Search Results

Search found 25123 results on 1005 pages for 'domain model'.

Page 856/1005 | < Previous Page | 852 853 854 855 856 857 858 859 860 861 862 863  | Next Page >

• DNS: how to get local server to superimpose results over authoritative server?

  - by growse

  I've got a domain for which the DNS I control, and is hosted on the internet. I also have a NAT'd internal network (192.168.0.0/24) which has internet access, and which I also control. On this internal network, I also have a DNS resolver. DNS software on both is PowerDNS. What I want to be able to do is for the DNS resolver on the internal network to be able to add/change records of queries and results that come down from the authoritative server. For example, the authoritative server might have a single record for animal.example.com: animal.example.com. IN AAAA 2001:140:283::1 However, I'd like it so that when internal clients do a dns lookup for animal.example.com, they might get back the following: animal.example.com. IN AAAA 2001:140:283::1 animal.example.com. IN A 192.168.0.2 Obviously, I could set up the internal DNS server to pretend to be authoritative for example.com, but that would require a fair bit of effort to keep the main DNS server and the internal DNS server in sync for the records which are the same between both. If the internal DNS server could somehow be made a slave of the main DNS server, but also have the provision to add its own results in, that would be ideal. Is this possible?

  Read the article

• Dell 2970 - HP 1/8 G2 autoloader keeps falling off LSI 2032 SCSI chain

  - by middaparka

  I've a somewhat irritating problem with a Dell 2970 that has a HP 1/8 G2 autoloader (the Ultrium LTO 2 model) attached to the Dell/LSI 2032 non-RAID SCSI card. In essence, sometimes the autoloader/drive completely fails to appear on the SCSI chain (i.e.: there's neither a media changer or tape drive present within the device manager) and sometimes it appears but then subsequently disappears at a seemingly random (yet always inconvenient) time, resulting in backup failures. On most occasions, there are simply no errors logged in the system event log, but I did manage to capture a series of LSI_SCSI event ID 11 ("The driver detected a controller error on \Device\RaidPort0") errors followed by an event ID 129, ("Reset to device, \Device\RaidPort0, was issued") error during testing. I've tried two different cables, both with the same effect – sometimes the autoloader appears (for a while), sometimes it's completely absent. There's only one terminator I've tried to use, but as I've since successfully tested the autoloader on multiple occasions (albeit via a Adaptec U160 card on a different machine), my gut feel is that the issue doesn't lie with the terminator, or indeed the autoloader itself. As such, I'm just wondering if anyone has any ideas? It's most likely not relevant, but this is all under Windows SBS 2008, running Backup Exec 12.5 SBS edition (the Dell version), both fully patched. Addidtionally, the autoloader is running the latest firmware. It's been a while since I've dealt with anything SCSI, so all suggestions will be gratefully, gratefully received.

  Read the article

• nginx config woes for multiple subdomains & domains

  - by Peter Hanneman

  I'm finally moving away from Apache and I've got the latest development version of nginx running on a fully updated Ubuntu 10.04 VPS. I've got a single dedicated IP for the box (1.2.3.4) but I've got two separate domains pointing to the server: www.example1.com and www.example2.net. I would like to map the fallowing relationships between urls and document roots in the config: www.example1.com / example1.com -> /var/www/pub/example1.com/ subdomain.example1.com -> /var/www/dev/subdomain/example1.com/ www.example2.net / example2.net -> /var/www/pub/example2.net/ subdomain.example2.net -> /var/www/dev/subdomain/example2.net/ Where the name of the requested subdomain is a folder under /var/www/dev/. Ideally a request for a non-existent subdomain(no matching folder found) would result in a rewrite to the public site (eg: invalid.example1.com -- www.example1.com) however a mere "404 Not Found" wouldn't be the worst thing in the world. It would also be nice if I didn't need to modify the config every time I mkdir a new subdomain folder - even better if I don't need to edit it for a new domain either...but now I'm getting greedy... :p Although in my defense Apache did all of this with a single directive. Does anyone know how I can efficiently mimic this behavior in nginx? Thanks in advance, Peter Hanneman

  Read the article

• Constant crashes in windows 7 64bit when playing games

  - by yx

  I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

  Read the article

• Postfix: Modify sender address based on recipient

  - by PJ P

  We have a Postfix server that receives mail from our application servers. Senders are in the form [email protected] (where host.fqdn can vary, depending on source server) and recipients can be internal or external users. Messages going to external users should have the sender changed to [email protected]. I have tried using canonical maps, but since that is handled by the cleanup daemon, before any transport decisions are made, it would affect all sender addresses. I have also tried creating a custom smtp transport with generic mappings and configuring transport_maps to use that custom smtp transport for external domains. However, generic mappings affect both sender and recipient addresses. Lastly, I've tried the following: Create a custom smtpd daemon that specifies sender canonical maps and a unique transport table. Send all externally addressed mail to that custom daemon. Ideally, sender canonical maps would transform the sender address and the unique transport table would relay messages to the internet. However, evidently, only one transport table can be used per Postfix instance. I want to avoid creating an entirely new Postfix instance to accommodate this rewriting. Any suggestions? (and thanks in advance)

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• Configuring DNS and IIS for multiple domains on a single server

  - by RichardS

  I might be over complicating this but...I am hosting several websites and dns for the domains on a single server: domain1.net domain1.com domain2.net I have three items which I'm trying to work out whether to achieve by DNS, by IIS hostnames(bindings), or by IIS redirect. 1. Where I have domain1.net and domain1.com, I want everything from both (all emails and web requests) to just point to the domain1.net. Can I do this at the DNS level, or do I have to set up the email as forwarders on the email server and the domain as a hostname in IIS? For example: [email protected] [email protected] www.domain1.com www.domain1.net 2. I want to make sure that requests for domain1.net and www.domain1.net both resolve to the same place. Should this be done with DNS or with multiple hostnames, or with IIS redirects? 3. If I then want to have one webmail site serving all of domains (webmail.domain1.net, webmail.domain2.net), is it best to this with a cname in DNS or with host headers in IIS?

  Read the article

• Using virtualization infrastructure for J2EE application distribution- viable alternative?

  - by Dan

  Our company builds custom J2EE web solutions. At the moment, we use standard J2EE distribution mechanisms (ear/war archives). Application servers are generally administered by our clients' IT departments and since we do not have complete control over the environment, a lot of entropy can be introduced into the solution. For example: latest app. server patch not applied conflicting third party libraries inside the app. server root server runtime and tuning parameters not configured (for example, number of connections in database pool) We are looking into using virtualization infrastructure for J2EE application distribution. Instead of sending the ear/war archive, we’d send image with application server node and our application preinstalled. Some of the benefits are same as using with using virtualization infrastructure in general, namely better use of hardware resources. For us, it reduces the entropy of hosting infrastructure - distributing VM should be less affected by hosting environment. So far, the downside I see can be in application server licenses, here they will have to use dedicated servers for our solution, but this is generally already done that way. Also, there is a complexity with maintaining virtualization infrastructure, but this is often something IT departments have more experience with than with administering and fine-tuning J2EE solutions. Anyone has experience with this model? What are the downsides? Will we not just replace one type of complexity with other?

  Read the article

• What's the best way to run Drupal and Django sites behind the same Varnish server?

  - by Alexis Bellido

  I have a high traffic website running with Drupal and Apache, five web servers behind a Varnish server load balancing. Let's say this site is example.com. I'm using five backends and a director like this in my default.vcl: director balancer round-robin { { .backend = web1; } { .backend = web2; } { .backend = web3; } { .backend = web4; } { .backend = web5; } } Now I'm working on a new Django project that will be a new section of this site running on example.com/new-section. After checking the documentation I found I can do something like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.backend = newbackend; } else { set req.backend = default; } } That is, using a different backend for a subdirectory /new-section under the same domain. My question is, how do I make something like this work with my director and load balancing setup? I'm probably going to run two or more web servers (backends) with my new Django project, each one with a mix of Gunicorn, Nginx, and a few Python packages, and would like to put all of those in their own Varnish director to load balance. Is it possible to do use the above approach to decide which director to use?, like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.director = newdirector; } else { set req.director = balancer; } } All suggestions welcome. Thanks!

  Read the article

• IIS 7.5 Warning : Cannot verify access to the path

  - by Mostafa

  I'm newbie in IIS 7.5 , Before this I used to run ASP.NET Website under IIS 5 , That was too easy . I'm trying to run a very simple asp.net website ( just created a new website from VS 2010 targeted in .net 3.5) in IIS 7.5.7600 on windows 7 Ultimate 64 bit . While adding application , during Test Setting i receive one warning that says : The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again But I don't know how to make sure application pool identity has read access to the physical path ? I'm wondering if there is any step by step article or some thing that show me the walk-though for running a simple asp.net website on IIS 7.5? I appreciate any help .

  Read the article

• Cannot log into Windows XP Embedded after changing computer name

  - by bignis

  Hi everyone, I purchased a tablet pc running Windows XP Embedded. The tablet was used in a medical clinic on a domain. For illustrative purposes, say the computer name was "COMPLEXCOMPUTERNAME". There was an administrator account, so I changed the password on account "COMPLEXCOMPUTERNAME\Administrator" to a blank password. I logged out and logged in successfully with the blank administrator password when the log-in dialog said "Log in to COMPLEXCOMPUTERNAME (this computer)". Next I renamed the computer from COMPLEXCOMPUTERNAME to SIMPLECOMPUTERNAME, which required a reboot. I did so, and I can't log in anymore. The log in screen still just says "Log in to COMPLEXCOMPUTERNAME (this computer)", but the account "COMPLEXCOMPUTERNAME\Administrator" no longer works. I suspect that this is because the computer has been renamed to SIMPLECOMPUTERNAME and it can no longer find the account. The "Log in to" dropdown can't be typed in, so I can't change the computer name Windows is trying to log into. I fear that I'm stuck. Is there a way I can get Windows to log into the computer name that I chose? Thanks! -Mike

  Read the article

• A-2-Z web hosting on Amazon AWS

  - by JDelage

  All, I am studying web dvp, and one of my classes is project-based. We have to build a functional site that demonstrate our understanding of: HTML, CSS, Javascript, php, MySQL, And potentially Ajax or some other web component. For the project, we can use a local server using WampServer and basically build the site entirely on our laptop. If I have time, I would like to create a real site, and I thought it would be a good way to familiarize myself with Amazon's AWS services. So if I purchase a domain name, can I rely on AWS to host the site from A-to-Z? I understand I can use AWS to host content, the database, and do the background computations, if needed. What else do I need and what are the parts that AWS cannot help me with? Second, is there good documentation for a beginner to navigate AWS and learn how to use it (either on Amazon, or some 3rd party sites, or even a good book, as long as is up to date). The ideal documentation would be a tutorial on creating a web site from a-to-z on AWS, as detailed as possible. As you can guess, I have limited understanding of the IT issues. I have 0 Linux or sysadmin experience, but this is a good opportunity to change that. I hope you can help me. Thank you, JDelage PS: Please keep the answers AWS-specific. At this point, I am only interested in alternative services to the extent that they plug a hole in Amazon's offering.

  Read the article

• postfix and iRedMail- Relaying Denied

  - by Lock

  I am trying to setup iRedMail and am way over my head here. I have installed it, and can send emails internally, but not externally. When I send an email from outside, I get the following return email: The error that the other server returned was: 550 550 5.7.1 <test@mailtest.domain.com.au>... Relaying denied (state 13). Now I have no idea where to start looking! Any ideas? I have really only just installed iRedMail so I am unsure what else I need to do to get it working. I've pointed my MX records to that server, so that shouldnt be the problem. Also- if i stop postfix (so nothing is listening on port 25) and send a test email, I get the same reply back. Why would I get the same reply back even if postfix is stopped? I have run tcpdump over 25 and can see the packets coming in/out, so its definitely a configuration issue! I suppose my question is not really "what is my problem", but more "What configuration needs to be completed on postfix and iRedMail?"

  Read the article

• RAM ok in memtest86+ == RAM ok after wake from sleep?

  - by twon33

  I have a Windows XP (32-bit) system that appears stable in normal operation, but was repeatably freezing (hard lock, no BSOD) a minute or so after waking from S3 sleep. Some Googling against the motherboard model and memory manufacturer suggested that I might need to bump up the memory voltage, so I tried it and it now seems to resume without freezing. However, I don't really trust it and I'd like to validate that it's actually stable, especially after resuming from sleep. I've run Prime95 for a few hours with no issues, and am planning an overnight run of Memtest86+, which I expect to pass because the system has been solid whenever I've run it without putting it to sleep. Does something like Memtest86+ exist that actually invokes S3 sleep during operation? Clearly it would need an operator to wake the computer to resume testing, but I don't think I've ever heard of a memory test tool that can do this. Alternately, am I wasting my time? Should a clean bill of health from Memtest86+ indicate stability regardless of whether sleep is involved, or, conversely, does my original problem indicate that Memtest86+ would have failed eventually with the stock voltage if I'd run it, sleep or not?

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• IIS 8 URL Redirect on site level

  - by jackncoke

  I am trying to do a simple 301 perm redirect to another url in IIS 8. The end results would be if i navigated to domain2.com i would end up on domain1.com. We are moving from IIS 6 to a new server and have aprox 600+ sites that will be configured on this IIS 8 box. All of these sites run a property CMS and are looking at the same directory for source code. In IIS 6 i would just go to the Home directory tab of each site and check the box that says "Permanent Redirect" and provide a URL. With IIS 8 there is "HTTP Redirect" and this looks like it would do the trick but it is being applied to all the sites in IIS 8. Not on the site level like it use to be in IIS 6. I also looked into URL Rewriting module for IIS 8 but it seems to take rules in the style of a firewall and i am not sure if i could effectly create rules that would cater to 600+ sites. I am looking for the easiest way to have redirects on my site level so that that customers with multiple domains can have there sites redirect to there main domain for seo purposes. I feel like this was so easily achieved in IIS 6 that i must be overlooking something in the new version.

  Read the article

• Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

  - by Wesley

  Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

  Read the article

• Getting SMB file shares working over a PPTP VPN

  - by Ben Scott

  I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to 127.0.0.1, and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else.

  Read the article

• WebDav System Error 67 in Windows XP

  - by Nixphoe

  Issue: I'm having issues getting WebDav to work in the command line on Windows XP, both Service Pack 2 and Service Pack 3. C:\>net use z: https://mywebsite.com/software/ System error 67 has occurred. The network name cannot be found. I have tested this with two webdav server. Both Ubuntu Apache and I Windows Server 2003 IIS. Both get the same result. Things That Haven't Worked: I've installed the following Microsoft KB on my XP machines with no avail. I've also found the following reg key: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WebClient\Parameters UseBasicAuth REG_DWORD 1 I try the following when trying to use a few work around I've dug up on the web, all producing the same result. net use z: https://mywebsite.com/software net use z: https://mywebsite.com/software# net use z: https://mywebsite.com/software/ net use z: https://mywebsite.com/software/# I've also tried all the above combinations adding a user into it /user:user and /user:user@domain. I've also tried using http:// rather than https://. I've tried "\\server.com@ssl:443\folder" I've gone over networking related issues as @WesleyDavid had pointed out. Things that do work: I can connect to the webdav folder via the URL and with mapping in Network Place, with XP. But the command line doesn't work (I need a drive letter). Windows 7 works perfectly with the same command. My Delemma: I need this to work with a drive letter. What else can I try to get this working?

  Read the article

• need advice on data center move, communication with both facilities during transition

  - by Brian Roden

  We are beginning the process of moving to a new facility. Office and warehouse operations will both be moving, and we must get shipping operations up and running at the new location while continuing to ship from the old location. Our contract with some third-party warehouse tenants requires two business day turnaround (only weekends and holidays excluded), so we can't have major downtime during the move. We would like to keep our 172.16.60/61.xxx internal address space in use throughout the move. Is it possible to keep using this same internal range, and have our existing WatchGuard Firebox 520 and whatever router we get for the other location (preferably the same model) just treat both locations as one network, leaving our host IPs the same throughout the move? Renumbering the servers when they move isn't a big deal, but our wireless terminals for order picking in the warehouse have fixed IPs (and a fixed IP, non-DNS reference to the host they speak with) and would be a massive undertaking to reconfigure when the servers move (each device would have to be reconfigured at least 2 times -- some when we start using them in the new building and the host is still here, all of them in both locations when the host moves to the new building, and the rest when they finally make the move to the new building). We're trying to avoid that if possible.

  Read the article

• Exchange SBS 2003 server stopped receiving mail over the weekend, senders getting "Relay access deni

  - by Charlie W.

  Firstly, I should say that I know my way around Windows very well, I don't really know the first thing about Exchange. I am trying to support a user that is running an SBS2003 Server with Exchange. Over the weekend, everyone sending something to any of his addresses gets an error message like the following: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 5.7.1 <[email protected]>: Relay access denied (state 14). ----- Original message ----- Received: by 10.114.18.7 with SMTP id 7mr5572745war.127.1275423472120; Tue, 01 Jun 2010 13:17:52 -0700 (PDT) MIME-Version: 1.0 Sender: [email protected] Received: by 10.143.10.15 with HTTP; Tue, 1 Jun 2010 13:17:32 -0700 (PDT) From: My Name <[email protected]> Date: Tue, 1 Jun 2010 15:17:32 -0500 X-Google-Sender-Auth: XiPrP8Em_6Eb94EH9m84nJVGvCY Message-ID: <[email protected]> Subject: TEST To: Client <[email protected]> Content-Type: multipart/alternative; boundary=001636b1484ffe72470487fdaa5b There are a host of errors in the Application log, but nothing that leaps out at me as being obvious. But then again, I don't really know what I'm looking for. Any help would be greatly appreciated.

  Read the article

• WMI Sensors monitoring

  - by DmitrySemenov

  Monitoring tool Paessler stopped to monitor WMI Windows Sensors Paessler is Updated to version 12.4.5.3165. (10/30/2012 1:44:11 PM) Paessler windows sensors (against windows server 2008 R2 web edition) stopped to work (no changes have been made on server that we monitor) with the message Connection could not be established (80070005: Access is denied - Host: 192.168.2.10, User: Administrator, Password: **, Domain: ntlmdomain:) (code: PE015) However if I go to Virtual machine used to run Paessler and the following cscript runs successfully: strComputer = "192.168.2.10" Set objSWbemLocator = CreateObject("WbemScripting.SWbemLocator") Set objSWbemServices = objSWbemLocator.ConnectServer _ (strComputer, "root\cimv2", _ "Administrator", "pass") Set colProcessList = objSWbemServices.ExecQuery( _ "Select * From Win32_Processor") For Each objProcess in colProcessList Wscript.Echo "Process Name: " & objProcess.Name Next I'm getting output C:\>cscript test.vbs Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz So WMI works a. I gave Administrator credentials for Device to monitor in Paessler setting, the same I used in the script above b. I restarted windows server (broken sensors) - but this didn't help c. I restarted Paessler probe service - no effect any ideas?

  Read the article

• Access Denied on Some Subfolders/Files Within a Share

  - by Tim

  First thing this morning, I find that users on one of our share drives are all getting "access denied". I tried the same drive and also received "access denied" as a Domain Admin. Previous to this, all specified users and admins could get access. I checked share permissions I checked NTFS permissions I temporarily made both types of permissions read/write to "Everyone" -- This worked for one user It turns out that this is occurring for only some files/folders. When I try to manually alter the share of that single share, it can't be shared, access denied. xcacls also gets access denied rebooted the server (not a big deal - this is a smallish company). Does anybody have any insight, my google-fu is coming up blank. Thanks. EDIT: More info, I just ran AccessEnum. There were a lot of "access denied", but I noticed the pattern that all of the access denied had a parent with an owner of "???". When I look at the properties, the "Unable to display owner" message is in the box and I can only make my user account the owner. I can then share the individual file/folder, but it doesn't seem to propogate down to subfolders/files.

  Read the article

• Registry remotley hacked win 7 need help tracking the perp

  - by user577229

  I was writing some .VBS code at thhe office that would allow certain file extensions to be downloaded without a warning dialog on a w7x32 system. The system I was writing this on is in a lab on a segmented subnet. All web access is via a proxy server. The only means of accessing my machine is via the internet or from within the labs MSFT AD domain. While writing and testing my code I found a message of sorts. Upon refresing the registry to verify my code changed a dword, instead the message HELLO was written and visible in regedit where the dword value wass called for. I took a screen shot and proceeded to edit my code. This same weird behavior occurred last time I was writing registry code except on another internal server. I understand that remote registry access exists for windows systems. I will block this immediately once I return to the office. What I want to know is, can I trace who made this connection? How would I do this? I suspect the cause of this is the cause of other "odd" behaviors I'm experiencing at work such as losing control of my input director master control for over an hour and unchanged code that all of a sudden fails for no logical region. These failures occur at funny times, whenver I'm about to give a demonstration of my test code. I know this sounds crazy however knowledge of the registry component makes this believable. Once the registry can be accessed, the entire system is compromised. Any help or sanity checking is appreciated.

  Read the article

• Are there any open source reseller packages?

  - by Tom Wright

  My department has just been given the right/responsibility to manage our own VPS. The idea being that the bureaucracy will be less for the many small web projects we run. Since each project will be managed by a different team, I was planning on approaching a shared hosting model. Are there any free pieces of software that would help automate the provision of resources each time a team request a new project? Most of the projects have identical requirements - basically LAMP - so it would be these resources that I would want provisioning (and de-provisioning, if that is a word) automatically. Ideally, there would also be a way to hook it into our LDAP authentication backend too, though I could probably make this sort of modification if necessary. Since we won't be charging our "client" however, we won't need the ability to generate invoices, handle payments, etc. etc. EDIT: Sample workflow Login authenticated against LDAP Username checked against admin group (not on central LDAP) Click 'new project' and enter project name User created on VPS with project name as username Apache virtual host created and subdomain (using project name) allocated FTP & MySQL users created

  Read the article

< Previous Page | 852 853 854 855 856 857 858 859 860 861 862 863  | Next Page >