222220000007CD

  Read the article

• error 503: Can't deploy rails 3 app with apache + thin (bitnamy ruby stack)

  - by Pacu

  As you'll notice, I'm a bit of a noob on Rails. Here's the thing I have a EC2 Bitnami RubyStack AMI running. I'm trying to deploy the sample project to be sure I'm doing the right thing, but I'm not getting anywhere at all. I just get a 503 error I'm following bitnami's docs on thin + apache Here are my files: the httpd.conf I include in the main httpd.conf Alias /sample "/home/bitnami/stack/projects/sample/public" <Directory "/home/bitnami/stack/projects/sample/public"> AllowOverride None Order allow,deny Allow from all </Directory> ProxyPass /sample balancer://appcluster ProxyPassReverse /sample balancer://appcluster <Proxy balancer://appcluster> BalancerMember http://127.0.0.1:3001/sample BalancerMember http://127.0.0.1:3002/sample BalancerMember http://127.0.0.1:3003/sample BalancerMember http://127.0.0.1:3004/sample </Proxy> the thin.yml file chdir: /opt/bitnami/projects/sample environment: production address: 127.0.0.1 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 512 require: [] wait: 30 servers: 5 prefix: /sample daemonize: true I'm able to start and stop apache, but thin does not stop correctly though. When I try to stop thin, I get this output /opt/bitnami/projects/sample$ sudo thin -C config/thin.yml stop Stopping server on 127.0.0.1:3000 ... Can't stop process, no PID found in tmp/pids/thin.3000.pid Stopping server on 127.0.0.1:3001 ... Can't stop process, no PID found in tmp/pids/thin.3001.pid Stopping server on 127.0.0.1:3002 ... Can't stop process, no PID found in tmp/pids/thin.3002.pid Stopping server on 127.0.0.1:3003 ... Can't stop process, no PID found in tmp/pids/thin.3003.pid Stopping server on 127.0.0.1:3004 ... Can't stop process, no PID found in tmp/pids/thin.3004.pid I've tried to use nginx as well, without any luck unfortunately. Thank you for your time and help!

  Read the article

• Can anyone help me make my reverse proxy actually cache?

  - by Lenary

  Hi folks, I'm trying to configure a Reverse Caching Proxy but so far have had no luck. I would preferrably like to use apache (that will be all it will be used for), but am open to solutions using other software that can also run on Mac OS X 10.6 (I have also tried using Varnish and Squid, but with no more luck). We're running a system with about 80 mac mini clients that will be requesting lots of video from a server. To reduce load, we thought we could use Apache (which comes on the macs by default) to cache this video forever (or at least as long as possible) onto the macs' disks. I have managed to get a reverse proxy set up with apache using ProxyPass etc, but when i tried to add CacheEnable disk / to the configuration, nothing happened (i do have mod_disk_cache included). Can anyone help with my issue? The apache config file is here Thanks in advance Edit: So far I have been testing it with smaller text files, and it hasn't been caching properly. This suggests it is nothing to do with us actually downloading video, but actually to do with the cache configuration.

  Read the article

• How to set up a server without a hosting control panel

  - by A4J

  I have always used a control panel on my dedicated servers - from cPanel to Plesk to Virtualmin, and I am now considering ditching a CP altogether and manually editing config files. My requirements are fairly simple, I will host multiple sites on the server; some Apache with PHP & Mysql and some Passenger with Rails & Postgres. All will require email smtp/pop. FTP/Stats will not be required. Could someone please give me a quick run-down of what I would need to do - in terms of installing software and configuration? My server will come with a base install of CentOS 6.4 minimal. My thoughts so far: Install/update latest versions of MySQL & Postgres (are they 'safe' out of the box? Or do I need to do anything else like set up root passwords etc?) Install Apache & PHP (again, are the base installs good to go or do they require security tweaks?) Set up nameservers/hostnames/reverse DNS etc (Any guides on how to do this please?) Install Rubygems Install and configure Dovecot and Postfix (any tips on doing this? Or links to how-tos that cover it please?) Set up each website - any links to guides on how to do this? Install/configure firewall (or is the default install good to go?) Any other tips or advice would be greatly appreciated, as would links to guides or how-tos.

  Read the article

• Empty $upstream_http_location variable if response was cached

  - by Ivaldi

  I would like to cache the response of an redirect. (Cache the request to some site which returns a redirect and cache the second request which returns the actual content.) So far my config looks like this: location = /proxy { error_page 301 302 307 = @redir; resolver 8.8.8.8; proxy_pass $arg_url; proxy_intercept_errors on; proxy_cache pcache; proxy_cache_key $arg_url; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_client_abort on; proxy_ignore_headers Set-Cookie Expires Cache-Control; } location @redir { resolver 8.8.8.8; # we need to assign $upstream_http_location to another var in order to use it with proxy_pass set $target $upstream_http_location; proxy_pass $target; proxy_cache predirects; proxy_cache_key $upstream_http_location; proxy_cache_valid 200 301 302 307 1d; proxy_cache_min_uses 1; proxy_ignore_headers Set-Cookie Expires Cache-Control; } It works for the first request or without the 30x codes for proxy_cache_valid in the /proxy part, but $target and $upstream_http_location are empty, if the response was cached. Is there a nice solution to cache both requests? Thanks!

  Read the article

• Hardware testing tool/suite

  - by Aviator

  Hi All, I just bought a new core i5 system (assembled) and started installing Windows 7. It was failing for many times and at some point got installed. After that, frequent crashes related to MEMORY. So checked the RAM using memtest86+ and found many errors.I got it replaced with the vendor and now if i install ANY OS, at some point in installation it either freezes completely with no response for hours, or restarts automatically. I tried installing Windows 7, Windows Vista and Ubuntu 9.10. I tested the new RAM again and found no problems in about 2 passes using memtest86+. I even updated the BIOS using bootable USB and even the problem persists. I am really not sure which hardware is causing trouble. I dont have any OS inside it, so i have to check using bootable CDs DVDs and USB only. Please advice on how to proceed. Are there any suites/ separate tools for checking integrity of each hardware parts and troubleshoot it? I wanted to confirm which part is problematic before going for replacement. Thanks a lot! This is the config: Core i5, MSI P55-GD65, GSKill 2x2GB, Seagate 500GB 7200rpm, CM Extreme 600W PSU, Saphhire Radeon 5770 1GB, LG DVD Writer

  Read the article

• Automatically creating volume partitions on boot

  - by Justin Meltzer

  I followed this guide: http://www.mongodb.org/display/DOCS/Amazon+EC2+Quickstart to set up Mongodb. It had me create a RAID 10 array out of the four devices on EBS. Then it had me create a physical volume, a volume group, and three logical volumes out of that RAID 10 array. Lastly it had me create ext4 filesystems out of the logical volumes and mount them. Now the quickstart guide had me put two things in place so that these steps would be replicated on reboot of the system. It had me add some instructions to the mdadm.conf file to automatically create the RAID 10 array, and it also had me add instructions to the fstab file to automatically mount the filesystem for each logical volume. However, the quickstart guide does not have anything for automatically creating the logical volumes from the RAID 10 array. I checked my system and see that each of the four devices are part of a RAID array: $ sudo mdadm -Q /dev/sdh1 /dev/sdh1: is not an md array /dev/sdh1: device 0 in 4 device unknown raid10 array. Use mdadm --examine for more detail. However, the filesystem is never created or mounted from fstab because it's trying to mount it from logical volumes that were never created (or so it seems). My question is, how can I automatically accomplish all the steps from the quickstart guide on a reboot of the system, and what config file do I need to add data to so that I can automatically create these volume partions after the RAID 10 is created but before the filesystem is mounted. Also I'm unsure whether fstab actually creates and mounts the filesystem or just mounts the filesystem.

  Read the article

• Xamp on ubuntu serves php source for root url only

  - by mazaryk

  Hey, Okay, so installed xamp on my ubuntu machine, started it up and everything worked. Apache ran my php app just fine (including requests to the root url "/"). However, after the first reboot since installing, when I request "http://localhost/" apache serves up the index php page as a phtml source file. All other urls (like "http://localhost/login") work as expected. Backgound: The only modification I made to xamp was to setup a vhost for my app. The app uses an .htaccess file where I define some rewrite rules (the app is an MVC framework and all urls are rewritten to a single entry point php file). I'm using Xamp because I need php = 5.3.0. I know apache will serve up the source of a php file when it doesn't know to process php files. But the config does indeed have "AddType application/x-httpd-php .php" and as I said, the app works for all urls except the root "/" (and only since I've rebooted). The .htaccess file does contain a DirectoryIndex directive. xamp 1.3.7a Ubuntu 9.10 Any ideas?

  Read the article

• Scaling a node.js application, nginx as a base server, but varnish or redis for caching?

  - by AntelopeSalad

  I'm not close to being well versed in using nginx or varnish but this is my setup at the moment. I have a node.js server running which is serving either json, html templates, or socket.io events. Then I have nginx running in front of node which is serving all static content (css, js, etc.). At this point I would like to cache both static content and dynamic content to memory. It's to my understanding that varnish can cache static content quite well and it wouldn't require touching my application code. I also think it's capable of caching dynamic content too but there cannot be any cookie headers? I do use redis at the moment for holding session data and planned to use it for other things in the future like keeping track of non-crucial but fun stats. I just have no idea how I should handle caching everything on the site. I think it comes down to these options but there might be more: Throw varnish in front of nginx and let varnish cache static pages, no app code changes. Redis would cache dynamic db calls which would require modifying my app code. Ignore using varnish completely and let redis handle caching everything, then use one of the nginx-redis modules. I'm not sure if this would require a lot of app code changes (for the static files). I'm not having any luck finding benchmarks that compare nginx+varnish vs nginx+redis and I'm too inexperienced to bench it myself (high chances of my configs being awful). I'm basically looking for the solution that would be the most efficient in terms of req/sec and scalable in the future (throw new hardware at the problem + maybe adjust some values in a config = new servers up and running semi-painlessly).

  Read the article

• RewriteRule causes POST data to get dumped before I can access it

  - by MatthewMcGovern

  I'm currently setting up my own 'webserver' (a Ubuntu Server on some old hardware) so I can have a mess around with PHP and get some experience managing a server. I'm using my own little MVC framework and I've hit a snag... In order for all requests to make it through the dispatcher, I am using: <Directory /var/www/> RewriteEngine On RewriteCond %{REQUEST_URI} !\.(png|jpg|jpeg|bmp|gif|css|js)$ [NC] RewriteRule . HomeProjects/index.php [L] </Directory> Which works great. I read on Stackoverflow to change the [L] to [P] to preserve post data. However, this causes every page to return: Not Found The requested URL <url> was not found on this server. So after some more searching, I found, "Note that you need to enable the proxy module, and the proxy_http_module in the config files for this to work." The problem is, I have no idea how to do this and everything I google has people using examples with virtual hosts and I don't know how to 'translate' that into something useful for my setup. I'm accessing my webserver via my public IP and forwarding traffic on port 80 to the web server (like I'm pretending I have a domain/server). How can I get this enabled/get post data working again? Edit: When I use the following, the server never responds and the page loads indefinately? LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so <Directory /var/www/> RewriteEngine On RewriteCond %{HTTP_REFERER} !^http://(.+\.)?82\.6\.150\.51/ [NC] RewriteRule .*\.(jpe?g|gif|bmp|png|jpg)$ /no-hotlink.png [L] RewriteCond %{REQUEST_URI} !\.(png|jpg|jpeg|bmp|gif|css|js)$ [NC] RewriteRule . HomeProjects/index.php [P] </Directory>

  Read the article

• How do I install Apache Portable Runtime?

  - by apache

  My Apache is installed by yum install apache And now I'm trying to install subversion server from source following instructions here. But when I try to configure,get an error: [root@vps303 subversion-1.6.9]# ./configure configure: Configuring Subversion 1.6.9 configure: creating config.nice checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes ... checking for APR... no configure: WARNING: APR not found The Apache Portable Runtime (APR) library cannot be found. Please install APR on this system and supply the appropriate --with-apr option to 'configure' or get it with SVN and put it in a subdirectory of this source: svn co \ http://svn.apache.org/repos/asf/apr/apr/branches/1.2.x \ apr Run that right here in the top level of the Subversion tree. Afterwards, run apr/buildconf in that subdirectory and then run configure again here. Whichever of the above you do, you probably need to do something similar for apr-util, either providing both --with-apr and --with-apr-util to 'configure', or getting both from SVN with: svn co \ http://svn.apache.org/repos/asf/apr/apr-util/branches/1.2.x \ apr-util configure: error: no suitable apr found How do I get around this problem? BTW,will both client and server software be installed by compiling from source?

  Read the article

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

< Previous Page | 810 811 812 813 814 815 816 817 818 819 820 821  | Next Page >