Search Results

Search found 27606 results on 1105 pages for 'javascript disabled'.

Page 840/1105 | < Previous Page | 836 837 838 839 840 841 842 843 844 845 846 847  | Next Page >

• Copying photos from camera stalls - how to track down issue?

  - by Hamish Downer

  When I copy files from my camera (connected via USB) to the SSD in my laptop a few files get copied and then the copy stalls. I'm not sure why, any ideas or things to investigate appreciated, or bug reports to go and look at. I have read this answer - the camera (Canon 40D in case that matters) mounts fine using gvfs. I can see the photos in Nautilus, or in the terminal (in /run/user/username/gvfs/... ) and I can copy a few photos, but not many. Using the terminal or Nautilus the process hangs until the camera goes to sleep. Digikam fails to copy any at all, as does Rapid Photo Downloader. Shotwell did manage it in the end, but that is very much a work around for me. I have disabled thumbnail generation by nautilus. Load average stays about 1 while this is happening, while CPU usage is half idle, half wait (and a little user/sys for other programs). None of the programs at the top of the cpu list in top are related to copying photos. There is not much in the logs - from /var/log/syslog Dec 2 16:20:52 mishtop dbus[945]: [system] Activating service name='org.freedesktop.UDisks' (using servicehelper) Dec 2 16:20:52 mishtop dbus[945]: [system] Successfully activated service 'org.freedesktop.UDisks' Dec 2 16:21:24 mishtop kernel: [ 2297.180130] usb 2-2: new high-speed USB device number 4 using ehci_hcd Dec 2 16:21:24 mishtop kernel: [ 2297.314272] usb 2-2: New USB device found, idVendor=04a9, idProduct=3146 Dec 2 16:21:24 mishtop kernel: [ 2297.314278] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Dec 2 16:21:24 mishtop kernel: [ 2297.314283] usb 2-2: Product: Canon Digital Camera Dec 2 16:21:24 mishtop kernel: [ 2297.314287] usb 2-2: Manufacturer: Canon Inc. Dec 2 16:21:24 mishtop mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Dec 2 16:21:24 mishtop mtp-probe: bus: 2, device: 4 was not an MTP device This problem has only started recently and I've had all the hardware for ages. I have also recently upgraded to 12.10, though I'm not sure if the problem started when I upgraded or after the upgrade. I also note this similar question but it is currently unanswered and I'm providing more detail

  Read the article

• How do I choose which way to enable/disable, start/stop, or check the status of a service?

  - by Glyph

  If I want to start a system installed service, I can do: # /etc/init.d/some-svc start # initctl start some-svc # service some-svc start # start some-svc If I want to disable a service from running at boot, I can do: # rm /etc/rc2.d/S99some-svc # update-rc.d some-svc disable # mv /etc/init/some-svc.conf /etc/init/some-svc.conf.disabled Then there are similarly various things I can do to enable services for starting at boot, and so on. I'm aware of the fact that upstart is a (relatively) new thing, and I know about how SysV init used to work, and I'm vaguely aware of a bunch of D-Bus nonsense, but what I don't know is how one is actually intended to interface with this stuff. For example, I don't know how to easily determine whether a service is an Upstart job or a legacy SysV thing, without actually reading through the source of its shell scripts extensively. So: if I want to start or stop a service, either at the moment or persistently, which of these tools should I use, and why? If the answer depends on some attribute (like "this service supports upstart") then how do I quickly and easily learn about that attribute of an installed package? Relatedly, are there any user interface tools which can safely and correctly interact with the modern service infrastructure (upstart, and/or whatever its sysv compatibility is)? For example, could I reliably use sysv-rc-conf to determine which services should start?

  Read the article

• PHP safe_mode is a pain, looking for advice (Ubuntu 12.04 server, public webserver)

  - by user73279

  Maybe askUbuntu isn't the right forum or I haven't provided the right search query but I haven't seen anything in my searching of askUbuntu on PHP safe_mode. I get lots of Windows Safe Mode and Ubuntu Safe Mode results but not PHP safe_mode. So I keep running into one issue after another regarding PHP safe_mode. (I write a lot of my own PHP code for various site maintenance tools and such.) I know safe_mode is going away in the next version of PHP but I still see a fair amount of advice recommending that you leave it enabled. I've recently consolidated from 3 servers down to 1 and at least one of those old servers had safe_mode disabled without any issues. (The lack of issues may have simply been a matter of good luck.) None of the previous 3 gave me this much trouble so I'm guessing so additional php.ini/PHP safe_mode setting was turned on for the new server. I primarily run WordPress for my websites with a few MediaWiki sites sprinkled in. And I am currently running into an issue using WordPress's auto update feature as it doesn't seem to be able to use fopen. WordPress is not relaying the actual error message to me but since I was just able to update the plugins I'm using this is a safe_mode problem. I've had a lot of safe_mode issues since consolidating to this new server. Long story short, the advice I'd seen to use safe_mode was all at least 2 years old. Do I really need it? If I disable PHP safe_mode are there a good set of security measures I should implement - i.e. chmod 640 /var/www/..., add this to your .htaccess, etc - to protect my server/sites? Thanks

  Read the article

• Eclipse Java Code Formatter in NetBeans Plugin Manager

  - by Geertjan

  Great news for Eclipse refugees everywhere. Benno Markiewicz forked the Eclipse formatter plugin that I blogged about sometime ago (here and here)... and he fixed many bugs, while also adding new features. It's a handy plugin when you're (a) switching from Eclipse to NetBeans and want to continue using your old formatting rules and (b) working in a polyglot IDE team, i.e., now the formatting rules defined in Eclipse can be imported into NetBeans IDE and everyone will happily be able to conform to the same set of formatting standards. And now you can get it directly from Tools | Plugins in NetBeans IDE 7.4: News from Benno on the plugin, received from him today: The plugin is verified by the NetBeans community and available in the Plugin Manager in NetBeans IDE 7.4 (as shown above) and also at the NetBeans Plugin Portal here, where you can also read quite some info about the plugin:  http://plugins.netbeans.org/plugin/50877/eclipse-code-formatter-for-java The issue with empty undo buffer was solved with the help of junichi11: https://github.com/markiewb/eclipsecodeformatter_for_netbeans/issues/18 The issue with the lost breakpoints remains unsolved and there was no further feedback. That is the main reason why the save action isn't activated by default. See also the open known issues at https://github.com/markiewb/eclipsecodeformatter_for_netbeans/issues?state=open Features are as follows:  Global configuration and project specific configuration.  On save action, which is disabled by default. Show the used formatter as a notification, which is enabled by default.  Finally, Benno testifies to the usefulness, stability, and reliability of the plugin: I use the Eclipse formatter provided by this plugin every day at work. Before I commit, I format the sources. It works and that's it. I am pleased with it. Here's where the Eclipse formatter is defined globally in Tools | Options: And here is per-project configuration, i.e., use the Project Properties dialog of any project to override the global settings:  Interested to hear from anyone who tries the plugin and has any feedback of any kind! 

  Read the article

• Fun Upgrading to .Net 4.0

  - by Sam Abraham

  We are currently in the process of upgrading one of our applications to .Net 4.0. Aside from us geeks wanting to always use latest and greatest technologies, an immediate business need for Silverlight 4.0 features justified our upgrade endeavor. The following is a summary of some issues we ran into with our web project:   For security purposes, the IIS 7 .Net 4.0 ISAPI filter is disabled. “Allow” it from the ISAPI and CGI Restrictions screen as shown:   Figure 1 - Allowing ASP.Net 4.0 ISAPI Filter   By default the Web Setup Project only requires the .Net Framework 4 Client Profile to be installed on target system, which offers a lighter weight install for client machines consuming .Net 4.0 applications. However, using certain .Net 4.0 features requires the full .Net 4.0 Framework as outlined in this link: http://msdn.microsoft.com/en-us/library/cc656912.aspx. We hence needed to update the installer to require the complete .Net 4.0 Framework on the target machine and to prompt for its installation if needed.   To accomplish this goal, we updated the installer’s launch conditions to check for .Net 4.0 as well as the installer prerequisites as shown:     Figure 2- Ensure Web Setup Project runs on full .Net 4.0 version Figure 3 - Launch Conditions screen Figure 4 - Set launch condition to .Net 4.0. Figure 5 -Changing installer prerequisites Figure 6 -Changing installer prerequisites

  Read the article

• Switching to workspaces view shows buggy blue background

  - by G1i1ch

  When switching to workspaces view everything the background turns blue. Same happens when I switch between multiple windows of the same app too. Happening after having a try with gnome shell out of curiosity. Installed through official repos like normal. Tried it out but switched back, anyone have an idea of why this is happening? Got an Intel GPU and Unity 3d. If anyone can give me some direction, thanks a lot. Update: Looks like during the switch somehow opengl was disabled. glxinfo returns: name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". This is very distressing, all I wanted to do was try out gnome3. Does anyone have an idea on how I can get opengl back? [update] Ok I found out what happened. Apparently it's not that hard to accidentally install an nvidia driver. All I had to do was remove all the stuff that had nvidia in it and I got 3d back! For anyone else, this is how I found out: check out Xorg.0.log `$ cat / var/log/Xorg.0.log | more` if you see a line like this somewhere `(EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)` you got an nvidia problem Thanks everyone for trying to help :D

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Impossible to enable bluetooth under Ubuntu

  - by PCh

  I just installed Ubuntu 12.04 (dual boot, kept Windows just in case) on my new Acer Aspire One 756-877. As soon as I installed it I also installed the Broadcom driver, since wifi wasn't working, and that solved it right away. But when I tried Bluetooth, I had a problem that I see is quite recurring: -The hardware is on (and working fine under Windows) -The icon shows up on the menu, giving me the options of turning Bluetooth on or off, and then just "Bluetooth preferences". -I can apparently turn it on that way, which only lights up the icon but makes no difference at all (and doesn't give any other options in the Bluetooth menu) -When I open "Bluetooth preferences" (whether Bluetooth is apparently on or off, it makes no difference), it says it's disabled and will not let me slide the button to enable it. I've rebooted, but nothing happens. -The material is Broadcom and the port (if it's relevant at all) is Port_#0001.Hub_#0003 I tried the following commands suggested in other similar questions, with no result at all: sudo dmesg | grep blue and sudo service bluetooth start and sudo /etc/init.d/bluetooth start Any other clues on what I can do? Thanks for your time!

  Read the article

• Windows 8 BIOS - Boot Ubuntu from External HDD

  - by F3AR3DLEGEND

  My laptop came pre-loaded with Windows 8 64-bit (only storage device is a 128 GB SSD). Since it is my school laptop/I've heard creating a Linux partition alongside Windows 8 is not very wise I installed Ubuntu onto my external hard drive. I have a 500GB external HDD with the following partitions: Main Partition - NFTS - ~400 GB Extension Partition / - ext2 - ~25gb /home - ext2 - ~30gb swap - ext2 - 10gb /boot - ? - 10gb ? = not sure of partition Using the PenDriveLinux installer, I created a LiveUSB version of Ubuntu 12.04 (LTS) on a 4GB USB drive. Using that, I installed Ubuntu onto the external hard-drive, without any errors (or at least none that I was notified of). Using the BIOS settings, I changed the OS-loading order so that it is in this order: My External USB HDD Windows Boot Loader Some other things Therefore, Ubuntu should load from my hard drive first, but it doesn't. Also, my hard drive is in working condition, and it turns on when BIOS starts (there is a light indicator). When I start my laptop, it goes directly to Windows 8 (I have the fast startup setting disabled as well). So, is there any way for me to set it up so that when my HDD is connected, it will automatically load Ubuntu? Thanks in advance!

  Read the article

• Ubuntu 13.10 No Sound

  - by spiersie

  I was running 13.04 since last monday and just today i upgraded to 13.10, in both of these version i have not managed to get my sound working. I have gone into alsamixer and disabled auto mute and the volumes are up. However if somebody thinks they can help me fix this i will gladly follow any steps. Please lay specifically any terminal commands you need me to do to either show specs or solve the problem as i am not fluent with the linux commands, this desktop being my first system to run linux, starting last monday. blake@Blake-Ubuntu-PC:~$ lspci -v | grep -A7 -i "audio" 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Trinity HDMI Audio Controller Subsystem: ASUSTeK Computer Inc. Device 8526 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at fef44000 (32-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:10.0 USB controller: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller (rev 03) (prog-if 30 [XHCI]) 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller (rev 01) Subsystem: ASUSTeK Computer Inc. Device 8445 Flags: bus master, slow devsel, latency 32, IRQ 16 Memory at fef40000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge (rev 11)

  Read the article

• [Oracle Identity Manager] 11g R2 Bundle Patch 09 is Available!

  - by mustafakaya

  Oracle Identity Manager Bundle Patch 09 is available now. You can download BP09 from here. Also,there is a important recommendation for BP08!  List of bugs fixed with BP09; Bug:12699224 : Trusted source reconciliation fails to create users with many reconciliation field mappings. Bug:14407437 : Provisioning through bulk request inserts null records into child tables. Bug:14493217 : Target resource reconciliation throws ORA-06512 error when the Descriptive field is mapped to a field that does not have a reconciliation field mapping. Bug:16044671 : User form customization fails if a UDF contains invalid character. Bug:16545968 : Modifying any attribute on a service account changes the account type as a primary account. Bug:16562633 : Oracle Identity Manager throws javax.el.elexceptions while viewing profile under direct report. Bug:16662834 : User not reprovisoned after user is deleted and created in the target with the same orclguid. Bug:16662905 : If an LOV field is required on an Application Instance form, no validation is enforced on the LOV field although it is required. Bug:16701873 : The Members tab of a role displays only enabled users and does not display disabled users. Bug:16862846 : When a notification is being sent, the mail ID in the Reply To field is set as the recipient's mail ID instead of the sender's mail ID. Bug:16824062 : When you use API to fetch or delete child data from an account, the child data row value is null. Therefore, child data is not returned. Bug:16912736 : There is a performance issue when the provisioned application instance details is opened for a user.

  Read the article

• Maximum 5 minute battery life with Ubuntu 11.10 on HP laptop

  - by JamesG

  I apologise if this question is too similar to the numerous others already asked, but it seems that my difference in battery life is significantly more noticeable than others that have been reported. I recently installed Ubuntu 11.10 on my HP Pavilion dv6 laptop (which I purchased brand new just under one year ago). When running Windows 7 on this laptop, I have been able to get up to two and a half to three hours of battery life with wireless disabled and when running only Microsoft Word. However, when running Ubuntu, I am unable to use the laptop if it is not plugged in. Upon unplugging the fully-charged machine from the power cord, if I have wireless enabled, I immediately receive a notification that the battery levels are critically low and that shutdown is imminent. Even if I replace the power plug, the laptop shuts down within thirty seconds. If I disable wireless capability, I am able to run the laptop for an absolute maximum of five minutes on battery powers before receiving the same message. I have tried running with Jupiter on Power Saver mode, but to no noticeable effect. Ignoring the fact that I can't use my laptop without being attached to a power source, I really do enjoy using Ubuntu, and hence would greatly appreciate any help that can be offered.

  Read the article

• How do I stop sound coming from my speakers with a faulty headphone socket?

  - by Andy

  On my laptop, I have a faulty headphone socket, so when I insert headphones into it, the speakers do not mute. I can confirm that this problem is caused by faulty hardware and not software as when I twist the headphone jack, the speakers come on and off according to the movements. On previous versions of Ubuntu, I worked around this problem by going into alsamixer and disabling "Auto-Mute Mode", and then going into the sound settings and choosing "Analog Headphones". However, on 12.04, no such option exists, rendering my headphones unusable with no way to work around the problem. I momentarily thought I had this problem fixed when I installed PulseAudio Volume Control from the Software Centre. I selected the Output Devices tab, and under "Built-in Audio Analogue Stereo" I selected "Headphones" for the port. However, this almost randomly seems to change back to "Speakers", despite me setting "Auto-Mute Mode" as disabled. Basically, I would like a way to permanently mute the speakers so only the headphones will play sound, without it losing my settings. It is ridiculous that such a simple setting has been taken away to "simplify" the user interface.

  Read the article

• Oracle SOA Suite for healthcare integration Dashboard

  - by Nitesh Jain

  Oracle SOA Suite Healthcare came up with a new way of monitoring where user can configure a dashboard and follow the dynamic runtime changes.Oracle SOA Suite for healthcare integration dashboards display information about the current health of the endpoints in a healthcare integration application. You can create and configure multiple dashboards as needed to monitor the status and volume metrics for the endpoints you have defined. The Dashboards reflects changes that occur in the runtime repository, such as purging runtime instance data, new messages processed, and new error messages. You can display data for various time periods, and you can manually refresh the data in real time or set the dashboard to automatically refresh at set intervals.Dashboard shows the following information: Status: The current status of the endpoint, such as Running, Idle, Disabled, or Errors. Messages Sent: The number of messages sent by the endpoint in the specified time period. Messages Received: The number of messages received by the endpoint in the specified time period. Errors: The number of messages with errors for the endpoint in the given time period. Last Sent: The date and time the last message was sent from the endpoint. Last Received: The date and time the last message was received from the endpoint. Last Error: The date and time of the last error for the endpoint.  It also shows the detailed view of a specific Endpoint The document type. The number of messages received per second. The total number of message processed in the specified time period. The average size of each message.

  Read the article

• Still can't mount windows 8 drive after restart

  - by Ishai Bloch

  After following the instructions in other posts, I am still getting the same error when I try to mount my Windows 8 drive in Ubuntu 14.04 on a dual boot system. I have disabled fast start after shutdown, hybrid hibernation, and the preinstalled Asus Instant On service. I have tried restarting Windows rather than shutting down. In all cases I get the same error message, namely: Error mounting /dev/sda4 at /media/jesse/OS: Command-line `mount -t "ntfs" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid=1000,dmask=0077,fmask=0177" "/dev/sda4" "/media/jesse/OS"' exited with non-zero exit status 14: Windows is hibernated, refused to mount. Failed to mount '/dev/sda4': Operation not permitted The NTFS partition is in an unsafe state. Please resume and shutdown Windows fully (no hibernation or fast restarting), or mount the volume read-only with the 'ro' mount option. I did not have the same issue before upgrading from Ubuntu 12 to 14. For what it's worth my computer is supposedly a "hybrid" with an SSD drive installed, although I can't see that the SSD drive is being used at all with my present settings. Any thoughts?

  Read the article

• Intel 5100 AGN disconnects and then disables my Verizon FiOS Actiontec router

  - by Anthony

  I am a new user (my first trial) of Ubuntu and booted up my Windows Vista laptop up with the Ubuntu CD. I was able to connect wirelessly to my router and stay connected for about a minute. After that it would disconnect and my router would be disabled: none of my other wireless devices would see the signal any longer, as if it disappeared. I would have to cycle the router's power toggle off/on to get it to come back on and put out a signal again. This happened repeatedly. I experienced no other problems trying the software (i.e., accessed my files w/o issue). I did not attempt to connect with an Ethernet cable. Here are the specs on my system: laptop is HP Pavilion dv5 Notebook PC system type is 64-bit operating system CPU is Intel Core 2 Duo P8600 2.4GHz ram is 4 GB network card is Intel WiFi Link 5100 AGN I read elsewhere in this forum that 64-bit systems may not be compatible with Ubuntu. Can anyone help me with this? I'd really like to be able to use this op system.

  Read the article

• Simple dependency tree diagram generator

  - by foampile

  I have a need to produce a simple dependency tree diagram. The input data would be in the following simple format: ITEM_NAME DEPENDENCY ---------------------------- ITEM_101 ITEM_75 ITEM_102 ITEM_77 ITEM_102 ITEM_61 ITEM_102 ITEM_11 This means that ITEM_101 depends on ITEM_75 and ITEM_102 depends on items ITEM_77, ITEM_61 and ITEM_11. So the diagram would have items ITEM_77, ITEM_61 and ITEM_11 in one vertical level and ITEM_102 would be below it with a line connecting each of the three dependencies to ITEM_102. The same would be for ITEM_101, ITEM_75 would be somewhere above it and there would be a line connecting it. In the real world this tree represents a hierarchy of scheduling jobs. We have a very extensive workload automation hierarchy in Autosys and I have heard that its front end utility has something like this tree visual representation, however, for some reason, that utility has been disabled by admins. My business users want to see this hierarchy in an easy-to-consume format. I was hoping that I won't have to program something like this from scratch because it seems like quite a common reporting requirement and the input data is simply formatted. My question is: is there a FOSS tool that takes standardized data input and produces such a hierarchical tree? Thanks

  Read the article

• Installing Xubuntu alongside with UEFI

  - by Geo

  For the past week and a half I have been trying to figure out how to install Xubuntu 13.10 alongside the Windows 7 install I have on my laptop (ASUS X501A with UEFI) and I'm pretty much at my wit's end. Could someone point me to set of thorough instructions on installing Xubuntu (or any of the Ubuntu derivatives) on a HDD under UEFI alongside Windows 7 64-bit Home Premium? Preferably one that also covers GRUB/bootloader problems that come afterwards. A few additional details: Motherboard does have UEFI. I've disabled Secure Boot and Fast Boot. Launch CSM is enabled and the platform keys are not installed (these settings allow me to at least boot Windows 7). I set the HDD's partition table to GPT through GParted before I installed Windows. I'm installing from a bootable USB that has been created through a tool called Rufus with the GPT partition scheme for UEFI computers option, otherwise I've left it at default. I am able to boot into Xubuntu in UEFI mode, but I'd much rather be able to see the option: Install Xubuntu Alongside Windows 7 (or however it's phrased), Xubuntu seems to be unable to recognize that Windows 7 is installed. I do have access to a bootable USB stick containing GParted though Xubuntu seems to come preinstalled with it. If there's anything else that might be of help, please let me know.

  Read the article

• GRUB2 not working after installing xubuntu 14.04

  - by h3bm

  I have a vaio laptop and it used to have installed windows 8 and Xubuntu 13.04 in dual boot, everything was working fine. I decided to update my version of xubuntu 14.04 LTS mainly because the support for 13.04 is finished and LTS version have 3 years of support. What I did was to format the partition where xubuntu 13.04 was installed and install 14.04 in that formated partition. When I restarted my computer willing to start using my new system I got the following message: error: symbol 'grub_term_highlight_color' not found and I was not able to enter any OS. I tried boot-repair from live USB more than two times and it did not fix the problem. I tried to enter to my computer using super GRUB2 disk, however it does not apperar to work with UEFI active (besides super grub2 disk says it can) I only get the message "no operating system found". If I boot super grub2 disk with UEFI disabled, super grub2 disk can not detect any OS,I also tried Rescatux distro, however, as of super grub2 disk, rescatux cannot enter when UEFI is active. I tried boot-repair with the option of "restore EFI backups", after that I was able to boot on windows, but no grub menu appeared. I ran boot-repair again with no improving results Here is the last Bootinfo report I got: http://paste.ubuntu.com/7609801/ Do you have any idea of what is happening? I really appreciate your help, Best regards,

  Read the article

• How to efficiently protect part of an application with a license

  - by Patrick

  I am working on an application that has many functional parts. When a customer buys the application, he buys the standard functionality, but he can also buy some additional elements of the application for an additional price. All of the elements are part of the same application executable. A license key is used to indicate which of the elements should be accessible in the application. Some of the elements can be easily disabled if the user didn't pay for it. These are typically the modules that you can access via the application's menu. However, some elements give more problems: What if a part of the data model is related to an optional part? Do I build up these data structures in my application so the rest of my application can just assume they're always there? Or do I don't build them, and add checks in the rest of may application? What if some optional part is still useful to perform some internal tasks, but I don't want to expose it to the user externally? What if the marketing responsible wants to make a standard part now an optional part? In all of my application I assume that that part is present, but if it becomes optional, I should add checks on it everywhere in the application. I have some ideas on how to solve some of the problems (e.g. interfaces with dual implementations: one working implementation, and one that is activated if the optional part is not activated). Do you know of any patterns that can be used to solve this kind of problem? Or do you have any suggestions on how to handle this licensing problem? Thanks.

  Read the article

• Nivida driver install

  - by Adham

  tried black listing and every thing i could find on the internet used with root and alt+ctrl+f1 with no solution nvidia-installer log file '/var/log/nvidia-installer.log' creation time: Mon Jun 17 08:35:25 2013 installer version: 319.23 PATH: /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin nvidia-installer command line: ./nvidia-installer Using: nvidia-installer ncurses user interface -> License accepted. -> Installing NVIDIA driver version 319.23. -> Running distribution scripts executing: '/usr/lib/nvidia/pre-install'... -> done. -> The distribution-provided pre-install script failed! Continue installation anyway? (Answer: Yes) ERROR: The Nouveau kernel driver is currently in use by your system. This driver is incompatible with the NVIDIA driver, and must be disabled before proceeding. Please consult the NVIDIA driver README and your Linux distribution's documentation for details on how to correctly disable the Nouveau kernel driver. WARNING: One or more modprobe configuration files to disable Nouveau are already present at: /etc/modprobe.d/nvidia-installer-disable-nouveau.conf. Please be sure you have rebooted your system since these files were written. If you have rebooted, then Nouveau may be enabled for other reasons, such as being included in the system initial ramdisk or in your X configuration file. Please consult the NVIDIA driver README and your Linux distribution's documentation for details on how to correctly disable the Nouveau kernel driver. ERROR: Installation has failed. Please see the file '/var/log/nvidia-installer.log' for details. You may find suggestions on fixing installation problems in the README available on the Linux driver download page at www.nvidia.com.

  Read the article

• ALPS touchpad stops working after reboot

  - by user58289

  I recently upgraded to 12.04 LTS. My Compaq Presario CQ-40 324la touchpad worked after first restarting after installation. But after restarting a second time, the touchpad is completely disabled, without having changed anything in the system. I've tried solutions but haven't had good results. The applications I've installed (fro "solutions" are: Pointing Devices Synaptiks Dconf-Tools I've also tried updating GRUB, adding this line: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash i8042.nomux") I tried these commands in a terminal. Neither has worked. sudo modprobe -r psmouse sudo modprobe psmouse proto=imps El Touchpad ALPS se desactiva al reiniciar Recién he actualizado a Ubuntu 12.04LTS y a mi parecer ha mejorado mucho con respecto a 11.10... Pero ese no es mi punto ahora. El Touchpad funcionó correctamente luego del primer reinicio después de la instalación. Pero luego de volver a reiniciar, el Touchpad queda totalmente deshabilitado sin haber hecho cambio alguno en el sistema. He probado las soluciones en su mayoría y no he tenido buenos resultados. Las aplicaciones que he instalado (de las "soluciones") son: -Dispositivos apuntadores. -Synaptiks -DConf-Tools Y he intentado también actualizando el grub (añadiéndole una linea así: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash i8042.nomux") Intenté en la terminal con el comando: sudo modprobe -r psmouse sudo modprobe psmouse proto=imps Ninguno me ha resultado bien. La laptop es Compaq Presario CQ-40 324la

  Read the article

• Electricsheep Not Working in Raring 13.04

  - by Nhoeh37

  I just downloaded Electricsheep four days before I updated my Ubuntu software and I fell in love with it. After I upgraded to 13.04, I'm kind of upset in saying that Electricsheep no longer works. I have no idea how to fix it and I feel helpless with Linux. As I said, it was working completely fine in 12.10, but now with the Raring Ringtail update: I use Xscreensaver to launch Electricsheep. When I open Xscreensaver, "Electricsheep" is one of the options to choose. When I "preview" ES or even launch the "xscreensaver-demo" in the terminal, it doesn't work anymore; I get an error message. The error message says: "detected another electric sheep process. rendering of sheep is disabled using read only access." Damnit, can someone please help me? I want my trippy screensaver back, it shouldn't be this hard! EDIT: I contacted the creator of Electricsheep (Scott Draves) via the link to his email address on his personal website and asked for his assistance. Hopefully the Askubuntu community will be able to fix this problem, I'm sure I am not the only one who is having this problem as I have searched and searched.

  Read the article

• 13.10 doesn't boot on Vaio Pro 13

  - by vaioonbuntu

  I just installed Ubuntu 13.10 on my new Vaio Pro 13, disabled safe mode, but used UEFI and not legacy mode. I did an encrypted LVM installation and erased the complete SSD. It booted just fine from USB, but after installation it doesn't boot. The Vaio failed boot screen appears. I then tried this advice here: 13.10 on vaio pro with UEFI sadly it fails for me with "/usr/sbin/grub-probe: error: failed to get canonical path of /cow." I then tried mounted the encrypted partition with Nautilus and tried this: Cannot update grub with paramters on live USB With /dev/sda2 and then to install GRUB to /dev/sda. Didn't succeed and warned me that the "GPT partition label contains no BIOS Boot Partition; embedding won't be possible" What do i have to do, go fix GRUB and be able to boot my finished install? Here's my Boot Repair Log: http://paste.ubuntu.com/6386598/ I would really appreciate any help, I'm so happy to finally be able to ditch my big fat Macbook Pro and use Ubuntu on my new, light Vaio Pro, if only I could fix GRUB. best, x

  Read the article

• Sound not working after installing PCI video card and then removing it

  - by bakhshu

  I am running 11.10 on a HP/Compaq Presario sr1010z, and the video/audio was working fine with whatever was in the machine already. Then I installed a new video card (PCI/nVidia), which disabled the audio/video on the old one automatically. But that card didn't work out too well so I removed it. Now the video is back to normal, but the audio is gone. I have tried the following: 1. In BIOS, set audio to on/enable rather than Auto 2. Looked for hardware in System Settings Sound, but nothing shows up there 3. But when I run the sysinfo utility, I get the description of the audio controller When I do a 'sudo aplay -l', I get 'aplay: device_list:240: no soundcards found...' And then when I do a 'lspci -v | grep -A7 -i "audio"' I get the following: 00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012 AC'97 Sound Controller (rev a0) Subsystem: Hewlett-Packard Company Device 2a05 Flags: bus master, medium devsel, latency 32, IRQ 5 I/O ports at a000 [size=256] I/O ports at a400 [size=128] Capabilities: 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Any ideas on how to fix this? Thanks

  Read the article

< Previous Page | 836 837 838 839 840 841 842 843 844 845 846 847  | Next Page >