Search Results

Search found 57810 results on 2313 pages for 'http delete'.

Page 872/2313 | < Previous Page | 868 869 870 871 872 873 874 875 876 877 878 879  | Next Page >

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• SCVMM 2008 R2 problems migrating VM from VS2005 to Hyper-V host

  - by Scott Ivey

  I have System Center Virtual Machine Manager 2008 R2 installed, and have a Hyper-V R2 host and a Virtual Server 2005 host. I'm trying to migrate my machines from the VS2005 host to the Hyper-V host, and keep getting the following error... VMM is unable to complete the requested file transfer. The connection to the HTTP server myserver.mydomain.local could not be established. (Unknown error (0x80072efd)) Recommended Action Ensure that the HTTP service and/or the agent on the machine myserver.mydomain.local are installed and running and that a firewall is not blocking HTTPS traffic. (Note - migrations between Hyper-V hosts managed by the VMM server work fine - my problem is just going from VS2005-Hyper-V hosts) I have no firewalls turned on on either of the servers, and no firewalls in the middle. I've looked all over for answers to this problem, and am getting nowhere. All the articles I find when searching are talking about either V2V or P2V - and i'm just trying to do a straight migrate VM. I've tried rebooting the boxes, changing the BITS SSL port number, restarting services, triple-checking firewalls, etc. Does anyone have any good suggestions as to how I can resolve this problem?

  Read the article

• snort with barnyard2 not working on Fedora 12

  - by aHunter

  Has anyone come across this error with barnyard2 and snort? --== Initializing Barnyard2 ==-- Initializing Input Plugins! Initializing Output Plugins! Parsing config file "/etc/snort/barnyard2.conf" Log directory = /var/log/barnyard2 database: compiled support for (mysql) database: configured to use mysql database: schema version = 107 database: host = localhost database: user = test database: database name = snort database: sensor name = localhost:eth0 database: sensor id = 1 database: data encoding = hex database: detail level = full database: ignore_bpf = no database: using the "log" facility --== Initialization Complete ==-- ______ -*> Barnyard2 <*- / ,,_ \ Version 2.1.8 (Build 251) |o" )~| By the SecurixLive.com Team: http://www.securixlive.com/about.php + '''' + (C) Copyright 2008-2010 SecurixLive. Snort by Martin Roesch & The Snort Team: http://www.snort.org/team.html (C) Copyright 1998-2007 Sourcefire Inc., et al. WARNING: Ignoring corrupt/truncated waldofile '/var/log/snort/barnyard.waldo' Opened spool file '/var/log/snort/snort.log.1282004944' ERROR: Unknown record type read: 104 Fatal Error, Quitting.. Snort seems to be working correctly as I have managed to get logs via syslog but when I try to use the barnyard config via Unified2 it is not working. Presumably because of the above error. Thanks in advance.

  Read the article

• stunnel not working - stunnel.pem: No such file or directory

  - by Marronsuisse

  I am trying to install stunnel on an amazon LINUX machine. (i want to configure postfix so that it sends its emails through amazon ses) I first tried to install from the tar.gz package download from http://www.stunnel.org and installed with the commands: ./configure make make install but than the stunnel command was still not found. Then I installed with yum install stunnel. But now when I try I get: sudo stunnel 2012.06.23 06:51:53 LOG7[20071:3078289200]: Snagged 64 random bytes from /root/.rnd 2012.06.23 06:51:53 LOG7[20071:3078289200]: Wrote 1024 new random bytes to /root/.rnd 2012.06.23 06:51:53 LOG7[20071:3078289200]: RAND_status claims sufficient entropy for the PRNG 2012.06.23 06:51:53 LOG7[20071:3078289200]: PRNG seeded successfully 2012.06.23 06:51:53 LOG3[20071:3078289200]: stunnel.pem: No such file or directory (2) So it seems there is still a problem with the install. When I use the locate stunnel command, I see files a bit everywhere. How can I do to have a clean install of stunnel? Edit: i was following this procedure: http://docs.amazonwebservices.com/ses/latest/DeveloperGuide/SMTP.MTAs.SecureTunnel.html when I got stuck at point 5 and got the stunnel.pem: No such file or directory message.

  Read the article

• How do I access the web server on my desktop from my laptop?

  - by Steven

  I'm running Apache on my stationary and I would like to access a website through my laptop. This is some of the Apache config: NameVirtualHost 127.0.0.1:80 <VirtualHost 127.0.0.1:80> ServerName mysite.com DocumentRoot I:/wamp/www/mysite/ </VirtualHost> ServerName localhost:80 <Directory /> Options FollowSymLinks AllowOverride all Order deny,allow Deny from all </Directory> On my laptop I've added the following to the HOSTS file: 10.0.0.3 mysite.com But accessing the page through mysite.com is not very successfull. If I enter the IP address directly, I only get a Forbidden message. What do I need to do in order to get this to work? Update I'm runing WAMPSERVER 2.1 (Apache 2.2.17) Apache is up and running I can ping 10.0.0.3 from laptop I'm not able to ping http://mysite.com from laptop IE gives me a 403 Forbidden - The website declined to show this webpage The only log that get's entries when trying to access the website from my laptop, is access.log. access.log 10.0.0.4 - - [13/Jun/2011:10:14:04 +0200] "GET / HTTP/1.1" 403 202 apache_error.log [Mon Jun 13 10:08:16 2011] [error] VirtualHost localhost:0 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results UPDATE 2 My apache config has the following entry: AllowOverride all Order Deny,Allow Deny from all Allow from 127.0.0.1 Could it be that this Allow from is stopping other computers accessing the page?

  Read the article

• Configure ApacheDS 1.5 with accessControlEnabled=true for authenticated access

  - by cmyers

  I need to set up an apacheDS instance. I am using standalone 1.5.5 on Linux. I have removed the example partition and added two of my own, each with their own suffixes. I have imported LDIFs for the two partitions and everything looks correct data-wise. I need to configure ApacheDS to disallow anonymous access. I was able to do that by following some of the directions here: http://directory.apache.org/apacheds/1.5/145-enable-and-disable-anonymous-access.html http://directory.apache.org/apacheds/1.5/32-basic-authorization.html Now only the administrator account (uid=admin,ou=system) can log in and make queries. I need to establish an admin account, and a "regular user" account which can read and write only certain entries within each partition. I tried to read the above docs and I got nuthin'. The second page "basic authorization" is completely incomprehensible to me. When I tried to add a "prescriptiveACI" to it using Apache Directory Studio, I get: Administration point 2.5.4.11=abc,2.5.4.10=efg does not contain an administrativeRole attribute! An administrativeRole attribute in the administrative point is required to add a subordinate subentry. where my partition is "ou=abc,o=def". I have no clue what is going on and the docs are really not helping, I am at a complete loss here. How can it possibly be this hard to just restrict access? P.S. can someone with proper rep please change the tag "apache" to the new tag "ApacheDS"?

  Read the article

• Where should CentOS users get /usr/share/virtio-win/drivers for virt-v2v?

  - by Philip Durbin

  I need to migrate a number of virtual machines from VMware ESX to CentOS 6 KVM hypervisors. Ultimately, I wrote an RPM spec file that solved my problem at https://github.com/fasrc/virtio-win/blob/master/virtio-win.spec but I'm not sure if there's another RPM in base CentOS or EPEL (something standard) I should be using instead. Originally, I was getting this "No root device found in this operating system image" error when attemting to migrate a Window 2008 VM. . . [root@kvm01b ~]# virt-v2v -ic 'esx://my-vmware-hypervisor.example.com/' \ -os transferimages --network default my-vm virt-v2v: No root device found in this operating system image. . . . but I solved this with a simply yum install libguestfs-winsupport since the docs say: If you attempt to convert a virtual machine using NTFS without the libguestfs-winsupport package installed, the conversion will fail. Next I got an error about missing drivers for Windows 2008. . . [root@kvm01b ~]# virt-v2v -ic 'esx://my-vmware-hypervisor.example.com/' \ -os transferimages --network default my-vm my-vm_my-vm: 100% [====================================]D virt-v2v: Installation failed because the following files referenced in the configuration file are required, but missing: /usr/share/virtio-win/drivers/amd64/Win2008 . . . and I resolved this by grabbing an iso from Fedora at http://alt.fedoraproject.org/pub/alt/virtio-win/latest/ as recommended by http://www.linux-kvm.org/page/WindowsGuestDrivers/Download_Drivers and building an RPM from it with this spec file: https://github.com/fasrc/virtio-win/blob/master/virtio-win.spec Now, virt-v2v exits without error: [root@kvm01b ~]# virt-v2v -ic 'esx://my-vmware-hypervisor.example.com/' \ -os transferimages --network default my-vm my-vm_my-vm: 100% [====================================]D virt-v2v: my-vm configured with virtio drivers. [root@kvm01b ~]# Now, my question is, rather that the virtio-win RPM from the spec file I wrote, is there some other more standard RPM in base CentOS or EPEL that will resolve the error above? Here's a bit more detail about my setup: [root@kvm01b ~]# cat /etc/redhat-release CentOS release 6.2 (Final) [root@kvm01b ~]# rpm -q virt-v2v virt-v2v-0.8.3-5.el6.x86_64 See also Bug 605334 – VirtIO driver for windows does not show specific OS: Windows 7, Windows 2003

  Read the article

• HLS video segmenting complications. How to create a transport stream with ffmpeg

  - by Agzam

  I have h264 videos, and currently we're using Apple's HTTP Video Streaming tools and mediafilesegmenter to segment these files. What I need to do is to switch to alternative segmenter based on this very popular open-sourced segmenter The problem is that this segmenter does not just take any video, but takes only MPEG-TS videos. So I have to convert my h264 videos to TS first. I can do that with ffmpeg. I'm using this: ffmpeg -i encoded.mp4 -vcodec h264 -i encoded.mp4 -sameq -acodec aac -strict experimental -f mpegts output.ts But this creates fairly larger output. And the reason is that Apple's segmenter keeps the same codec - AVC and the same audio codec - AAC, whereas ffmpeg changes video format to MPEG Video. The question is: can I somehow keep the same AVC video codec and still convert video to a transport stream? So my goal is to keep the same video quality and same video codecs as Apple's medifilesegmenter does. UPD: Okay... it seems that ffmpeg CAN split videos into segments: ffmpeg -i encoded.mp4 -c copy -map 0 -vbsf h264_mp4toannexb -f segment -segment_time 10 -segment_list test.m3u8 -segment_format mpegts segment%d.ts That's still has one problem: it doesn't create http live streaming index file. (-segment_list creates a file with list of segments, but it doesn't look like HLS index). So, you still have to create index file

  Read the article

• How to Creat custom content for nginx error 502 page, keep origin url on browser

  - by user123862

  i'm trying to get custom language and message for nginx error page but keep url on browser.. not success for eg: i go to url : xaluan.com/aaa/bbb.html on the time server down.. nginx will show error 502. with the same url but custom message as my language. test 1. I created a custom page at /usr/local/nginx/html/205.html as following config but it show on web site when error is default nginx error at domain.com/50.html ( the content of webpage not same as i created) error_page 502 /502.html; location = /502.html { root /usr/local/nginx/html; } test 2. Then i create same page at my www domain folder /home/xaluano/public_html/502.html but this keep redirect me to root domain.com/502.html the content now same as i created. but.. the url still not as i need error_page 502 /502.html; location = /502.html { root /home/xaluano/public_html; internal; } EDIT UPDATE for more detail 10/06/2012 please download my nginx config http://pastebin.com/7iLD6WQq and vhost config following: http://pastebin.com/ZZ91KiY6 == the case test.. if apache httpd service stop: #service httpd stop then open browser go to: xaluan.com/modules.php?name=News&file=article&sid=123456 I will see the 502 error with the same url on browser address == Custome error page I need the config which help when apache fail .. will show the custom message tell user wail for 1 minute for service back then refress current page with same url ( refresh I can do easy by javascript ), Nginx dosent change url so java-script can work out. any help will be great.. thank in advance

  Read the article

• Apache & SVN on Ubuntu - Post-commit hook fails silently, pre-commit hook “Permission Denied”

  - by 113169587962668775787

  I've been struggling for the past couple days to get post-commit email notifications working on my SVN server (running via HTTP with Apache2 on Ubuntu 9.10). SVN commits work fine, but for some reason the hooks are not being properly executed. Here are the configuration settings: - Users access the repo via HTTP with the apache dav_svn module (I created users/passwords via htpasswd in a dav_svn.passwd file). dav_svn.conf: <Location /svn/repos> DAV svn SVNPath /home/svn/repos AuthType Basic AuthName "Subversion Repository" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user </Location> I created a post-commit hook file that writes a simple message to a file in the repository root: /home/svn/repos/hooks/post-commit: #!/bin/sh REPOS="$1" REV="$2" /bin/echo 'worked' > ${REPOS}/postcommit.log I set the entire repository to be owned by www-data (the apache user), and assigned 755 permissions to the post-commit script when I test the post-commit script using the www-data user in an empty environment, it works: sudo -u www-data env - /home/svn/repos/hooks/post-commit /home/svn/repos 7 But when I commit on a client machine, the commit is successful, but the post-commit script does not seem to be executed. I also tried running a simple script for the pre-commit hook, and I get an error, even with an empty pre-commit script: "Commit failed (details follow): Can't create null stdout for hook '/home/svn/repos/hooks/pre-commit': Permission denied" I did a few searches on Google for this error and I presume that this is an issue with the apache user (www-data) not having adequate permissions, specifically to execute /dev/null. I also read that the reason post-commit fails silently is because that it doesn't report with stdout. Anyway, I've also tried giving the apache user (www-data) ownership of the entire repository, and edited the apache virtualhost to allow operations on the server root, and I'm still getting permission denied /etc/apache2/sites-available/primarydomain.conf <Directory /> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> Any ideas/suggestions would be greatly appreciated! Thanks

  Read the article

• Staying anonymous while hosting your site?

  - by jamesCroft

  I don't mean anonymous surfing. I mean hosting and having your own domain and such. The reason is that my blog is about religious/political topics which may cause me trouble in the future. This is the domain I am working on: www.james-croft.com I know that using Whois search my name can come up: http://www.networksolutions.com/whois-search/james-croft.com The solution to that, as far as I understood, is to buy a privacy package from the domain registrar. in my case it is lucky register: http://i.stack.imgur.com/uvOdc.png Also hosting is a concern. I use the same hosting service for multiple websites. My question is this: Can my hosting be tracked and be used to identify me? Also: Are there other methods of finding out my identity from either Google Adsense or Amazon affiliate programs? I couldn't find any relevant articles online. If there is anything else that is relevant, please let me know. I appreciate any response.

  Read the article

• MemCache-repcached compile error

  - by Ramy Allam

  I'm trying to install [memcached-1.2.8-repcached-2.2.1]( http://sourceforge.net/projects/repcached/files/latest/download?source=files) And I have the following error after running the make command: make all-recursive make[1]: Entering directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1' Making all in doc make[2]: Entering directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1/doc' make[2]: Nothing to be done for `all'. make[2]: Leaving directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1/doc' make[2]: Entering directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1' gcc -DHAVE_CONFIG_H -I. -DNDEBUG -g -O2 -MT memcached-memcached.o -MD -MP -MF .d eps/memcached-memcached.Tpo -c -o memcached-memcached.o test -f 'memcached.c' || echo './'memcached.c memcached.c: In function ‘add_iov’: memcached.c:697: error: ‘IOV_MAX’ undeclared (first use in this function) memcached.c:697: error: (Each undeclared identifier is reported only once memcached.c:697: error: for each function it appears in.) make[2]: * [memcached-memcached.o] Error 1 make[2]: Leaving directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1' make[1]: * [all-recursive] Error 1 make[1]: Leaving directory `/usr/local/src/pro/memcached-1.2.8-repcached-2.2.1' make: * [all] Error 2 OS : Centos5.7 64bit gcc-4.1.2-51.el5 gcc-c++-4.1.2-51.el5 libgcc-4.1.2-51.el5 Note : Memcached and memcache extension for php are already installed root@server[~]# memcached -h memcached 1.4.5 php ext http://pecl.php.net/get/memcache-2.2.6.tgz

  Read the article

• SSH session closing whilst virtualenv session stays open (I think)

  - by ing0

  I've been developing some sites using Flask recently (running on debian within a virtualenv), and when I am testing I can run it on a port, let's say post 5000. So I run the script like so: . env/bin/activate <- go into virtual environment python file.py <- run python script And I will be given this message: Running on http://0.0.0.0:5000/ So this all works great and I can access my site on this port fine. However... my rubbish ISP always does this thing where it resets something around 1am every morning. I have no idea what this is, everything runs like normal but I always get disconnected from any SSH sessions open. This leaves it running and all I can do is call: lsof -i Which will show me the process but if I kill it and then rerun it things get weird. The: Running on http://0.0.0.0:5000 message still shows but I cannot connect to it anymore. I've tried changing the port number and it seems the only thing that works is trying again later on or on another day. Now I'm assuming that something on my server resets inbetween these times and I would like to think it was maybe that virtualenv session timing out, but I cannot find out how to do this manually, does anyone know?

  Read the article

• Node.js, Nginx and Varnish with WebSockets

  - by Joe S

  I'm in the process of architecting the backend of a new Node.js web app that i'd like to be pretty scalable, but not overkill. In all of my previous Node.js deployments, I have used Nginx to serve static assets such as JS/CSS and reverse proxy to Node (As i've heard Nginx does a much better job of this / express is not really production ready). However, Nginx does not support WebSockets. I am making extensive use of Socket.IO for the first time and discovered many articles detailing this limitation. Most of them suggest using Varnish to direct the WebSockets traffic directly to node, bypassing Nginx. This is my current setup: Varnish : Port 80 - Routing HTTP requests to Nginx and WebSockets directly to node Nginx : Port 8080 - Serving Static Assets like CSS/JS Node.js Express: Port 3000 - Serving the App, over HTTP + WebSockets However, there is now the added complexity that Varnish doesn't support HTTPS, which requires Stunnel or some other solution, it's also not load balanced yet (Perhaps i will use HAProxy or something). The complexity is stacking up! I would like to keep things simpler than this if possible. Is it still necessary to reverse proxy Node.js using Nginx when Varnish is also present? As even if express is slow at serving static files, they should theoretically be cached by Varnish. Or are there better ways to implement this?

  Read the article

• nginx 301 redirect to subfolder on primary domain

  - by 187j3x1

  hello there, sorry for my poor english. i just set up wordpress on my vps, so far its the only item on my site. there for seo reason, i think is better redirect all primary domain to the blog folder. primary domain is example.com wordpress is at example.com/blog what i want is rewrite www.example.com and example.com to example.com/blog. googled got some scripts, and make some change paste into nginx config file. here is: #301 redirect www to non-www server { server_name www.example.com; location = / { rewrite ^/(.*) http://example.com/$1 permanent; } } #301 non-www to subfolder server { server_name example.com; location = / { rewrite ^/(.*) http://example.com/blog$1 permanent; } } it works at some degree, successfully redirect to example.com/blog. the only problem is i get 404 not found error. then i only make nginx redirect www to example.com/blog. ok, this time i can access blog page. i know there is something wrong in the non-www to subfolder script. but do not how to fix it :(

  Read the article

• ZFS - destroying deduplicated zvol or data set stalls the server. How to recover?

  - by ewwhite

  I'm using Nexentastor on a secondary storage server running on an HP ProLiant DL180 G6 with 12 Midline (7200 RPM) SAS drives. The system has an E5620 CPU and 8GB RAM. There is no ZIL or L2ARC device. Last week, I created a 750GB sparse zvol with dedup and compression enabled to share via iSCSI to a VMWare ESX host. I then created a Windows 2008 file server image and copied ~300GB of user data to the VM. Once happy with the system, I moved the virtual machine to an NFS store on the same pool. Once up and running with my VMs on the NFS datastore, I decided to remove the original 750GB zvol. Doing so stalled the system. Access to the Nexenta web interface and NMC halted. I was eventually able to get to a raw shell. Most OS operations were fine, but the system was hanging on the zfs destroy -r vol1/filesystem command. Ugly. I found the following two OpenSolaris bugzilla entries and now understand that the machine will be bricked for an unknown period of time. It's been 14 hours, so I need a plan to be able to regain access to the server. http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6924390 and http://bugs.opensolaris.org/bugdatabase/view_bug.do;jsessionid=593704962bcbe0743d82aa339988?bug_id=6924824 In the future, I'll probably take the advice given in one of the buzilla workarounds: Workaround Do not use dedupe, and do not attempt to destroy zvols that had dedupe enabled. Update: I had to force the system to power off. Upon reboot, the system stalls at Importing zfs filesystems. It's been that way for 2 hours now.

  Read the article

• missing network usage through iptables

  - by Purres

  I inserted a rule to iptables to track the input usage to a certain ip address. The vps server's IP is 192.168.1.5 and the guest os's IP is 192.168.1.115. I ran 'yum update' inside the guest OS to get some network traffic. Then I ran iptables -vnL from the hypervisor. However it only showed network usage to the host, but not to the guest. Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target source destination 0 0 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.115-192.168.1.115 1853 114K 0.0.0.0/0 0.0.0.0/0 destination IP range 192.168.1.5-192.168.1.5 I ran tcpdump and the log showed that there're data packets to the guest os. 16:17:43.932514 IP mirrordenver.fdcservers.net.http > 192.168.1.115.34471: Flags [.], seq 17694667:17696115, ack 1345, win 113, options [nop,nop,TS val 1060308643 ecr 1958781], length 1448 16:17:43.932559 IP 192.168.1.115.34471 > mirrordenver.fdcservers.net.http: Flags [.], ack 17696115, win 15287, options [nop,nop,TS val 1958869 ecr 1060308643], length 0 Why the guest OS network usage couldn't be tracked? iptables -L will return the INPUT chain as following: Chain INPUT (policy ACCEPT) target prot opt source destination all -- anywhere anywhere destination IP range 192.168.1.115-192.168.1.115 all -- anywhere anywhere destination IP range 192.168.1.5-192.168.1.5 all -- anywhere anywhere

  Read the article

• How should secret files be pushed to an EC2 (on AWS) Ruby on Rails application?

  - by nikc

  How should secret files be pushed to an EC2 Ruby on Rails application using amazon web services with their elastic beanstalk? I add the files to a git repository, and I push to github, but I want to keep my secret files out of the git repository. I'm deploying to aws using: git aws.push The following files are in the .gitignore: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb Following this link I attempted to add an S3 file to my deployment: http://docs.amazonwebservices.com/elasticbeanstalk/latest/dg/customize-containers.html Quoting from that link: Example Snippet The following example downloads a zip file from an Amazon S3 bucket and unpacks it into /etc/myapp: sources: /etc/myapp: http://s3.amazonaws.com/mybucket/myobject Following those directions I uploaded a file to an S3 bucket and added the following to a private.config file in the .elasticbeanstalk .ebextensions directory: sources: /var/app/current/: https://s3.amazonaws.com/mybucket/config.tar.gz That config.tar.gz file will extract to: /config/database.yml /config/initializers/omniauth.rb /config/initializers/secret_token.rb However, when the application is deployed the config.tar.gz file on the S3 host is never copied or extracted. I still receive errors that the database.yml couldn't be located and the EC2 log has no record of the config file, here is the error message: Error message: No such file or directory - /var/app/current/config/database.yml Exception class: Errno::ENOENT Application root: /var/app/current

  Read the article

• KVM work with bridge network problems

  - by isware

  I try to configure bridge network for KVM(refer to http://www.linux-kvm.org/page/Networking), and it worked for Guest OS, but I have two problems with my Fedora host OS: 1?I can not access internet on host 2?The bridge configuration lost after reboot, I need to execute "service network restart" again to bring it up I checked here(http://serverfault.com/questions/168119/kvm-network-bridge-with-public-static-ip-for-both-host-and-guests) for the first problem, it seems not working for me. Any advice is appreciated! ifconfig -a eth0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:231340 errors:0 dropped:0 overruns:0 frame:0 TX packets:413424 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:15335606 (14.6 MiB) TX bytes:114755796 (109.4 MiB) Interrupt:44 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:119307 errors:0 dropped:0 overruns:0 frame:0 TX packets:119307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:57151264 (54.5 MiB) TX bytes:57151264 (54.5 MiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) sw0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet addr:192.168.1.133 Bcast:255.255.255.255 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:229584 errors:0 dropped:0 overruns:0 frame:0 TX packets:401232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11047463 (10.5 MiB) TX bytes:113891533 (108.6 MiB) tap0 Link encap:Ethernet HWaddr F2:86:1A:48:E2:55 inet6 addr: fe80::f086:1aff:fe48:e255/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232 errors:0 dropped:0 overruns:0 frame:0 TX packets:2744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:24842 (24.2 KiB) TX bytes:243899 (238.1 KiB) virbr0 Link encap:Ethernet HWaddr 9A:7C:09:6B:85:65 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:46 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5513 (5.3 KiB)

  Read the article

• Apache Derby running in Tomcat shutdown issues

  - by Luke

  I have set up Derby Network Server to be hosted within a Tomcat environment. This works great. However, when I shut down Tomcat I get the following errors: 04/01/2011 10:41:41 AM org.apache.catalina.core.StandardService stop INFO: Stopping service Catalina 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesJdbc SEVERE: The web application [/derby] registered the JBDC driver [org.apache.derby.jdbc.ClientDriver] but failed to unregister it when the web application was stopped. To prevent a memory leak, the JDBC Driver has been forcibly unregistered. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesJdbc SEVERE: The web application [/derby] registered the JBDC driver [org.apache.derby.jdbc.AutoloadedDriver] but failed to unregister it when the web application was stopped. To prevent a memory leak, the JDBC Driver has been forcibly unregistered. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [derby.NetworkServerStarter] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [NetworkServerThread_4] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [DRDAConnThread_5] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.catalina.loader.WebappClassLoader clearReferencesThreads SEVERE: The web application [/derby] appears to have started a thread named [DRDAConnThread_13] but has failed to stop it. This is very likely to create a memory leak. 04/01/2011 10:41:41 AM org.apache.coyote.http11.Http11Protocol destroy INFO: Stopping Coyote HTTP/1.1 on http-8080 I'm currently starting and stopping Tomcat with the following commands: ./catalina run ./catalina stop Is there a better way to shutdown Tomcat with Derby or can this be solved by a configuration change?

  Read the article

• Hosting a javascript api file for third party sites the way sharethis, uservoice, analytics do it.

  - by Dayson

  I'm preparing to launch a service soon which will provide third party websites a widget. The widget requires my javascript file in the website's code. Exactly the same way services like analytics, uservoice, sharethis, getclicky, etc provide you with a javascript snippet to add to your page. Therefore, my javascript file is going to be hotlinked by tons of websites which possibly receive a lot of requests too. I need advice/opinions on the following aspects: What's the right location for hosting this file? Should I use a sub-domain for it? I was thinking of something like http://api.myservice.com/js/foo.js . Remember, once websites start embedding this file, its location CANNOT change under any circumstances. Right now we can afford just one dedicated server. So I have minified my file, enabled gzip and plan to use some good cache control headers through apache. Also, in the near future when the requests pickup, I will use a http proxy like Varnish. Is this a good plan for the near future? Should I be considering a CDN in the future (since we can't afford it now)? If so how do I make sure we're prepared to migrate to it without breaking services. Pros/Cons of moving just this file to a CDN? Also, since its just one javascript file(50kb), any affordable CDN so we could consider it in the beginning itself? Any other word of advice I could use? Anything I shouldn't overlook at this stage which I would regret later? (both in terms of server + javascript ajax limitations) Thanks in advance.

  Read the article

• Need help with some IIS7 web.config compression settings.

  - by Pure.Krome

  Hi folks, I'm trying to configure my IIS7 compression settings in my web.config file. I'm trying to enable HTTP 1.0 requests to be gzip. MSDN has all the info about it here. Is it possible to have this config info in my own website's web.config file? Or do i need to set it at an application level? Currently, I have that code in my web.config... <system.webServer> <urlCompression doDynamicCompression="true" dynamicCompressionBeforeCache="true" /> <httpCompression cacheControlHeader="max-age=86400" noCompressionForHttp10="False" noCompressionForProxies="False" sendCacheHeaders="true" /> ... other stuff snipped ... </system.webServer> It's not working :( HTTP 1.1 requests are getting compressed, just not 1.0. That MSDN page above says that it can be used in :- Machine.config ApplicationHost.config Root application Web.config Application Web.config Directory Web.config So, can we set these settings on a per-website-basis, programatically in a web.config file? (this is an Application Web.config file...) What have i done wrong? cheers :) EDIT: I was asked how i know HTTP1.0 is not getting compressed. I'm using the Failed Request Tracing Rules, which reports back:- DYNAMIC_COMPRESSION_START DYNAMIC_COMPRESSION_NOT_SUCESS Reason: 3 Reason: NO_COMPRESSION_10 DYNAMIC_COMPRESSION_END

  Read the article

• Macbook Pro 2010 Ethernet Jumbo Frame(9k MTU) Support?

  - by Troggy

  Has anyone been able to use jumbo frame support on their 2010 Macbook Pros? This is kind of negative news here, but I am seeing many reports that this is not available anymore due to Apple's choice of network card in the new machines. I cannot set my MTU speed over 1500 on my new 2010 MBP i7, but my old early 2008 MBP (Core2) has the 9000 MTU setting for use. Everything I have is setup to use jumbo frames and I thought apple kept that feature in their "pro" lineup. It sounds like the Mac Pro still has it. Did they decide to use a chipset that doesn't support it? I am trying to pinpoint some solid chipset numbers and the feature support. Maybe they just need to update the drivers? Is there some more official information about this feature? This might seem minor, but this is really frustrating if apple removed this feature from their pro laptop line. From what I have read so far, it sounds like I am not alone in my frustrations with this. http://discussions.info.apple.com/message.jspa?messageID=12258067 http://discussions.apple.com/thread.jspa?messageID=12130158 Anyone have any experience or further knowledge about this issue ... beyond typing my question into google and giving the top 5 results as answers? :)

  Read the article

• Cannot start listening on a certain TCP port, but there's nothing currently listening on it

  - by John Rasch

  I have Windows Service that uses a WCF service host to listen for connections on TCP port 61000. When I try to start the service, I get the error: Service cannot be started. System.ServiceModel.AddressAlreadyInUseException: HTTP could not register URL http://+:61000/ because TCP port 61000 is being used by another application. ---> System.Net.HttpListenerException: The process cannot access the file because it is being used by another process at System.Net.HttpListener.AddAll() at System.Net.HttpListener.Start() at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() --- End of inner exception stack trace --- at System.ServiceModel.Channels.SharedHttpTransportManager.OnOpen() at System.ServiceModel.Channels.TransportManager.Open(TransportChannelListener channelListener) at System.ServiceModel.Channels.TransportManagerContainer.Open(SelectTransportManagersCallback selectTransportManagerCallback) at System.ServiceModel.Channels.HttpChannelListener.OnOpen(TimeSpan timeout) at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout) at System.ServiceModel.Dispatcher.ChannelDispatcher.OnOpen(TimeSpan timeout) at... A quick netstat -a shows there is nothing listening on port 61000. I've also found several posts online that mention reserving namespaces using netstat, but the account that the service runs under has administrator privileges so that shouldn't be necessary. Any other ideas as to why I'm getting this message? This service is running on 64-bit Windows Server 2008 R2 Standard.

  Read the article

• remote telnet and email

  - by Mustafa Ismail Mustafa

  This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

  Read the article

< Previous Page | 868 869 870 871 872 873 874 875 876 877 878 879  | Next Page >