Search Results

Search found 29317 results on 1173 pages for 'device control'.

Page 881/1173 | < Previous Page | 877 878 879 880 881 882 883 884 885 886 887 888  | Next Page >

• bond0:0 + define virtual IP

  - by yael

  in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• How to fix Truecrypt MBR using Command Prompt or Linux live USB?

  - by Michal Stefanow

  I was playing with TrueCrypt and decided to make a fresh installation of Windows 7 from USB stick. Unfortunately Windows 7 installer: "setup was unable to create a new system partition" My entire HDD has been formatted and is visible as 320GB unallocated space, but no fdisk nor Windows 7 installer nor Windows XP installer could help. (Windows XP doesn't even see the HDD, it sees only USB stick and says "not enough space to install") It may be related to Truecrypt and pre-boot authentification, boot loader and/or MBR. As I don't have optical device I could not have created rescue disk. Right now I need a rescue of some kind, supposingly by erasing/fixing MBR using Linux live USB or using Command Promt. Another approach is to click "repair your comuter" menu from Windows 7 installer then click "restore your computer", then click OK upon error and get access to Command Prompt. Yet another another approach is to start computer without Linux USB I receive this: error:unknown filesystem. grub rescue> Any help would be greatly appreciated as my laptop is kind of not fully operational now. UPDATE: This was asked long time ago, ended up formatting everything (eventually it worked using different bootable USB)...

  Read the article

• Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

  - by teenup

  Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Why is MySQL unable to open hosts.allow/hosts.deny?

  - by HonoredMule

  I have a storage server running Nexenta (OpenSolaris kernel, Ubuntu userspace) with MySQL on top of a ZFS storage array, using innodb_file_per_table and ulimit -n set to 8K. mysqltuner.pl confirms the file limit and claims there are 169 files. The following command: pfiles `fuser -c / 2>/dev/null indicates one mysqld process having 485 file/device descriptors (and they're almost all for files) so I don't know how reliable the tuning script is, but it is still way less than 8K and this list also finds no other process which is close to it's limit. The global total number of descriptors in use is around 1K. So what can cause mysqld to be constantly streaming the following errors? [date] [host] mysqld[pid]: warning: cannot open /etc/hosts.allow: Too many open files [date] [host] mysqld[pid]: warning: cannot open /etc/hosts.deny: Too many open files Everything appears to actually be operating fine, but the issue is constantly flooding the admin console and starts right away on a fresh boot (not only reproducible, but always from mysqld and always the hosts files, whose permissions are the default -rw-r--r-- 1 root root). I could, of course, suppress it from the admin console but I'd rather get to the bottom of it and still allow mysqld warnings/errors to reach the admin console. EDIT: not only is the actual file descriptor well within sane limits, the issue also persists (with immediate appearance) even with the file limit raised to 65535 and always only on hosts.allow/deny.

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• Why is this iptables rule that does port forwarding not working?

  - by videoguy

  I have a server bound to localhost:7060. It is using ipv6 socket instead of ipv4. Below is netstat outout. # netstat -an Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 10.200.32.98:1720 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4122 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4123 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:4123 127.0.0.1:43051 ESTABLISHED tcp 0 0 10.200.32.98:5555 10.200.32.44:53162 ESTABLISHED tcp6 0 0 :::5060 :::* LISTEN tcp6 0 0 ::ffff:127.0.0.1:7060 :::* LISTEN tcp6 0 0 :::23 :::* LISTEN tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.142:43505 ESTABLISHED tcp6 0 0 ::ffff:127.0.0.1:43051 ::ffff:127.0.0.1:4123 ESTABLISHED tcp6 0 0 ::ffff:10.200.32.98:23 ::ffff:10.200.32.44:53195 ESTABLISHED udp6 0 0 :::5060 :::* CLOSE # I want to setup a port forwarding rule that accepts connections on port 24 (on all interfaces loopback as well as eth0) and forward the data to localhost:7060. This is how I am setting up the iptables rule: iptables -t nat -A PREROUTING -p tcp --dport 24 -j DNAT --to 127.0.0.1:7060** It is not working. When I telnet from different box, I see the following $telnet 10.200.32.98 24 Trying 10.200.32.98... If I change the server to bind to *:7060 and set the following rule, it seems to work fine. iptables -t nat -A PREROUTING -p tcp --dport 24 -j REDIRECT --to-port 7060 But that will make my server available on WAN interface which I don't like. I feel it had something to do with ipv6 socket (tcp6 line in netstat output). This whole thing is done on an Android device with custom built Android platform image. How do I get this working?

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• SSH from ubuntu server to Windows 2008 repeatedly asks for password

  - by jrizos

  I am trying to setup GIT using SSH mode. The central GIT repository is on a NAS device running Windows 2008 server and the user GIT repository is on ubuntu 12.04. When I try to SSH to the windows machine however I am not able to successfully get in. SSH keays are not setup but I think the problem is even before that since I cant get in just by providing the correct password. The output from the SSH command is below. Any help would be appreciated. dba@clpserv01:~$ ssh -v -l administrator clpnas OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to clpnas [***.***.***.***] port 22. debug1: Connection established. debug1: identity file /home/dba/.ssh/id_rsa type -1 debug1: identity file /home/dba/.ssh/id_rsa-cert type -1 debug1: identity file /home/dba/.ssh/id_dsa type -1 debug1: identity file /home/dba/.ssh/id_dsa-cert type -1 debug1: identity file /home/dba/.ssh/id_ecdsa type -1 debug1: identity file /home/dba/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze2 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA bd:37:d1:98:51:2a:d6:b5:f5:c7:98:d8:74:2c:4e:cd debug1: Host 'clpnas' is known and matches the RSA host key. debug1: Found key in /home/dba/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /home/dba/.ssh/id_rsa debug1: Trying private key: /home/dba/.ssh/id_dsa debug1: Trying private key: /home/dba/.ssh/id_ecdsa debug1: Next authentication method: keyboard-interactive Password: debug1: Authentications that can continue: publickey,password,keyboard-interactive Password:

  Read the article

• Size of modules within initrd

  - by LiKao

  I am currently trying to manually replace the kernel within ubuntu-core on an embedded device with a custom kernel. However when I try to update the initrd my initrd becomes much bigger. Here is what I did: Extract the initrd that was shipped with ubuntu Make a list of all modules within the old initrd get the same modules from the new module director at /lib/modules/new_kernel_version add these modules to the initrd and remove the old ones If I do this my initrd becomes quite bigger than the original one, so I checked the individual modules. I picked the btrfs.ko filesystem driver as an example. So by comparing these two modules I noticed the one I just picked into the initrd was much bigger, which caused the difference in size. -rw-r--r-- 1 root root 999K Nov 14 15:06 btrfs.ko For the btrfs.ko within the shipped initrd. -rw-r--r-- 1 root root 7.2M Nov 14 15:08 btrfs.ko For the new btrfs.ko. What is different between these two modules? Could this be caused by some faulty setting for the new kernel? When producing the kernel I copied /proc/config.gz and used make oldconfig to update it, so all optimisations should be the same for both kernels. Or is there something else which is being done to the modules before they are put into the initrd? Maybe is there even some better way to build a new initrd for the new kernel in ubuntu altogether. Update: I just also tested with an initrd which I created from scratch using the mkinitrfs command within ubuntu, and it has the same size difference that I found for the initrd I manually updated.

  Read the article

• Website hosted on my virtualbox web server not displaying images or applying css when viewed through phone

  - by WebweaverD

  I would really appreciate it if someone could help me. Please let me know if you need more info in the comments. My Set Up I have a windows 7 pc. On it I run a virtual box VM with a ubuntu 12 guest os and LAMP setup. I share files between the two machines using samba from linux to windows and using windows file sharing (Workgroup) the other way round. The vm is set up with a bridged network adapter and can happily serve web pages to my host machine. I use DHCP reservations on my home wireless router/modem to reserve an ip for the vm and give it a sitename.dev in my windows host file so I can access it at sitename.dev through the browser. The Problem So far so good but I have a dev project which needs a lot of mobile template development, now obviously I can use a browser plugin to simulate a mobile device but I would like to be able to see the real thing easily on my phone during development. So ideally I would like a similar setup on my iphone to my windows setup Now I'm not great on networking and dont have much experience with web server set up. So when I typed the ip of my virtual box into my iphone i wasnt expecting to see anything. I was pleasantly surprised when my site loaded up. The javascript even seems to be running but the images and css are not happening. My Question 1) What is happening here, is it something to do with the bridged set up on the vm network? 2)How do I make the sites load properly through my phone Notes I've also tried another phone. The same sites viewed on live servers work fine.

  Read the article

• wireless to wired internet

  - by Mark T

  My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

  Read the article

• Windows Home Server 2011, No disks "suitable for a backup destination"

  - by Scott Beeson

  I recently installed Windows Home Server 2011 and love it. However, when I try to set up server backups, it says no suitable disks are available. Initially, before I set up my RAID, it found one of my twin drives and said it would work. Once I set up the mirroring, that one is no longer available (obviously). However, I have an internal SATA 1TB drive and an external USB2.0 1TB drive hooked up. Both are recognized by Disk Management. WHS11 still says nothing suitable for backups. The two drives details are as follows: Edit to clarify: The system partition is on Disk 0, not listed below. The two below are the two that SHOULD be available for system backups. Disk 1: Dynamic "Data" (D:) 931.51 GB NTFS, Healthy Disk 3: Basic 200 MB Healthy (EFI System Partition) "Backup" 930.66 GB NTFS, Healthy (Primary Partition) What's a bit odd is that in Disk Management the "Backup" volume does not show a drive letter, even though I assigned Z: (which is reflected in "My Computer". I also cannot make this a dynamic disk as it says it's unsupported by the device.

  Read the article

• Cisco Call Manager adding 7945's

  - by Will

  Hello we currently have a call manager settup (older we are working on upgrading it) but for now we are looking to add 7945 IP phones. We currently have 7960's all over the place, but we can't get these new anymore. Here is the info about our call manager ace.dll 5.2.5.0 CCM4.1(3) aced.dll CCM4.1(3) AdministrativeReportingTool.exe 4.1(0.45) 4.1(3)sr4d Apache Tomcat 4.1 CCM4.1(3) ASTIsapi.dll 3.3.2.0 4.1(3)sr4d AudioTranslator.exe 4.0.0.3 CCM4.1(3) Aupair.exe 4.1.3.10472 4.1(3)sr4d AupairChangeNotify.dll 4.1.0.11 CCM4.1(3) AuthFilt.dll 4.0.0.0 4.1(3)sr4d AVVIDCustomerDirectoryConfigurationPlugin.exe 4.1.0.17(0) CCM4.1(3) bootp.exe 2.0.2.2 CCM4.1(3) BulkAdministrationTool.exe 5.1(4c) 4.1(3)sr4d CallBackService.exe 3.3.2.3 4.1(3)sr4d ccm.exe 4.1.3.17472 4.1(3)sr4d CcmPerfMon.dll 4.1(3)sr4d CCNTEST.EXE CCM4.1(3) cdpintf.dll 4.0.0.0 CCM4.1(3) Cisco CallManager 4.1(3)sr4d 4.1(3)sr4d One of the admins recommenced downloading a device pack, which we did. However when we ran it on the call manager server it gave the error "unable to read script" Any recommendations on how to get these phones working with our Call Manager? Thank you.

  Read the article

• Watchguard Firebox "split" fibre optic line into 2 interfaces

  - by fRAiLtY-

  We have a requirement on our Watchguard Firebox XTM505 to be able to split our incoming external interface, in this case a fibre optic dedicated leased line, 100/100. We use the line in our office of approx 30 machines however we also re-sell to an external company who utilise it to provide wireless internet solutions to the public. The current infrastructure is as follows: Data in (Leased Line) - Juniper SRX210 managed by ISP - 1 cable out into unmanaged Netgear switch - 1 cable into our firewall and office network, 1 cable to our external providers core router managed by them. We have been informed that having the unmanaged switch in the position it is poses a security risk and that a good option would be to get our Watchguard Firewall to perform the split, by separating our office onto a trusted interface, and by "passing through" the external line to their managed router. It is alleged that the Watchguard is capable of doing this and also rate limiting the interfaces, i.e. 20mbps for the trusted interface and 80mbps for the "pass-through", however Watchguard technical support don't seem to be able to understand what we're trying to achieve. Can anyone provide any advice on whether this is possible on a Watchguard device and how or perhaps if there's a better way of achieving this, perhaps with a managed switch instead of unmanaged? Cheers

  Read the article

• Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

  - by Fazil

  I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

  Read the article

• How to tell Linux to explicitly swap out main memory of suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• Is there a monitoring software suite that will alert me if it has received no activity in a time period?

  - by matt b

  This might be a very basic question, but I am not very familiar with the exact features of Nagios versus Munin versus other monitoring tools. Let's say we have a process that needs to run daily for some very important infrastructure reasons. We've had cases where the process did not run or was otherwise down for a number of days before anyone noticed. I'd like to set up a system that will enable me to easily know when the daily run did not take place for some reason. I can set up this process to send an email on every successful run (or every failed run), but I do not trust that the people receiving this email would notice an absence of an "I'm OK" message. What I am envisioning is some type of "tripwire" service which this V.I.P. (very-important-process) can send a status message to each time it runs, whether successfully or not; and if the "tripwire" service has not received any word from the VIP within a configurable amount of time, it can then send an alert to someone. (The difference between what I envision and the first approach I outlined is a service that sends a message only in abnormal conditions, rather than a service that sends messages each day that the status is normal/OK). Can Nagios be set up to send an alert like this, if it has not heard from a certain service/device/process in N days? Is there another tool out there which does have this feature?

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks.

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• Input/output error reading USB backup drive on CentOS 6.4

  - by Kev

  I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

  Read the article

• Windows 8 install app for multiple user accounts

  - by Robert Graves

  I purchased Adera episode 2 intending to play through it with my son. We each have our own user account on the same PC. When my son logged in, he was prompted to purchase the app which I had already purchased, installed, and played on the same PC. So I checked the Terms of Use. After selecting an app in the store, there is a Terms of Use link on the left side under the Install button. It is almost impossible to identify it as a link unless you put your mouse over it. The Terms of Use are standard across all apps in the store, not specific to particular apps. The terms of use indicates that the app may be installed on up to five devices, but says nothing about multiple user accounts on those devices. However, this Microsoft blog article indicates that it is allowed. Say, for example, that your family has a shared PC. You have previously used your Microsoft account to purchase a game that all your kids like to play. You can install it for each of your kids by having each of them sign in to their Windows accounts on the shared PC, then launch the Store and sign in to the Store using your own Microsoft account. There, you’ll see all your apps and you can re-install the app on your kid’s Windows account. Installing apps on multiple user accounts on a shared PC still only counts as one of the five allowable PCs where you can install apps. So I have two questions: Is it permissible under the Terms of Use to install the app under multiple accounts on the same device? If so, how do I do so given that my son has already signed into the store using his own Microsoft account.

  Read the article

• Microphone doesn't work

  - by mandy

  I'm having a trouble with my built in microphone. Even if I use headphone with mic, it doesn't really work. The weird thing is, if I clap the green lines of the speaker icon jumps, but if I speak it doesn't. I have also tried some recordings, but I can not hear myself and adjusting the volume didn't help at all. I tried to restore it, still no change. I have updated it in the device manager, but it said there that it's up to date and the devices are working properly. Until I decided to recover the whole system (wherein I pressed zero and switch on button) to my surprise, the settings became different, most programs were deleted, even my files. It's like it was formatted and I'm so sad that the mic was not fixed. I really don't know what to do now. My laptop model is Toshiba satellite m840. I want to it return to its settings/set up just before I Recover the system and bring back all the programs that we're installed and of course, most of all, to fix my microphone so I can use Skype again and other video calling application.. I hope someone could help me. Thanks a lot!

  Read the article

< Previous Page | 877 878 879 880 881 882 883 884 885 886 887 888  | Next Page >