Search Results

Search found 111524 results on 4461 pages for 'user mode linux'.

Page 87/4461 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• VLAN issues between linux kernels 2.6 / 3.3 in an ESX / Cisco environment

  - by David Griffith

  I shall attempt to explain an issue I have encountered - I have a VM running on esx 4.1 with an interface connected to VLAN800 via an access port on a cisco 3750. It runs linux - kernel 2.6.24, and has about 5 to 10 Mbit of chatter on 10.10.0.0/16 and various multicast addresses to look after. I needed to isolate certain devices from certain other devices on the network, with all of them having to talk to that one VM. No, the address space can't be separated, nor can the networks be easily vlan'd apart. The software on the VM listens to one interface only. Private vlans appear to be the way to go. So as a test, I built a bridge on the VM that globs together the vlans as needed. All good, everything works as expected. But occasionally (sigh) there's some latency that trips up a couple of profinet devices on the network because, you know, you're not really supposed to trunk real-time protocols around the place willy-nilly. I shift it to our test/backup server - works nicely, but I don't want it to be running on the test server as we muck around with that a lot. So I says to myself, "I'll put it on a new VM for testing and tweaking." I download a small linux distro with kernel 3.3, and install as a new VM with a the vlans as separate interfaces for testing. I power up the testing VM - ok. I bring up all the separate interfaces - ok. I can ping the production VM, see all sorts of traffic going past with tshark, etc. I build a bridge and put the primary vlan on it - the production VM running 2.6 immediately loses its multicast traffic - Unicast is fine. (?) I shut down the bridge - still no multicast traffic (!?) I power-cycle the production VM(!?!?) - multicast traffic returns. I trunk everything into the testing VM and create vlan interfaces under linux instead - same result, as soon as I start the bridge.... no multicast on the production VM. Ok, so I take a break and leave things alone. I decide to play with a couple of ubiquiti bullet radios - I'm testing various firmware as a side project. I flash a radio with Open-wrt-12.09. I enable a trunk on a port on a cisco on our network so I can muck around with multiple vlans and SSIDs I power up the radio and connect - ok. I create a vlan interface from the trunk.... the same vlan as the production VM wayyyyy over there, three cisco routers away. Ok. I bridge the vlan interface to the wifi interface and immediately get a phone call. The production VM has (suprise!) lost its multicast traffic. Again, nothing comes back until I power-cycle the VM. What the hell is going on?

  Read the article

• How to export user inputs (from python) to excel worksheet?

  - by mrn

  I am trying to develop a user form in python 2.7.3. Please note that I am a python beginner. I am trying to use xlwt to export data to excel. I want to write values of following variables i.e. a (value to write:'x1') & d (value to write: be user defined information in text box), a=StringVar() checkBox1=Checkbutton(root, text="text1", variable=a, onvalue="x1", offvalue="N/A") checkBox1.place(relx=0., rely=0., relwidth=0., relheight=0.) checkBox1.pack() d=StringVar() atextBox1=Entry(root, textvariable=d, font = '{MS Sans Serif} 10') atextBox1.pack() Need help badly. Thank you so much in advance

  Read the article

• Linux clients for Exchange (email and) calendar

  - by jplindstrom

  At $work, the official email solution is Outlook on Windows, connected to an Exchange server. That's problematic for people with Linux on their desktop machine. The Exchange server supports IMAP, and e-mail works fairly well using the usual suspects, e.g. Thunderbird. It also provides the web mail interface, which is fairly crap unless you use IE. (Any other favorite e-mail clients?) The biggest problem is the Outlook Calendar. I still have found no viable Linux client that can replace it. Any recommendations?

  Read the article

• Looking for KVM switch (over IP) with good linux client [closed]

  - by B14D3

  I have some ATEN CN6000 and i1708 KVM boxes and clients for them are made for windows and java. Java clients doesnt work neither on win or linux systems(I can run them with JavaRE but they dont connect to KVM box). Client for CN6000 on windows works quite well but a have huge problems with connect to i1708 with win client. So I'm looking for some good replacement. I'm aiming to KVM with linux client. Whether there are such ? What kind of KVMs you are using and have good opinion about them?

  Read the article

• user management in linux

  - by sdr

  what isThe difference between user management in Linux and networks with active directory?

  Read the article

• installing linux on an crippled machine

  - by networkbooter

  I have a somehwat ancient toshiba laptop (which cant boot from a usb) that i want to install linux on (ubuntu i guess). currently running windows XP and ubuntu (via wubi). I want to delete these OSs and replace with ubuntu only. it does have a network boot option - i was wondering if the easiet way is to steup some sort of network boot server on my other computer (which has ubunutu) and get the machine to boot from it so i can install linux? i cant seem to find instructions on the 'net as to how i would go about doing this... any pointers would be most appreciated. thanks!

  Read the article

• Linux command to inspect TXT records of a domain

  - by johnlai2004

  Is there a linux shell command that I can use to inspect the TXT records of a domain?

  Read the article

• SuperMicro BMC on OpenSuSE Linux --cannot access from LAN

  - by Kendall

  Hi, I have an (old) SMC-001 IPMI device on an (old) X6DVL-EG2 motherboard. My problem is that I cannot access the BMC from LAN. I'm also getting some interesting output from ipmitool. First, the setup. I enable Console Redirection in the BIOS, turn BIOS Redirection after POSt to "disabled". I then modprobe'ed for ipmi_msghandler, ipmi_devintf and ipmi_si. I then found ipmi0 under /dev. So far so good. Since I want console redirection over serial, I modified /boot/grub/menu.lst: http://pastebin.com/YYJmhusQ I then modified "/etc/inittab" as follows: S1:12345:respawn:/sbin/agetty -L 19200 ttyS1 ansi Networking I set as following, using "ipmitool" ipaddr: 192.168.3.164 netmask: 255.255.255.0 defgw: 192.168.3.1 The above are correct for my environment. To test it I do: ipmitool -I open chassis power off which responds by powering off the machine. When I to access from another computer on the network, however, I get an error message: host# ipmitool -I lanplus -H 192.168.10.164 -U Admin -a chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status "Admin" seems to be a valid user name: host# ipmitool -I open user list 1 2 Admin true false true USER The interesting output from ipmitool I initially mentioned: host # ipmitool -I open lan set 1 access on Set Channel Access for channel 1 failed: Request data field length limit exceeded Also, newload4:/home/gjones # ipmitool channel info 1 Channel 0x1 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : session-less Active Session Count : 0 Protocol Vendor ID : 7154 Get Channel Access (volatile) failed: Request data field length limit exceeded The output of "ipmitool -I open lan print 1" is here: http://pastebin.com/UZyL6yyE Any help/suggestions is greatly appreciated; I've been working with this thing for a few hours now with no success.

  Read the article

• How to add an SSH user to my Ubuntu 12 server to upload PHP files

  - by user229209

  I have an Ubuntu 12 VPS and wanted to create a user account to upload and download my PHP code. So when logged in as root I created a user "chris" and then created a directory /var/www/chris I want "chris" to be able to upload and run files to the /var/www/chris directory. Permissions for the chris dir look like this: drwxrwxr-x 2 root chris 4096 Aug 20 03:35 chris As root I created a sample file called abc.php and put it in the chris dir. It worked fine when I test it in a browser. I logged in as chris and uploaded a file called 1234.php. That did not work. I just got a blank PHP page. The code was identical in both files. So it is not the code. The permissions now look like this: -rw-r--r-- 1 root chris 59 Aug 20 03:34 1234.php -rw-r--r-- 1 root root 49 Aug 20 03:21 abc.php How do I alow the "chris" user to upload files and get them to work?

  Read the article

• Hardening non-root standalone Linux Tomcat install

  - by NoozNooz42

  I want to know if you have any tips as to how to strengthen the security of a non-root install of Tomcat in standalone mode once Tomcat is already installed in a non-root account, in standalone mode. I precise this because, for example, I'm not at all interested by the answers given here (because both Java and Tomcat requires root priviledges there to be installed and I've got zero interest in running jsvc): http://serverfault.com/questions/43765 So far, here's what I've done for my non-root standalone Tomcat 6 install: download and install the JRE .bin provided by Oracle/Sun (no need to be root here) (no need for a full JDK anymore right seen that Jasper [Tomcat's JSP engine] has its own compiler now right?) download and tar -xzf tomcat 6 (no need to be root here) set up transparent port-forwarding (must be root here) Note that my distribution is a Debian one and I have exactly zero interest in downloading Debian package / backports / whatever... Because, once again, I DO NOT want to need to be root to install Java & Tomcat. The only moment I needed to be root was to configure the firewall to transparently do the port forwarding 80 <-- 8080 and 443 <-- 8443. I then deleted all the default webapps but one: cd ~/apache-tomcat-6.0.26/webapps rm -rf docs rm -rf examples/ rm -rf manager/ rm -rf ROOT/ What about the directory ~/apache-tomcat-6.0.26/webapps/host-manager, do I need it or can I delete it? So, once I've installed Tomcat standalone in a non-root account (and taken into account that I don't want to enter the root password anymore and that I don't plan to install the whole Apache shebang), what more can I do? Are there connectors I can disable? (how?)

  Read the article

• LSI MegaRAID LINUX got Optimal after degradation but strange POST message

  - by kesrut

  Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

  Read the article

• Setfacl configuration issue in Linux

  - by Balualways

  I am configuring a Linux Server with ACL[Access Control Lists]. It is not allowing me to perform setfacl operation on one of the directoriy /xfiles. I am able to perform the setfacl on other directories as /tmp /op/applocal/. I am getting the error as : root@asifdl01devv # setfacl -m user:eqtrd:rw-,user:feedmgr:r--,user::---,group::r--,mask:rw-,other:--- /xfiles/change1/testfile setfacl: /xfiles/change1/testfile: Operation not supported I have defined my /etc/fstab as /dev/ROOTVG/rootlv / ext3 defaults 1 1 /dev/ROOTVG/varlv /var ext3 defaults 1 2 /dev/ROOTVG/optlv /opt ext3 defaults 1 2 /dev/ROOTVG/crashlv /var/crash ext3 defaults 1 2 /dev/ROOTVG/tmplv /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/ROOTVG/swaplv swap swap defaults 0 0 /dev/APPVG/home /home ext3 defaults 1 2 /dev/APPVG/archives /archives ext3 defaults 1 2 /dev/APPVG/test /test ext3 defaults 1 2 /dev/APPVG/oracle /opt/oracle ext3 defaults 1 2 /dev/APPVG/ifeeds /xfiles ext3 defaults 1 2 I have a solaris server where the vfstab is defined as cat vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - /dev/vx/dsk/bootdg/swapvol - - swap - no - swap - /tmp tmpfs - yes size=1024m /dev/vx/dsk/bootdg/rootvol /dev/vx/rdsk/bootdg/rootvol / ufs 1 no logging /dev/vx/dsk/bootdg/var /dev/vx/rdsk/bootdg/var /var ufs 1 no logging /dev/vx/dsk/bootdg/home /dev/vx/rdsk/bootdg/home /home ufs 2 yes logging /dev/vx/dsk/APP/test /dev/vx/rdsk/APP/test /test vxfs 3 yes - /dev/vx/dsk/APP/archives /dev/vx/rdsk/APP/archives /archives vxfs 3 yes - /dev/vx/dsk/APP/oracle /dev/vx/rdsk/APP/oracle /opt/oracle vxfs 3 yes - /dev/vx/dsk/APP/xfiles /dev/vx/rdsk/APP/xfiles /xfiles vxfs 3 yes - I am not able to find out the issue. Any help would be appreciated.

  Read the article

• iptables captive portal remove user

  - by Burgos

  I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

  Read the article

• Linux Startup Script after Gnome Login

  - by Eric

  I have a Fedora server that I want to spawn an interactive python script after the user logs on. This script will ask the user for various types of information for configuring the system or it will search for the previous config file and show them the predefined information. Originally I was going to put this in rc.local or make it run with init.d but that messed up the boot due to how the script is spawned. So I would like this script to run as soon as the user logs in to Gnome. I've searched around quite a bit and found this answer which appears to be exactly what I want, but it isn't working the way I want it to. Below is my entry. [Desktop Entry] Name=MyScript GenericName=Script for initial configuration Comment=I really want this to work Exec=/usr/local/bin/myscript.sh Terminal=true Type=Application X-GNOME-Autostart-enabled=true Whenever I login, nothing happens. So I then did a test to modified "myscript.sh" to just echo some text to a file and it worked fine. So it appears the portion that isn't working is the script popping open a terminal and waiting for the users input. Are there any additional options I need to add to make this work? I can confirm when I run /usr/local/bin/myscript.sh from the CLI it works fine. I have also tried adding "StartupNotify=true" and still no luck. Edit @John - I tried moving my Exec= to /usr/local/bin/myscript-test and this is what myscript-test contains. #!/bin/bash xterm -e /usr/local/bin/myscript.sh Yet again, when I just run the myscript-test it works fine. However when I put that in my autostart, nothing happens. Edit 2 - I did a few more tests and it did start working but I had to remove Terminal=True before the xterm would pop. Thanks for your help.

  Read the article

• Inheriting file ownership on linux

  - by John Hunt

  We have an ongoing problem here at work. We have a lot of websites set up on shared hosts, our cms writes many files to these sites and allows users of the sites to upload files etc.. The problem is that when a user uploads a file on the site the owner of that file becomes the webserver and therefore prevents us being able to change permissions etc via FTP. There are a few work arounds, but really what we need is a way to set a sticky owner if that's possible on new files and directories that are created on the server. Eg, rather than php writing the file as user apache it takes on the owner of the parent directory. I'm not sure if this is possible (I've never seen it done.) Any ideas? We're obviously not going to get a login for apache to the server, and I doubt we could get into the apache group either. Perhaps we need a way of allowing apache to set at least the group of a file, that way we could set the group to our ftp user in php and set 664 and 775 for any files that are written? Cheers, John.

  Read the article

• Finding the current user authenticated by basic auth (Apache)

  - by jtd

  When you log in through a basic auth page, is the username you authenticated as stored anywhere (on the server or client machine), maybe in an environment variable? Background: I have a common web administration page for an e-mail server and I'd like to know who is doing what. When a user successfully logs in via basic auth, I somehow want to be able to identify them and log their actions. So each time a request is submitted, I can write to a log file. The basic format would be: $username ran a $function against $useraccount so if a user changed someone's permissions, eg: Admin-Bob ran a permission change against User-Scott So if errors occur, I can easily trace back in the log file what actions lead to the cause. I tried checking the %ENV hash to no avail, any Ideas? I don't really want to get into PHP-like sessions, because that would mean scrapping my basic auth, which gives me a fine degree of control already. If I have to code something with sessions, I'd need to implement a system to block users after maximum tries and so on, which I don't really want to code. I think this is better geared towards serverfault because it pertains to Apache moreso than the programming language. Sessions can be done in a myriad of languages.

  Read the article

• proftpd initial directory for each user

  - by Dels

  After successfully setting up proftpd server, i want to add initial directory for each users, i have 2 user, webadmin that can access all folder and upload that can only access upload folder ... # Added config DefaultRoot ~ RequireValidShell off AuthUserFile /etc/proftpd/passwd # VALID LOGINS <Limit LOGIN> AllowUser webadmin, upload DenyALL </Limit> <Directory /home/webadmin> <Limit ALL> DenyAll </Limit> <Limit DIRS READ WRITE> AllowUser webadmin </Limit> </Directory> <Directory /home/webadmin/upload> <Limit ALL> DenyAll </Limit> <Limit DIRS READ WRITE> AllowUser upload </Limit> </Directory> All set ok, but i need to tell my ftp client initial directory for each user (otherwise it keep fail to retrieve directory), which i think it should be automatically set for each user (no need to type initial directory in ftp client)

  Read the article

• Limited bandwidth and transfer rates per user.

  - by Cx03

  I searched for a while but couldn't find anything concrete, hopefully someone can help me. I'm going to be running a Debian server on a gigabit port, and want to give each user his/her fair share of internet access. The first objective is easy - transfer rates (speed) per user. From what I've looked at, IPTables/Shorewall could do the job easy. Is this easy to setup, or could one of you point me at a config? I was hoping to limit users at 300mbit or 650mbit each. The second objective gets complicated. Due to the usage of the boxes, most of the traffic will be internal network traffic that does NOT get counted to the quota. However, I still need to limit the external traffic, and if they go over, cut off access (or throttle traffic to a very low speed (10mbit?)). Let's say the user has a 3TB external traffic limit. The IF part is: If the hostname they are exchanging the traffic with DOES NOT MATCH .ovh. or .kimsufi. (company owns multiple TLDs), count to the quota. Once said quota exceeds 3TB, choke them. Where could I find a system to count that for me? It would also need to reset or be able to be manually reset on a monthly basis. Thanks ahead of time!

  Read the article

• linux automatic change permissions in resolv.file

  - by rikr

  In various linux servers I see how the permissions of the /etc/resolv.conf file change automatically. In state normal: -r--r--r-- 1 root root 103 Jul 4 11:50 resolv.conf In changed state: -r--r----- 1 root root 103 Jul 4 11:50 resolv.conf I installed auditd for monitoring it, and these are the two entries between the change: type=PATH msg=audit(07/04/2012 12:20:02.719:303) : item=0 name=/etc/resolv.conf inode=137102 dev=fe:00 mode=file,644 ouid=root ogid=root rdev=00:00 type=CWD msg=audit(07/04/2012 12:20:02.719:303) : cwd=/ type=SYSCALL msg=audit(07/04/2012 12:20:02.719:303) : arch=x86_64 syscall=open success=yes exit=3 a0=7feeb1405dec a1=0 a2=1b6 a3=0 items=1 ppid=1585 pid=3445 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=(none) ses=4294967295 comm=hostid exe=/usr/bin/hostid key=(null) type=PATH msg=audit(07/04/2012 12:50:03.727:304) : item=0 name=/etc/resolv.conf inode=137102 dev=fe:00 mode=file,440 ouid=root ogid=root rdev=00:00 type=CWD msg=audit(07/04/2012 12:50:03.727:304) : cwd=/ type=SYSCALL msg=audit(07/04/2012 12:50:03.727:304) : arch=x86_64 syscall=open success=yes exit=3 a0=7f2bcf7abdec a1=0 a2=1b6 a3=0 items=1 ppid=1585 pid=3610 auid=unset uid=root gid=root euid=root suid=root fsuid=root egid=root sgid=root fsgid=root tty=(none) ses=4294967295 comm=hostid exe=/usr/bin/hostid key=(null) any ideas?

  Read the article

• How can I install things in Linux with *no yum* and *no wget*?

  - by e9t

  I'm a newbie to Linux (that mainly uses Windows and Mac OS X) needing some advice. I was trying to install git on a Linux machine today, and encountered some problems: Not knowing the version of the installed OS, I've opened the /proc/version file which said: Linux version 2.6.9-42.0.2.ELsmp ([email protected]) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Thu Aug 17 17:57:31 EDT 2006 Then, as written in the git documents (http://git-scm.com/download/linux), I assumed I could use the yum install git command for Fedora, but got the following result. [root@myserver ~]# yum install git -bash: yum: command not found So I tried installing yum using wget, but wasn't so lucky. [root@myserver ~]# wget http://linux.duke.edu/projects/yum/download/2.0/yum-2.0.7.tar.gz -bash: wget: command not found I googled and found this page and this page, so tried installing yum with rpm, but only got a result full of question marks. (Possibly an encoding problem, hmm...) [root@myserver ~]# rpm -Uvh http://www.eomy.net/linux/install-yum-x86_64/wget-1.10.2-0.40E.x86_64.rpm http://www.eomy.net/linux/install-yum-x86_64/wget-1.10.2-0.40E.x86_64.rpm(??)?? ?????? ?: /var/tmp/rpm-xfer.TbuAOu: V3 DSA signature: NOKEY, key ID 443e1821 ???.. ########################################### [100%] wget-1.10.2-0.40E U???????g??????? wget-1.10.2-0.40E???? ??g??/usr/bin/wget ?? wget-1.10.2-0.40E U?????? ???? wget-1.10.2-0.40E???? ??g??/usr/share/man/man1/wget.1.gz ?? wget-1.10.2-0.40E U?????? ???? [root@myserver ~]# Finally, when I typed rpm --version in the terminal, I got the below results. [root@myserver ~]# rpm --version RPM ???? - 4.3.3 I would like to know what I can do or possibly try now. Is it not possible to wget or yum anything in my situation? Or is there any magical tool like homebrew (http://mxcl.github.com/homebrew/) that I can use? Any comments or advice would be appreciated. Thanks in advance!

  Read the article

• Kernel Panic on VMware Workstation 7.1.3

  - by i.h4d35

  I've been trying to install either Arch Linux or Fedora 17 on VMWare Workstation (7.1.3). After I point to the right ISO image, I get the following error: Booting the kernel PANIC: early exception 0d rip:ffffffff81042dc4 error 0 cr2 0 I am trying to install it on a machine which has a 3rd generation i5 processor. After checking A VMWare panic early exception fix for ivy bridge i3, i5, i7, I tried to turn off the nosmep acpi. This is around, I get the same error but at a different address. Apparently, others have faced this issue before. Thanks in advance.

  Read the article

• Can't install kernel-uek-headers for currently running kernel

  - by haydenc2

  I have just created a VM in VMWare and installed a minimal install of Oracle Enterprise Linux 6.3. # cat /etc/oracle-release Oracle Linux Server release 6.3 It is running with the UEK kernel. # uname -r 2.6.39-200.24.1.el6uek.x86_64 When I try and install VMWare Tools, I get the following error. Searching for a valid kernel header path... The path "" is not a valid path to the 2.6.39-200.24.1.el6uek.x86_64 kernel headers. Would you like to change it? [yes] I have version 2.6.39 of the UEK installed, but the kernel-uek-headers are only 2.6.32. # yum list kernel-uek Installed Packages kernel-uek.x86_64 2.6.39-200.24.1.el6uek @anaconda-UEK2/6.3 kernel-uek.x86_64 2.6.39-200.29.3.el6uek @ol6_UEK_latest # yum list kernel-uek-headers Installed Packages kernel-uek-headers.x86_64 2.6.32-300.32.2.el6uek @ol6_latest And it appears that the headers for 2.6.39 aren't there. # yum list kernel-uek-headers --showduplicates Installed Packages kernel-uek-headers.x86_64 2.6.32-300.32.2.el6uek @ol6_latest Available Packages kernel-uek-headers.x86_64 2.6.32-100.28.5.el6 ol6_latest kernel-uek-headers.x86_64 2.6.32-100.28.9.el6 ol6_latest kernel-uek-headers.x86_64 2.6.32-100.28.11.el6 ol6_latest kernel-uek-headers.x86_64 2.6.32-100.28.15.el6 ol6_latest kernel-uek-headers.x86_64 2.6.32-100.28.17.el6 ol6_latest kernel-uek-headers.x86_64 2.6.32-100.34.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-100.35.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-100.36.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-100.37.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-200.16.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-200.19.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-200.20.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-200.23.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.3.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.4.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.7.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.11.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.20.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.21.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.24.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.25.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.27.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.29.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.29.2.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.32.1.el6uek ol6_latest kernel-uek-headers.x86_64 2.6.32-300.32.2.el6uek ol6_latest The kernel for 2.6.32 is there. # yum list kernel-uek --showduplicates Installed Packages kernel-uek.x86_64 2.6.39-200.24.1.el6uek @anaconda-UEK2/6.3 kernel-uek.x86_64 2.6.39-200.29.3.el6uek @ol6_UEK_latest Available Packages kernel-uek.x86_64 2.6.32-100.28.5.el6 ol6_latest kernel-uek.x86_64 2.6.32-100.28.9.el6 ol6_latest kernel-uek.x86_64 2.6.32-100.28.11.el6 ol6_latest kernel-uek.x86_64 2.6.32-100.28.15.el6 ol6_latest kernel-uek.x86_64 2.6.32-100.28.17.el6 ol6_latest kernel-uek.x86_64 2.6.32-100.34.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-100.35.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-100.36.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-100.37.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-200.16.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-200.19.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-200.20.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-200.23.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.3.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.4.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.7.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.11.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.20.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.21.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.24.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.25.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.27.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.29.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.29.2.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.32.1.el6uek ol6_latest kernel-uek.x86_64 2.6.32-300.32.2.el6uek ol6_latest kernel-uek.x86_64 2.6.39-100.5.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-100.6.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-100.7.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-100.10.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-200.24.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-200.29.1.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-200.29.2.el6uek ol6_UEK_latest kernel-uek.x86_64 2.6.39-200.29.3.el6uek ol6_UEK_latest Should I downgrade the kernel to 2.6.32 so I can install VMWare tools? Is there another way to get the kernel-uek-headers package for the 2.6.39 UEK?

  Read the article

• LightDM will not start after stopping it

  - by Sweeters

  I am running Ubuntu 11.10 "Oneiric Ocelot", and in trying to install the nvidia CUDA developer drivers I switched to a virtual terminal (Ctrl-Alt-F5) and stopped lightdm (installation required that no X server instance be running) through sudo service lightdm stop. Re-starting lightdm with sudo service lightdm start did not work: A couple of * Starting [...] lines where displayed, but the process hanged. (I do not remember at which point, but I think it was * Starting System V runlevel compatibility. I manually rebooted my laptop, and ever since booting seems to hang, usually around the * Starting anac(h)ronistic cron [OK] log line (not consistently at that point, though). From that point on, I seem to be able to interact with my system only through a tty session (Ctrl-Alt-F1). I've tried purging and reinstalling both lightdm and gdm, as well as selecting both as the default display managers (through sudo dpkg-reconfigure [lightdm / gdm] or by manually editing /etc/X11/default-display-manager) through both apt-get and aptitude (that shouldn't make a difference anyway) after updating the packages, but the problem persists. Some of the responses I'm getting are the following: After running sudo dpkg-reconfigure lightdm (but not ... gdm) I get the following message: dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_NAME missing dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_PACKAGE missing After trying sudo service lightdm start or sudo start lightdm I get to see the boot loading screen again but nothing changes. If I go back to the tty shell I see lightdm start/running, process <num> but ps -e | grep lightdm gives no output. After trying sudo service gdm start or sudo starg gdm I get the gdm start/running, process <num> message, and gdm-binary is supposedly an active process, but all that happens is that the screen blinks a couple of times and nothing else. Other candidate solutions that I'd found on the web included running startx but when I try that I get an error output [...] Fatal server error: no screens found [...]. Moreover, I made sure that lightdm-gtk-greeter is installed but that did not help either. Please excuse my not including complete outputs/logs; I am writing this post from another computer and it's hard to manually copy the complete logs. Also, I've seen several posts that had to do with similar problems, but either there was no fix, or the one suggested did not work for me. In closing: Please help! I very much hope to avoid re-installing Ubuntu from scratch! :) Alex @mosi I did not manage to fix the NVIDIA kernel driver as per your instructions. I should perhaps mention that I'm on a Dell XPS15 laptop with an NVIDIA Optimus graphics card, and that I have bumblebee installed (which installs nvidia drivers during its installation, I believe). Issuing the mentioned commands I get the following: ~$uname -r 3.0.0-12-generic ~$lsmod | grep -i nvidia nvidia 11713772 0 ~$dmesg | grep -i nvidia [ 8.980041] nvidia: module license 'NVIDIA' taints kernel. [ 9.354860] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354864] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354868] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.354873] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.354879] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.355052] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 280.13 Wed Jul 27 16:53:56 PDT 2011 Also, running aptitude search nvidia gives me the following: p nvidia-173 - NVIDIA binary Xorg driver, kernel module a p nvidia-173-dev - NVIDIA binary Xorg driver development file p nvidia-173-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-173-updates-dev - NVIDIA binary Xorg driver development file p nvidia-96 - NVIDIA binary Xorg driver, kernel module a p nvidia-96-dev - NVIDIA binary Xorg driver development file p nvidia-96-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-96-updates-dev - NVIDIA binary Xorg driver development file p nvidia-cg-toolkit - Cg Toolkit - GPU Shader Authoring Language p nvidia-common - Find obsolete NVIDIA drivers i nvidia-current - NVIDIA binary Xorg driver, kernel module a p nvidia-current-dev - NVIDIA binary Xorg driver development file c nvidia-current-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-current-updates-dev - NVIDIA binary Xorg driver development file i nvidia-settings - Tool of configuring the NVIDIA graphics dr p nvidia-settings-updates - Tool of configuring the NVIDIA graphics dr v nvidia-va-driver - v nvidia-va-driver - I've tried manually installing (sudo aptitude install <package>) packages nvidia-common and nvidia-settings-updates but to no avail. For example, sudo aptitude install nvidia-settings-updates returns the following log: Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 83 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used. Writing extended state information... Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... The same happens with the Linux headers (i.e. I cannot seem to be able to install linux-headers-3.0.0-12-generic). The output of aptitude search linux-headers is as follows: v linux-headers - v linux-headers - v linux-headers-2.6 - i linux-headers-2.6.38-11 - Header files related to Linux kernel versi i linux-headers-2.6.38-11-generic - Linux kernel headers for version 2.6.38 on i A linux-headers-2.6.38-8 - Header files related to Linux kernel versi i A linux-headers-2.6.38-8-generic - Linux kernel headers for version 2.6.38 on v linux-headers-3 - v linux-headers-3.0 - v linux-headers-3.0 - i A linux-headers-3.0.0-12 - Header files related to Linux kernel versi p linux-headers-3.0.0-12-generic - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-generic- - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-server - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-virtual - Linux kernel headers for version 3.0.0 on p linux-headers-generic - Generic Linux kernel headers p linux-headers-generic-pae - Generic Linux kernel headers v linux-headers-lbm - v linux-headers-lbm - v linux-headers-lbm-2.6 - v linux-headers-lbm-2.6 - p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-serv - Header files related to linux-backports-mo p linux-headers-server - Linux kernel headers on Server Equipment. p linux-headers-virtual - Linux kernel headers for virtual machines @heartsmagic I did try purging and reinstalling any nvidia driver packages, but it did not seem to make a difference, My xorg.conf file contains the following: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 ([email protected]) Wed Jul 27 17:15:58 PDT 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• How do I fix dependency problems with the kernel in apt?

  - by Jon

  When trying to install new packages, either manually or with muon, I get these errors: jon@jon-desktop:~/Apps/mendeleydesktop-1.5-dev4-linux-x86_64/bin$ sudo apt-get install kupfer [sudo] password for jon: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: kupfer : Depends: python-keybinder but it is not going to be installed Recommends: python-wnck but it is not going to be installed linux-headers-generic : Depends: linux-headers-3.2.0-20-generic but it is not installable linux-image-generic : Depends: linux-image-3.2.0-20-generic but it is not installable E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). jon@jon-desktop:~/Apps/mendeleydesktop-1.5-dev4-linux-x86_64/bin$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: linux-generic linux-headers-generic linux-image-generic The following packages will be upgraded: linux-generic linux-headers-generic linux-image-generic 3 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 3 not fully installed or removed. Need to get 0 B/6,658 B of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? dpkg: dependency problems prevent configuration of linux-image-generic: linux-image-generic depends on linux-image-3.2.0-20-generic; however: Package linux-image-3.2.0-20-generic is not installed. dpkg: error processing linux-image-generic (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. dpkg: dependency problems prevent configuration of linux-generic: linux-generic depends on linux-image-generic (= 3.2.0.20.22); however: Package linux-image-generic is not configured yet. dpkg: error processing linux-generic (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. dpkg: dependency problems prevent configuration of linux-headers-generic: linux-headers-generic depends on linux-headers-3.2.0-20-generic; however: Package linux-headers-3.2.0-20-generic is not installed. dpkg: error processing linux-headers-generic (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: linux-image-generic linux-generic linux-headers-generic E: Sub-process /usr/bin/dpkg returned an error code (1) As indicated above, I ran sudo apt-get -f install but it still tells me there are dependency issues.

  Read the article

• Running a small IPTV station

  - by nixterrimus

  I'm looking to run an iptv station for my dorm. I know I can serve multicast so that's not a problem. The station will serve out podcasts and other cc licensed content. The target endpoint is xbmc- a media center. So far I know that I need to serve an rtp stream over udp that's streaming an mpeg-4 avc main or high profile with aac ( or ac3 ?) audio. I've had some luck using vlc with vlm to stream but it seems limited. What are my other options?  Everything has to run on Linux- hopefully open source. How can I use playlists and not live streams? What are my software options?

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >