Search Results

Search found 26098 results on 1044 pages for 'self build'.

Page 879/1044 | < Previous Page | 875 876 877 878 879 880 881 882 883 884 885 886  | Next Page >

  • WDS updating raid drivers in an already existing image WIM

    - by Tim
    Here is my current setup. WDS installed on Server 2008 R2 for the new driverstore and multicast features. A Windows Server 2003 32bit Standard image built to support previous DL360 models. A new HP DL360 G6 which has a new raid controller in it. I need to add the driver for the raid controller into my Server 2003 32bit standard install image but I can't seem to figure out the correct method to do so. So far I've tried the following: Mounting the image and placing the drivers into the Sysprep drivers folder, adding the PCI device codes into the sysprep.inf file and committing the changes to the image. Pushing the image to a DL360 G4, ensuring the driver is in the correct locations and re-sysprepping the image. Hoping that the new driverstore feature would magically work with 2003 (a guy can dream cant he?) Is there some standard method that I can use to update this image with the new drivers or do I need to start from scratch with an entirely new build? Thanks in advance.

    Read the article

  • Citrix Access Gateway with Citrix Receiver

    - by vm370
    I'm currently using a Citrix Access Gateway with firmware 5.0.4 to provide access over an SSL-VPN to an isolated environment, which is connected to over the Citrix Access Gateway Client, which is delivered by the device by default. However we encountered different problems, e.g. that it's somehow not possible to get it out of the autostart (not registered as a service or in the autostart?!) and it killed the Cisco VPN Client, which is used in the company and unfortunately cannot be replaced. The Cisco client can also just be used again after a procedure with cleaning the registry from all CAG Client remains, which requires a lot of effort. Because of that, I'd like to check if there is an alternative to this client, since is this is a real pain... Unfortunately I couldn't find a way to use the Receiver with the CAG yet, but if you have any resources on how to build this workaround, I'd be very happy. Thanks a lot in advance UPDATE: If there are other alternatives I'd be even more happy, since using the Receiver would also mean that there is an issue with the ICA-Client, which is also used in our environments. From my experience, the Receiver and the ICA-Client are also no good friends...

    Read the article

  • Apache Won't Restart After Compiling PHP with Postgres

    - by gonzofish
    I've compiled PHP (v5.3.1) with Postgres using the following configure: ./configure \ --build=x86_64-redhat-linux-gnu \ --host=x86_64-redhat-linux-gnu \ --target=x86_64-redhat-linux-gnu \ --program-prefix= \ --prefix=/usr/ \ --exec-prefix=/usr/ \ --bindir=/usr/bin/ \ --sbindir=/usr/sbin/ \ --sysconfdir=/etc \ --datadir=/usr/share \ --includedir=/usr/include/ \ --libdir=/usr/lib64 \ --libexecdir=/usr/libexec \ --localstatedir=/var \ --sharedstatedir=/usr/com \ --mandir=/usr/share/man \ --infodir=/usr/share/info \ --cache-file=../config.cache \ --with-libdir=lib64 \ --with-config-file-path=/etc \ --with-config-file-scan-dir=/etc/php.d \ --with-pic \ --disable-rpath \ --with-pear \ --with-pic \ --with-bz2 \ --with-exec-dir=/usr/bin \ --with-freetype-dir=/usr \ --with-png-dir=/usr \ --with-xpm-dir=/usr \ --enable-gd-native-ttf \ --with-t1lib=/usr \ --without-gdbm \ --with-gettext \ --without-gmp \ --with-iconv \ --with-jpeg-dir=/usr \ --with-openssl \ --with-zlib \ --with-layout=GNU \ --enable-exif \ --enable-ftp \ --enable-magic-quotes \ --enable-sockets \ --enable-sysvsem \ --enable-sysvshm \ --enable-sysvmsg \ --with-kerberos \ --enable-ucd-snmp-hack \ --enable-shmop \ --enable-calendar \ --with-libxml-dir=/usr \ --enable-xml \ --with-system-tzdata \ --with-mime-magic=/usr/share/file/magic \ --with-apxs2=/usr/sbin/apxs \ --with-mysql=/usr/include/mysql \ --without-gd \ --with-dom=/usr/include/libxml2/libxml \ --disable-dba \ --without-unixODBC \ --disable-pdo \ --enable-xmlreader \ --enable-xmlwriter \ --without-sqlite \ --without-sqlite3 \ --disable-phar \ --enable-fileinfo \ --enable-json \ --without-pspell \ --disable-wddx \ --with-curl=/usr/include/curl \ --enable-posix \ --with-mcrypt \ --enable-mbstring \ --with-pgsql=/mnt/mv/pgsql I'm using Postgres 8.4.0 and Apache 2.2.8; I have the following line in my Apache conf file: LoadModule php5_module /usr/lib64/httpd/modules/libphp5.so And when I attempt to restart Apache, I get the following error message: Starting httpd: httpd: Syntax error on line 205 of /etc/httpd/conf/httpd.conf: Cannot load /usr/lib64/httpd/modules/libphp5.so into server: /usr/lib64/httpd/modules/libphp5.so: undefined symbol: lo_import_with_oid Now, I know that this is a problem with Postgres with PHP because lo_import_with_oid is a function in the Postgres source which allows the importing of large objects; also, if I remove the --with-pgsql option, PHP and Apache get along great. I've scoured the Internet looking for answers all day, but to no avail. Does anyone have ANY insight into what is causing my problems.

    Read the article

  • Unable to stop chrome.exe *32

    - by chipperyman573
    So I was installing roboform today and was unable to stop the process chrome.exe *32... Even when I uninstalled chrome. This is the error I got: I used lockhunter and it said it was located in %appdata%\Local\Google\Chrome. However, it was unable to unlock, delete or rename. When I use explorer to delete or rename that folder, it says it's being used by Chrome. Even after restarting my computer it still does this. I've tried using the built in chrome task manager (Wrench View Background Pages) and I can't seem to find a process there that has the same amount of memory. I have run many, many virus scans, by: Microsoft security essentials AVG (Free version) Malwarebytes (Pro version) Norton 360 (Pro version) McAfee (Pro Version) Avira (Free version) Avast! Antivirus (Free version) None of which returned with any viruses. Chrome info: Google Chrome 23.0.1271.95 (Official Build 169798) OS Windows 7 Professional WebKit 537.11 (@135931) JavaScript V8 3.13.7.5 Flash 11.5.31.2 User Agent Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11

    Read the article

  • Trying to install ffmpeg-php and having installation issues.

    - by dallasclark
    I've installed ffmpeg successfully using the ffmpeginstaller 3 series (http://www.ffmpeginstaller.com/download). ffmpeg is working fine without any known issues with bash. The ffmpeginstaller is meant to install ffmpeg-php but it cannot be found and I receive an error when I execute php -v PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/ffmpeg.so' - /usr/lib64/php/modules/ffmpeg.so: cannot open shared object file: No such file or directory in Unknown on line 0 Looking at the '/usr/lib64/php/modules/' folder, it doesn't contain the ffmpeg.so file. I've tried to install ffmpeg-php manually but I receive the following error checking for ffmpeg headers... configure: error: ffmpeg headers not found. Make sure you've built ffmpeg as shared libs using the --enable-shared option Should I install ffmpeg with series 4 or 5 of ffmpeginstaller or does someone know how to fix this issue? Thanks in advance ! System Specs cat /etc/redhat-release CentOS release 5.5 (Final) cat /proc/version Linux version 2.6.18-028stab068.5 (root@rhel5-64-build) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 php -v PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/ffmpeg.so' - /usr/lib64/php/modules/ffmpeg.so: cannot open shared object file: No such file or directory in Unknown on line 0 PHP 5.2.13 (cli) (built: Mar 2 2010 18:08:48) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2010 Zend Technologies Any other details you need, just let me know.

    Read the article

  • Network monitoring tools with API features

    - by Kev
    We use ks-soft's Advanced Hostmonitor package to monitor around 2000 items on our network. We think it's great, the chap that supports it is fantastic, the product is fast, stable and mature but I feel as as we grow as a company it's beginning to show some friction points in the area of integration with our back office admin systems. One of the things we'd like to do is be able to add new tests to whatever monitoring tool we use via an API. For example, when orders for servers come from our retail interface, the server gets built automatically, and as part of the automated build process we'd like to automatically add new tests to the network monitoring systems. Hostmonitor has some support for this via a feature called HM Script but we're starting to encounter some speedbumps - we can't add new operators/users we can't define new "Action Profiles" - these are the actions to be taken when a test goes good or bad. What we love about hostmonitor though are the Action Profiles. For example if a Windows IIS box goes bad our action profile for a bad test does something like: Check host again (one time) Wait another 30 seconds then test again Try restart app pool on remote machine (up to two times) Send an email to ops about the restart failure Try restarting IIS on remote machine (up to four times) Page duty admin (up to 5 times - stops after duty admin ACKS alert) Page backup duty admin (5 times - stops after duty admin ACKS alert) I'm starting to look around at other network monitoring tools and I'm looking for: a comprehensive API to be able to add/remove/control tests/test "action profiles"/operators (not just plugins, we need control and admin interfaces) the ability to have quite detailed action/escalation profiles (and define these via an API) I've looked at Nagios and Icinga but Ican't seem to glean from their documentation whether we could have these features or not, or if we could, how much work would be involved to implement/customise. Can anyone provide any advice, guidance or experiences?

    Read the article

  • Graphite SQLite3 DatabaseError: attempt to write a readonly database

    - by Anadi Misra
    Running graphite under apache httpd, with slqite database, I have the correct folder permissions [root@liaan55 httpd]# ls -ltr /var/lib | grep graphite drwxr-xr-x. 2 apache apache 4096 Aug 23 19:36 graphite-web and [root@liaan55 httpd]# ls -ltr /var/lib/graphite-web/ total 68 -rw-r--r--. 1 apache apache 65536 Aug 23 19:46 graphite.db syncdb also seems to have gone fine [root@liaan55 httpd]# sudo -su apache bash-4.1$ whoami apache bash-4.1$ python /usr/lib/python2.6/site-packages/graphite/manage.py syncdb /usr/lib/python2.6/site-packages/graphite/settings.py:231: UserWarning: SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security warn('SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security') /usr/lib/python2.6/site-packages/django/conf/__init__.py:75: DeprecationWarning: The ADMIN_MEDIA_PREFIX setting has been removed; use STATIC_URL instead. "use STATIC_URL instead.", DeprecationWarning) /usr/lib/python2.6/site-packages/django/core/cache/__init__.py:82: DeprecationWarning: settings.CACHE_* is deprecated; use settings.CACHES instead. DeprecationWarning Creating tables ... Creating table account_profile Creating table account_variable Creating table account_view Creating table account_window Creating table account_mygraph Creating table dashboard_dashboard_owners Creating table dashboard_dashboard Creating table events_event Creating table auth_permission Creating table auth_group_permissions Creating table auth_group Creating table auth_user_user_permissions Creating table auth_user_groups Creating table auth_user Creating table django_session Creating table django_admin_log Creating table django_content_type Creating table tagging_tag Creating table tagging_taggeditem You just installed Django's auth system, which means you don't have any superusers defined. Would you like to create one now? (yes/no): yes Username (leave blank to use 'apache'): root E-mail address: [email protected] Password: Password (again): Superuser created successfully. Installing custom SQL ... Installing indexes ... Installed 0 object(s) from 0 fixture(s) bash-4.1$ exit and the local-settings.py file is as follows STORAGE_DIR = '/var/lib/graphite-web' INDEX_FILE = '/var/lib/graphite-web/index' DATABASES = { 'default': { 'NAME': '/var/lib/graphite-web/graphite.db', 'ENGINE': 'django.db.backends.sqlite3', 'USER': '', 'PASSWORD': '', 'HOST': '', 'PORT': '' } } I still get this error [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] File "/usr/lib/python2.6/site-packages/django/db/backends/sqlite3/base.py", line 344, in execute [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] return Database.Cursor.execute(self, query, params) [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] DatabaseError: attempt to write a readonly database not sure what is missing in this configuration

    Read the article

  • WD1000FYPS harddrive is marked 0 mb in 3ware (and no SMART)

    - by osgx
    After reboot my SATA 1TB WD1000FYPS (previously is was "Drive error") is marked 0 mb in 3ware web gui. Complete message: Available Drives (Controller ID 0) Port 1 WDC WD1000FYPS-01ZKB0 0.00 MB NOT SUPPORTED [Remove Drive] SMART gives me only Device Model and ATA protocol version 1 (not 7-8 as it must be for SATA) What does it mean? Just before reboot, when is was marked only with "Device Error", smart was: Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: WD-WCASJ1130*** Firmware Version: 02.01B01 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Mar 7 18:47:35 2010 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 188 186 021 Pre-fail Always - 7591 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 229 5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 3 7 Seek_Error_Rate 0x000e 193 193 000 Old_age Always - 125 9 Power_On_Hours 0x0032 078 078 000 Old_age Always - 16615 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0012 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 77 192 Power-Off_Retract_Count 0x0032 198 198 000 Old_age Always - 1564 193 Load_Cycle_Count 0x0032 146 146 000 Old_age Always - 164824 194 Temperature_Celsius 0x0022 117 100 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 199 199 000 Old_age Always - 1 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 What can be wrong with he? Can it be restored? PS new smart is === START OF INFORMATION SECTION === Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: [No Information Found] Firmware Version: [No Information Found] Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 1 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Mar 8 00:29:44 2010 MSK SMART is only available in ATA Version 3 Revision 3 or greater. We will try to proceed in spite of this. SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported. Checking for SMART support by trying SMART ENABLE command. Command failed, ata.status=(0x00), ata.command=(0x51), ata.flags=(0x01) Error SMART Enable failed: Input/output error SMART ENABLE failed - this establishes that this device lacks SMART functionality. A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. PPS There was a rapid grow of " 192 Power-Off_Retract_Count " before dying. The hard was used in raid, with several hards from the same fabric packaging box (close id's). The hard drives were placed identically. Rapid means almost linear grow from 300 to 1700 in 6-7 hours. Maximal temperature was 41C. (thanks to munin's smart monitoring)

    Read the article

  • Vmware Player 3.0 - cannot ping 32 bits guest from 64 bits (guest or host)

    - by npmj
    I'm stuck with what seems a bug in VmWare Player (build 203739). I'm using W7 Ultimate 64bits as host and have a CentOS 5.4 (64 bits) as a guest and a Windows XP Professional SP3 (32 bits) as another guest. From the 64 bits machines (the host and the linux guest) I cannot ping the windows XP. Off course, I already turned off the windows firewall in the guest and also in the host. The network is pretty basic, I'm using Vmnet8 (NAT), with DHCP and port forwarding (to the windows XP's IP). Everything is working ok, I have internet access from host and from both guests. Port forwarding to the XP guest is working ok too. The only problem is that I cannot access the XP guest through the Vmnet8. I monitored the traffic using wireshark (in the host and in the windows guest). If I try to ping the XP guest from the host, what I see is the ARP request leaving the host, being answered by the guest and, after that, there is no echo request leaving the host. The same occurs if I try to ping the XP from the CentOs guest. From the windows XP guest I can ping both the host and the CentOs guest. From the XP guest I can access the host shares. Obviously, from the host I cannot see the XP shares (as I cannot even ping the guest). I want to maintain this setup (using NAT to share the host's internet connection). Any suggestions?

    Read the article

  • snort with barnyard2 not working on Fedora 12

    - by aHunter
    Has anyone come across this error with barnyard2 and snort? --== Initializing Barnyard2 ==-- Initializing Input Plugins! Initializing Output Plugins! Parsing config file "/etc/snort/barnyard2.conf" Log directory = /var/log/barnyard2 database: compiled support for (mysql) database: configured to use mysql database: schema version = 107 database: host = localhost database: user = test database: database name = snort database: sensor name = localhost:eth0 database: sensor id = 1 database: data encoding = hex database: detail level = full database: ignore_bpf = no database: using the "log" facility --== Initialization Complete ==-- ______ -*> Barnyard2 <*- / ,,_ \ Version 2.1.8 (Build 251) |o" )~| By the SecurixLive.com Team: http://www.securixlive.com/about.php + '''' + (C) Copyright 2008-2010 SecurixLive. Snort by Martin Roesch & The Snort Team: http://www.snort.org/team.html (C) Copyright 1998-2007 Sourcefire Inc., et al. WARNING: Ignoring corrupt/truncated waldofile '/var/log/snort/barnyard.waldo' Opened spool file '/var/log/snort/snort.log.1282004944' ERROR: Unknown record type read: 104 Fatal Error, Quitting.. Snort seems to be working correctly as I have managed to get logs via syslog but when I try to use the barnyard config via Unified2 it is not working. Presumably because of the above error. Thanks in advance.

    Read the article

  • How to verify PostgreSQL 9 has installed correctly on a CentOS server?

    - by A4J
    I'm trying to install the PG (postgres) gem on a CentoOS server, but it keeps saying Postgres is too old, even though I have upgraded it to 9.1.3 (as per the instructions here http://www.davidghedini.com/pg/entry/install_postgresql_9_on_centos). I am using CentOS 5.8 (and Ruby 1.9.3) Here is the error message: Building native extensions. This could take a while... ERROR: Error installing pg: ERROR: Failed to build gem native extension. /usr/local/bin/ruby extconf.rb checking for pg_config... yes Using config values from /usr/bin/pg_config checking for libpq-fe.h... yes checking for libpq/libpq-fs.h... yes checking for pg_config_manual.h... yes checking for PQconnectdb() in -lpq... yes checking for PQconnectionUsedPassword()... no Your PostgreSQL is too old. Either install an older version of this gem or upgrade your database. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. psql --version confirms my version: psql (PostgreSQL) 9.1.3 I can confirm packages installed: Setting up Install Process Package postgresql91-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-devel-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-server-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-libs-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-contrib-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Nothing to do Any ideas on how to troubleshoot this? Thanks in advance.

    Read the article

  • RPM Spec How to specify in package so that previous RPM is removed

    - by user123819
    Question: What do I put in the foo.spec file so that the rpm's will remove the previous rpm before installing? Description: I have created a spec file that creates rpm's for a few packages that use the same source and provide the same service, each with a slightly different configuration. E.g. they each provide the same "capability" Here's an example of the essentials that my .spec file looks like: %define version 1234 %define name foo %define release 1 %define pkgname %{name}-%{version}-%{release} Name: %{name} Version: %{version} Release: %{release} Provides: %{name} %package one Summary: Summary for foo-one Group: %{group} Obsoletes: %{name} <= %{version} Provides: %{name} = %{version} %description one Blah blah blah %package two Summary: Summary for foo-two Group: %{group} Obsoletes: %{name} <= %{version} Provides: %{name} = %{version} %description two Blah blah blah # %prep, %install, %build and %clean are pretty simple # and omitted here for brevity sake %files one %defattr(-,root,root,-) %{_prefix}/%{pkgname} %files two %defattr(-,root,root,-) %{_prefix}/%{pkgname} When I install the first one, it installs ok. I then remove the first one, and then install the second one, that works fine too. I then install the first one, followed immediately by installing the second one, and they both install, one over the other, but, I was expecting that the second one would be removed before installing the second. Example session: # rpmbuild foo and copy rpms to yum repo $ yum install foo-one ... $ yum list installed|grep foo foo-one.noarch 1234-1 @myrepo $ yum install foo-two ...[Should say that it is removing foo-one, but does not]... $ yum list installed|grep foo foo-one.noarch 1234-1 @myrepo foo-two.noarch 1234-1 @myrepo $ rpm -q --provides foo-one foo = 1234 foo-one = 1234-1 $ rpm -q --provides foo-two foo = 1234 foo-two = 1234-1 What do I put in the foo.spec file so that the rpm's will remove the previous rpm before installing? Thank you, .dave.

    Read the article

  • Multiple vlans access to shared pbx system

    - by Matt
    I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

    Read the article

  • Installinf Xen 4.0.1 in Ubuntu 10.10

    - by Hiranth
    make -f buildconfigs/mk.linux-2.6-pvops build make[3]: Entering directory /home/hirantha/xen-4.0.1' set -ex; \ if ! [ -d linux-2.6-pvops.git ]; then \ rm -rf linux-2.6-pvops.git linux-2.6-pvops.git.tmp; \ mkdir linux-2.6-pvops.git.tmp; rmdir linux-2.6-pvops.git.tmp; \ git clone -o xen -n git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-pvops.git.tmp; \ (cd linux-2.6-pvops.git.tmp; git checkout -b xen/stable-2.6.32.x xen/xen/stable-2.6.32.x ); \ mv linux-2.6-pvops.git.tmp linux-2.6-pvops.git; \ fi + '[' -d linux-2.6-pvops.git ']' + rm -rf linux-2.6-pvops.git linux-2.6-pvops.git.tmp + mkdir linux-2.6-pvops.git.tmp + rmdir linux-2.6-pvops.git.tmp + git clone -o xen -n git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git linux-2.6-pvops.git.tmp Initialized empty Git repository in /home/hirantha/xen-4.0.1/linux-2.6-pvops.git.tmp/.git/ fatal: Unable to look up git.kernel.org (port 9418) (Name or service not known) make[3]: *** [linux-2.6-pvops.git/.valid-src] Error 128 make[3]: Leaving directory/home/hirantha/xen-4.0.1' make[2]: * [linux-2.6-pvops-install] Error 2 make[2]: Leaving directory /home/hirantha/xen-4.0.1' make[1]: *** [install-kernels] Error 1 make[1]: Leaving directory/home/hirantha/xen-4.0.1' make: * [world] Error 2 hirantha@hirantha-desktop:~/xen-4.0.1$ ^C hirantha@hirantha-desktop:~/xen-4.0. What is this error? How can i solve this?

    Read the article

  • NGINX SSI Not working

    - by Mike Kelly
    I'm having trouble getting SSI to work on NGINX. You can see the problem if you hit http://www.bakerycamp.com/test.shtml. Here is the contents of that file: <!--# echo hi --> If you hit this in a browser, you see the SSI directive in the content - so apparently NGINX is not interpreting the SSI directive. My NGINX config file looks like this: server { listen 80; server_name bakerycamp.com www.bakerycamp.com; access_log /var/log/nginx/bakerycamp.access.log; index index.html; root /home/bakerycamp.com; location / { ssi on; } # Deny access to all hidden files and folders location ~ /\. { access_log off; log_not_found off; deny all; } } I did not build NGINX from sources but installed it using apt-get. I assume it has the SSI module (since that is default) but perhaps not? Should I just bite the bullet and rebuild from sources? Is there anyway to tell if the installed NGINX supports SSI and my config is just wrong?

    Read the article

  • Netscaler - Involving Response Body Replacement with GeoIP Implementation

    - by MrGoodbyte
    I have a Netscaler (10000) NS9.3: Build 52.3.cl There is a document contains a short tutorial about GeoIP database implementation at http://support.citrix.com/article/CTX130701 I have added location database by following this tutorial successfully but instead of dropping connections I need to replace a string in content body. To do that, I created a rewrite action with those parameters. * Name: ns_country_replacement_action * Type: REPLACE_ALL * Target Expression: HTTP.RES.BODY(50000) * Replacement Text: HTTP.RES.HEADER("international") * Pattern: \{\/\*COUNTRY_NAME\*\/\} To insert header called "international", I try to create another rewrite action with those parameters. I'll add this one's policy prior. * Name: ns_country_injection_action * Type: INSERT_HTTP_HEADER * Header Name: international * Header Value: CLIENT.IP.SRC.MATCHES_LOCATION("*.US.*.*.*.*").NOT When I click on create button, it says; Compound expression syntax error, [.*.*").NOT^, 50] I'm not sure but I think that two things might cause this error. The expression I use for MATCHES_LOCATION is wrong but I use same expression in the tutorial. MATCHES_LOCATION().NOT returns BOOLEAN but the field expects STRING. How can I get this work? Do I use right tools to accomplish what I need to do? Thank you. -Umut

    Read the article

  • Problems building nodejs on MacOS Snow Leopard

    - by mrwooster
    I am having trouble building nodejs on MacOS Snow Leopard. I think it might have something to do with my PATH variable not being set correctly for the developer tools location. For some reason, the Developer tools (gcc, g++, make etc) are all stored in /Developer/usr/bin I added it to my PATH variable as follows: $ export PATH=$PATH:/Developer/usr/bin $ echo $PATH /opt/local/bin:/opt/local/sbin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/local/git/bin:/usr/X11/bin:/Developer/usr/bin When i try to configure it complains about not finding open-ssl, ok, not a big problem. So I try with --without-ssl : $ ./configure --without-ssl Checking for program g++ or c++ : /Developer/usr/bin/g++ Checking for program cpp : /Developer/usr/bin/cpp Checking for program ar : /usr/bin/ar Checking for program ranlib : /Developer/usr/bin/ranlib Checking for g++ : ok Checking for program gcc or cc : /Developer/usr/bin/gcc Checking for gcc : ok Checking for library dl : yes Checking for library util : yes Checking for library rt : not found --- libeio --- Checking for library pthread : yes Checking for function pthread_create : not found /Users/Guy/git_src/node/node/deps/libeio/wscript:13: error: the configuration failed (see '/Users/Guy/git_src/node/node/build/config.log') Anyone know how I can get round this? I am suspicious that it might be something to do with the PATH or another ENV variable, but not sure. Thanks G

    Read the article

  • Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

    - by Shalan
    Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

    Read the article

  • Looking for updated BIOS for '99 Gateway in order to format/recognize >127 GB HD

    - by Jeff
    I have a '99 Gateway that's apparently too old for even Gateway to acknowledge it exists. Want to use it as a media hub and put in a 320GB HD, but it will not format above 127GB even running Win XP SP3. Read somewhere that upgrading the BIOS may do the trick, but I can't find the correct BIOS, and GW has been no help. Hoping I can just upgrade the BIOS, which is 11 years old. Any help would be much appreciated! I don't know where to look, and searches have been fruitless. System info: OS Name Microsoft Windows XP Home Edition Version 5.1.2600 Service Pack 3 Build 2600 OS Manufacturer Microsoft Corporation System Name xxxx System Manufacturer Gateway System Model TABOR_II System Type X86-based PC Processor x86 Family 6 Model 7 Stepping 3 GenuineIntel ~596 Mhz BIOS Version/Date Intel Corp. 4W4SB0X0.15A.0015.P10, 9/28/1999 SMBIOS Version 2.1 BIOS info (from a free app I located): BIOS Type: Phoenix BIOS Date: September 28th 1999 BIOS ID: 4W4SB0X0.15A.0015.P10.9909281445-None BIOS OEM: 4W4SB0X0.15A.0015.P10 Chipset: Intel 440BX/ZX rev 3 SuperIO: SMC 70x or 80x rev 0 at port 0370 Manufacturer: Gateway Motherboard: WS440BX

    Read the article

  • Vmware Player 3.0 - cannot ping 32 bits guest from 64 bits (guest or host)

    - by npmj
    I'm stuck with what seems a bug in VmWare Player (build 203739). I'm using W7 Ultimate 64bits as host and have a CentOS 5.4 (64 bits) as a guest and a Windows XP Professional SP3 (32 bits) as another guest. From the 64 bits machines (the host and the linux guest) I cannot ping the windows XP. Off course, I already turned off the windows firewall in the guest and also in the host. The network is pretty basic, I'm using Vmnet8 (NAT), with DHCP and port forwarding (to the windows XP's IP). Everything is working ok, I have internet access from host and from both guests. Port forwarding to the XP guest is working ok too. The only problem is that I cannot access the XP guest through the Vmnet8. I monitored the traffic using wireshark (in the host and in the windows guest). If I try to ping the XP guest from the host, what I see is the ARP request leaving the host, being answered by the guest and, after that, there is no echo request leaving the host. The same occurs if I try to ping the XP from the CentOs guest. From the windows XP guest I can ping both the host and the CentOs guest. From the XP guest I can access the host shares. Obviously, from the host I cannot see the XP shares (as I cannot even ping the guest). I want to maintain this setup (using NAT to share the host's internet connection). Any suggestions?

    Read the article

  • Windows Update Agent Update Failed

    - by Adrian Godong
    I'm trying to install the latest version of Windows Update Agent, v7.2.6001.788, and the installation failed with error code of 0x800b0100. Running Windows Server 2008 SP1. The relevant WindowsUpdate.log section: 2009-08-03 16:17:49:334 3544 d28 Misc =========== Logging initialized (build: 7.2.6001.788, tz: +0100) =========== 2009-08-03 16:17:49:334 3544 d28 Misc = Process: d:\fcc0f96e893296900e6501a601\wusetup.exe 2009-08-03 16:17:49:332 3544 d28 Setup Windows Update Client standalone setup : resource dll path is d:\fcc0f96e893296900e6501a601\en\wusetup.exe.mui 2009-08-03 16:17:49:335 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:49:556 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:556 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-ActiveX.cab" 2009-08-03 16:17:49:580 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:580 3544 d28 Setup Evaluating CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Aux-TopLevel.cab" 2009-08-03 16:17:49:665 3544 d28 Setup Package will be installed 2009-08-03 16:17:49:709 3544 d28 Setup Windows Update Client standalone setup : eula file path is d:\fcc0f96e893296900e6501a601\en\eula.rtf 2009-08-03 16:17:52:337 3544 de0 Misc WARNING: LoadLibrary failed for srclient.dll with hr:8007007E 2009-08-03 16:17:52:338 3544 de0 Setup Installing CBS package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" 2009-08-03 16:17:53:895 3544 de0 Setup WARNING: CBS operation failed, error = 0x800B0100 2009-08-03 16:17:53:898 3544 de0 Setup WARNING: Install of setup package "d:\fcc0f96e893296900e6501a601\WUClient-SelfUpdate-Core-TopLevel.cab" failed, error = 0x800B0100 2009-08-03 16:18:04:976 3544 d28 Setup wusetup has finished. Exit code is 0. Reboot is NOT needed I think something went wrong twhen loading the srclient.dll. Things that I have done and still no fix: msiexec /unregister and msiexec /register regsvr32 wuapi.dll Run CheckSUR tool and restart

    Read the article

  • How to give a user NTFS rights to a folder, via Powershell

    - by Don
    I'm trying to build a script that will create a folder for a new user on our file server. Then take the inherited rights away from that folder and add specific rights back in. I have it successfully adding the folder (if i give it a static entry in the script), giving domain admin rights, removing inheritance, etc...but i'm having trouble getting it to use a variable I set as the user. I don't want there to be a static user each time, I want to be able to run this script, have it ask me for a username, it then goes out and creates the folder, then gives that same user full rights to that folder based on the username i've supplied it. I can use Smithd as a user, like this: New-Item \\fileserver\home$\Smithd –Type Directory But can't get it to reference the user like this: New-Item \\fileserver\home$\$username –Type Directory Here's what i have: Creating a new folder and setting NTFS permissions. $username = read-host -prompt "Enter User Name" New-Item \\\fileserver\home$\$username –Type Directory Get-Acl \\\fileserver\home$\$username $acl = Get-Acl \\\fileserver\home$\$username $acl.SetAccessRuleProtection($True, $False) $rule = New-Object System.Security.AccessControl.FileSystemAccessRule("Administrators","FullControl", "ContainerInherit, ObjectInherit", "None", "Allow") $acl.AddAccessRule($rule) $rule = New-Object System.Security.AccessControl.FileSystemAccessRule("Domain\Domain Admins","FullControl", "ContainerInherit, ObjectInherit", "None", "Allow") $acl.AddAccessRule($rule) $rule = New-Object System.Security.AccessControl.FileSystemAccessRule("Domain\"+$username,"FullControl", "ContainerInherit, ObjectInherit", "None", "Allow") $acl.AddAccessRule($rule) Set-Acl \\\fileserver\home$\$username $acl I've tried several ways to get it to work, but no luck. Any ideas or suggestions would be welcome, thanks.

    Read the article

  • RTL8192SU Linux Issue Installing Driver

    - by s32ialx
    OK I've read tons of fourms of people getting the onboard RTL8192SE working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

    Read the article

  • r1soft agent is failing with the error: "write error while sending code: Broken pipe"

    - by curiousguy
    I have an Ubuntu 10.04.4 LTS server with r1soft agent installed in it. Recently, the backups are failing with the following error. -------- write error while sending code: Broken pipe -------- I have reinstalled the buagent but to no avail. On checking the server logs, I could see the following errors listed in it: -------- # tail -f /var/log/messages |grep -i buagent Nov 17 03:35:06 microscope buagent: Need to back up 126 sectors Nov 17 03:35:06 microscope buagent: (Righteous Backup Linux Agent) 1.79.0 build 12433 Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.195) with valid RSA key Nov 17 03:35:06 microscope buagent: allowing control from backup server (10.128.136.201) with valid RSA key Nov 17 03:35:06 microscope buagent: sending auth challenge for allowed host at (10.128.136.201) port (47890) Nov 17 03:35:06 microscope buagent: host (10.128.136.201) port (47890) authentication successful Nov 17 03:35:06 microscope buagent: Backup request accepted. Starting backup. Nov 17 03:35:06 microscope buagent: Snapshot completed in 0.010 seconds. Nov 17 03:45:03 microscope buagent: Error reading blocks from snapshot. Nov 17 03:45:03 microscope buagent: Reading blocks failed Nov 17 03:45:03 microscope buagent: error backup aborted Nov 17 03:45:03 microscope buagent: backup failed on agent closing connection Nov 17 03:45:03 microscope buagent: Backup failed. Nov 17 03:45:03 microscope buagent: write error while sending code: Broken pipe (32) Nov 17 03:45:03 microscope buagent: tell child write failed -------- I tried changing the 'Timeout' and 'DiskAsPartition' value in '/etc/buagent/agent_config' file but no luck. Also, verified that proper route is added to the backup server. The agent is also running fine. Am I missing anything? Any help would be much appreciated. Note: CDP 2.0 is installed in the backup server.

    Read the article

  • Menu tab completion for recent history in zsh

    - by dat5h
    I am interested in a potential zle widget for zsh. Is there a way to build a widget that mimics the kill-completion selectable menu? Essentially I want to be able to press , tab in vi-command-mode, or maybe !-tab-completion at the shell and get a list of recent history (or related history compared what is already entered at the commandline) that allows me to scroll through it and possibly select a relevant function to call or compare similar calls. Looking through the manual I stumbled onto a similar widget that I have mapped like so: # tab completion history menu (vicmd) autoload -z history-beginning-search-menu zle -N history-beginning-search-menu-space-end history-beginning-search-menu bindkey -M vicmd "\t" history-beginning-search-menu-space-end # emacs binding could be "\e\t"? (I wouldn't know) Therefore, if I enter vicmd and hit tab when I enter something like "grep", then I get a list of all grep calls in history. It also asks me for the list-number and it will perform the numbered item in history. If I enter a space and then try this, it lists ALL of my history history. This is fairly close to what I want, but there are some problems. For example, 1) it prints the entire list of relevant history and does not check the number of lines of the screen so it could easily blow up the space on the terminal; 2) when I type in numbers for selecting an item in history it does not show me the numbers I type, so I may make a mistake and have to start over again; 3) I would love to be able to hook in appearance tweaks. I was wondering if there exists more updated version of this widget or if there is any way to look at the source for kill-completion or history-beginning-search-menu to see if I could think of a way to do it.

    Read the article

< Previous Page | 875 876 877 878 879 880 881 882 883 884 885 886  | Next Page >