Search Results

Search found 26810 results on 1073 pages for 'fixed point'.

Page 828/1073 | < Previous Page | 824 825 826 827 828 829 830 831 832 833 834 835  | Next Page >

  • Cannot get at data in my NAS

    - by Ben
    I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

    Read the article

  • Easiest way to do host name resolution with IPA?

    - by Luke
    We are currently using static LAN IP addresses for our internal non-public facing servers. We don't have DHCP configured. We're using Vyatta for our router and firewall. The firewall is configured to be zone based. We want to setup IPA for centralized authentication (LDAP+Kerberos). IPA is requiring resolvable host names. I want to avoid having to enter DNS records by hand. What is the most painless way to make host names resolvable that works with IPA in a Linux only environment? We arn't using anything to resolve host names now. Up until now we've been using static ip addresses and local users on each server. We've looked at BIND, DHCP (does that even solve the problem?), and multicast DNS. At this point we're not sure which solution would work best. Is there another option we haven't considered? Security is very important. We have multiple zones where each zone has very specific or no access to another zone. DNS for public domains is forwarded from Vyatta to our ISP's DNS server.

    Read the article

  • Limited bandwidth and transfer rates per user.

    - by Cx03
    I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

    Read the article

  • Would a PHP application benefit from being served from a RAM drive?

    - by Tom Marthenal
    I am in charge of hosting a PHP application that is large and slow, but easy to scale. The application is entirely static, with writable disk storage needed. We've profiled the application, and the main bottleneck appears to come from loading the application and not the work the application does. The application is not CPU-intensive, although it does use a fair amount of memory (think Magento). Currently we distribute it by having a series of servers with the same PHP files on their hard drive and a load balancer in front of them. Easy but expensive. I've been reading about RAM disks and the IO benefits they offer, and was wondering if they would be well-suited to PHP applications. Since PHP applications are loaded from disk for every request and often involve lots of different files (as opposed to being kept in memory like with a Java application), I would figure that disk performance can be a severe bottleneck. Would placing the PHP files on a RAM disk and using the mount point as Apache's document root offer performance benefits? A startup script could create the RAM drive and then copy the files (which are plain-text and small) from a permanent location to the temporary RAM drive. Does this make sense, or should I just trust the linux kernel to cache the appropriate files in memory by itself?

    Read the article

  • How can I rapidly switch hosts?

    - by EAMann
    I'm in the process of migrating a forum setup from one version of the software on one machine (older shared Windows host) to a new VPS (Windows Server 2008). To install the software, I used my hosts file to temporarily point the domain at the new IP address. To see the old site, I obviously re-edit the hosts file to remove the reference. But this leaves me constantly adding/removing a # from my hosts file just so I can switch back and forth between the two servers. Is there a way to do this more rapidly? I've found a handful of toggling batch scripts, but all they do is automate the addition/removal of the # character ... so there's still a noticeable lag where I have to repeatedly hit F5 to force my system to detect the new settings. Ideally, I could view both servers at the same time on the same machine. Maybe one through a regular browser session and one through some kind of a proxy. Unfortunately, I don't have the first idea how to set that up. Ideas?

    Read the article

  • Linux: Encryption of a physical LVM volume doesn't imply encryption of its logical subvolumes?

    - by java.is.for.desktop
    Hello, everyone! I installed OpenSuse one year ago on my notebook. I created all partitions except /boot inside an LVM partition. I enabled encryption for it during setup. The system asked me a password on each boot later. Everything seemed fine... But one day I wanted to cancel the boot process and did it with SysRq REISUB. During entering this combination, the system suddenly continued to boot without any password being entered. I had no /home and no swap, but / was mounted! I checked multiple times, it was inside an "encrypted" physical LVM volume. Later I found out that OpenSuse can't encrypt / at all. There is an option to enable encryption for each logical volume, and indeed it fails for /. Later I tried Fedora. The options during partitioning were misleading by same means. I could enable "encryption" of a physical volume and each logical subvolume. With the exception that Fedora actually allowed to encrypt /. Question: What's the point of setting up "encryption" for a physical LVM volume, when it doesn't imply (real) encryption of its logical subvolumes? Did I get something wrong in this whole concept?

    Read the article

  • "Document in ADF" on Canon MX340

    - by Michael Donohue
    I have a Canon MX340 multifunction printer. Recently, it keeps saying "Document in ADF" when I turn on the printer. I've tried clearing this multiple times, but as soon as the feeder wheels stop turning, in an attempt to clear the document feeder, it just pops up the same error again. This is particularly annoying, as it blocks all functions on the device - I cannot print, even though printing has no interaction with the document feeder. I've opened up the feeder device, as much as can be done with fingers alone. There just doesn't seem to be anything in there. I ran a sheet of paper through about six times, just to see if some dust might be getting in the way, and I've blown out the feeder with air. Still nothing. At this point, I don't care too much about the ADF working, I just want to disable whatever sensor is tripping this error message. Any ideas? I found this thread online, where a user has the same problem. But no resolution was reached there.

    Read the article

  • New to server admin, Diagnosing Memory and CPU issues on DV

    - by G Thompson
    Sorry for my ignorance and lack of knowledge. I'm a PHP/Front-end developer just now venturing into very minor server management/diagnostics. I have a Media Temple DV account. I have 2 sites that run a PHP script through a subscription service to an API. Basically API hits site with said script. Script runs, gathers data from api, saves data to SQL database. I noticed that these sites seemed to causing memory overages on my server (not sure why). So I temporarily disabled them. The memory overage alerts stopped but my CPU still sits really high, like at 115% and above. I'm trying to diagnos this with tutorials and resources but just can't seem to find a solution. I'll attach screenshots(screenshots are without the PHP scripts I assume are responsible for the memory issues) I'm assuming are important to the diagnosis, but if anyone can point me in the right direction to start A. figuring out if and why the PHP script may be causing memory overages and B. Why my CPU is always over 100%. Thanks guys! Links to screen shots... can't post with low points. http://i.stack.imgur.com/A64k4.png http://i.stack.imgur.com/qm1rV.png

    Read the article

  • A failed disk (Pay for professional service or SpinRite?)(new edit)

    - by huggie
    EDIT: After much negotiating and begging and seeing through promotion smoke screen, thanks to the nice representative who took my case, I now know that the engineer has already fixed my NTFS partition (I guess it might be a bad block in the partition table?). She told me that the problem was considered minor, and I should be able to boot normally and just copy stuff out. Whew..I'm glad I didn't agree to the NTD $16,000 deal. New question (should this be in a new thread?): is it safer to use the linux "dd" command or is it better to boot normally into Windows XP and just copy stuff out? EDIT2: Thanks to all the help. I give the best answer to Console as it's most directed related to my question. But many suggestion are helpful and informational. ---- ORIGINAL POST BELOW --- Hi, in my previous post (You don't need to read but it's at http://superuser.com/questions/48838/windows-xp-a-disk-read-error-occurred), I said that my hard disk was not booting and is showing "a disk read error occurred". I took it to a recovery professional. A representative responded today told me that the NTFS partitions have a "NTFS partition system crash". I have no idea what that means. The engineer handling my drive will not be available for contact till tomorrow. Now the company charges me NTD (New Taiwan Dollar) $16,000 to recover lost data, that's kind of a lot considering that my graduate student monthly stipend is currently NTD $32,000 (max. allowed by regulation, may be lower, may change depend on funding). Now I'm weighting in between the options. Option A: let the professional recovers it with the half of my monthly stipend. If file/directories I designated are not recovered I don't pay a penny. (other than the initial examination fee of NTD $1000 which I've already paid.) Option B: let me try SpinRite, if failed, back to Option A. I spoke to the representative at the company they recommended me not to handle it on my own (yeah of course that's what they all want to say, right?), and at the price tag the disk error is probably relatively minor and data recoverable. But the representative really did not have detailed information of the disk failure so I didn't take her recommendation readily. Though one thing I heed was that she said that what they would do is to duplicate the disk before attempting discovery, so there would be no data loss (Is this true? can't duplicating invoke further data loss?). That sounds very good to me. Or maybe a third option: Option C: Negotiate with them to pay them to duplicate the disk hopefully for a much smaller price tag. Let me try SpinRite, if failed, back to Option A. This is a difficult decision. Ultimately I want my data back, but if a cheaper way is available to achieve the same thing... Can operating with SpinRite also corrupt data in someway? I've no idea what happened to my drive. I'll attempt to contact the engineer and hope to get it clarified and make an edit here.

    Read the article

  • NFS on top of GFS2 - does it work?

    - by Matthew
    We're currently using a NoSQL derivative called Splunk to receive our data. The software supports something called "search head pooling" in which the job-dispatching engine is housed on several servers which share a common storage point. Originally our intention was to use a clustered filesystem like GFS2 because of low latency, stability, and ease of setup. We set up GFS2, and it's working with no issues. However when trying to run the software, it's trying to create lock files, and a bunch of other things that their support team can't quite explain. Ultimate feedback from them was that they only support NFS. Our network administration team heavily frowns on NFS (lack of stability, file lock issues, etc). So, I was thinking about the possibility of setting up NFS on each server in the cluster to act as a wedge layer between the GFS2 filesystem and the software. Basically configure each server to export the GFS2 filesystem's mountpoint via NFS, and then tell each server to connect to that NFS share. That way we aren't introducing any single-points-of-failure should a dedicated NFS server go down, but the vendor gets their "required" NFS share. I'm just brainstorming ways around, so please tear this apart :)

    Read the article

  • Frequency of RAM

    - by Vignesh Palani
    I have a very old system hp compaq dx2080. It had 1gb of RAM. I recently bought a EVM DDR2 1 GB PC RAM which had a clock rate of 667Mhz. I have dual booting windows 7 and 8. When I installed it, windows 7 was still using the older 1gb. It showed as 2 gb available and 1gb usable in system properties. I searched around and found that I can change it to max in the msconfig. I did so. I set it 2048. Still, it was using only 1gb. When, I switched to 8, it was using the 2gb. Now, for my question: My system only supported 553Mhz and 667Mhz RAM. In the BIOS, I saw that the new RAM was showing as 800Mhz. Rechecked using speccy and cpu-z. It showed different values between the two. The RAM is labeled as 667Mhz over it. No mistake in that. But, am I missing something? Please help. And, can I continue using it? My point again. There are only two slots.

    Read the article

  • Reverse SSH tunnel: how can I send my port number to the server?

    - by Tom
    I have two machines, Client and Server. Client (who is behind a corporate firewall) opens a reverse SSH tunnel to Server, which has a publicly-accessible IP address, using this command: ssh -nNT -R0:localhost:2222 [email protected] In OpenSSH 5.3+, the 0 occurring just after the -R means "pick an available port" rather than explicitly calling for one. The reason I'm doing this is because I don't want to pick a port that's already in use. In truth, there are actually many Clients out there that need to set up similar tunnels. The problem at this point is that the server does not know which Client is which. If we want to connect back to one of these Clients (via localhost) then how do we know which port refers to which client? I'm aware that ssh reports the port number to the command line when used in the above manner. However, I'd also like to use autossh to keep the sessions alive. autossh runs its child process via fork/exec, presumably, so that the output of the actual ssh command is lost in the ether. Furthermore, I can't think of any other way to get the remote port from Client. Thus, I'm wondering if there is a way to determine this port on Server. One idea I have is to somehow use /etc/sshrc, which is supposedly a script that runs for every connection. However, I don't know how one would get the pertinent information here (perhaps the PID of the particular sshd process handling that connection?) I'd love some pointers. Thanks!

    Read the article

  • System With Two Network Adapters [closed]

    - by Synetech inc.
    Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

    Read the article

  • Ubuntu 11.04 fresh install - "Input signal out of range" or "Mode not supported..."

    - by Dennis
    I recently installed Ubuntu 11.04 using a CD .iso. Installation went fine. Upon completion I rebooted and after a second or two I got a black screen with the message "Input signal out of range". And there it sits... Read a few things about how this could be related to screen resolution, refresh rate, etc. For the heck of it I tried a different monitor. The result is the same but the message provides some clues - "Mode not supported - H:92.7kHz, V:58.3Hz" (the latter is Hz; not kHz). So my thought is that I should probably be able to use the 11.04 install disc to "Try out Ubuntu", find and edit some file that was created by the install with the correct values. Problem is, I am not too sure what I am supposed to edit. Looked at the xorg.conf file but this is so minimal at this point I am not sure it is where I want to go. By the way, the monitor is an I-Inc ix191a. Anyone have any ideas on how to get around this?

    Read the article

  • Hard drive write speed - finding a lighter antivirus?

    - by Shingetsu
    I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

    Read the article

  • Logging Remote Desktop to Servers via Logon Script or GPO or What?

    - by Nate Bross
    The objective here is to start a simple .NET application I've written which captures some environment variables (time, username, computername, etc) upon login. This .NET application subscribes to the Windows "User logout" event. Upon launch, the application captures the above variables, and creates a record in my database, upon logout (which I'm capturing) I update another field in the same record, with the logout time. The above is working exactly as I would like, when I launch the binary, it makes its initial log entry, then waits for the logout event and updates the same record. Restrictions, the .NET binary should be able to live on a share point (\server\share\myapp\v1) so I can update the application to (\server\share\myapp\v2) and simply update the GPO/Logon script. My initial thought was to use the \domaincontroller\sysvol\ directory to store the binary and then update all user accounts to include a call to my application. Can you see any flaws in this approach? My question is this: First, is there anything wrong with my idea above? Second, if so, what is the best way (through group policy or otherwise) to ensure this application launches whenever a session is started on a server?

    Read the article

  • Linux iptables / conntrack performance issue

    - by tim
    I have a test-setup in the lab with 4 machines: 2 old P4 machines (t1, t2) 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t3) Intel e1000 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t4) Intel e1000 to test linux firewall performance since we got bitten by a number of syn-flood attacks in the last months. All machines run Ubuntu 12.04 64bit. t1, t2, t3 are interconnected through an 1GB/s switch, t4 is connected to t3 via an extra interface. So t3 simulates the firewall, t4 is the target, t1,t2 play the attackers generating a packetstorm thorugh (192.168.4.199 is t4): hping3 -I eth1 --rand-source --syn --flood 192.168.4.199 -p 80 t4 drops all incoming packets to avoid confusion with gateways, performance issues of t4 etc. I watch the packet stats in iptraf. I have configured the firewall (t3) as follows: stock 3.2.0-31-generic #50-Ubuntu SMP kernel rhash_entries=33554432 as kernel parameter sysctl as follows: net.ipv4.ip_forward = 1 net.ipv4.route.gc_elasticity = 2 net.ipv4.route.gc_timeout = 1 net.ipv4.route.gc_interval = 5 net.ipv4.route.gc_min_interval_ms = 500 net.ipv4.route.gc_thresh = 2000000 net.ipv4.route.max_size = 20000000 (I have tweaked a lot to keep t3 running when t1+t2 are sending as many packets as possible). The result of this efforts are somewhat odd: t1+t2 manage to send each about 200k packets/s. t4 in the best case sees aroung 200k in total so half of the packets are lost. t3 is nearly unusable on console though packets are flowing through it (high numbers of soft-irqs) the route cache garbage collector is no way near to being predictable and in the default setting overwhelmed by very few packets/s (<50k packets/s) activating stateful iptables rules makes the packet rate arriving on t4 drop to around 100k packets/s, efectively losing more than 75% of the packets And this - here is my main concern - with two old P4 machines sending as many packets as they can - which means nearly everyone on the net should be capable of this. So here goes my question: Did I overlook some importand point in the config or in my test setup? Are there any alternatives for building firewall system especially on smp systems?

    Read the article

  • Batch-Remove Specific Text from Photo Descriptions

    - by David
    I've recently upgraded to iPhoto '11 (couldn't resist the pricing on the new app store) and as I'm adding more meta-data to my library and generally organizing things (places, faces, etc... I hadn't upgraded since '08) I've noticed something odd in my photos. Every photo in my library has a description (though many are short), but it would appear that somehow the description of one of the photos has been appended to many. I don't know if maybe I accidentally screwed up a batch change at some point in the past, or if the library upgrade somehow messed up, or what else may have happened. But what I need to do is fix these somehow. Now, manually editing is something of a daunting task. Within a library of 21,248 photos, 18,858 of them have this additional text. The one thing I do have going for me is that it's a specific string. If there's a way to "remove this string from everywhere in the library without removing the rest of any given description" then that would be perfect. Is there anything I can do like this? Maybe even manually editing a library file in a text editor? (Would that break anything else in iPhoto if its library was edited outside of the application, even while it's not running?) Does anybody have any ideas?

    Read the article

  • iptables logging not working?

    - by vps_newcomer
    OS: Ubuntu 10.04 Logging daemon: rsyslog For some reason i'm not getting any iptables logs, even thought i don't look through them very often i'd still like to get it working for the sake of it working XD Here is my /etc/ryslog.d/iptables.conf :msg, contains, "[IPTABLES]" -/var/log/iptables.log & ~ My iptables logging prefix is "[IPTABLES]" followed by whatever else (example [IPTABLES] Denied xyz) the /var/log/iptables.log file is being created, however its not getting any entries. I can see the logging entries in dmesg but not in syslog or messages. Whats going on? EDIT: My iptables logging rules: # logging limit LoggingLimit=5/min LoggingPrefix=IPTABLES # Logging chain iptables -N LOG_REJECT iptables -A LOG_REJECT -j LOG # join INPUT to LOG_REJECT iptables -A INPUT -j LOG_REJECT # logging iptables -A LOG_REJECT -p tcp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied TCP: " #--log-level 7 iptables -A LOG_REJECT -p udp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied UDP: " #--log-level 7 iptables -A LOG_REJECT -p icmp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied ICMP: " #--log-level 7 Update: I found a thread that has the same symptoms as i do, apparently is a kernel bug. I am using a VPS so could anyone point me on how to upgrade my kernel or apply a workaround? I couldn't find a 2.6.34 kernel listed in apt-cache. Thread: http://www.linode.com/forums/viewtopic.php?t=5533

    Read the article

  • crontab not running on VirtualBox unless I'm logged in

    - by Mike
    I am running Ubuntu Server 9.04 in VirtualBox on my work PC as a development environment. I have some scripts that I've put in my user's crontab that run throughout the day while I'm SSHed into the VM. Last night, I closed PuTTy and all of my other running applications (except for VirtualBox and the VM) and went home. I came back this morning to discover that my cron jobs didn't run at all, yet when I SSHed into the VM, the next scheduled job ran. I set the schedule to 5min to test, disconnected again, and the jobs stopped running on schedule. They seem to only run if I'm logged in to the machine. Obviously, I want them to run on schedule even if I'm not logged in to the VM, otherwise there's no point. Is there something I've failed to configure correctly? New Information: There are now 3 entries in /var/log/cron.log saying the following "Mount of private directory return code [256]"... the entries correspond to when the cron job is supposed to run. I thought they are supposed to run as my userid? Why would my own userid be unable to run a script in my home directory?

    Read the article

  • Scripting around the lack of user:password@domain url functionality in jscript/IE

    - by Idiomatic
    I currently have a jscript that runs a php script on a server for me, dead simple. But... I want to be atleast somewhat secure so I setup a login. Now if I use the regular user:password@domain system it won't work (IE decided it was a security issue). And if I let IE just remember the password then it pops up a security message confirming my login every time (which kills the point of the button). So I need a way to make the security message go away. I could lower security settings, which tbh I am fine with but nothing seems to make it fuck off (there might be some registry setting to change). Find a fix for jscript that will let me use a password in the url. There used to be a regedit that worked for older systems which allowed IE to use url passwords (not working on my 64bit windows7 setup) though I doubt that'd have helped jscript anyways (since it outright crashes). Use an app other than IE. Inwhich case I'm not sure how to go about it, I want it to be responsive and invisible so IE was a good choice. It is near instant. Use XMLHttpRequest instead of IE directly? May even be faster but I've no idea if it'd help or just have the same error. Use a completely different approach. Maybe some app that can script website browsing. var args = {}; var objIEA = new ActiveXObject("InternetExplorer.Application"); if( WScript.Arguments.Item(0) == "pause" ){ objIEA.navigate("http://domain/index.html?pause"); } if( WScript.Arguments.Item(0) == "next" ){ objIEA.navigate("http://domain/index.html?next"); } objIEA.visible = false; while(objIEA.readyState != 4) {} objIEA.quit();

    Read the article

  • OpenVZ container is running but does not show in vzlist nor can I find the private/conf files for the container

    - by Kakeakeai
    I was creating a new OpenVZ container on one of our VPS Nodes while the power went out for that machine. After bringing the machine back online I could no longer access the container CTID=101. I could not destroy it using "vzctl destroy 101", I can not enter or control it, and "vzlist -a" does NOT display any containers at all (this was a fresh node and the first container was being created). I decided to create a new container at this point assuming that the old container just was not saved for some reason. However when I go to add the ip/host to the new container I get a warning that the IP is already in use. After doing a ping to the IP I realized there was a machine on that IP. I SSH into the machine and discover it is the OLD container that some how is orphaned. I can not find it on the filesystem, I can not find it using VZ commands, and It is set to start on Node boot so it is impossible to shutdown (even ssh in and typing the "shutdown now" command just reboots the container not shut it down). Is this a flaw in OpenVZ or am I missing something? I have all the outputs and logs if needed. Thank you all so much in advance.

    Read the article

  • Adventures in Drupal multisite config with mod_rewrite and clean urls

    - by moexu
    The university where I work is planning to offer Drupal hosting to staff/faculty who want a Drupal site. We've set up Drupal multisite with clean urls and it's mostly working except for some weird redirects. If you have two sites where one is a substring of the other then you'll randomly be redirected to the other site. I tracked the problem to how mod_rewrite does path matching, so with a config file like this: RewriteCond %{REQUEST_URI} ^/drupal RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ /drupal/index.php?q=$1 [last,qsappend] RewriteCond %{REQUEST_URI} ^/drupaltest RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ /drupaltest/index.php?q=$1 [last,qsappend] /drupaltest will match the /drupal line and all of the links on the /drupaltest page will be rewritten to point to /drupal. If you put the end of string character ($) at the end of each rewrite condition then it will always match on the correct site and the links will always be rewritten correctly. That breaks down as soon as a user logs in though because the query string is appended to the url so just the base url will no longer match. You can also fix the problem by ordering the sites in the config file so that the smallest substring will always be last. I suggested storing all of the sites in a table and then querying, sorting, and rewriting the config file every time a Drupal site is requested so that we could guarantee the order. The system administrator thought that was kludgy and didn't address the root problem. Disabling clean urls should also fix the problem but the users really want them so I'd prefer to keep them if possible. I think we could also fix it by using an .htaccess file in each site to handle the clean url rewriting but that also seems suboptimal since it will generate a higher load on the server and the server is intended to host the majority of the university's external facing web content. Is there some magic I can do with mod_rewrite to get it to work? Would another solution be better? Am I doing something the wrong way to begin with?

    Read the article

  • Setting up a global MySQL Cluster in the cloud

    - by GregB
    I'm giving the question an overhaul to more specifically identify where I need help. I use two tools to manage a bunch of cloud server: Puppet and Rundeck. Both of these can be configured to use a mysql backend. I'd like to setup an instance of each application in both the U.S., and the U.K., treating the U.K. servers as hot stand-bys in case of failure in the U.S. I want to use a MySql cluster so that the data is automatically replicated from the U.S. to the U.K. Because these are hot standbys, high performance is not a goal. Redundancy and data integrity are most important. My question revolves around the setup of the mysql cluster. I want to run three servers, each one running a data node, a sql node, and a management node. Is this a valid configuration for mysql server? If so, could someone point me in the right direction for creating such a setup? I've downloaded the offical tarball, and the official debian, and the documentation for them contradicts many of the online tutorials. I'm installing on Ubuntu 10.04.

    Read the article

  • How to make Windows command prompt treat single quote as though it is a double quote?

    - by mark
    My scenario is simple - I am copying script samples from the Mercurial online book (at http://hGBook.red-bean.com) and pasting them in a Windows command prompt. The problem is that the samples in the book use single quoted strings. When a single quoted string is passed on the Windows command prompt, the latter does not recognize that everything between the single quotes belongs to one string. For example, the following command: hg commit -m 'Initial commit' cannot be pasted as is in a command prompt, because the latter treats 'Initial commit' as two strings - 'Initial and commit'. I have to edit the command after paste and it is annoying. Is it possible to instruct the Windows command prompt to treat single quotes similarly to the double one? EDIT Following the reply by JdeBP I have done a little research. Here is the summary: Mercurial entry point looks like so (it is a python program): def run(): "run the command in sys.argv" sys.exit(dispatch(request(sys.argv[1:]))) So, I have created a tiny python program to mimic the command line processing used by mercurial: import sys print sys.argv[1:] Here is the Unix console log: [hg@Quake ~]$ python 1.py "1 2 3" ['1 2 3'] [hg@Quake ~]$ python 1.py '1 2 3' ['1 2 3'] [hg@Quake ~]$ python 1.py 1 2 3 ['1', '2', '3'] [hg@Quake ~]$ And here is the respective Windows console log: C:\Workpython 1.py "1 2 3" ['1 2 3'] C:\Workpython 1.py '1 2 3' ["'1", '2', "3'"] C:\Workpython 1.py 1 2 3 ['1', '2', '3'] C:\Work One can clearly see that Windows does not treat single quotes as double quotes. And this is the essence of my question.

    Read the article

< Previous Page | 824 825 826 827 828 829 830 831 832 833 834 835  | Next Page >