Search Results

Search found 29317 results on 1173 pages for 'device control'.

Page 883/1173 | < Previous Page | 879 880 881 882 883 884 885 886 887 888 889 890  | Next Page >

• How do I connect to and factory reset a Catalyst 3560 Switch?

  - by Josh

  My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

  Read the article

• How to connect android client to the localhost of Apache server (php) inside my laptop?

  - by user1796310

  I'm trying to create android apps which able sending data through wifi connection to my laptop Apache Server and MySQL database. I use the samsung galaxy tab 10.1 as my mobile device. and the protocol i used is HttpGet or HttpPost. And i use XAMPP( with Apache& SQL) to do the server and process the php. But, due to android cannot detect adhoc network from laptop, i use Virtual Router ( for window 7) to create virtual access point and make the tablet able connect to my laptop. But the problem is: [1] in my apps (client-android), where the httpget or httppost to which url? localhost in my laptop- 127.0.0.1 or localhost in android 10.0.0.1? or the ip address of the virtual router? [2]so, if i want access from android to the localhost(laptop-Apache) to call the php to run? which port? which ip address /url that i need to put in android apps(httpget)? and do i need to modify anything in httpconfig for XAMPP? thanks alot.

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Tried to install Mint to a Flash Drive. Now I can't boot from the main hard disk.

  - by Dan

  Hello, all. I'm kind of new to Linux and I need some help. I wanted to install a Linux distro to a flash drive so that I can have a portable OS with all my settings, programs, etc. wherever I go. So I fired up a Linux Mint Live CD and installed Mint to the flash drive, and this seems to work OK. But now, whenever I try to boot up my system normally without the flash drive plugged in, it doesn't seem to work. It basically hangs for a bit, and then I get the following prompt: error: no such device: (some long hex val) grub rescue> However, when I try powering my system up when the USB is plugged into the computer, it gives me an option between using the OS installed on my USB and the OS installed on my HD. Selecting the latter, everything loads up just fine. I'm guessing that installing Mint to the flash drive somehow messed with my native Grub installation, but, again, I'm kind of new to Linux, so I'm not sure exactly why. Any help is greatly appreciated.

  Read the article

• Route outbound connections from local network through VPN

  - by Sharkos

  I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

  Read the article

• Corsair SSD appears completely blank and does not retain written data

  - by ebanders

  I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

  Read the article

• ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

  - by chickenloop

  I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

  Read the article

• Using GPO to collect data about VMware view activity

  - by MoSiAc

  Our security group wants us to begin logging data for external access to our view enviroment. At first we thought that view security would be logging all source ip's that are external in nature so if for some reason there is an intrusion we would have record of it there. Of course our firewall logs all that information but correlating it to view is sketchy at best with our current implementation. We know on viewdesktops there is a set of keys in VolitateEnviroment that contains stuff such as source ip and username, etc. We have a script in place that, when run as a logon script attached to a user account in AD collects the information as we need it. If we have a GPO run the same script the information does not get collected. We feel like there is a piece of the puzzle we're missing but we don't know what. If anyone knows what we're forgetting or misconfiguring that would be great, or if you have a better way of us collecting external source ip's for view specifically we'd be interested in that as well. Thanks, EDIT CODE Batch script to dump to text file @echo off timeout 20 echo %computername%/%username% %time% %date% c:\vdi\vmware.txt echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_LoggedOn_Username"c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_IP_Address"c:\vdi\vmware.txt echo.c:\vdi\vmware.txt VB Script to display values Const HKEY_CURRENT_USER = &H80000001 Set wmiLocator=CreateObject("WbemScripting.SWbemLocator") Set wmiNameSpace = wmiLocator.ConnectServer(".", "root\default") Set objRegistry = wmiNameSpace.Get("StdRegProv") sPath = "Volatile Environment" lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_Machine_Name", vMachine) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_IP_Address", vIP) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_MAC_Address", vMAC) msgbox "The Remote Device Name is " & vMachine & " @ " & vIP & " (" & vMAC & ") " he wanted me to mention that the batch file actually runs and I can see it counting down when I reconnect but it does not grab the registry values.

  Read the article

• Force Installing a Radeon HD 2100 on Windows 8

  - by Click Ok

  I'm trying force installing a Radeon HD 2100 on Windows 8. I've found that link from AMD with the drivers for Windows7: http://support.amd.com/us/gpudownload/windows/legacy/Pages/legacy-radeonaiw-vista64.aspx I know too that AMD will stop support Radeon HD 400 and older: http://www.techspot.com/news/48321-amd-drops-windows-8-support-for-radeon-hd-4000-and-older.html Now, let's go to the problem. If I try install the 12.6 driver, Windows will stick with the "basic display adapter", and this is bad for 3d games like Minecraft, that runs really slow now compared with the previous Windows7 installation. Forcing install the catalyst driver can help to fix it. So, I follow that steps: Extract the Catalist Driver (C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql) Right click the "basic display adapter" on device manager, and "update driver" Search on PC I will choose the driver "With Disk" "C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql\Packages\Drivers\Display\W76A_INF" There is a big list of drivers and the nearest driver to HD 2100 is "Radeon HD 2350 Series" My questions: Why isn't "Radeon HD 2100 Series" listed? (or Where is it listed?) In theory it must be listed" The first link above show that "This article applies to the following configuration(s):" (...) "AMD Radeon HD 2000 Series" Am I doing something wrong?

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  Hi, I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

• Kindle (client) for Mac--text search or highlighting/notes?

  - by doug

  just so we're clear, i'm talking about the client/software version here--ie, that you install on your Mac or PC--not the device. The Kindle client was recently released for the Mac. I downloaded it and bought a couple of Kindle-edition books to view on this client. Astonishingly, two features i consider to be more or less essential to any ebook reader are missing in the Kindle client, either that, or i can't find them: (i) text searching; and (ii) highlighting text. First, does anyone know how to access the search feature? I'm aware of the "Go To" button at the top middle of the reader window--the options in that menu when you click the button are: "Cover", "Table of Contents", "Beginning" and "Location." "Location" requires that you type in an integer (but it doesn't correspond to page number--e.g., typing "167" brought me to the table of contents), not a search term. Second, there's a button on the upper right-hand corner of the window "Show Notes and Marks" yet i can't find any way to highlight text. The only kind of "note" or "mark" i have been able to record is to "bookmark" a page by clicking the "bookmark" button also at the top of the window.

  Read the article

• Google Chrome on Linux not using ALSA for sound

  - by DarkMoon

  On my laptop, I've got an .asoundrc file that outputs sound to my USB headset. This works fine for SMplayer and Firefox. However, Google Chrome (at least, Flash-based and HTML5-based videos and HTML5-based audio in Chrome) plays through the laptop speakers instead. I've tried running Chrome from a command-line, hoping there would be some helpful output, but no such luck. I've tried looking through Google for whether Chrome even uses ALSA, or if it uses something else, but I have been unsuccessful in this. This question seems to be the same issue, but no suggestion was made. Anyone have any ideas? I'm running Gentoo with a 3.10.17 kernel, 1.0.27 ALSA utils, 2.6.5 FVWM, and 36.0.1985.143 Chrome. If you need more info, please let me know. EDIT: I've configured the USB headset as the default ALSA device. Volume levels for both headset and onboard are set and un-muted using alsamixer. My .asoundrc file is as follows. ctl.!default { type hw card Headset } pcm.dmixer { type dmix ipc_key 1024 slave { pcm { type hw card Headset } period_size 1024 buffer_size 4096 } bindings { 0 0 1 1 } } pcm.!default { type plug slave.pcm dmixer }

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• How to fix missing RAID1 drive

  - by Sodved

  I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• Ubuntu's garbage collection cron job for PHP sessions takes 25 minutes to run, why?

  - by Lamah

  Ubuntu has a cron job set up which looks for and deletes old PHP sessions: # Look for and purge old sessions every 30 minutes 09,39 * * * * root [ -x /usr/lib/php5/maxlifetime ] \ && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 \ -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir \ fuser -s {} 2> /dev/null \; -delete My problem is that this process is taking a very long time to run, with lots of disk IO. Here's my CPU usage graph: The cleanup running is represented by the teal spikes. At the beginning of the period, PHP's cleanup jobs were scheduled at the default 09 and 39 minutes times. At 15:00 I removed the 39 minute time from cron, so a cleanup job twice the size runs half as often (you can see the peaks get twice as wide and half as frequent). Here are the corresponding graphs for IO time: And disk operations: At the peak where there were about 14,000 sessions active, the cleanup can be seen to run for a full 25 minutes, apparently using 100% of one core of the CPU and what seems to be 100% of the disk IO for the entire period. Why is it so resource intensive? An ls of the session directory /var/lib/php5 takes just a fraction of a second. So why does it take a full 25 minutes to trim old sessions? Is there anything I can do to speed this up? The filesystem for this device is currently ext4, running on Ubuntu Precise 12.04 64-bit. EDIT: I suspect that the load is due to the unusual process "fuser" (since I expect a simple rm to be a damn sight faster than the performance I'm seeing). I'm going to remove the use of fuser and see what happens.

  Read the article

• Role of MBR in the booting process

  - by pg4421

  I am new to stack overflow. So please correct me if my question seems irrelevant or stupid. I read here in Booting Process : The job of the primary boot loader is to find and load the secondary boot loader (stage 2). It does this by looking through the partition table for an active partition. When it finds an active partition, it scans the remaining partitions in the table to ensure that they're all inactive. When this is verified, the active partition's boot record is read from the device into RAM and executed. The question is that I am having a Hard disk which has two Operating System images windows and ubuntu and hence both partitions in which they reside are active. Then why do we have only one active partition always? (I know that active partition is one of the primary partition but then why we are giving special reference to one primary partition? ) I am confused a bit. Please solve my query. Thank you so much.

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine? [closed]

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Why is /dev/urandom only readable by root since Ubuntu 12.04 and how can I "fix" it?

  - by Joe Hopfgartner

  I used to work with Ubuntu 10.04 templates on a lot of servers. Since changing to 12.04 I have problems that I've now isolated. The /dev/urandom device is only accessible to root. This caused SSL engines, at least in PHP, for example file_get_contents(https://... to fail. It also broke redmine. After a chmod 644 it works fine, but that doesnt stay upon reboot. So my question. why is this? I see no security risk because... i mean.. wanna steal some random data? How can I "fix" it? The servers are isolated and used by only one application, thats why I use openvz. I think about something like a runlevel script or so... but how do I do it efficiently? Maby with dpkg or apt? The same goes vor /dev/shm. in this case i totally understand why its not accessible, but I assume I can "fix" it the same way to fix /dev/urandom

  Read the article

• How to set up multiple video cards in Windows XP

  - by Swish

  All I am trying to do is run a three monitor setup, two widescreens on the good card at high res and a third smaller monitor at 1024x768 that I watch continuously updating info in. I have a Dell Vostro 200 with an HIS Radeon HD 4670 video card in the PCI-e slot. I need an additional video card that will work in an available PCI slot. I Had a Nvidia GeForce 5200 that was installed but due to what I'm assuming was a compatible driver issue (because it was Nvidia not ATI) it wouldn't run at more than 640x480 4bit color when installed simultaneously with the HIS card. Previously I used the Nvidia with the onboard Intel video to run a third monitor, but now that the HSI uses PCI-e the onboard has to be disabled. I tried a Radeon 9200 PCI card that I found (microsoft made I think) with it and only that or the HIS card could be enabled at the same time. When both were in the HIS card said "The device cannot start". SO, based on the fact that I got the Nvidia to work (although very poorly) with the new HIS Radeon HD 4670 PCI-e I know it's possible, just don't know what type of card I need to use. Any ideas?

  Read the article

• Is this DVD drive broken? Brand new, i need help convincing

  - by acidzombie24

  I am asking bc i know dell is going to give me a problem. How do i know if my DVD is broken on my laptop? i burnt 4 DL disc and they ALL failed, i called and dell suggested roxio. I used it and burnt 1 disc without error and the 2nd disc with an error. With both apps there were no 'problems' during the burning process only failed on the verification process. Some of these bad disc dont work on other PCs and one locks up windows when i click a specific file. Does that sound like a broken burner to you guys? when i called dell they told me since it can read disc properly 100% of the time and software doesnt fail in the burning process its not a broken drive _. They forward me to software support who demand a fee (i think $100) to help me fix my software. I am annoyed bc i dont want to be on the phone for them to watch me burn a dvd and since i burned it once correctly i dont want to happen to burn correctly again to have them say they solved my problem (doing nothing) and charge me refusing to refund. -edit- The errors i got were 1) the request could not be performed because of an I/O device error 2) Windows locking up when opening 1 specific file 3) Cannot copy : Data error (crc) NOTE: the file that causes the problems are random every disc

  Read the article

• [SOLVED} How do I restore my audio after uninstalling Ventrilo?

  - by Marcx

  Hi, I've a Dell studio 1555 bought on september with Windows 7 64bit Professional on it. The audio device works proprerly, while listening to audio contents (from disk or internet) When I use Ventrilo, the audio from other people sounds good and I hear their voices clearly When I use any other VOIP programs like Teamspeak 3, MSN or Skype, I hear a disturbed voice, and it's impossible to comprehend something... Anyway everything worked fine until I installed Ventrilo, but removing it didn´t solve my problem. Update: Here's a sample of how I hear others people voices.. Audio Sample After some tests, also the desktop has the same problem. (I tried TeamSpeak3) Here are some details on my laptop and desktop Laptop Dell Studio 1555 Core 2 Duo P8600 2.4Ghz 4Gb Ram Dual Channel Ati HD 4570 512Mb dedicated (up to 2048) IDT High Definition Audio Desktop Motherboard Asus P5KPL-AM Dual Core CPU E5200 2.50Ghz 2x2GB PC6400 Dual Channel Ati Radeon HD 4650 512MB VIA High Definition Audio Both computers have Windows 7 Professional 64Bit. So how do I restore my audio? SOLVED The problem was in router firmware, there was a bug that recognized VoIP traffic as a DOS attack and the router grambled every packet... I've installed the newest firmware and everything is fine :)

  Read the article

• SSD won't boot anymore

  - by LordrAider

  Yesterday I put the computer to sleep. Something went wrong because it didn't go fully to sleep. So I restarted the pc and now it won't boot windows 7 anymore. It said : "Please insert valid boot device". I ran Windows 7 restore disc and tried restoring, first it said, mbr fixed. No result but now it said : "Operating system could not be loaded" I ran Windows 7 restore disc again and then it said something about a corrupt partition and that he fixed it. But got the same msg at restart about operating system not found. I ran Windows 7 restore disc again and used diskpart and watched the volumes. My SSD shows up as RAW filesystem... not as NTFS. The size of the disk seems correct. In the bios it also shows up as Healthy disk. What could went wrong and could I recover data with testdisk? I assume something went wrong with the partition :(. It's a Plextor SSD 256M2P SSD, only 3 months old. Thx in advance

  Read the article

• File upload folder permission fastCGI - How to make it writeable?

  - by user6595

  I am using centos 5.7 with cPanel WHM running fastcgi/suEXEC I am trying to make a particular folder writable to allow a script to upload files but seem to be having problems. The folder (and all recursive folders) I want to be writable is: /home/mydomain/public_html/uploads And I want only scripts run by the user "songbanc" to be able to write to this directory. I have tried the following: chown -R songbanc /home/mydomain/public_html/uploads chmod -R 755 /home/mydomain/public_html/uploads But it still doesn't seem to work. The script will only upload files if I set the permissions manually via FTP client to 777. I assume I am misunderstanding how to set permission for users with fastcgi and hopefully someone can help me. Thanks in advance EDIT: Running getfacl on one of the scripts or folders gives the following: # file: home/mydomain/public_html/ripples/1.jpg # owner: songbanc # group: songbanc So it appears that the owner is correct? I'm now totally confused! EDIT 2: The plot thickens... lsattr and chattr are returning Inappropriate ioctl for device While reading flags on...

  Read the article

< Previous Page | 879 880 881 882 883 884 885 886 887 888 889 890  | Next Page >